A 44-ton 1-B-1 experimental gas turbine locomotive designed by R. Tom Sawyer and built in 1952 for testing by the U.S. Army Transportation CorpsUP 18, a gas turbine-electric locomotive preserved at the Illinois Railway Museum
A gas turbine locomotive is a type of railwaylocomotive in which the prime mover is a gas turbine. Several types of gas turbine locomotive have been developed, differing mainly in the means by which mechanical power is conveyed to the driving wheels (drivers). A gas turbine train typically consists of two power cars (one at each end of the train), and one or more intermediate passenger cars.
A gas turbine offers some advantages over a piston engine. There are few moving parts, decreasing the need for lubrication and potentially reducing maintenance costs, and the power-to-weight ratio is much higher. A turbine of a given power output is also physically smaller than an equally powerful piston engine, so that a locomotive can be extremely powerful without needing to be inordinately large.
However, a gas turbine's power output and efficiency both drop dramatically with rotational speed, unlike a piston engine, which has a comparatively flat power curve. This makes GTEL systems useful primarily for long-distance high-speed runs. Additional problems with gas turbine-electric locomotives include the fact that they are very noisy[1][2] and produce such extremely hot exhaust gasses that, if the locomotive were parked under an overpass paved with asphalt, it could melt the asphalt.[3]
Early developments
A gas turbine locomotive was patented in 1861 by Marc Antoine Francois Mennons (British patent no. 1633).[4] The drawings in Mennons' patent show a locomotive of 0-4-2 wheel arrangement with a cylindrical casing resembling a boiler. At the front of the casing is the compressor, which Mennons calls a ventilator. This supplies air to a firebox and the hot gases from the firebox drive a turbine at the back of the casing. The exhaust from the turbine then travels forwards through ducts to preheat the incoming air. The turbine drives the compressor through gearing and an external shaft. There is additional gearing to a jackshaft which drives the wheels through side rods. The fuel is solid (presumably coal, coke or wood) and there is a fuel bunker at the rear. There is no evidence that the locomotive was actually built but the design includes the essential features of gas turbine locomotives built in the 20th century, including compressor, combustion chamber, turbine and air pre-heater.
Work leading to the emergence of the gas turbine locomotive began in France and Sweden in the 1920s but the first locomotive did not appear until the 1940s. High fuel consumption was a major factor in the decline of conventional gas-turbine locomotives and the use of a piston engine as a gas generator would probably give better fuel economy than a turbine-type compressor, especially when running at less than full load.
One option is a two-shaft machine, with separate turbines to drive the compressor and the output shaft. Another is to use a separate gas generator, which may be of either rotary or piston type.
Gas turbine-mechanical
Gas turbine-mechanical locomotives use a mechanical transmission to deliver the power output of gas turbines to the wheels. Owing to the difference in their speeds, this is technically challenging and so a mechanical transmission did not appear until ten years after the first electric transmissions.
France
Diagram of a free-piston engine as a gas generator for a gas turbine
The first gas turbine-mechanical locomotive in the world, Class 040-GA-1 of 1,000hp (0.75MW) was built by Renault in 1952 and had a Pescarafree-piston engine as a gas generator. It was followed by two further locomotives, Class 060-GA-1 of 2,400hp (1.8MW) in 1959–61.[5]
The Pescara gas generator in 040-GA-1 consisted of a horizontal, single cylinder, two-strokediesel engine with opposed pistons. It had no crankshaft and the pistons were returned after each power stroke by compression and expansion of air in a separate cylinder. The exhaust from the diesel engine powered the gas-turbine which drove the wheels through a two-speed gearbox and propeller shafts.[6]:142–3 The free-piston engine was patented in 1934 by Raul Pateras Pescara.
The power gas locomotive was built by Gotaverken. It had a vertical, five cylinder, two-stroke diesel engine with opposed pistons. There was a single crankshaft connected to both upper and lower pistons. The exhaust from the diesel engine powered the gas turbine which drove the wheels through reduction gearing, jack shaft and side rods.
