General Electric GEnx

Last updated
GEnx
GEnx.png
General Electric GEnx at the Paris Air Show 2009
Type Turbofan
National origin United States
Manufacturer GE Aerospace
First run2006
Major applications Boeing 747-8
Boeing 787
Developed from General Electric GE90
Developed into CFM International LEAP
General Electric GE9X

The General Electric GEnx ("General Electric Next-generation") is an advanced dual rotor, axial flow, high-bypass turbofan jet engine in production by GE Aerospace for the Boeing 747-8 and 787. The GEnx succeeded the CF6 in GE's product line.

Contents

Development

GEnx on 747-8I prototype General Electric GEnx on 747-8I prototype.jpg
GEnx on 747-8I prototype

As of 2016, the GEnx and the Rolls-Royce Trent 1000 were selected by Boeing following a run-off between the three big engine manufacturers. The GEnx uses some technology from the GE90 turbofan, [1] including swept composite fan blades and the 10-stage high-pressure compressor (HPC) featured in earlier variants of the engine. The engine carries composite technology [2] into the fan case.

The engine market for the 787 is estimated at US$40 billion over the next 25 years.[ when? ] A first is the elimination of bleed air systems using high temperature/high pressure air from the propulsion engines to power aircraft systems such as the starting, air-conditioning and anti-ice systems. Both engines enable the move towards the More Electric Aircraft, that is, the concept of replacing previously hydraulic and pneumatic systems with electrical ones to reduce weight, increase efficiency, and reduce maintenance requirements.

The GEnx was expected[ when? ] to produce thrust from 53,000 to 75,000 lbf (240 to 330 kN) with first tests commencing in 2006 and service entry by 2008 (delayed by 787 deliveries). Boeing predicts[ when? ] reduced fuel consumption of up to 20% and significantly quieter engines than current turbofans. A 66,500 lbf (296 kN) thrust version (GEnx-2B67) will be used on the 747-8. Unlike the initial version for the 787, this version has a traditional bleed air system to power internal pneumatic and ventilation systems. It will also have a smaller overall diameter than the initial model to accommodate installation on the 747.

In March 2006 General Electric began initial test runs of the bleedless GEnx variant. [3] The first flight with one of these engines took place on 22 February 2007, using a Boeing 747-100, fitted with one GEnx engine in the number 2 (inboard left hand side) position.

By fall 2019, General Electric was offering the GEnx-2B, developed for the 747-8, for the revised 767-XF variant based on the 767-400ER, but needed enough volume to cover the new product certification. [4]

Operational history

Introduced in late 2011 on a 747-8 freighter, Cargolux surpassed one million flight hours in early 2017. [5]

On July 28, 2012, the NTSB initiated an investigation of an engine failure that occurred on a Boeing 787 during a pre-delivery taxi test in Charleston, South Carolina. [6]

On August 31, 2012, a GEnx-1B engine installed on a Boeing 787 that had not yet flown was found to have an indication of a similar crack on the fan midshaft. The fan midshaft was removed from the engine for further inspection and examination. As a result of investigative work the NTSB has determined that the fan midshafts on the GEnx engines fractured or cracked at the forward end of the shaft where the retaining nut is installed. [6]

On September 11, 2012, an AirBridgeCargo 747-8F experienced a major engine malfunction that spread a significant amount of metallic debris on the runway when the low-pressure turbine shaft separated and shifted backwards, damaging the low pressure turbine blades and vanes. [7] The NTSB issued urgent safety recommendations to the FAA to require ultrasonic scans for midshaft fractures before use of GEnx engines and require repetitive on-wing inspections of the engine to detect cracks. [6] [8]

During the spring and summer of 2013, GE learned of four 747-8F freighters that suffered icing in their engines at altitudes of 40,000 feet (12,192 m) and above. The most serious incident involved an AirBridgeCargo freighter; on July 31, while at an altitude of 41,000 feet (12,497 m) over China, the flight crew noted two engines surging while a third lost substantial power. The pilots were able to land the plane safely but the engines were found to have sustained damage. Among the possible factors cited was "'unique convective weather systems' such as unusually large thunderstorms reaching high altitudes." Boeing is working with GE on software solutions to the problem. [9] Altitude was restricted until GE changed the software to detect the high-altitude ice crystals and open bleed air valve doors to eject them before they enter the core. [5]

