Douglas XCG-17

Last updated

XCG-17
Douglas XCG-17 in flight.jpg
The XCG-17 during towed flight
General information
Type Assault glider
National origin United States
Manufacturer Douglas Aircraft
Primary user United States Army Air Forces
Number built1
Construction number4588
Registration N69030
XA-JID
XC-0PS
Serial 41-18496
History
First flightJune 14, 1944
Developed from Douglas C-47 Skytrain

The Douglas XCG-17 was an American assault glider, developed by the conversion of a C-47 Skytrain twin-engine transport during World War II. Although the XCG-17 was successfully tested, the requirement for such a large glider had passed, and no further examples of the type were built; one additional C-47, however, was converted in the field to glider configuration briefly during 1946 for evaluation, but was quickly reconverted to powered configuration.

Contents

Design and development

With the introduction of the Douglas C-54 Skymaster four-engined transport aircraft, the United States Army Air Forces, observing that conventional gliders then in service [N 1] would be an inefficient use of the C-54's power and capacity, determined that a requirement existed for a new, much larger assault glider. [2] [3] It was determined that the best solution to the requirement was the conversion of the Douglas C-47 Skytrain, already in large-scale production, to meet the requirement. The C-47 could be converted to a glider configuration with minimal alteration to the airframe, and would provide the required capacity. [3]

Trials conducted using a conventional, powered C-47, first conducting ordinary deadstick landings, then being towed by another C-47, indicated that the scheme was feasible. [2] Therefore, a C-47-DL was taken in hand for conversion into a glider, which was given the designation XCG-17. [4] [5] [N 2] The aircraft, formerly a Northwest Airlines DC-3 that had been impressed into military service at the start of World War II, [7] [N 3] was modified by the removal of the aircraft's engines; the nacelles, containing the landing gear, remained in place, covered with aerodynamically profiled hemispherical domes for streamlining, containing fixed weight to compensate for the removal of the engines. [3] [7] [9] Other equipment, no longer necessary with the conversion to an unpowered configuration, was also removed to save weight; [3] items removed included the aircraft's wiring and bulkheads, along with the navigator's and radio operator's positions. [1] [7]

Operational history

The C-54 was the preferred tow aircraft for the XCG-17 Douglas C-54D USAAF wartime markings Chico CA 08.10.92.jpg
The C-54 was the preferred tow aircraft for the XCG-17

The conversion, carried out at Clinton County Army Air Field, was completed on June 12, 1944, with the aircraft undergoing its initial flight test shortly thereafter. [7] The flight testing of the XCG-17 proved that the aircraft was satisfactory; compared with conventional gliders in service, the aircraft possessed lower stalling and higher towing speeds than conventional gliders, as well as gliding at a significantly shallower angle. [4] [10] Tow tests were conducted using a variety of aircraft; the most commonly used configuration was a tandem tow by two C-47s, with the towing aircraft coupled one in front of the other and the leading aircraft detaching following takeoff. [3] This configuration was dangerous for the "middle" C-47, however, [7] and it was determined that a single C-54 was the optimal tug aircraft. [2] [7]

The XCG-17's cargo hold had a capacity of 15,000 pounds (6,800 kg); [1] [7] [9] alternatively, up to 40 fully equipped troops could be transported, these figures being significantly larger than conventional gliders' capacity. [3] The XCG-17 was also capable of carrying three jeeps in a single load, or alternatively two 105-millimetre (4.1 in) howitzers. [7] Regardless of the aircraft's load, no ballast was required to maintain the aircraft's center of gravity, [3] a trait unique among American assault gliders. [7]

Despite the satisfactory results in testing, however, the aircraft failed the Army's requirement that it be capable of landing on unimproved fields; [7] in addition, by the time the XCG-17's evaluation was completed the need for such a large assault glider had passed. [1] [9] The primary role for the glider had been intended to increase the amount of supplies that could be carried to China over "The Hump"; the war situation had, however, become more favorable and the added capacity an oversized glider would provide was no longer necessary. [11] No further examples of the type were produced; the prototype, its trials complete, was placed in storage, being ferried to Davis-Monthan Air Force Base for disposal in August 1946. [7]