Czechoslovakia
Turbine power was considered for railway traction in the former Czechoslovakia. Two turbine-powered prototypes were built, designated TL 659.001 and TL 659.002, featuring C-C wheel arrangement, 3,200hp (2.4MW) main turbine, helper turbine and Tatra 111 helper diesel engine.
The first prototype (TL 659.001) was finished in February 1958 and was scheduled to be exhibited at Expo '58. However, this was aborted because it was not ready in time. The first out-of-factory tests were conducted in March 1959 on the Plzeň–Cheb–Sokolov line. On 15May 1959, the first prototype pulled its heaviest train, 6,486t (7,150 short tons), but the turbine caught fire only a day later. The engine was never restored and eventually scrapped.
The second prototype (TL 659.002) was built with lessons learned from the first. It left the factory in March 1960 and was the only turbine locomotive to pass the tests for regular service on tracks of the former Czechoslovak State Railways. It was tried near Kolín and Plzeň with mixed results. This engine was taken out of service in April 1966 and sold to the University of Žilina as an educational instrument. It was scrapped some time later.
Although the experiments had mixed results, these were the most powerful locomotives with a purely mechanical powertrain in the world and also the most powerful independent-traction locomotives in Czechoslovakia.
United Kingdom
The British Rail GT3 was a simple machine consisting essentially of a standard oil-fired gas turbine mounted on a standard steam locomotive chassis, built as a demonstrator by English Electric in 1961. Its almost crude simplicity enabled it to avoid much of the unreliability which had plagued the complex experimental GTELs18000 and 18100 in earlier years, but it failed to be competitive against conventional traction and was scrapped.
A gas turbine-electric locomotive (GTEL) is a locomotive that uses a gas turbine to drive an electric generator or alternator, producing an electric current which is used to power traction motors. This type of locomotive was first experimented with during the Second World War, but reached its peak in the 1950s to 1960s. Few locomotives use this system today.
A GTEL uses a turbo-electric drivetrain in which a turboshaft engine drives the electric generator or alternator via a system of gears. The electric current is distributed to power the traction motors that drive the locomotive. In overall terms the system is very similar to a conventional diesel-electric, with the large diesel engine replaced with a smaller gas turbine of similar power.
Union Pacific operated the largest fleet of such locomotives of any railroad in the world, and was the only railroad to use them for hauling freight. Most other GTELs have been built for small passenger trains, and only a few have seen any real success in that role. With a rise in fuel costs (eventually leading to the 1973 oil crisis), gas turbine locomotives became uneconomical to operate, and many were taken out of service. Union Pacific's locomotives also required more maintenance than originally anticipated, due to fouling of the turbine blades by the Bunker Coil used as fuel.
In 1939, the Swiss Federal Railways ordered a GTEL with a 1,620kW (2,170hp) of maximum engine power from Brown Boveri. It was completed in 1941, and then underwent testing before entering regular service. The Am 4/6 was the world's first gas turbine-electric locomotive. It was intended primarily to work light, fast, passenger trains on routes that normally handle insufficient traffic to justify electrification.
Two gas turbine locomotives of different design, 18000 and 18100, were ordered by the Great Western Railway (GWR) but completed for the newly nationalised British Railways.
British Rail 18000 was built by Brown Boveri and delivered in 1949.[7] It was a 1840kW (2470hp) GTEL, ordered by the GWR and used for express passenger services.
