Multifuel

Last updated
Multifuel automobiles, from several manufacturers, popularly known as "flex" autos, that run on any blend of ethanol and gasoline. Four Brazilian full flex-fuel automoviles 05 2008.jpg
Multifuel automobiles, from several manufacturers, popularly known as "flex" autos, that run on any blend of ethanol and gasoline.

Multifuel, sometimes spelled multi-fuel, is any type of engine, boiler, or heater or other fuel-burning device which is designed to burn multiple types of fuels in its operation. One common application of multifuel technology is in military settings, where the normally-used diesel or gas turbine fuel might not be available during combat operations for vehicles or heating units. Multifuel engines and boilers have a long history, but the growing need to establish fuel sources other than petroleum for transportation, heating, and other uses has led to increased development of multifuel technology for non-military use as well, leading to many flexible-fuel vehicle designs in recent decades.

Contents

A multifuel engine is constructed so that its compression ratio permits firing the lowest octane fuel of the various accepted alternative fuels. A strengthening of the engine is necessary in order to meet these higher demands. [1] [ dubious – discuss ] Multifuel engines sometimes have switch settings that are set manually to take different octanes, or types, of fuel. [2]

Types

Multifuel systems can be classified by the fuel-burning appliance it is based on. For internal combustion engines there are:

For heaters, see multi-fuel stove.

Military multifuel engines

One common use of this technology is in military vehicles, so that they may run a wide range of alternative fuels such as gasoline or jet fuel. This is seen as desirable in a military setting as enemy action or unit isolation may limit the available fuel supply, and conversely enemy fuel sources, or civilian sources, may become available for usage. [3]

One large use of a military multi-fuel engine was the LD series used in the US M35 2+1⁄2-ton and M54 5-ton trucks built between 1963 and 1970. A military standard design using M.A.N. technology, it was able to use different fuels without preparation. [4] [5] Its primary fuel was Diesel #1, #2, or AP, but 70% to 90% of other fuels could be mixed with diesel, depending on how smooth the engine would run. Low octane commercial and aviation gasoline could be used if engine oil was added, jet fuel Jet A, B, JP-4, 5, 7, and 8 could be used, as well as fuel oil #1 and #2. [6] In practice, they only used diesel fuel, their tactical advantage was never needed, and in time they were replaced with commercial diesel engines. Another use of multifuel engines is the American M1 Abrams Main battle tank, which uses a multifuel gas turbine engine.

Currently, a wide range of Russian military vehicles employ multifuel engines, such as the T-72 tank (multifuel diesel) and the T-80 (multifuel gas turbine).

Non-military usage

Many other types of engines and other heat-generating machinery are designed to burn more than one type of fuel. For instance, some heaters and boilers designed for home use can burn wood, pellets, and other fuel sources. These offer fuel flexibility and security, but are more expensive than are standard single fuel engines. [7] Portable stoves are sometimes designed with multifuel functionality, in order to burn whatever fuel is found during an outing. [8] Innovative industrial heaters or burners were the subject of multi-fuel research at a Shell plant in 2014. [9]

The movement to establish alternatives to automobiles running solely on gasoline has greatly increased the number of automobiles available which use multifuel engines, such vehicles generally being termed a bi-fuel vehicle or flexible-fuel vehicle.

Underperformance issues

Multifuel engines are not necessarily underpowered, but in practice some engines have had issues with power due to design compromises necessary to burn multiple types of fuel in the same engine. Perhaps the most notorious example from a military perspective is the L60 engine used by the British Chieftain Main Battle Tank, which resulted in a very sluggish performance -- in fact, the Mark I Chieftain (used only for training and similar activities) was so underpowered that some were incapable of mounting a tank transporter. An equally serious issue was that changing from one fuel to another often required hours of preparation. [10]

The US LD series had a power output comparable to commercial diesels of the time. It was underpowered for the 5-ton trucks, but that was due the engine size itself; the replacement diesel was much larger and more powerful. The LD engines did burn diesel fuel poorly and were very smokey. The final LDT-465 model received a turbocharger largely to clean up the exhaust, there was little power increase. [11]

