GT3 | |||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
GT3 at Leicester, 1961 | |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
| |||||||||||||||||||||||||
|
GT3 (Gas Turbine 3) was a prototype mainline gas turbine locomotive built in 1961 by English Electric at its Vulcan Foundry in Newton-le-Willows to investigate the use of its gas turbines in rail traction applications. It followed 18000 and 18100 as gas turbines 1 and 2. It was designed by English Electric engineer J. O. P. Hughes in a project that started in the early 1950s. Externally it resembled a steam tender locomotive, but the tender carried kerosene fuel. The designer said the traditional chassis and mechanical transmission avoided complications with (at the time of its conception) relatively untried technologies for bogies and electrical transmission. [1]
The National Railway Museum Archives hold the JOP Hughes papers which contain initial concept sketches for various 4-8-4 wheel arrangement single-unit configurations of the machine and early 4-6-0 tender locomotive drawings. These early concept drawings show various names, numbers and liveries, and were drawn with Boxpok-type wheels. [2] The final design was for a 4-6-0 wheel arrangement locomotive with a fuel tender, looking much like a traditional steam locomotive in form. [2]
As constructed the locomotive was built with bespoke heavy steel frames which not only bore the auxiliaries, combustion chamber, turbines, heat exchanger and locomotive cab, but also provided adhesive weight for the finished machine. The frames were carried by a leading two-axle outside-framed bogie and three main axles. The driving wheels were of conventional design in the finished locomotive and were of 5 feet 9 inches (1.75 m) diameter with 19 spokes [2] and conventional balance weights. The centre axle mounted a mechanical transmission shaft driven from the turbine assembly, with power to the outer axles being transmitted by side rods. Power came from an English Electric EM27L gas turbine arrangement of 2,750 hp (2,050 kW) with high- and low-pressure turbines. The low-pressure turbine ran continuously in operation and was used to drive the locomotive's auxiliaries, with the high-pressure turbine operating as higher power outputs were required. [1] Both the locomotive and its fuel tender were vacuum-braked, with vacuum brake ejectors being driven by air pressure bled from the turbine. The locomotive's other auxiliaries (housed in its leading end beneath the large side air intakes) were shaft- and belt-driven.
The tender was permanently coupled behind the locomotive and contained a Spanner train heating boiler at the leading end and fuel tanks either side of a central corridor with a boiler water tank beneath. A crew toilet compartment and British Standard corridor connection were located at the rear. The six-wheel chassis was based on then standard British Railways practice, albeit it with specially made and shaped side frames and bespoke tank and bodywork assembled at Vulcan Foundry. [1] [2] The locomotive had a designed maximum speed of 90 mph (140 km/h), weighed 123.5 long tons (125.5 t; 138.3 short tons), and was painted in a lined Beech Leaf Brown Livery, earning it the nickname The Chocolate Zephyr by railway enthusiasts. Underframes, grilles and the front access and cab doors were painted Brunswick Green with lettering and lining in Orange.
The locomotive was taken to British Railways' Rugby test centre in an incomplete state for testing on rollers, and then on a short section of specially laid track. After returning to Vulcan Foundry for final assembly, the locomotive was then based at the former locomotive shed at Whitchurch in Shropshire for initial light testing and crew training on the Malpas line between Crewe and Chester, before commencing loaded test runs to Llandudno Junction. One of these runs was filmed from on board the locomotive by British Movietone News and the resulting film also showed the locomotive being turned on Llandudno Junction turntable. In the event not all of the planned North Wales Coast Line test runs were completed. [3]
GT3 then moved to Leicester Shed on the Great Central Main Line line for testing and crew training between Leicester and Woodford Halse and then Leicester and Marylebone. Leicester was convenient for English Electric's Whetstone turbine works. During this period it was displayed at Marylebone for the 50th anniversary of the Institute of Locomotive Engineers. The event ran from 11 to 14 May 1961 and GT3 was filmed by British Pathé being inspected by the Duke of Edinburgh. [4] Later testing was undertaken on the West Coast Main Line from Crewe over Shap Summit to Carlisle. [3] On one of these runs Oswald Nock travelled on board and was able to both witness the locomotive in operation and record its performance, his log of the trip later appearing in The Railway Magazine 's practice and performance feature for February 1962. [5] Commenting on the testing the designer noted that, despite some of the expected teething troubles and modifications, once it had departed on a test run GT3 had never failed to complete its booked workings. The locomotive was described as being comfortable and easy to handle for the crew, with conversation at normal volumes possible in the fully enclosed cab. [1]
Despite returning favourable performances on longer runs requiring sustained power outputs, the prototype nature of the locomotive would have required further investigation and development into a configuration which would have matched the convenience of the new double-ended diesel-electric locomotives then being built. Neither English Electric or British Railways were prepared to fund this work [2] as they were committed to diesel-electric locomotives.They were rapidly becoming the future of rail traction with ever-improving power-to-weight ratios.