British Rail 18100 was built by Metropolitan-Vickers and delivered in 1951. It had an aircraft-type gas turbine of 2.2MW (3,000hp). Its maximum speed was 90 miles per hour (140km/h).[8]
A third locomotive, the GT3, was constructed in 1961. Although built by English Electric, who had pioneered electric transmission with LMS 10000 locomotives, this used a turbine-mechanical transmission.[9]
The British Rail APT-E, the prototype of the Advanced Passenger Train, was turbine-powered. Like the French TGV, later models used an alternative electric powertrain. This choice was made because British Leyland, the turbine supplier, ceased production of the model used in the APT-E, having lost interest in gas turbine technology following the 1970s oil crisis.[10]
United States
First generation GTEL and a 1923 electric auto in Fremont, Nebraska in 1953
ALCO-GE built a prototype oil-fired gas turbine-electric locomotive in 1948, with a B-B-B-Bwheel arrangement. After demonstration runs it was acquired by Union Pacific, who were seeking a more powerful alternative to diesel for transcontinental trains.[11]
UP ran a fleet of 55 turbine-powered freight locomotives starting in the early 1950s, all produced by Alco-GE. The first- and second-generation versions shared the same wheel arrangement as the prototype; the third-generation version were C-C types. All were widely used on long-haul routes, and were cost-effective despite their poor fuel economy, due to their use of "leftover" fuels from the petroleum industry. At their height the railroad estimated that they powered about 10% of Union Pacific's freight trains, a much wider use than any other example of this class. As other uses were found for these heavier petroleum byproducts, notably for plastics, the cost of the Bunker C fuel increased until the units became too expensive to operate and they were retired from service by 1969.
In April 1950, Baldwin and Westinghouse completed an experimental 4,000hp (3,000kW) turbine locomotive, #4000, known as the Blue Goose, also using the B-B-B-B wheel arrangement. The locomotive used two 2,000hp (1,500kW) turbine engines, was equipped for passenger train heating with a steam generator that utilized the waste exhaust heat of the right hand turbine, and was geared for 100 miles per hour (160km/h). While it was demonstrated successfully in both freight and passenger service on the PRR, MKT, and CNW, no production orders followed, and it was scrapped in 1953.[12]
In the 1960s United Aircraft built the Turbo passenger train, which was tested by the Pennsylvania Railroad and later used by Amtrak and Via Rail. The Via remained in service into the 1980s and had an excellent maintenance record during this period, but was eventually replaced by the LRC in 1982. Amtrak purchased two different types of turbine-powered trainsets, which were both called Turboliners. The sets of the first type were similar in appearance to SNCF's T 2000 Turbotrain, though compliance with FRA safety regulations made them heavier and slower than the French trains. None of the first-type Turboliners remain in service. Amtrak also added a number of similarly named Rohr Turboliners (or RTL) to its roster. There were plans to rebuild these as RTL IIIs, but this program was cancelled. The units owned by New York State were sold for scrap and the three remaining RTL trainsets are stored at North Brunswick, New Jersey and New Haven, Connecticut.[13]
In 1966, the Long Island Rail Road tested an experimental gas turbine railcar (numbered GT-1), powered by two Garrett turbine engines. This car was based on a BuddPioneer III design, with transmissions similar to Budd's 1950s-era RDCs. The car was later modified (as GT-2) to add the ability to run on electric third rail as well.[14][15]
In 1977, the LIRR tested eight more gas turbine-electric/electric dual mode railcars, in an experiment sponsored by the USDOT. Four of these cars had GE-designed powertrains, while the other four had powertrains designed by Garrett (four more cars had been ordered with GM/Allison powertrains, but were canceled). These cars were similar to LIRR's M1EMU cars in appearance, with the addition of step wells for loading from low level platforms. The cars suffered from poor fuel economy and mechanical problems, and were withdrawn from service after a short period of time. The four GE-powered cars were converted to M1 EMUs and the Garrett cars were scrapped.[16]
Bombardier's experimental JetTrain locomotive toured North America in an attempt to raise the technology's public profile in the early 2000s.
In 1997 the Federal Railroad Administration (FRA) solicited proposals to develop high speed locomotives for routes outside the Northeast Corridor where electrification was not economical. Bombardier Ltd, at the Plattsburg, N.Y. plant where the Acela was produced, developed a prototype (JetTrain) which combined a Pratt & Whitney Canada PW100 gas turbine and a diesel engine with a single gearbox powering four traction motors identical to those in Acela. The diesel provided head end power and low speed traction, with the turbine not being started until after leaving stations. The prototype was completed in June 2000, and safety testing was done at the FRA's Pueblo, CO test track beginning in the summer of 2001. A maximum speed of 156 miles per hour (251km/h) was reached. The prototype was then taken on a tour of potential sites for high speed service, but no service has yet begun.