In August 1949, the aircraft was sold to Advance Industries, its engines being reinstalled to return the aircraft to powered status in DC-3C configuration. [7] Some sources, however, indicate that the XCG-17 was reconverted to C-47 configuration in 1946. [9] Following its restoration to powered status, the aircraft was transferred to Mexico, [7] where it remained in civilian service until 1980. [12]

Field conversion

"Nez Perce"
Douglas CG-47.png
"Nez Perce" after conversion to glider configuration
General information
Other name(s)XCG-47; XCG-17
TypeField-converted glider
Serial 43-16229
History
Manufactured1946
First flightJune 17, 1946 (as glider)
FateReconverted to C-47

|}

Although the XCG-17 failed to lead to any production of a C-47 derived glider type, a single C-47 was converted in the field to glider configuration by the Fifth Air Service Area Command, located at Nichols Field on Luzon in the Philippines, during January 1946. [7] Carried out in much the same manner as the XCG-17, the conversion included octagonally shaped fairings over the engine mountings, with an auxiliary power unit from a B-24 Liberator bomber being installed. [7]

Referred to as "XCG-47" as well as "XCG-17", and named "Nez Perce", [7] the aircraft undertook its initial flight following conversion on June 17, 1946, towed by a C-54. [7] The flight tests of the field-converted aircraft proved favorable, and an ambitious flight, towing the aircraft from Luzon to Tokyo in Japan, was planned. [7] This flight was intended to prove the suitability of large gliders to act as an "aerial freight train" for regular transport. [7]

The flight, conducted in late June 1946, took 11 hours of flight time and included an overnight stay on Okinawa; covering 1,800 miles (2,900 km), it concluded at Tachikawa Airfield near Tokyo. [7] Despite the success of the flight, the "aerial freight train" concept did not catch on; the aircraft had its engines re-fitted in August 1946 and was returned to service as a normal C-47. [7]

Operators

Military (as C-47, then XCG-17)

Flag of the United States (1912-1959).svg  United States

Civilian (as DC-3C)

Flag of Mexico.svg  Mexico

Specifications (41-18496)

Data from [3] [11] [13]

General characteristics

Performance

See also

Related development

Aircraft of comparable role, configuration, and era

Related lists

Related Research Articles

<span class="mw-page-title-main">Douglas DC-3</span> Airliner and military transport aircraft family

The Douglas DC-3 is a propeller-driven airliner manufactured by Douglas Aircraft Company, which had a lasting effect on the airline industry in the 1930s to 1940s and World War II. It was developed as a larger, improved 14-bed sleeper version of the Douglas DC-2. It is a low-wing metal monoplane with conventional landing gear, powered by two radial piston engines of 1,000–1,200 hp (750–890 kW). Although the DC-3s originally built for civil service had the Wright R-1820 Cyclone, later civilian DC-3s used the Pratt & Whitney R-1830 Twin Wasp engine. The DC-3 has a cruising speed of 207 mph (333 km/h), a capacity of 21 to 32 passengers or 6,000 lbs (2,700 kg) of cargo, and a range of 1,500 mi (2,400 km), and can operate from short runways.

<span class="mw-page-title-main">McDonnell XF-88 Voodoo</span> Prototype fighter aircraft

The McDonnell XF-88 Voodoo was a long-range, twinjet fighter aircraft with swept wings designed for the United States Air Force. Although it never entered production, its design was adapted for the subsequent supersonic F-101 Voodoo.

<span class="mw-page-title-main">Douglas C-47 Skytrain</span> Military transport aircraft derived from DC-3

The Douglas C-47 Skytrain or Dakota is a military transport aircraft developed from the civilian Douglas DC-3 airliner. It was used extensively by the Allies during World War II. During the war the C-47 was used for troop transport, cargo, paratrooper, for towing gliders and military cargo parachute drops. The C-47 remained in front-line service with various military operators for many years. It was produced in approximately triple the numbers as the larger, much heavier payload Curtiss C-46 Commando, which filled a similar role for the U.S. military.