Upon completion of the Shap test runs GT3 was returned to English Electric at Vulcan Foundry at the end of 1962 and stored. Following internal correspondence in September 1965 [2] the locomotive was partially dismantled and its turbine and heat exchanger equipment removed. It was finally scrapped at Thos. W. Ward, Salford in February 1966 having been towed there by a Standard class steam locomotive. [3] [6]
The most complete record of the locomotive is contained in the paper written by its designer in 1962 [1] and in his papers now held at the National Railway Museum Archives in York. [2] Much of what had been written about the locomotive was based on conjecture until these sources became available; subsequently an article in The Railway Magazine for December 2015 brought together an accurate and verifiable record of the locomotive. [7] No detailed engineering drawings of the locomotives as built are thought to have survived, the York archive containing an internal memo instructing that these were to be returned to the Gas Turbine division of English Electric when dismantling commenced in 1965. [2] Several articles with drawings have appeared in the railway modelling press since the locomotive was scrapped, but most appear to be based on a contemporary sectional view widely published at the time and are flawed with regard to details such as driving wheels (19-spoke), roof and side access hatches, cab rear, tender front and tender rear. The most accurate drawing appears to have been a contemporary "Skinley" drawing produced with the assistance of JOP Hughes. A copy resides with correspondence between Hughes and Skinley in the JOP Hughes papers at the National Railway Museum. [2] In recent years a 5-inch (127 mm) gauge turbine powered model of the locomotive has been built and exhibited in the UK.
Canadian-based Model Railway manufacturer KR Models announced that would be creating a OO Scale model of the GT3 in its prototype brown livery in 2018, and the model was delivered in 2020. [8] [9]
A locomotive or engine is a rail transport vehicle that provides the motive power for a train. If a locomotive is capable of carrying a payload, it is usually rather referred to as a multiple unit, motor coach, railcar or power car; the use of these self-propelled vehicles is increasingly common for passenger trains, but rare for freight trains.
The Vulcan Foundry Limited was an English locomotive builder sited at Newton-le-Willows, Lancashire.
DP2, meaning Development Prototype number 2, was a prototype Type 4 mainline diesel locomotive, built by English Electric in 1962. DP2 was effectively the prototype for the later Class 50; it trialled the engine and electronic systems later used in that class of locomotives.
British Rail 18000 was a prototype mainline gas turbine-electric locomotive built for British Railways in 1949 by Brown, Boveri & Cie. An earlier gas-turbine locomotive, 18100, had been ordered from Metropolitan-Vickers by the Great Western Railway but construction was delayed due to World War II; a second, 18000, was thus ordered from Switzerland in 1946. It spent its working life on the Western Region of British Railways, operating express passenger services from Paddington station, London.
Class 80 was the TOPS classification allocated by British Rail to the prototype 25 kV AC electric locomotive. This locomotive was built by Metropolitan-Vickers, initially as a prototype gas turbine-electric locomotive, numbered 18100. British Rail allocated the number E1000 to the locomotive following its conversion from gas turbine propulsion.
Ruston & Hornsby was an industrial equipment manufacturer in Lincoln, England founded in 1918. The company is best known as a manufacturer of narrow and standard gauge diesel locomotives and also of steam shovels. Other products included cars, steam locomotives and a range of internal combustion engines, and later gas turbines. It is now a subsidiary of Siemens.
