Toyota AR engine

Last updated
Toyota AR engine
1AR-FE Engine .jpg
Toyota 1AR-FE engine
Overview
Manufacturer Toyota
Production2008–present
Layout
Configuration Inline-4
Chronology
Predecessor
Successor

The AR engine family is an Inline-4 piston engine series by Toyota, first introduced in 2008 for the RAV4, and subsequently for the Highlander, Venza, Camry and Scion tC.

Contents

The AR series uses a die-cast aluminium engine block and aluminium DOHC cylinder head. The engine series shares many of the technologies in the AZ engine, while incorporating features such as variable valve timing on both intake and exhaust camshafts or dual VVT-i, low friction technologies including an offset crankshaft, roller rockers for the valvetrain, a three-stage variable oil pump, reduced-tension piston rings and auxiliary belt drive. An Acoustic Control Induction System switches the length of the intake tract in two stages, based on rpm and throttle angle, thereby ensuring strong torque across a broad engine speed range. New tumble control valves enhances combustion while the engine is cold, and helps to bring the catalytic converters up to working temperature quickly. The Tumble control valves, along with new 12-hole high atomizing long-nozzle fuel injectors, reduce the amount of fuel adhering to the intake ports and therefore maximize fuel economy and reduce harmful emissions.

The cylinder block is an open-deck, midi-skirt type with cast-in iron liners and a die-cast aluminium lower crankcase and a stamped oil pan. The forged steel crankshaft is fully balanced with eight counterweights and supported by five main bearings. A helical gear pressed in No. 3 counterweight drives twin contra-rotating balance shafts in the shaft housing within the lower crankcase.

The AR engine replaces the AZ engine.

1AR-FE

1AR-FE
Overview
Manufacturer Toyota
Production2008-2020 (Unofficial end date)
Layout
Displacement 2,672  cc (163.1  cu in)
Cylinder bore 90  mm (3.543  in)
Piston stroke 105 mm (4.134 in)
Cylinder block material Aluminium alloy
Cylinder head materialAluminium alloy
Valvetrain DOHC
Compression ratio 10.0:1
Combustion
Fuel system EFI
Fuel typePetrol (gasoline)
Cooling system Water cooled
Output
Power output 182–187  bhp (136–139  kW)
Torque output 182–186  lb⋅ft (247–252  N⋅m)

A 2.7 L version of the AR family, first released in the Venza [1] and Highlander in late 2008. [2]

The 1AR-FE most likely ended production in 2020. No official statements were made by Toyota about the engine's status, however, no new cars used this engine after 2020. It was replaced by the A25A-FKS engine.

Applications:

2AR-FE

2AR-FE
2AR-FE 2015 Toyota Camry Atara S.jpg
2AR-FE inside a 2015 Toyota Camry Atara S
(XV50; Australasian model).
Overview
Manufacturer Toyota
Layout
Displacement 2,494 cc (152.2 cu in)
Cylinder bore 90 mm (3.543 in)
Piston stroke 98 mm (3.858 in)
Cylinder block materialAluminium alloy
Cylinder head materialAluminium alloy
Valvetrain DOHC
Compression ratio 10.4:1
Combustion
Fuel system EFI
Fuel typePetrol (gasoline)
Output
Power output 169–180 bhp (126–134 kW)
Torque output 167–173 lb⋅ft (226–235 N⋅m)

A 2.5 L version of the AR family, first released in the RAV4 in the U.S. and Canada in 2008. [3] This engine also replaced the 2AZ-FE in the U.S. and Canada Camry in early 2009, giving 11% better fuel economy. [4] The engine service mass is 324 lb (147 kg) that includes the oil and coolant fully filled. The engine is used in vehicles sold in U.S., Australia, [5] New Zealand, [6] China, Taiwan, Korea, Malaysia, Philippines, Thailand [7] Indonesia, and Middle East.