<span class="mw-page-title-main">Douglas C-54 Skymaster</span> Military transport aircraft derived from DC-4

The Douglas C-54 Skymaster is a four-engined transport aircraft used by the United States Army Air Forces in World War II and the Korean War. Like the Douglas C-47 Skytrain derived from the DC-3, the C-54 Skymaster was derived from a civilian airliner, the Douglas DC-4. Besides transport of cargo, the C-54 also carried presidents, prime ministers, and military staff. Dozens of variants of the C-54 were employed in a wide variety of non-combat roles such as air-sea rescue, scientific and military research, and missile tracking and recovery. During the Berlin Airlift it hauled coal and food supplies to West Berlin. After the Korean War it continued to be used for military and civilian uses by more than 30 countries. It was one of the first aircraft to carry the President of the United States, the first being President Franklin D. Roosevelt during World War II.

<span class="mw-page-title-main">Douglas DC-4</span> Four-engine propeller-driven airliner

The Douglas DC-4 is an American four-engined (piston), propeller-driven airliner developed by the Douglas Aircraft Company. Military versions of the plane, the C-54 and R5D, served during World War II, in the Berlin Airlift and into the 1960s. From 1945, many civil airlines operated the DC-4 worldwide.

<span class="mw-page-title-main">Stinson L-13</span>

The Stinson L-13 was a US military utility aircraft first flown in 1945.

<span class="mw-page-title-main">Northrop XP-79</span> Prototype flying wing fighter aircraft

The Northrop XP-79, USAAF project number MX-365, was a rocket and jet-powered flying wing fighter aircraft, designed by Northrop. The pilot operated the aircraft in a prone position, permitting him to withstand much greater g-forces in pitch. It also used a welded magnesium monocoque structure instead of riveted aluminum.

<span class="mw-page-title-main">Douglas C-74 Globemaster</span> US military transport aircraft with 4 piston engines, 1945

The Douglas C-74 Globemaster was a United States heavy-lift cargo aircraft built by the Douglas Aircraft Company in Long Beach, California. The aircraft was developed after the Japanese attack on Pearl Harbor. The long distances across the Atlantic and, especially, Pacific oceans to combat areas indicated a need for a transoceanic heavy-lift military transport aircraft. Douglas Aircraft Company responded in 1942 with a giant four-engined design. Development and production modifications issues with the aircraft caused the first flight to be delayed until 5 September 1945, after both V-J Day and formal surrender on September 2. Total production was limited to 14 aircraft when the wartime contract was cancelled in January 1946.

<span class="mw-page-title-main">Douglas O-46</span> US military observation aircraft in service 1936-1942

The Douglas O-46 was an observation aircraft used by the United States Army Air Corps and the Philippine Army Air Corps. It entered service in the late 1930s, and saw action in WW2. It became obsolescent later in the war as an observation craft, but was used for liaison, training, and ASW patrols. One airframe has survived as a museum piece into the present day.

<span class="mw-page-title-main">General Airborne Transport XCG-16</span>

The XCG-16 was a military transport/assault glider ordered by the United States Army Air Forces (USAAF), from General Airborne Transport Co., for competition against the Waco CG-13A at Wright Field. The XCG-16’s preferred tow aircraft was the Lockheed Model 18 Lodestar.

<span class="mw-page-title-main">Waco CG-4</span> American WWII glider

The Waco CG-4 was the most widely used American troop/cargo military glider of World War II. It was designated the CG-4A by the United States Army Air Forces, and given the service name Hadrian by the British.

<span class="mw-page-title-main">Chase YC-122 Avitruc</span> Type of aircraft

The Chase XCG-18A and YC-122 Avitruc was a military transport aircraft designed by Chase Aircraft and produced in limited numbers in the United States in the late 1940s, initially as a glider, but definitively in powered form. The design was based on the CG-14 cargo glider but was substantially larger and featured all-metal construction. It was a high-wing cantilever monoplane. The fuselage was of rectangular cross-section and featured a loading ramp at its rear. The main undercarriage units were carried at the sides of the fuselage and were fixed, while the nosewheel was retractable. In its powered form, two radial engines were fitted in nacelles in the wings.