Russia
Two gas turbine-electric locomotive types underwent testing in the Soviet Union. The test program began in 1959 and lasted into the early 1970s. The G1-01 freight GTEL, produced by Kolomna Locomotive Works, was intended to consist of two locomotives of a C-C wheel arrangement, but only one section was built. The GP1 passenger locomotive was a similar design with body of TEP60diesel locomotive, also with a C-C wheel arrangement, introduced to the test program in 1964. Two units were built by Kolomna Works, GP1-0001 and GP1-0002, which were also used in regular service with passenger trains. Both types had a maximum power output of 2,600kW (3,500hp).[17]
Another soviet gas turbine-hydraulic freight locomotive type GT101 was developed and produced in 1960 by Luhansk Locomotive Works. Like the G1 locomotive, it was intended to consist of two sections of a C-C wheel arrangement, but only one section was built. This section was equipped with four free piston gas generators and gas turbine with a maximum power output of 2,200kW (3,000hp), and a hydraulic transmission. Unlike other locomotives, it was not in regular service.[18]
In 2006, Russian Railways introduced the GEM-10 switcher GTEL. The turbine runs on liquefied natural gas (LNG) and has a maximum power output of 1,000kW (1,300hp). The GEM-10 has a C-C wheel arrangement. The TGEM10-0001, which uses the same turbine and fuel as the GEM-10, is a two-unit (cow-calf) switcher GTEL with a B-B+B-B wheel arrangement. The slave unit of this locomotive is used as a fuel tender with compressed natural gas (CNG) and does not have a prime mover, so its traction motors are powered by the main section. The turbine of this locomotive also has a maximum power output of 1,000kW (1,300hp).[19]
GT1h-001 during a test rideGT1h-002
The GT1-001 freight GTEL, rebuilt from a VL15electric locomotive in 2006 and introduced in 2007, runs on LNG and has a maximum power output of 8,300kW (11,100hp).[20] One section carries the LNG tank and the other houses the turbine with electric power generation, and both sections have traction motors and cabs. The locomotive has a B-B-B+B-B-B wheel arrangement, and up to three GT1 locomotives can be coupled together.[21] On 23January 2009, the GT1-001 conducted a test run with a 159-car train weighing 15,000 metric tons (14,800 long tons; 16,500 short tons); further heavy-haul tests were carried out in December 2010.[22] In a test run conducted in September 2011, the locomotive pulled 170 freight cars weighing 16,000 metric tons (15,700 long tons; 17,600 short tons).[23] In 2012, the helper diesel engine used for shunting operations was replaced with an accumulator, and the locomotive was renamed to GT1h (where 'h' stands for hybrid). The GT1h-001 remained a prototype and never went into production.[24]
The GT1h-001's successor is the GT1h-002. Despite the same type designation, this locomotive has a fundamentally different design with a (B-B)-(B-B)+(B-B)-(B-B) wheel arrangement, derived from the TEM7 diesel shunting locomotive, and the new body with open LNG tank, derived from the body of the 2ES6 electric locomotive. This serial type has a maximum power output of 8,500kW (11,400hp).[24] Both GT1h locomotives are in operation in Egorshino in the Ural region.[17]
Canada
The Turbo Train at Kingston, Ontario, Canada
Canadian National Railways (CN) was one of the operators of the Turbo, which were passed on to Via Rail. They operated on the major Toronto–Montreal route between 1968 and 1982, when they were replaced by the LRC.
