This article needs additional citations for verification .(July 2010) |
Coalbed methane (CBM or coal-bed methane), [1] coalbed gas, or coal seam gas (CSG [1] ) is a form of natural gas extracted from coal beds. [2] In recent decades it has become an important source of energy in United States, Canada, Australia, and other countries.
The term refers to methane absorbed into the solid matrix of the coal. It is called 'sweet gas' because of its lack of hydrogen sulfide. The presence of this gas is well known from its occurrence in underground coal mining, where it presents a serious safety risk. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoir, as the methane is stored within the coal by a process called adsorption. The methane is in a near-liquid state, lining the inside of pores within the coal (called the matrix). The open fractures in the coal (called the cleats) can also contain free gas or can be saturated with water.[ citation needed ]
Unlike much natural gas from conventional reservoirs, coalbed methane contains very little heavier hydrocarbons such as propane or butane, and no natural-gas condensate. It often contains up to a few percent carbon dioxide. Coalbed methane is generally formed due to thermal maturation of kerogen and organic matter, in contrast to coal seams with regular groundwater recharge where methane is typically generated by microbial communities living in situ. [3] [4]
Coalbed methane grew out of venting methane from coal seams. Some coal beds have long been known to be "gassy," and as a safety measure, boreholes were drilled into the seams from the surface, and the methane allowed to vent before mining.
Coalbed methane as a natural-gas resource received a major push from the US federal government in the late 1970s. Federal price controls were discouraging natural gas drilling by keeping natural gas prices below market levels; at the same time, the government wanted to encourage more gas production. The US Department of Energy funded research into a number of unconventional gas sources, including coalbed methane. Coalbed methane was exempted from federal price controls, and was also given a federal tax credit.
In Australia, commercial extraction of coal seam gas began in 1996 in the Bowen Basin of Queensland. [5]
Gas contained in coal bed methane is mainly methane and trace quantities of ethane, nitrogen, carbon dioxide and few other gases. Intrinsic properties of coal as found in nature determine the amount of gas that can be recovered.
Coalbed methane reservoirs are considered as a dual-porosity reservoirs. Dual porosity reservoirs are reservoirs in which porosity related to cleats (natural fractures) are responsible for flow behavior and reservoir porosity of the matrix is responsible for the storage of gas. The porosity of a coalbed methane reservoir can vary from 10%-20%; However, the cleat porosity of the reservoir is estimated to be in the range of 0.1%-1% [6]
Adsorption capacity of coal is defined as the volume of gas adsorbed per unit mass of coal usually expressed in SCF (standard cubic feet, the volume at standard pressure and temperature conditions) gas/ton of coal. The capacity to adsorb depends on the rank and quality of coal. The range is usually between 100 and 800 SCF/ton for most coal seams found in the US. Most of the gas in coal beds is in the adsorbed form. When the reservoir is put into production, water in the fracture spaces is pumped off first. This leads to a reduction of pressure enhancing desorption of gas from the matrix. [7]
Fracture permeability acts as the major channel for the gas to flow. The higher the permeability, the higher the gas production. For most coal seams found in the US, the permeability lies in the range of 0.1–50 milliDarcys. The permeability of fractured reservoirs changes with the stress applied to them. Coal displays a stress-sensitive permeability and this process plays an important role during stimulation and production operations [8] [ citation needed ]. [9] Fracture permeability in Coalbed methane reservoir tends to increase with depletion of gas; in contrast to conventional reservoirs. This unique behavior is because of shrinking of coal, when methane is released from its matrix, which results in opening up of fractures and increased permeability. [10] It is also believed that due to shrinkage of coal matrix at lower reservoir pressures, there is a loss of horizontal stress in the reservoir which induces in-situ failure of coal. Such a failure has been attributed to sudden decrease in the fracture permeability of the reservoir [11] [9]
The thickness of the formation may not be directly proportional to the volume of gas produced in some areas.[ citation needed ]
For example, it has been observed in the Cherokee Basin in Southeast Kansas that a well with a single zone of 1 to 2 feet (0.3 to 0.6 m) of pay can produce excellent gas rates, whereas an alternative formation with twice the thickness can produce next to nothing. Some coal (and shale) formations may have high gas concentrations regardless of the formation's thickness, probably due to other factors of the area's geology.[ citation needed ]