Applications:

2AR-FXE

The 2AR-FXE [8] is an Atkinson cycle variant of the 2AR-FE. It has the same bore and stroke, but the cams and pistons are unique. Only the intake valves are variable with VVT-i. [9] Geometrical compression ratio is 12.5:1

The large valve overlap leads to a reduction in cylinder charge and reduced torque and power output, but efficiency is increased. This combination makes the 2AR-FXE suitable for use in hybrid vehicles, where peak torque and power demands can be met by the electric motor and battery. Maximum output of the engine when used in the Camry hybrid is 154 hp with 153 lb·ft of torque.

Applications:

2AR-FSE

The 2AR-FSE [10] is a variant of the 2AR-FE equipped with D4-S direct-injection and port injection. It has the same bore and stroke as other 2AR engines but the cylinder head, cams, pistons and fuel management system are unique. Maximum thermal efficiency is about 38.5%. [11] The expansion ratio is 13.0 to 1.

Output in the Toyota Crown hybrid combined is 164 kW (220 hp) at 6000 rpm and 221 N⋅m (163 lbf⋅ft) at 4200–5400 rpm.

Applications:

5AR-FE

5AR-FE
Overview
Manufacturer Toyota
Layout
Displacement 2,494 cc (152.2 cu in)
Cylinder bore 90 mm (3.543 in)
Piston stroke 98 mm (3.858 in)
Cylinder block materialAluminium alloy
Cylinder head materialAluminium alloy
Valvetrain DOHC
Compression ratio 10.4:1
Combustion
Fuel system EFI
Fuel typePetrol (gasoline)
Output
Power output 177 hp (132 kW)
Torque output 173 lb⋅ft (235 N⋅m) [12]

A 2.5 L version of the AR family, first released in the RAV4 in China in 2013. [13]

Applications:

6AR-FSE

The 6AR-FSE is a 4-cylinder, 1998 cc, twincam, petrol engine equipped with D4-S direct fuel injection and VVT-iW. It can work in the Otto cycle and a modified-Atkinson cycle depending on output power. It was first introduced in the Camry in December 2014 for the Chinese market and March 2015 for the Thai market. The output of 6AR-FSE is 123 kW (165 bhp) at 6500 RPM and 199 N⋅m (147 lbf⋅ft) at 4600 RPM. [14] The stroke and bore are 86 mm × 86 mm (3.4 in × 3.4 in).

Applications:

6AR-FBS

The 6AR-FBS is a 4-cylinder, 1998 cc, twincam, petrol engine equipped with D4-S direct fuel injection and VVT-iW. It can work in the Otto cycle and a modified-Atkinson cycle depending on output power. It was first introduced in the Camry in October 2018 for the Thai market. The output is 167 PS (123 kW; 165 bhp) at 6500 RPM and 199 N⋅m (147 lbf⋅ft) at 4600 RPM. [16]

Applications:

8AR-FTS

8AR-FTS 2018 Toyota Crown 8AR-FTS.jpg
8AR-FTS

A 2.0 L turbocharged direct-injected member of the AR family, fitted with VVT-iW it is able to operate in both the Otto and a modified-Atkinson cycle. Debuted in the Lexus NX200t. [17] Power output in the 2015 NX200t is 175 kW (235 hp) at 4,800 - 5,600 rpm and 350 N⋅m (258 lb⋅ft) at 1,650 - 4000 rpm. The 8AR-FTS engine has Lexus’ ESTEC D-4ST (Economy with Superior Thermal Efficient Combustion Direct injection 4-stroke with Turbo) fuel injection. With separate twin injectors for both direct and port injection, ESTEC D-4ST could perform high-pressure direct injection into the cylinder and conventional intake port injection, or direct cylinder injection only, according to engine speed. [18] Power output in some applications, e.g. Lexus IS 200t XE30, Lexus GS 200t and Lexus RC 200t is bumped up by 5 kW (6.7 hp) up to 180 kW (242 hp) in the same rev range but torque remains the same. [18]

Applications:

Production

In Japan built by Toyota Motor Corporation in Kamigo Plant and by Toyota Industries Corporation. [24] [25] Toyota Motor Manufacturing Alabama, Inc. (TMMAL) started building the AR 2.5L and 2.7L engines beginning in mid-2011. [26]

GAC Toyota Engine Co., Ltd Guangqi, China, announced start of AR 2.5L and 2.7L engine production November 2011 [27]

Toyota Australia officially opened its new engine plant producing both petrol and hybrid engine variants in Melbourne. [28]

See also

Related Research Articles

<span class="mw-page-title-main">Toyota JZ engine</span> Reciprocating internal combustion engine

The Toyota JZ engine family is a series of inline-6 automobile engines produced by Toyota. As a replacement for the M-series inline-6 engines, the JZ engines were 24-valve DOHC engines in 2.5- and 3.0-litre versions.

<span class="mw-page-title-main">Toyota NZ engine</span> Reciprocating internal combustion engine

The Toyota NZ engine family is a straight-4 piston engine series. The 1NZ series uses aluminum engine blocks and DOHC cylinder heads. It also uses sequential fuel injection, and has 4 valves per cylinder with VVT-i.

<span class="mw-page-title-main">Toyota ZZ engine</span> Type of engine created by Toyota

The Toyota ZZ engine family is a straight-4 piston engine series. The ZZ series uses a die-cast aluminium engine block with thin press-fit cast iron cylinder liners, and aluminium DOHC 4-valve cylinder heads. The camshafts are chain-driven. The two 1.8 L members of the family, the 1ZZ and 2ZZ, use different bore and stroke. The former was optimised for economy, with torque emphasised in lower revolutions per minute operating range, while the latter is a "square" design optimised for high-RPM torque, yielding higher peak power. The ZZ family replaced the extremely popular cast-iron block 4A engines.

<span class="mw-page-title-main">Toyota AZ engine</span> Reciprocating internal combustion engine

The Toyota AZ engine family is a straight-4 piston engine series. The AZ series uses an aluminium engine block with cast iron cylinder liners and aluminium DOHC cylinder head. The engine series features many advanced technologies including slant-squish combustion chambers, offset cylinder and crank centers, and the VVT-i continuously variable intake valve timing system. The aluminium engine measures 626 mm (24.6 in) long, 608 mm (23.9 in) wide, and 681 mm (26.8 in) tall.

<span class="mw-page-title-main">Toyota MZ engine</span> Reciprocating internal combustion engine

The Toyota MZ engine family is a piston V6 engine series. The MZ series has an aluminium engine block and aluminium alloy DOHC cylinder heads. The cylinders are lined with cast iron, and is of a closed deck design. The engine is a 60 degree V6 design. It uses multi-port fuel injection (MFI), four valves per cylinder, a one-piece cast camshaft and a cast aluminium intake manifold. The MZ family is a lightweight V6 engine of an all-aluminium design, using lighter weight parts than the heavier duty VZ block engines in an effort to lower production costs, decrease engine weight, and decrease reciprocating weight without sacrificing reliability. Toyota sought to enhance the drivability pattern of the engine at exactly 3000 rpm, since that was the typical engine speed for motors cruising on the highway. The result was less cylinder distortion coupled with the decreased weight of rotating assemblies, smoother operation at that engine speed, and increased engine efficiency.

<span class="mw-page-title-main">Toyota VZ engine</span> Reciprocating internal combustion engine

The Toyota VZ engine family is a series of V6 gasoline piston engines ranging from 2.0 to 3.4 L in displacement and both SOHC and DOHC configurations. It was Toyota's first V6 engine, being made as a response to Nissan’s VG engine, one of Japan's first mass-produced V6 engines.

<span class="mw-page-title-main">Toyota UZ engine</span> Reciprocating internal combustion engine

The Toyota UZ engine family is a gasoline fueled 32-valve quad-camshaft V8 piston engine series used in Toyota's luxury offerings and sport utility vehicles. Three variants have been produced: the 1UZ-FE, 2UZ-FE, and 3UZ-FE. Production spanned 24 years, from 1989 to mid 2013, ending with the final production of the 3UZ-FE-powered Toyota Crown Majesta I-FOUR. Toyota's UZ engine family was replaced by the UR engine family.