See also

Footnotes

  1. ↑ Taylor, CF. (1985), The Internal-combustion Engine in Theory and Practice. p. 166.
  2. ↑ Dunstan, S., Chieftain Main Battle Tank. p. 8
  3. ↑ Dunstan, S., Chieftain. p. 8
  4. ↑ Crismon (2001), pp. 339, 356
  5. ↑ Doyle (2003), pp.128-129, 181-182
  6. ↑ TM 9-2320-209-10-1 pp. 1-20 to 1-23
  7. ↑ See, for example, Pahl, G., Natural Home Heating: The Complete Guide to Renewable Energy, p. 145, 203.
  8. ↑ See, for example, Jacobson, C., Expedition Canoeing: A Guide To Canoeing Wild Rivers In North America, p. 131.
  9. ↑ Benson, Charles, and Wilson, Robert. Fuel-Flexible Combustion System for Refinery and Chemical Plant Process Heaters. United States: N. p., 2014. Web. doi:10.2172/1170362. Retrieved 30 October 2023.
  10. ↑ Dunstan, Chieftain, p. 13
  11. ↑ Doyle (2003), pp. 128

Related Research Articles

Kerosene, or paraffin, is a combustible hydrocarbon liquid which is derived from petroleum. It is widely used as a fuel in aviation as well as households. Its name derives from Greek: κηρός (keros) meaning "wax", and was registered as a trademark by Canadian geologist and inventor Abraham Gesner in 1854 before evolving into a generic trademark. It is sometimes spelled kerosine in scientific and industrial usage.

<span class="mw-page-title-main">Diesel fuel</span> Liquid fuel used in diesel engines

Diesel fuel, also called diesel oil or historically heavy oil, is any liquid fuel specifically designed for use in a diesel engine, a type of internal combustion engine in which fuel ignition takes place without a spark as a result of compression of the inlet air and then injection of fuel. Therefore, diesel fuel needs good compression ignition characteristics.

A stratified charge engine describes a certain type of internal combustion engine, usually spark ignition (SI) engine that can be used in trucks, automobiles, portable and stationary equipment. The term "stratified charge" refers to the working fluids and fuel vapors entering the cylinder. Usually the fuel is injected into the cylinder or enters as a fuel rich vapor where a spark or other means are used to initiate ignition where the fuel rich zone interacts with the air to promote complete combustion. A stratified charge can allow for slightly higher compression ratios without "knock," and leaner air/fuel ratio than in conventional internal combustion engines.

<span class="mw-page-title-main">Liquid fuel</span> Liquids that can be used to create energy

Liquid fuels are combustible or energy-generating molecules that can be harnessed to create mechanical energy, usually producing kinetic energy; they also must take the shape of their container. It is the fumes of liquid fuels that are flammable instead of the fluid. Most liquid fuels in widespread use are derived from fossil fuels; however, there are several types, such as hydrogen fuel, ethanol, and biodiesel, which are also categorized as a liquid fuel. Many liquid fuels play a primary role in transportation and the economy.

<span class="mw-page-title-main">Block heater</span> Heating system for internal combustion engines to assist in starting in cold weather.

A block heater is used in cold climates to warm an engine prior to starting. They are mostly used for car engines; however, they have also been used in aircraft engines.

Vegetable oil can be used as an alternative fuel in diesel engines and in heating oil burners. When vegetable oil is used directly as a fuel, in either modified or unmodified equipment, it is referred to as straight vegetable oil (SVO) or pure plant oil (PPO). Conventional diesel engines can be modified to help ensure that the viscosity of the vegetable oil is low enough to allow proper atomization of the fuel. This prevents incomplete combustion, which would damage the engine by causing a build-up of carbon. Straight vegetable oil can also be blended with conventional diesel or processed into biodiesel, HVO or bioliquids for use under a wider range of conditions.

<span class="mw-page-title-main">Thermal efficiency</span> Performance measure of a device that uses thermal energy

In thermodynamics, the thermal efficiency is a dimensionless performance measure of a device that uses thermal energy, such as an internal combustion engine, steam turbine, steam engine, boiler, furnace, refrigerator, ACs etc.

<span class="mw-page-title-main">Masonry heater</span> Heating device

A masonry heater is a device for warming an interior space through radiant heating, by capturing the heat from periodic burning of fuel, and then radiating the heat at a fairly constant temperature for a long period. Masonry heaters covered in tile are called cocklestoves. The technology has existed in different forms, from back into the Neoglacial and Neolithic periods. Archaeological digs have revealed excavations of ancient inhabitants utilizing hot smoke from fires in their subterranean dwellings, to radiate into the living spaces. These early forms have evolved into modern systems.