The pressure difference between the well block and the sand face should be as high as possible as is the case with any producing reservoir in general.[ citation needed ]
Other affecting parameters include coal density, initial gas-phase concentration, critical gas saturation, irreducible water saturation, relative permeability to water and gas at conditions of Sw = 1.0 and Sg = 1-Sw irreducible respectively.[ citation needed ]
To extract the gas, a steel-encased hole is drilled into the coal seam 100 to 1,500 metres (330 to 4,920 ft) below ground. As the pressure within the coal seam declines due to natural production or the pumping of water from the coalbed, both gas and produced water come to the surface through tubing. Then the gas is sent to a compressor station and into natural gas pipelines. The produced water is either reinjected into isolated formations, released into streams, used for irrigation, or sent to evaporation ponds. The water typically contains dissolved solids such as sodium bicarbonate and chloride but varies depending on the formation geology. [12]
Coalbed methane wells often produce at lower gas rates than conventional reservoirs, typically peaking at near 300,000 cubic feet (8,500 m3) per day (about 0.100 m³/s), and can have large initial costs. The production profiles of CBM wells are typically characterized by a "negative decline" in which the gas production rate initially increases as the water is pumped off and gas begins to desorb and flow. A dry CBM well is similar to a standard gas well.[ citation needed ]
The methane desorption process follows a curve (of gas content vs. reservoir pressure) called a Langmuir isotherm. The isotherm can be analytically described by a maximum gas content (at infinite pressure), and the pressure at which half that gas exists within the coal. These parameters (called the Langmuir volume and Langmuir pressure, respectively) are properties of the coal, and vary widely. A coal in Alabama and a coal in Colorado may have radically different Langmuir parameters, despite otherwise similar coal properties.[ citation needed ]
As production occurs from a coal reservoir, the changes in pressure are believed to cause changes in the porosity and permeability of the coal. This is commonly known as matrix shrinkage/swelling. As the gas is desorbed, the pressure exerted by the gas inside the pores decreases, causing them to shrink in size and restricting gas flow through the coal. As the pores shrink, the overall matrix shrinks as well, which may eventually increase the space the gas can travel through (the cleats), increasing gas flow.[ citation needed ]
The potential of a particular coalbed as a CBM source depends on the following criteria. Cleat density/intensity: cleats are joints confined within coal sheets. They impart permeability to the coal seam. A high cleat density is required for profitable exploitation of CBM. Also important is the maceral composition: maceral is a microscopic, homogeneous, petrographic entity of a corresponding sedimentary rock. A high vitrinite composition is ideal for CBM extraction, while inertinite hampers the same.[ citation needed ]
The rank of coal has also been linked to CBM content: a vitrinite reflectance of 0.8–1.5% has been found to imply higher productivity of the coalbed.[ citation needed ]
The gas composition must be considered, because natural gas appliances are designed for gas with a heating value of about 1,000 BTU (British thermal units) per cubic foot, or nearly pure methane. If the gas contains more than a few percent non-flammable gases such as nitrogen or carbon dioxide, either these will have to be removed or it will have to be blended with higher-BTU gas to achieve pipeline quality. If the methane composition of the coalbed gas is less than 92%, it may not be commercially marketable.[ citation needed ]
As with all carbon-based fossil fuels, burning coalbed methane releases carbon dioxide (CO2) into the atmosphere. Its effect as greenhouse gas was first analyzed by chemist and physicist Svante Arrhenius. CBM production also entails leaks of fugitive methane into the atmosphere. Methane is rated as having 72 times the effect on global warming per unit of mass than CO2. over 20 years, reducing to 25 times over 100 years and 7.5 times over 500 years. [13] Analysis of life-cycle greenhouse gas emissions of energy sources indicates that generating electricity from CBM, as with conventional natural gas, has less than half the greenhouse gas effect of coal. [14]
Multiple Australian studies have indicated the long term negative environmental effects of coal seam gas extraction, both locally and globally. [15] [16] [17] [18] [19]
In the United States, methane escaping from coal during mining amounts to seven percent of total methane emissions. [20] Recovery of coal mine methane in advance of mining is seen as a major opportunity to reduce methane emissions. [ citation needed ] Companies like CNX Resources have methane abatement programs to reduce greenhouse gas emissions from active and closed mines. [21]
CBM wells are connected by a network of roads, pipelines, and compressor stations. Over time, wells may be spaced more closely in order to extract the remaining methane.