<span class="mw-page-title-main">Toyota G engine</span> Reciprocating internal combustion engine

The Toyota Motor Corporation G-family engine is a family of straight-6 piston engines produced from 1979 to 2008. It is notable in that only a single displacement, 2.0 L (1,988 cc), was produced in this series. Initially belt-driven OHC non-interference engines, multivalve DOHC and variable valve timing were added later during the production run. The 1G-GEU was Toyota's first mass produced four-valve twincam engine. A prototype version of the 1G-GEU called the LASREα–X, featuring twin-turbos, variable valve timing and intake as well as variable displacement, was fitted to the Toyota FX-1 show car at the 1983 Tokyo Motor Show. It showcased a number of technologies which were later to become commonplace. This engine was designed around the new LASRE technology for lighter weight – such as sintered hollow camshafts. These engines were used as a lower-displacement alternative to the more upmarket M family and JZ family straight-sixes.

<span class="mw-page-title-main">Toyota GR engine</span> Reciprocating internal combustion engine

The Toyota GR engine family is a gasoline, open-deck, piston V6 engine series. The GR series has a 60° die-cast aluminium block and aluminium DOHC cylinder heads. This engine series also features 4 valves per cylinder, forged steel connecting rods and crankshaft, one-piece cast camshafts, a timing chain, and a cast aluminium lower intake manifold. Some variants use multi-port fuel injection, some have D4 direct injection, and others have a combination of direct injection and multi-port fuel injection or D4-S.

<span class="mw-page-title-main">Toyota S engine</span> Reciprocating internal combustion engine

The Toyota S Series engines are a family of straight-four petrol engines with displacements between 1.8 and 2.2 litres, produced by Toyota Motor Corporation from January 1980 to August 2007. The S series has cast iron engine blocks and aluminium cylinder heads. This engine was designed around the new LASRE technology for lighter weight – such as sintered hollow camshafts.

<span class="mw-page-title-main">Nissan HR engine</span> Reciprocating internal combustion engine

The HR is a family of straight-3 12-valve and straight-4 16-valve automobile engines with continuously variable valve timing, involving development by Nissan and/or Renault, and also Mercedes-Benz in the case of the H5Ht/M282. The designation of H engine is used by Renault, and M28x by Mercedes-Benz, to classify the family. There are three basic specifications of engine involving variations in engine architecture, or all-new architecture, with 72.2 mm (2.84 in), 75.5 mm (2.97 in) and 78 mm (3.07 in) bore diameter.

<span class="mw-page-title-main">Toyota UR engine</span> Type of engine made by Toyota

The Toyota UR engine family is a 32-valve dual overhead camshaft V8 piston engine series which was first introduced in 2006, as the UZ series it replaced began phasing out. Production started with the 1UR-FSE engine with D-4S direct injection for the 2007 Lexus LS. The series launched with a die-cast aluminum engine block, aluminum cylinder heads and magnesium cylinder head covers. All UR engines feature variable valve timing for both intake and exhaust cams or Dual VVT-i. Timing chains are used to drive the camshafts. The UR engine has been produced in 4.6, 5.0, and 5.7-liter displacement versions.

<span class="mw-page-title-main">Toyota ZR engine</span> Type of engine created by Toyota

The ZR engine is a family of straight-four 16-valve all-aluminum and water cooled gasoline engines with a die-cast aluminum block and variable valve timing developed by Toyota Motor Corporation, produced from 2007. Engines displace from 1.6 to 2.0 liters. Most engines in this family are equipped with Toyota's dual VVT-i technology that optimizes both intake and exhaust valve timing. This engine family is also the first to use Toyota's Valvematic system, first appearing on the Noah and Voxy in 2007 and then the European Avensis in 2009.

