Great Dunmow Mill | |
---|---|
![]() | |
Origin | |
Mill name | Church End Mill |
Mill location | TL 633 226 |
Coordinates | 51°52′37″N0°22′26″E / 51.877°N 0.374°E Coordinates: 51°52′37″N0°22′26″E / 51.877°N 0.374°E |
Operator(s) | Private |
Year built | 1822 |
Information | |
Purpose | Corn mill |
Type | Tower mill |
Storeys | Four storeys |
No. of sails | Four sails |
Type of sails | Patent sails |
Windshaft | Cast iron |
Winding | Fantail |
Auxiliary power | Steam engine |
No. of pairs of millstones | Two pairs, plus a third pair driven by auxiliary power |
Church End Mill is a grade II listed [1] Tower mill at Great Dunmow, Essex, England which has been converted to residential use.
Church End Mill was built by William Redington, a miller from Harlow in 1822 for John Fuller. It incorporated second-hand machinery from a smock mill from an unknown location and the total cost of the mill was £564 10s 6d. In 1840, a new cast iron windshaft and Patent sails were fitted, [2] but the windshaft snapped during a gale on 13 November, less than three months after it had been fitted. [3] The sails landed on the outbuildings connected with the mill. The mill remained in the ownership of John Fuller until his death in 1887. The mill did little trade after 1894, and ceased work c1902, the sails being removed then. By 1907 it was being used as a studio and during World War II was used as an observation post, the cap having been removed by then. A new cap was fitted in 1974 by millwright Philip Barrett-Lennard. The mill has been house converted, with no machinery remaining inside. [2]
Church End Mill is a four-storey tower mill with a conical cap with a ball finial. The mill had four single Patent sails carried on a cast-iron windshaft and was winded by a six-bladed fantail. The tower is 40 feet (12.19 m) high to curb level, 20 feet (6.10 m) diameter at base level and 10 feet (3.05 m) diameter at the curb. [2] The brickwork is 2 feet 3 inches (690 mm) thick at base level. There was a stage at first-floor level. [4] Two pairs of French Burr millstones were driven by wind, with a third pair by steam engine towards the end of the mill’s working life. [2]
As originally built, the mill had an oak windshaft, 23 inches (580 mm) square at the poll end and 14 feet 6 inches (4.42 m) long carrying four Common sails with cloths 30 feet (9.14 m) long by 4 feet 6 inches (1.37 m) wide. The windshaft carried an elm brake wheel 9 feet (2.74 m) diameter with 80 cogs, which drove an elm wallower 4 feet 8 inches (1.42 m) diameter with 46 cogs, carried on an oak upright shaft 21 feet 6 inches (6.55 m) long and 15 inches (380 mm) square. The clasp arm elm great spur wheel was 8 feet (2.44 m) diameter, with 105 cogs. It drove two elm stone nuts of 28 inches (710 mm) diameter, each having 28 cogs. [4]
References for above:- [2]
Upminster Windmill is a Grade II* listed smock mill located in Upminster in the London Borough of Havering, England. It was formerly known as Abraham's Mill and was in Essex when built. It has been restored and is a museum open to the public at selected times.
Outwood Windmill is a Grade I listed post mill in Outwood, Surrey. Built in 1665 by Thomas Budgen, a miller from Nutfield in Surrey, it is Britain's oldest working windmill.
John Webb’s or Lowe’s Mill is a Grade II* listed tower mill at Thaxted, Essex, England, which had been restored to working order, but is currently out of action following the loss of a sail in April 2010.
Shirley Windmill is a Grade II listed tower mill in Shirley, in the London Borough of Croydon, England which has been restored to working order.
Shiremark Mill, also known as Kingsfold Mill or Capel Mill was a listed Smock mill at Capel, Surrey, England, which was burnt down in 1972.
Aythorpe Roding Windmill is a Grade II* listed Post mill at Aythorpe Roding, Essex, England which has been restored to working order.
Bocking Windmill or Bocking Churchstreet Windmill is a grade I listed post mill at Bocking, Essex, England which has been restored.
Fryerning Mill is a grade II* listed post mill at Mill Green, Fryerning, Essex, which has been restored.
Mountnessing Windmill is a grade II* listed post mill at Mountnessing, Essex, England. Built in 1807, it was most recently restored to working order in 1983.
Ramsey Windmill is a grade II* listed post mill at Ramsey, Essex, England which has been restored.
Baker Street Mill is a grade II listed smock mill at Baker Street, Orsett, Essex, England which has been part adapted to residential use on its lower two floors only.
Terling Windmill is a grade II listed Smock mill at Terling, Essex, England, which has been converted to residential use.
South Ockendon Windmill was a Smock mill at South Ockendon, Essex, England which collapsed on 2 November 1977.
Gibraltar Mill is a grade II listed Tower mill at Great Bardfield, Essex, England which has been converted to residential use.
Rayleigh Windmill is a grade II listed Tower mill at Rayleigh, Essex, England which has been restored as a landmark and is used as a museum.
Stansted Mountfitchet Windmill is a grade II* listed Tower mill at Stansted Mountfitchet, Essex, England which is also a Scheduled Ancient Monument. It has been restored and can turn by wind.
Stock Windmill is a grade II* listed tower mill at Stock, Essex, which has been restored.
Messing Maypole Mill is a grade II listed Tower mill at Tiptree, Essex, England which has been converted to a residence. Prior to boundary changes made when the civil parish of Tiptree was established in 1934, the mill was in the parish of Tolleshunt Knights.
Gainsford End Mill is a grade II listed tower mill at Gainsford End, near Toppesfield, Essex, England, which has been converted to a residence.
White Roding Windmill is a Grade II listed preserved tower mill at White Roding, Essex, England.