The produced water brought to the surface as a byproduct of gas extraction varies greatly in quality from area to area, but may contain undesirable concentrations of dissolved substances such as salts, naturally present chemicals, heavy metals and radionuclides. [22] In many producing regions the water is treated, such as through a Reverse Osmosis plant and used beneficially for irrigation, water for livestock, urban and industrial uses, or dust suppression.
In 2012 Eastern Star Gas was fined for "discharging polluting water containing high levels of salt into Bohena Creek" in the Pilliga Scrub. [23] There were "16 spills or leaks of contaminated water" including "serious spills of saline water into woodland and a creek." [24] In 2012, a NSW Legislative Council [25] inquiry criticised the use of open holding ponds, recommending that "the NSW Government ban the open storage of produced water." [25] [26]
Not all coalbed methane produced water is saline or otherwise undesirable. Water from coalbed methane wells in the Powder River Basin of Wyoming, US, commonly meets federal drinking water standards, and is widely used in the area to water livestock. [27] Its use for irrigation is limited by its relatively high sodium adsorption ratio.
Depending on aquifer connectivity, water withdrawal may depress aquifers over a large area and affect groundwater flows. [28] In Australia, the CBM industry estimates extraction of 126,000 million litres (3.3×1010 US gallons) to 280,000 million litres (7.4×1010 US gallons) of groundwater per year; while the National Water Commission estimates extraction above 300,000 million litres (7.9×1010 US gallons) a year. [22]
In 2012, the Aspen Skiing Company built a 3-megawatt methane-to-electricity plant in Somerset, Colorado at Oxbow Carbon's Elk Creek Mine. [29]
Coal Seam Gas resources are in the major coal basins in Queensland and New South Wales, with further potential resources in South Australia. Commercial recovery of coal seam gas (CSG) began in Australia in 1996. As of 2014, coal seam gas, from Queensland and New South Wales, made up about ten percent of Australia's gas production. Demonstrated reserves were estimated to be 33 trillion cubic feet (35 905 petajoules) as of January 2014. [30]
In Canada, British Columbia is estimated to have approximately 90 trillion cubic feet (2.5 trillion cubic metres) of coalbed gas. Alberta, in 2013, was the only province with commercial coalbed methane wells and is estimated to have approximately 170 trillion cubic feet (4.8 trillion cubic metres) of economically recoverable coalbed methane, with overall reserves totaling up to 500 trillion cubic feet (14 trillion cubic metres). [31] [32]
Coalbed methane is considered a non-renewable resource, although the Alberta Research Council, Alberta Geological Survey and others have argued coalbed methane is a renewable resource because the bacterial action that formed the methane is ongoing.[ citation needed ] This is subject to debate since it has also been shown that the dewatering that accompanies CBM production destroys the conditions needed for the bacteria to produce methane [33] and the rate of formation of additional methane is undetermined. This debate is currently causing a right of ownership issue in the Canadian province of Alberta, as only non-renewable resources can legally be owned by the province. [34]
Although gas in place in Britain's coal fields has been estimated to be 2,900 billion cubic meters, it may be that as little as one percent might be economically recoverable. Britain's CBM potential is largely untested. Some methane is extracted by coal mine venting operations, and burned to generate electricity. Assessment by private industry of coalbed methane wells independent of mining began in 2008, when 55 onshore exploration licences were issued, covering 7,000 square kilometers of potential coalbed methane areas. IGas Energy became the first in the UK to commercially extract coalbed methane separate from mine venting; as of 2012, the Igas coalbed methane wells at Doe Green, extracting gas for electrical generation, were the only commercial CBM wells in the UK. [35] The use of CBM (in GWh) for electricity generation in the UK is as shown. [36]
Graphs are unavailable due to technical issues. There is more info on Phabricator and on MediaWiki.org. |
United States coalbed methane production in 2017 was 1.76 trillion cubic feet (TCF), 3.6 percent of all US dry gas production that year. The 2017 production was down from the peak of 1.97 TCF in 2008. [37] Most CBM production came from the Rocky Mountain states of Colorado, Wyoming, and New Mexico.
Kazakhstan could witness the development of a large coalbed methane (CBM) sector over the coming decades, according to industry professionals. [38] Preliminary research suggests there may be as much as 900 billion m3 of gas in Kazakhstan's main coalfields – 85% of all reserves in Kazakhstan.