<span class="mw-page-title-main">Suzuki M engine</span> Reciprocating internal combustion engine

The Suzuki M engine family is a line of automobile engines from Suzuki. Ranging in displacement from 1.3 L to 1.8 L, it is a modern engine line with dual overhead cams, 16 valves, and multi-point fuel injection (MPFI). Fully developed in-house following Suzuki's separation from General Motors, the M engine replaced the long-lived G engine family.

<span class="mw-page-title-main">Toyota AD engine</span> Reciprocating internal combustion engine

The Toyota AD engine family is a series of 16 valve DOHC inline-4 turbo diesel diesel engines with electronic common rail direct injection using an aluminium cylinder head and an aluminium cylinder block with cast iron liners derived from the petrol Toyota AZ engine. The AD engine is offered in 2.0 and 2.2 liter versions. These engines are produced mainly for Europe, but few are exported to other areas such as India or New Zealand.

<span class="mw-page-title-main">Toyota SZ engine</span> Reciprocating internal combustion engine

The Toyota SZ engine family is a series of straight-4 piston engines with a forward-facing exhaust. Toyota Motor Manufacturing (UK) in Deeside produces SZ engines for the Yaris. All three types of the SZ engine are built in Tianjin FAW Toyota Engine Co., Ltd. (TFTE) Plant No. 1 in Xiqing District, Tianjin, China. The 2SZ-FE and 3SZ-FE variations are also manufactured by PT Astra Daihatsu Motor's Karawang Engine Plant in Indonesia.

<span class="mw-page-title-main">Toyota NR engine</span> Reciprocating internal combustion engine

The Toyota NR engine family is a series of small inline-four piston engines designed and manufactured by Toyota, with capacities between 1.2 and 1.5 litres.

<span class="mw-page-title-main">Lexus NX</span> Compact luxury crossover SUV

The Lexus NX is a compact luxury crossover SUV sold by Lexus, a luxury division of Toyota. Introduced in late 2014, it is positioned between the subcompact UX and the mid-size RX in Lexus’ crossover SUV lineup.

<span class="mw-page-title-main">Toyota Dynamic Force engine</span> Engine series from Toyota

The Dynamic Force engines are a family of internal combustion engines developed by Toyota under the brand's Toyota New Global Architecture (TNGA) strategy. The engines can be fueled by petrol (gasoline) or ethanol and can be combined with electric motors in a hybrid drivetrain. The engines were developed alongside the TNGA family of vehicle platforms, as part of a company-wide effort to simplify the vehicles being produced by Toyota.

<span class="mw-page-title-main">Suzuki K engine</span> Reciprocating internal combustion engine

The Suzuki K engine family is a series of automobile engines from Suzuki, introduced in 1994. Displacements range from 0.7 L to 1.5 L. All engines have aluminium cylinder blocks with three or four cylinders in-line. Cylinder heads have two overhead camshafts, driven by chain, and four valves per cylinder. Fuel is gasoline/petrol, metered by multipoint fuel injection or direct injection. Some variants are turbocharged.