The SR V class, more commonly known as the Schools class, is a class of steam locomotive designed by Richard Maunsell for the Southern Railway. The class was a cut down version of his Lord Nelson class but also incorporated components from Urie and Maunsell's LSWR/SR King Arthur class. It was the last locomotive in Britain to be designed with a 4-4-0 wheel arrangement, and was the most powerful class of 4-4-0 ever produced in Europe. All 40 of the class were named after English public schools, and were designed to provide a powerful class of intermediate express passenger locomotive on semi-fast services for lines which could cope with high axle loads but some of which had short turntables.
A gas turbine locomotive is a type of railway locomotive in which the prime mover is a gas turbine. Several types of gas turbine locomotive have been developed, differing mainly in the means by which mechanical power is conveyed to the driving wheels (drivers). A gas turbine train typically consists of two power cars, and one or more intermediate passenger cars.
A steam turbine locomotive is a steam locomotive which transmits steam power to the wheels via a steam turbine. Numerous attempts at this type of locomotive were made, mostly without success. In the 1930s this type of locomotive was seen as a way both to revitalize steam power and challenge the diesel locomotives then being introduced.
The X class is a class of diesel locomotives built by English Electric for the Tasmanian Government Railways between 1950 and 1952. They were the first class of diesel locomotive to enter mainline service on a Government-owned railway in Australia.
British Rail 18100 was a prototype main line gas turbine-electric locomotive built for British Railways in 1951 by Metropolitan-Vickers, Manchester. It had, however, been ordered by the Great Western Railway in the 1940s, but construction was delayed due to World War II. It spent its working life on the Western Region of British Railways, operating express passenger services from Paddington station, London.
The British Rail Class 23 were a class of ten Bo-Bo diesel-electric locomotives built by the English Electric Company (EE) in 1959. The power unit used was a Napier Deltic T9-29 9-cylinder engine of 1,100 bhp (820 kW) driving an EE generator, which powered the four traction motors. They were numbered from D5900 to D5909.
LNER Peppercorn Class A1 No. 60163 Tornado is a 4-6-2 steam locomotive completed in 2008 to an original design by Arthur Peppercorn. It is the first new build British mainline steam locomotive since 1960, and the only Peppercorn Class A1 in existence after the original batch were scrapped. In 2017, Tornado became the first steam locomotive to officially reach 100 mph (160 km/h) on British tracks in over 50 years.
The New Zealand DG and DH class were classes of forty-two diesel-electric locomotives operated on New Zealand's rail network between 1955 and 1983.
The Union Pacific GTELs were a series of gas turbine-electric locomotives built by Alco-GE and General Electric between 1952-1961 and operated by Union Pacific from 1952 to 1970.
The South African Railways Class 5E, Series 1 of 1955 was an electric locomotive.
The Indian locomotive class WCG-1 is a class of 1.5 kV DC electric locomotives that was developed in the late 1920s by Vulcan Foundry and Swiss Locomotive and Machine Works (SLM for Indian Railways. The model name stands for broad gauge, Direct Current, Freight traffic engine, 1st generation. They entered service in 1930. A total of 41 WCG-1 was built at England between 1928 and 1929.
The Indian locomotive class WCM-1 is a class of 1.5 kV DC electric locomotives that was developed in 1954 by Vulcan Foundry and English Electric for Indian Railways. The model name stands for broad gauge (W), Direct Current (C), Mixed traffic (M) engine, 1st generation (1). They entered service in 1955. A total of 7 WCM-1 locomotives were built in England between 1954 and 1955.
The Indian locomotive class WCM-2 is a class of 1.5 kV DC electric locomotives that was developed in 1956 by Vulcan Foundry and English Electric for Indian Railways. The model name stands for broad gauge (W), Direct Current (C), Mixed traffic (M) engine, 2nd generation (2). They entered service in 1957. A total of 12 WCM-2 locomotives were built in England between 1956 and 1957.
The Indian locomotive class WCM-3 is a class of 1.5 kV DC electric locomotives that was developed in 1958 by Hitachi for Indian Railways. The model name stands for broad gauge (W), Direct Current (C), Mixed traffic (M) engine, 3rd generation (3). They entered service in 1958. A total of 3 WCM-3 locomotives were built in Japan in 1958.