<span class="mw-page-title-main">Steam generator (railroad)</span>

A steam generator is a type of boiler used to produce steam for climate control and potable water heating in railroad passenger cars. The output of a railroad steam generator is low pressure, saturated steam that is passed through a system of pipes and conduits throughout the length of the train.

Engine efficiency of thermal engines is the relationship between the total energy contained in the fuel, and the amount of energy used to perform useful work. There are two classifications of thermal engines-

  1. Internal combustion and
  2. External combustion engines.
<span class="mw-page-title-main">M35 series 2½-ton 6×6 cargo truck</span> US military truck

The M35 2½-ton cargo truck is a long-lived 2½-ton 6×6 cargo truck initially used by the United States Army and subsequently utilized by many nations around the world. Over time it evolved into a family of specialized vehicles. It inherited the nickname "Deuce and a Half" from an older 2½-ton truck, the World War II GMC CCKW.

<span class="mw-page-title-main">Alternative fuel vehicle</span> Type of vehicle

An alternative fuel vehicle is a motor vehicle that runs on alternative fuel rather than traditional petroleum fuels. The term also refers to any technology powering an engine that does not solely involve petroleum. Because of a combination of factors, such as environmental and health concerns including climate change and air pollution, high oil-prices and the potential for peak oil, development of cleaner alternative fuels and advanced power systems for vehicles has become a high priority for many governments and vehicle manufacturers around the world.

<span class="mw-page-title-main">Bi-fuel vehicle</span> Vehicle capable of running on two fuels

Bi-fuel vehicles are vehicles with multifuel engines capable of running on two fuels. The two fuels are stored in separate tanks and the engine is able to run on one fuel at a time. On internal combustion engines, a bi-fuel engine typically burns gasoline and a volatile alternate fuel such as natural gas (CNG), LPG, or hydrogen. Bi-fuel vehicles have the capability to switch back and forth from the gasoline to the other fuel, manually or automatically. A related concept is the duel-fuel vehicle which must burn both fuels in combination. Diesel engines converted to use gaseous fuels fall into this class due to the different ignition system.

<span class="mw-page-title-main">Multi-fuel stove</span>

A multi-fuel stove is similar to a wood-burning stove in appearance and design. Multifuel refers to the capability of the stove to burn wood and also coal, wood pellets, or peat. Stoves that have a grate for the fire to burn on and a removable ash pan are generally considered multi-fuel stoves. If the fire simply burns on a bed of ash, it is a wood-only fuelled appliance, and cannot be used for coal or peat.

Internal combustion engines come in a wide variety of types, but have certain family resemblances, and thus share many common types of components.

<span class="mw-page-title-main">Internal combustion engine</span> Engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber

An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.

Pellet heating is a heating system in which wood pellets are combusted. Other pelletized fuels such as straw pellets are used occasionally. Today's central heating system which run on wood pellets as a renewable energy source are comparable in operation and maintenance of oil and gas heating systems.

<span class="mw-page-title-main">Pellet boiler</span> Heating system

A pellet boiler is a heating system that burns wood pellets. Pellet boilers are used in central heating systems for heat requirements from 3.9 kW (kilowatt) to 1 MW (megawatt) or more. Pellet central heating systems are used in single family homes, and in larger residential, commercial, or institutional applications. Pellet boiler systems run most efficiently at full load and can usually be regulated down to 30% of full load. Since the warm up phase of pellet boilers usually takes longer than for oil or gas firing systems, short burning phases have negative effects on the fuel efficiency. In order to improve energy efficiency and reduce harmful emissions, pellet boilers are usually combined with buffer systems, such as insulated water tanks.

<span class="mw-page-title-main">Mack Trucks in military service</span>

Mack Trucks has been selling heavy duty trucks and buses to the United States military since 1911. Virtually every model has been used. The majority have been commercial models designed and built by Mack with their own components, but they have also designed and built military specification tactical trucks. The military vehicles are rated by payload measured in tons.

<span class="mw-page-title-main">5-ton 6×6 truck</span>

The 5‑ton 6x6 truck, officially "Truck, 5-ton, 6x6", was a class of heavy-duty six-wheel drive trucks used by the US Armed Forces. The basic cargo version was designed to transport a 5-ton (4,500 kg) load over all roads and cross-country terrain in all weather. Through three evolutionary series there have been component improvements, but all trucks were mechanically very similar. They were the standard heavy-duty truck of the US military for 40 years, until replaced by the Medium Tactical Vehicle (MTV) beginning in 1991.

References

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.