References

  1. ↑ "2009 Venza Product Information" (Press release). USA: Toyota. 2008-11-03. Retrieved 2013-05-24.
  2. ↑ "2009 Highlander Product Information" (Press release). USA: Toyota. 2008-09-11. Retrieved 2013-05-24.
  3. ↑ "2009 RAV4 Product Information" (Press release). USA: Toyota. 2008-09-11. Retrieved 2013-05-24.
  4. ↑ Madelin, Jacqui (2012-02-26). "Camry: Toyota eyes fleet buyers". NZ Herald News. Retrieved 2013-05-24.
  5. ↑ "Toyota Camry homepage". Australia: Toyota. Retrieved 2013-05-24.
  6. ↑ "Camry - Are you an Executive of Life?". New Zealand: Toyota. Archived from the original on 2013-02-09. Retrieved 2013-05-24.
  7. ↑ "ข้อมูลทางเทคนิค - New Camry" [Technical - New Camry] (in Thai). Thailand: Toyota. Archived from the original on 2012-06-01. Retrieved 2013-05-24.
  8. ↑ "トヨタ ハリアー 主要諸元" [Toyota Harrier ー Main specifications](PDF) (in Japanese). Japan: Toyota. Retrieved 2020-03-28.
  9. ↑ "Toyota RAV4 Technical Specifications" (PDF) (Press release). UK: Toyota. Retrieved 2020-03-28.
  10. ↑ Lithgow, Ian. "2AR-FSE Lexus engine". australiancar.reviews. Retrieved 2015-08-28.
  11. ↑ "Lexus begins sales of new IS 300h hybrid in Japan along with new IS lineup". Green Car Congress. 2013-05-16. Retrieved 2015-05-03.
  12. ↑ "Toyota Global Site | Vehicle Gallery | Camry". Toyota. Retrieved 2017-11-16.
  13. ↑ "【图】途观/CR-V的天敌 抢先实拍全新国产RAV4_RAV4荣放_汽车之家" [[Figure] Tiguan / CR-V's natural enemies first shot real new domestic RAV4_RAV4 Rong _Car House] (in Chinese). China. 2013-08-26. Retrieved 2017-11-16.
  14. ↑ "New Camry" (PDF) (Brochure). Malaysia: Toyota. October 2015. Archived from the original (PDF) on 2016-03-04. Retrieved 2016-01-12.
  15. ↑ Lee, Jonathan (2015-04-20). "Shanghai 2015: Lexus ES facelift unveiled, new 2.0 mill". PaulTan.org. Retrieved 2015-04-21.
  16. ↑ Lye, Gerard (2018-10-30). "2018 Toyota Camry launched in Thailand - four variants, including hybrids; priced from 1.445 mil baht". paultan.org. Malaysia. Retrieved 2018-11-02.
  17. ↑ "LEXUS、コンパクトクロスオーバーSUV「NX」をワールドプレミア" [Lexus, world premiere of the compact crossover SUV "NX"] (Press release). Japan: Toyota. 2014-04-20. Retrieved 2014-06-22.
  18. 1 2 "8AR-FTS Toyota engine". australiancar.reviews. Retrieved 2016-07-02.
  19. ↑ Goreham, John (2014-08-01). "Upcoming Lexus IS 200t will be more than 1 second faster to 60 MPH". Torque News. United Kingdom. Retrieved 2015-04-16.
  20. ↑ "Mingling with the Classics: Lexus Introduces 2016 GS During Pebble Beach Concours Celebrations" (Press release). US: Toyota. 2015-08-13. Retrieved 2015-08-22.
  21. ↑ Tan, Paul (2015-04-20). "Shanghai 2015: Lexus RX 200t replaces the old RX 270". PaulTan.org. Malaysia. Retrieved 2015-04-20.
  22. ↑ Radu, Mihnea (2015-10-02). "Toyota Crown Gets 2-Liter Turbo Engine, Upgraded Suspension in Japan". www.autoevolution.com. Retrieved 2015-10-24.
  23. ↑ "Harrier equipped with Turbo Engine". Japan. 2017-07-20. Retrieved 2017-07-20.
  24. ↑ "General Status of Plants in Japan | Kamigo Plant" (Press release). Toyota. 2012. Retrieved 2013-05-25.
  25. ↑ "Engines for Passenger Cars". Japan: Toyota Industries. Retrieved 2013-05-25.
  26. ↑ "TMC's Alabama, U.S.A. Plant to Build 4-cylinder Engines" (Press release). Japan: Toyota. 2009-08-21. Retrieved 2013-05-25.
  27. ↑ 中国の広汽トヨタエンジン工場で新型エンジンの生産開始 [Start of production of the new Toyota engine, in Guangqi Toyota engine plant in China] (Press release) (in Japanese). Japan: Toyota. 2011-11-09. Retrieved 2013-05-25.
  28. ↑ "Toyota Unveils New Engine Plant". Australia: Toyota Australia. Retrieved 2013-08-16.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.