Front view of a GEnx-1B on a Vietnam Airlines 787-10 Vietnam Airlines 787-10 VN-A879 GEnx-1B nacelle.jpg
Front view of a GEnx-1B on a Vietnam Airlines 787-10

In March 2014, a GEnx-powered Boeing 787 had its first in-flight shut down in operation when a JAL flight had to divert to Honolulu after an oil pressure alert, bringing its in-flight shut down rate to 1 per 278,000 hours. [10] In January 2016 a Japan Airlines 787 had an inflight shutdown after flying through icing conditions, caused by ice formed on fan blades and ingested: the blades moved forward slightly and rubbed on the abradable seal in the casing. [5] In March 2016, the US FAA ordered emergency fixes on the GEnx-1B PIP2. [11] The airworthiness directive affects 43 Boeing 787 Dreamliners in the US. [12] Abradable material in the casing in front of the fan blades was ground to keep them from rubbing when ingesting ice or debris on 330 GEnx PIP-2. [5]

In early 2018, of 1,277 orders for the Boeing 787, 681 selected the GEnx (53.3%), 420 the Rolls-Royce Trent 1000 (32.9%) and 176 were undecided (13.8%). [13] The 2,000th GEnx was delivered by November 2019, 15 years after the engine launch, as it logged 4.5 million flight cycles and 26 million hours among 60 operators. [14]

Design

Fan blades and outlet guide vanes of GEnx-2B Fan blades and inlet guide vanes of GEnx-2B.jpg
Fan blades and outlet guide vanes of GEnx-2B
Detail of GEnx core Detail of GEnx turbofan engine core.jpg
Detail of GEnx core

The GEnx is derived from the GE90 with a fan diameter of 111.1 in (282 cm) for the 787 and 104.7 in (266 cm) for the 747-8. To reduce weight, it features 18 composite fan blades, a composite fan case and titanium aluminide stage 6 and 7 low-pressure turbine blades. Fuel efficiency is improved by 15% compared to the CF6, the bypass ratio reaches up to 9.0:1 and the overall pressure ratio up to 58.1:1. It has a 10 stage high-pressure compressor and is quieter, helped by larger, more efficient fan blades. [15]

It stays on wing 20% longer, uses 30% fewer parts to lower maintenance costs and has a contra-rotating architecture. [16] The Lean TAPS combustor reduces NOx gases with required pressure loss and backflow margin. [17]

Fan blades have steel alloy leading edges and the composite fan case reduces thermal expansion. To reduce fuel burn, the 23:1 pressure ratio high-pressure compressor is based on the GE90-94B, shrouded guide vanes reduce secondary flows and counter-rotating spools for the reaction turbines reduce load on guide vanes. [18]

To reduce maintenance cost and increase engine life, spools with lower parts count are achieved by using blisks in some stages, low blade counts in other stages and by using fewer stages; internal engine temperatures are reduced due to more efficient cooling techniques and debris extraction within the low-pressure compressor protects the high-pressure compressor.

Applications

Variants

GEnx-1B/2B variants [19]
DesignationEASA certificationContinuousTake-off rating
GEnx-1B29 March 2011
GEnx-1B/P13 July 2012
GEnx-1B/P224 June 2013
GEnx-1B54/P2250.4 kN (56,300 lbf)255.3 kN (57,400 lbf)
GEnx-1B58/P2271.3 kN (61,000 lbf)
GEnx-1B64/P2273.6 kN (61,500 lbf)298.0 kN (67,000 lbf)
GEnx-1B67/P217 May 2018308.7 kN (69,400 lbf)
GEnx-1B70/P2295.8 kN (66,500 lbf)321.6 kN (72,300 lbf)
GEnx-1B70/72/P2
GEnx-1B70/75/P2
GEnx-1B74/75/P2305.2 kN (68,600 lbf)341.2 kN (76,700 lbf)
GEnx-1B76/P2349.2 kN (78,500 lbf)
GEnx-1B76A/P2
GEnx-1B78/P2357.6 kN (80,400 lbf)
GEnx-1B75/P2306.0 kN (68,800 lbf)345.2 kN (77,600 lbf)
GEnx-2B6729 March 2011260.2 kN (58,500 lbf)299.8 kN (67,400 lbf)
GEnx-2B67B21 October 2011
GEnx-2B67/P24 January 2014