Great Eastern Energy (GEECL) was the first company with a field development plan approved. With the completion of the drilling of 23 vertical production wells by GEECL, coalbed methane became commercially available in India on 14 July 2007 with CNG priced at ₹30 per kg. Initially 90% of the CBM would be distributed as CNG gas to fuel vehicles.
GEECL is responsible for Southeast Asia's first CBM station and is also locating one in the West Bengal city of Asansol.
Prashant Modi, President and Chief Operating Officer of GEECL, said, "With the nation requiring higher energy sources to sustain its development pace, we are confident that CBM will play an important role as one of the prime energy sources for the future generations." [39]
Essar Group's Essar Oil and Gas Exploration and Production Ltd.'s CBM portfolio includes 5 blocks. Currently, only one of them, Raniganj East, is currently operational. The others include Rajmahal in Jharkhand, Talcher and Ib Valley in Odisha and Sohagpur in Madhya Pradesh. The 5 blocks possess an estimated 10 trillion cubic feet (CBF) of CBM reserves.
Natural gas is a naturally occurring mixture of gaseous hydrocarbons consisting primarily of methane (95%) in addition to various smaller amounts of other higher alkanes. Traces of carbon dioxide, nitrogen, hydrogen sulfide, and helium are also usually present. Methane is colorless and odorless, and the second largest greenhouse gas contributor to global climate change after carbon dioxide. Because natural gas is odorless, odorizers such as mercaptan are commonly added to it for safety so that leaks can be readily detected.
Coalbed methane extraction is a method for extracting methane from a coal deposit. Coal bed methane (CBM) is one of the factors restricting the safe production of coal in underground coal mines. It is also a form of high-quality energy that can be used in many fields such as power generation, heating, and chemical industries. CBM extraction is therefore carried out before extraction with a view of increasing the safety of mining coal beds, and as a useful energy resource to be exploited.
A petroleum reservoir or oil and gas reservoir is a subsurface accumulation of hydrocarbons contained in porous or fractured rock formations. Such reservoirs form when kerogen is created in surrounding rock by the presence of high heat and pressure in the Earth's crust.
Underground coal gasification (UCG) is an industrial process which converts coal into product gas. UCG is an in-situ gasification process, carried out in non-mined coal seams using injection of oxidants and steam. The product gas is brought to the surface through production wells drilled from the surface.
The Western Canada Sedimentary Basin (WCSB) underlies 1.4 million square kilometres (540,000 sq mi) of Western Canada including southwestern Manitoba, southern Saskatchewan, Alberta, northeastern British Columbia and the southwest corner of the Northwest Territories. This vast sedimentary basin consists of a massive wedge of sedimentary rock extending from the Rocky Mountains in the west to the Canadian Shield in the east. This wedge is about 6 kilometres (3.7 mi) thick under the Rocky Mountains, but thins to zero at its eastern margins. The WCSB contains one of the world's largest reserves of petroleum and natural gas and supplies much of the North American market, producing more than 450 million cubic metres per day of gas in 2000. It also has huge reserves of coal. Of the provinces and territories within the WCSB, Alberta has most of the oil and gas reserves and almost all of the oil sands.
Reservoir simulation is an area of reservoir engineering in which computer models are used to predict the flow of fluids through porous media.
Natural gas has been used almost as long as crude oil in Canada, but its commercial development was not as rapid. This is because of special properties of this energy commodity: it is a gas, and it frequently contains impurities. The technical challenges involved to first process and then pipe it to market are therefore considerable. Furthermore, the costs of pipeline building make the whole enterprise capital intensive, requiring both money and engineering expertise, and large enough markets to make the business profitable.
Shale gas is an unconventional natural gas that is found trapped within shale formations. Since the 1990s a combination of horizontal drilling and hydraulic fracturing has made large volumes of shale gas more economical to produce, and some analysts expect that shale gas will greatly expand worldwide energy supply.
The Piceance Basin is a geologic structural basin in northwestern Colorado, in the United States. It includes geologic formations from Cambrian to Holocene in age, but the thickest section is made up of rocks from the Cretaceous Period. The basin contains reserves of coal, natural gas, and oil shale. The name likely derives from the Shoshoni word /piasonittsi/ meaning “tall grass”.