<span class="mw-page-title-main">Chase XCG-20</span> Transport glider, U.S. Air Force, 1950

The Chase XCG-20, also known as the XG-20 and by the company designation MS-8 Avitruc, was a large assault glider developed immediately after World War II by the Chase Aircraft Company for the United States Air Force, and was the largest glider ever built in the United States. The XG-20 did not see production due to a change in USAF requirements, however, it was modified into the successful Fairchild C-123 Provider twin-engined transport aircraft which saw extensive service in the Vietnam War.

<span class="mw-page-title-main">Cornelius XFG-1</span> Type of aircraft

The Cornelius XFG-1 was an American military fuel transporting towed glider, without a tailplane and with a forward-swept wing. Two were built but development ended in 1945.

The St. Louis CG-5 was a 1940s American prototype military transport glider designed and built by the St. Louis Aircraft Corporation.

<span class="mw-page-title-main">Ilyushin Il-18 (1946)</span> Type of aircraft

The Ilyushin Il-18 was a Soviet four-engined airliner designed and built by Ilyushin immediately after World War II. Although the aircraft itself was successful, its Shvetsov ASh-73TK engines were too unreliable for civilian use and were further needed to equip the Tupolev Tu-4 bomber, so it was cancelled in 1948.

<span class="mw-page-title-main">Chase XC-123A</span>

The Chase XC-123A was an experimental transport aircraft developed by Chase Aircraft. The first jet-powered transport built for the United States Air Force, it was intended for use as a high-speed transport for high-priority cargo and personnel. The XC-123A was determined to have insufficient advantages over existing types in service, and did not go into production. The sole prototype was converted into the piston-powered Stroukoff YC-123D to evaluate boundary layer control systems.

<span class="mw-page-title-main">Chase YCG-14</span> Type of aircraft

The Chase CG-14, also known as the G-14 or Model MS.1, was an assault glider manufactured by Chase Aircraft for the United States Army Air Forces during the Second World War. The aircraft failed to progress beyond the prototype stage, being overtaken by larger, improved glider designs.

<span class="mw-page-title-main">Douglas R4D-8</span> Military transport aircraft

The Douglas R4D-8 is a military transport aircraft developed from the civilian Douglas DC-3S airliner. It was used by the United States Navy and United States Marine Corps during the Korean War and Vietnam War.

References

Notes

  1. The Waco CG-4 was the glider most commonly used by the USAAF during World War II. [1]
  2. In the U.S. Army Air Forces' designation scheme, the "-DL" suffix indicated an aircraft built at Douglas' Long Beach, California factory. [6]
  3. A variety of DC-3 series aircraft were impressed into military service at the start of the war. While DC-3 series aircraft constructed for the military were given the designation C-47, impressed aircraft received a variety of designations, including C-47, C-48, C-49, C-50, and C-53, among others. Confusing things further is that the C-53 designation was also assigned to purpose-built military DC-3s, named Skytrooper, that were intended exclusively for personnel transport. [8]

Citations

  1. 1 2 3 4 Nigl and Nigl 2007, pp.16-17.
  2. 1 2 3 Swanborough and Bowers 1989, p.274.
  3. 1 2 3 4 5 6 7 8 Taylor 1991, p.151.
  4. 1 2 Francillon 1988, p.233.
  5. Davis 1995, p.40.
  6. Bowers 1986, p.85.
  7. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Day 2001
  8. Davis 1995, p.31.
  9. 1 2 3 4 Grim 2009, p.17.
  10. Serling 1997, p.62.
  11. 1 2 "XCG-17" (in Russian). Airwar.ru. Retrieved 2011-01-20.
  12. 1 2 Baugher 2010
  13. Francillon 1988

Bibliography

Commons-logo.svg Media related to Douglas XCG-17 at Wikimedia Commons