In 2002, Bombardier Transportation announced the launch of the JetTrain, a high-speed trainset consisting of tilting carriages and a locomotive powered by a Pratt & Whitney turboshaft engine. Proposals were made to use the trains for Quebec City–Windsor, Orlando–Miami, and in Alberta, Texas, Nevada and the UK. One prototype was built and tested, but no JetTrains have yet been sold for service. However, nothing ever came of any of these proposals, and the JetTrain essentially disappeared, being superseded by the Bombardier Zefiro line of conventionally powered high speed and very high speed trains. The JetTrain no longer appears on any of Bombardier's current web sites or promotional materials, although it can still be found on older web sites bearing the Canadair logos.
The first TGV prototype, TGV 001, was powered by a gas turbine, but steep oil prices prompted the change to overhead electric lines for power delivery. However, two large classes of gas-turbine powered intercity railcars were constructed in the early 1970s (ETG and RTG) and were used extensively up to about 2000.
SNCF (French National Railways) used a number of gas-turbine trainsets, called the Turbotrain, in non-electrified territory. These typically consisted of a power car at each end with three cars between them. Turbotrain was in use up until 2005. After retirement, four sets were sold for further use in Iran.
Coal-firing
In the 1940s and 1950s research was conducted, in both the US and UK, aimed at building gas turbine locomotives that could run on pulverized coal. The main problem was to avoid erosion of the turbine blades by particles of ash. Only one working example is known to have been produced and it was written off as a failure following testing. The sources for the following information are Robertson[25] and Sampson.[6]
United States
In 1946, a Northrop-Hendy partnership launched an attempt to adapt the Northrop Turbodyne aircraft engine for locomotive use, with coal dust rather than kerosene as a fuel. In December 1946, Union Pacific donated their retired M-10002streamliner locomotive to the project. However, the project was abandoned by the end of 1947 and there is no clear evidence that the locomotive provided for the experiment ever actually moved under gas turbine power or even had it installed.[26] Details of the research were passed to Britain's London, Midland and Scottish Railway. Following a rise in fuel prices that was making their oil-fired GTELS uneconomic, UP experimentally revived the coal-fired gas turbine idea in the early 1960s, producing one prototype coal GTEL in October 1962. The problems with blade fouling and erosion were severe. The project was declared a failure after 20 months, during which time the locomotive ran less than 10,000 miles.
According to Sampson, the plan was to use indirect heating. The pulverized coal would be burned in a combustion chamber and the hot gases passed to a heat exchanger. Here, the heat would be transferred to a separate body of compressed air which would power the turbine. Essentially, it would have been a hot air engine using a turbine instead of a piston.
Robertson shows a diagram that confirms Sampson's information but also refers to problems with erosion of turbine blades by ash. This is strange because, with a conventional shell and tube heat exchanger, there would be no risk of ash entering the turbine circuit.
Working cycle
There were two separate, but linked, circuits: the combustion circuit and the turbine circuit.
Combustion circuit. Pulverized coal and air were mixed and burned in a combustion chamber and the hot gases passed to a heat exchanger where heat was transferred to the compressed air in the turbine circuit. After leaving the heat exchanger the combustion gases entered a boiler to generate steam for train heating.
Turbine circuit. Air entered the compressor and was compressed. The compressed air passed to the heat exchanger where it was heated by the combustion gases. The heated compressed air drove two turbines; one to drive the compressor and the other to power the locomotive. The turbine exhaust (which was hot air) then entered the combustion chamber to support the combustion.
Specification
The locomotive was never built but the specification was as follows:
Wheel arrangement: C-C, later changed to 1A1A-A1A1
Horsepower: 1,800, later reduced to 1,500
Weight: 117 tons, later increased to 150 tons
The projected output was:
Tractive effort,
30,000lbf (130kN) at 72mph (116km/h)
45,000lbf (200kN) at 50mph (80km/h)
Thermal efficiency,
10% at 1/10 load
16% at half load
19% at full load
The transmission was to be mechanical, via a two-speed gearbox, giving a high speed for passenger working and a lower speed for freight. The tractive effort figures, quoted above, look suspiciously high for the specified speeds. It seems more likely that the figures quoted are for starting tractive effort and maximum speed in high gear and low gear respectively. There is a model of the proposed locomotive at Glasgow Museum of Transport and some records are held at the National Railway Museum.
