BS.22 Alzavola | |
---|---|
Role | Motor glider |
National origin | Italy |
Manufacturer | Aeronautica Bonomi |
Designer | Camillo Silva |
First flight | 1934 |
Number built | 1 |
Developed from | Bonomi BS.15 Bigiarella |
The Bonomi BS.22 Alzavola (English: Teal ) was a training motor glider, intended to acquaint capable glider pilots with the characteristics of powered aircraft. The sole example was designed and built in Italy in the mid-1930s. [1]
The BS.22 was evolved from the earlier Bonomi BS.15 Bigiarella glider, though with the addition of a small flat twin engine which drove a pusher propeller. It also had a retractable wheeled conventional undercarriage and a quite different tail. [2] Intended as an inexpensive aircraft, it was Bonomi and Silva's second and last motor glider, the other being the Bonomi BS.19 Alca. [2] The Alzavola was intended to introduce glider pilots with C or B certificates to the complications of powered aircraft. In particular, as well as the retractable conventional undercarriage it had a standard glider landing skid so new pilots could take-off on wheels, retract them and land on the skid in the way they were used to. After becoming familiar with the Alzavola they could put the wheels down before landing. [3]
The wing had a constant chord, unswept central section and straight tapered outer panels with rounded tips. The outer panels' trailing edges were entirely filled with the ailerons. The centre section was supported over the fuselage on a pedestal, which also supported the small flat twin engine slightly above the wing surface, neatly cowled but with its cylinder heads exposed for cooling. Its pusher propeller rotated in a rectangular trailing edge cut-out, at about 70% chord. On each side an asymmetric V-strut, mounted on the lower fuselage longeron immediately below the forward wing spar, supported the outer ends of the centre section, joining its two spars. [2]
The fuselage was flat sided and essentially rectangular, though there was decking to fair in the open cockpit, which had a small windshield, and a dorsal fairing to merge the rear of the pedestal to the tail. Under the cockpit, where the fuselage was deepest, there was a typical glider landing skid. Its conventional undercarriage had two balloon tyre mainwheels, each mounted on V-form split axles attached to the skid and with a shock absorbing strut fixed to the lower longeron. At the rear there was a tailskid. Both tail surfaces were straight tapered and straight cropped. Both rear control surfaces were much larger in area than their fixed counterparts and balanced; the rudder extended to the keel and operated in an elevator cut-out as the tailplane was mounted on the fin just above the fuselage, braced from above and below. [2]
The Alzavola could take off under its own power but could also be launched, with its wheeled undercarriage retracted or removed, by bungee cord, winch or air-tow. [2]
Data from Pedrielli (2011) p.103 [2]
General characteristics
Performance
The Bonomi BS.2 Balestruccio was an Italian sailplane designed to set records. In 1932 it set a new national endurance record with a flight of over 25 minutes.
The Bonomi BS.4 Basettino was a primary glider designed and built in Italy in the 1930s.
The Bonomi BS.5 Ballerina was a single seat, medium performance training glider designed and built in Italy in the 1930s.
The Bonomi BS.7 Allievo Italia was a single seat, primary glider designed and built in Italy in the 1920s.
The Bonomi BS.9 Bertina II was a single seat glider with a layout somewhere between that of a flying wing and the conventional, tail stabilized arrangement. A single example was designed and built in Italy in the 1930s.
The Bonomi BS.10 Ardea was an Italian single seat high performance glider, designed and built in the mid-1930s. Only one was built.
The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.
The Bonomi BS.14 Astore was a two-seat training and aerobatic glider, designed and built in Italy in 1935. Only one was constructed.
The Bonomi BS.15 Bigiarella, originally named the Bonomi BS.6 Bigiarella was a single seat glider, designed and built in Italy in 1934. Only three were constructed.
The Bonomi BS.17 Allievo Cantù was a single seat training glider, designed and built in Italy in 1934 and widely used by flying clubs.
The Bonomi BS.18 Airone was a single seat training glider, designed in Italy in 1936. Only one was built.
The Bonomi BS.19 Alca was a single seat, tractor configuration motor glider, designed and built in Italy shortly before World War II. It had an unusual retractable undercarriage used only for take-offs. Only one was built.
The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.
The Caproni Vizzola MF and 2 were single-seat gliders built in Italy just before World War II. Intended as training aircraft capable of aerobatics, the two variants differed only in their fuselages. Only one of each was built, but they were both successful in Italian competitions.
The Teichfuss LT.12 Biposto was an Italian tandem seat primary glider designed by Luigi Teichfuss and flown in 1933.
The Teichfuss Cicogna was an Italian tailless single-seat motor glider designed by Luigi Teichfuss and flown in 1936.
The Teichfuss Balilla was an Italian single seat primary glider, designed by Luigi Teichfuss and flown in 1939.
The Avia 50-MP was a French motor glider based on that of the Avia XV-A training glider. First flown in 1934, it was intended to introduce pilots to motor-gliders.
The Avia 60-MP was a French motor glider with a wing based on that of the Avia 32-E, an advanced training glider. It was intended as both an advanced trainer and as an atmospheric research aircraft.
The RRG Delta I was a German experimental tailless aircraft flown in the early 1930s first as a glider and then powered. It was one of the first delta wing aircraft.