Well stimulation is a broad term used to describe the various techniques and well interventions that can be used to restore or enhance the production of hydrocarbons from an oil well.
The Cahaba Basin is a geologic area of central Alabama developed for coal and coalbed methane (CBM) production. Centered in eastern Bibb and southwestern Shelby Counties, the basin is significantly smaller in area and production than the larger Black Warrior Basin in Tuscaloosa and western Jefferson Counties to the northwest. The coalbed methane is produced from the Gurnee Field of the Pottsville Coal Interval. Coalbed gas production has been continuous since at least 1990 and annual gas production has increased from 344,875 Mcf in 1990 to 3,154, 554 Mcf through October 2007.
The Sacred Headwaters is a large subalpine drainage basin centred around Klappan Mountain of the Klappan Range in northern British Columbia. It is the source of three wild salmon rivers: the Skeena River, Nass River, and Stikine River. It is also referred to as the Klappan Valley, although the Klappan—a tributary of the Stikine River—is only one of the area's watersheds. Local Tahltan people call the area Klabona, which is loosely translated as "headwaters".
Shale gas in the United States is an available source of unconventional natural gas. Led by new applications of hydraulic fracturing technology and horizontal drilling, development of new sources of shale gas has offset declines in production from conventional gas reservoirs, and has led to major increases in reserves of U.S. natural gas. Largely due to shale gas discoveries, estimated reserves of natural gas in the United States in 2008 were 35% higher than in 2006.
Tight gas is commonly used to refer to natural gas produced from reservoir rocks with such low permeability that massive hydraulic fracturing is necessary to produce the well at economic rates. The gas is sealed in very impermeable and hard rocks, making their formation "tight". These impermeable reservoirs which produce dry natural gas are also called "Tight Sand".
Tight oil is light crude oil contained in unconventional petroleum-bearing formations of low permeability, often shale or tight sandstone. Economic production from tight oil formations requires the same hydraulic fracturing and often uses the same horizontal well technology used in the production of shale gas. While sometimes called "shale oil", tight oil should not be confused with oil shale or shale oil. Therefore, the International Energy Agency recommends using the term "light tight oil" for oil produced from shales or other very low permeability formations, while the World Energy Resources 2013 report by the World Energy Council uses the terms "tight oil" and "shale-hosted oil".
Fracking is a well stimulation technique involving the fracturing of formations in bedrock by a pressurized liquid. The process involves the high-pressure injection of "fracking fluid" into a wellbore to create cracks in the deep-rock formations through which natural gas, petroleum, and brine will flow more freely. When the hydraulic pressure is removed from the well, small grains of hydraulic fracturing proppants hold the fractures open.
The Zonguldak basin of northwestern Turkey is the only basin in Turkey with mineable coal deposits. It has been mined for coal since the late 1800s. The basin takes its name after Zonguldak, Turkey, and lies at approximately 41° N. It is roughly elliptical in shape with its long axis oriented roughly southwest to northeast, and is adjacent to the Black Sea. Three main regions have been recognized in the Zonguldak basin: from west to east, Armutcuk, Zonguldak, and Amasra.
The 2017 production of coalbed methane in the United States was 0.98 trillion cubic feet (TCF), 3.6 percent of all US dry gas production that year. The 2017 production was down from the peak of 1.97 TCF in 2008. Most coalbed methane production came from the Rocky Mountain states of Colorado, Wyoming, and New Mexico.
Great Eastern Energy Corporation Limited is a Coalbed methane (CBM) production company, located in Asansol district of West Bengal. With two CBM blocks, one in Raniganj, West Bengal, and the other in Mannargudi, Tamil Nadu. Great Eastern Energy Corporation has played an important role in providing methane gas. The wells dug in the respective blocks are well connected with gas gathering stations and the gas is fed into its dedicated steel pipeline network to maintain the supply.
Unconventional reservoirs, or unconventional resources are accumulations where oil and gas phases are tightly bound to the rock fabric by strong capillary forces, requiring specialized measures for evaluation and extraction.
{{cite web}}
: CS1 maint: bot: original URL status unknown (link){{cite web}}
: CS1 maint: bot: original URL status unknown (link){{cite news}}
: CS1 maint: bot: original URL status unknown (link){{cite news}}
: CS1 maint: bot: original URL status unknown (link){{cite web}}
: CS1 maint: bot: original URL status unknown (link)