A locomotive is a rail transport vehicle that provides the motive power for a train. If a locomotive is capable of carrying a payload, it is usually rather referred to as a multiple unit, motor coach, railcar or power car; the use of these self-propelled vehicles is increasingly common for passenger trains, but rare for freight trains.
A gas turbine, gas turbine engine, or also known by its old name internal combustion turbine, is a type of continuous flow internal combustion engine. The main parts common to all gas turbine engines form the power-producing part and are, in the direction of flow:
The Napier Deltic engine is a British opposed-piston valveless, supercharged uniflow scavenged, two-stroke diesel engine used in marine and locomotive applications, designed and produced by D. Napier & Son. Unusually, the cylinders were disposed in a three-bank triangle, with a crankshaft at each corner of the triangle.
A diesel locomotive is a type of railway locomotive in which the power source is a diesel engine. Several types of diesel locomotives have been developed, differing mainly in the means by which mechanical power is conveyed to the driving wheels. The most common are diesel-electric locomotives and diesel-hydraulic.
The AAR wheel arrangement system is a method of classifying locomotive wheel arrangements that was developed by the Association of American Railroads. Essentially a simplification of the European UIC classification, it is widely used in North America to describe diesel and electric locomotives. It is not used for steam locomotives, which use the Whyte notation instead.
GT3 was a prototype mainline gas turbine locomotive built in 1961 by English Electric at its Vulcan Foundry in Newton-le-Willows to investigate the use of its gas turbines in rail traction applications. It followed 18000 and 18100 as gas turbines 1 and 2. It was designed by English Electric engineer J. O. P. Hughes in a project that started in the early 1950s. Externally it resembled a steam tender locomotive, but the tender carried kerosene fuel. The designer said the traditional chassis and mechanical transmission avoided complications with relatively untried technologies for bogies and electrical transmission.
British Rail 18000 was a prototype mainline gas turbine-electric locomotive built for British Railways in 1949 by Brown, Boveri & Cie. An earlier gas-turbine locomotive, 18100, had been ordered from Metropolitan-Vickers by the Great Western Railway but construction was delayed due to World War II; a second, 18000, was thus ordered from Switzerland in 1946. It spent its working life on the Western Region of British Railways, operating express passenger services from Paddington station, London.
Class 80 was the TOPS classification allocated by British Rail to the prototype 25 kV AC electric locomotive. This locomotive was built by Metropolitan-Vickers, initially as a prototype gas turbine-electric locomotive, numbered 18100. British Rail allocated the number E1000 to the locomotive following its conversion from gas turbine propulsion.
The Turbotrain was any of several French high-speed, gas turbine trains. The earliest Turbotrain entered service in 1967, for use on France's SNCF intercity lines. There were four versions in total, with the last exiting service in 2005, and it is the Turbotrain that made advances possible for the TGV.
A steam turbine locomotive was a steam locomotive which transmitted steam power to the wheels via a steam turbine. Numerous attempts at this type of locomotive were made, mostly without success. In the 1930s this type of locomotive was seen as a way both to revitalize steam power and challenge the diesel locomotives then being introduced.
The JetTrain was an experimental high-speed passenger train concept created by Bombardier Transportation in an attempt to make European-style high-speed service more financially appealing to passenger railways throughout North America. It was designed to use the same LRC-derived tilting carriages as the Acela Express trains that Bombardier built for Amtrak in the 1990s, which used all-electric locomotives. Unlike the Acela, which is powered electrically by overhead lines, the JetTrain would have used a combination of a 4,000-horsepower (3.0 MW) gas-turbine engine, a low-power diesel engine, a reduction gearbox, and two alternators to power electric traction motors. This would have allowed it to run at high speeds on non-electrified lines.
British Rail 18100 was a prototype main line gas turbine-electric locomotive built for British Railways in 1951 by Metropolitan-Vickers, Manchester. It had, however, been ordered by the Great Western Railway in the 1940s, but construction was delayed due to World War II. It spent its working life on the Western Region of British Railways, operating express passenger services from Paddington station, London.
Co-Co is the wheel arrangement for diesel and electric locomotives with two six-wheeled bogies with all axles powered, with a separate traction motor per axle. The equivalent UIC classification (Europe) for this arrangement is Co′Co′, or C-C for AAR.
A jackshaft is an intermediate shaft used to transfer power from a powered shaft such as the output shaft of an engine or motor to driven shafts such as the drive axles of a locomotive. As applied to railroad locomotives in the 19th and 20th centuries, jackshafts were typically in line with the drive axles of locomotives and connected to them by side rods. In general, each drive axle on a locomotive is free to move about one inch (2.5 cm) vertically relative to the frame, with the locomotive weight carried on springs. This means that if the engine, motor or transmission is rigidly attached to the locomotive frame, it cannot be rigidly connected to the axle. This problem can be solved by mounting the jackshaft on unsprung bearings and using side-rods or chain drives.
The Union Pacific GTELs were a series of gas turbine-electric locomotives built by Alco-GE and General Electric between 1952-1961 and operated by Union Pacific from 1952 to 1970.
Am 4/6 1101 was the world's first gas turbine-electric locomotive. The locomotive was ordered by the Swiss Federal Railways (SBB-CFF-FFS) from the Swiss Locomotive and Machine Works (SLM) and Brown, Boveri & Cie (BBC) in 1939. The locomotive was delivered in 1941 and was in use on railroads in Switzerland, France and Germany until 1954.
The Fairbanks-Morse 38 8-1/8 is a diesel engine of the two-stroke, opposed-piston type. It was developed in the 1930s, and is similar in arrangement to a contemporary series of German Bombers aircraft diesels. The engine was used extensively in US diesel electric submarines of the 1940s and 1950s, as backup power on most US nuclear submarines, as well as in other marine applications, stationary power generation, and briefly, locomotives. A slightly modified version, the 38ND 8-1/8, continues in service on Los Angeles-, Seawolf-, and Ohio-class nuclear submarines of the US Navy. The 38 8-1/8 has been in continuous production since its development in 1938, and is currently manufactured by a descendant of Fairbanks-Morse, FMDefense, in Beloit, Wisconsin.
The South African Railways gas-electric locomotive of 1923 was an experimental gas-electric locomotive. The fuel, suction gas, was generated on-board the locomotive from coal.
An internal combustion locomotive is a type of railway locomotive that produces its pulling power using an internal combustion engine. These locomotives are fuelled by burning fossil fuels, most commonly oil or gasoline, to produce rotational power which is transmitted to the locomotive's driving wheels by various direct or indirect transmission mechanisms. The fuel is carried on the locomotive.
A combined cycle powered locomotive is a patented idea to use two primary movers, a gas turbine with a steam turbine to gain the efficiency of a combined cycle power plant or a combined gas and steam engine. Steam locomotives were tested in the past but were not ideal for low speeds, and gas turbine locomotives (GTELs) were used by Union Pacific until the 1970s. Combined cycle power uses the heat from the gas turbine to make steam from the water to turn a steam turbine, instead of that heat getting exhausted out and wasted. Engine efficiency for combined cycle can achieve 60% compared to diesel motors' 45% efficiency.
↑ Hughes, J.O.P. (14 December 1961). "The Design and Development of a Gas Turbine Locomotive". J. Inst. Locomotive Engineers. 52:2 (286): 180–220. Paper Nº633.
↑ Valery Kossov (2007). "Маневровый газотурбовоз ТГЭМ10"[Switcher gas-turbine locomotive TGEM10](PDF). Transport of Russia (in Russian). pp.18–19. Retrieved 19 December 2021– via rostransport.com.
Allen, Geoffrey Freeman (February–March 1982). "The rise and fall of the turbine". Rail Enthusiast. EMAP National Publications. pp.6–11. ISSN0262-561X. OCLC49957965.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