Specifications

Rear view of a GEnx-1B on a Jetstar 787-8, showing noise-reducing chevrons General Electric GEnx-1B (14233497776) (cropped).jpg
Rear view of a GEnx-1B on a Jetstar 787-8, showing noise-reducing chevrons
Data sheet [20]
Variant-1B70-1B74/75-1B76/78-2B67B
Application787-8787-9787-10747-8
Fan Diameter111.1 in (282 cm)104.7 in (266 cm)
Compressor 1 Fan 4 LP 10 HP1 Fan 3 LP 10 HP
Turbine 2 HP 7 LP2 HP 6 LP
Takeoff thrust 69,800 lbf (310 kN)74,100 lbf (330 kN)76,100 lbf (339 kN)66,500 lbf (296 kN)
Takeoff Bypass ratio 9.39.19.18.0
Takeoff OPR [21] 43.846.347.444.7
Top-of-climb OPR53.355.458.152.4
Takeoff air per sec.2,559 lb (1,161 kg)2,624 lb (1,190 kg)2,658 lb (1,206 kg)2,297 lb (1,042 kg)
Flange to flange184.7 in (469 cm)169.7 in (431 cm)
Nominal RPM [22] LP 2,560, HP 11,377LP 2,835, HP 11,377
Dry weight [22] 13,552 lb (6,147 kg)12,397 lb (5,623 kg)
Thrust/weight 5.155.475.625.36

See also

Related development

Comparable engines

Related lists

Related Research Articles

<span class="mw-page-title-main">Turbofan</span> Airbreathing jet engine designed to provide thrust by driving a fan

A turbofan or fanjet is a type of airbreathing jet engine that is widely used in aircraft propulsion. The word "turbofan" is a combination of the preceding generation engine technology of the turbojet, and a reference to the additional fan stage added. It consists of a gas turbine engine which achieves mechanical energy from combustion, and a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all the air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust.

<span class="mw-page-title-main">Boeing 787 Dreamliner</span> Boeing wide-body jet airliner introduced in 2011

The Boeing 787 Dreamliner is an American wide-body airliner developed and manufactured by Boeing Commercial Airplanes. After dropping its unconventional Sonic Cruiser project, Boeing announced the conventional 7E7 on January 29, 2003, which focused largely on efficiency. The program was launched on April 26, 2004, with an order for 50 aircraft from All Nippon Airways (ANA), targeting a 2008 introduction. On July 8, 2007, a prototype 787 without major operating systems was rolled out; subsequently the aircraft experienced multiple delays, until its maiden flight on December 15, 2009. Type certification was received in August 2011, and the first 787-8 was delivered in September 2011 before entering commercial service on October 26, 2011, with ANA.

<span class="mw-page-title-main">Pratt & Whitney JT9D</span> Turbofan aircraft engine first flown in 1968

The Pratt & Whitney JT9D engine was the first high bypass ratio jet engine to power a wide-body airliner. Its initial application was the Boeing 747-100, the original "Jumbo Jet". It was Pratt & Whitney's first high-bypass-ratio turbofan.

<span class="mw-page-title-main">Pratt & Whitney PW4000</span> High-bypass turbofan aircraft engine

The Pratt & Whitney PW4000 is a family of dual-spool, axial-flow, high-bypass turbofan aircraft engines produced by Pratt & Whitney as the successor to the JT9D. It was first run in April 1984, was FAA certified in July 1986, and was introduced in June 1987. With thrust ranging from 50,000 to 99,040 lbf, it is used on many wide-body aircraft.

<span class="mw-page-title-main">General Electric GE90</span> High-bypass turbofan aircraft engine


The General Electric GE90 is a family of high-bypass turbofan aircraft engines built by GE Aerospace for the Boeing 777, with thrust ratings from 81,000 to 115,000 pounds-force. It entered service with British Airways in November 1995. It is one of three options for the 777-200, -200ER, and -300 versions, and the exclusive engine of the -200LR, -300ER, and 777F. It was the largest jet engine, until being surpassed in January 2020 by its successor, the 110,000 lbf (490 kN) GE9X, which has a 6-inch (15 cm) larger diameter fan. However, the GE90-115B, the most recent variant, is rated for a higher thrust than the GE9X.

<span class="mw-page-title-main">Rolls-Royce Trent</span> Family of turbofan aircraft engines

The Rolls-Royce Trent is a family of high-bypass turbofans produced by Rolls-Royce. It continues the three spool architecture of the RB211 with a maximum thrust ranging from 61,900 to 97,000 lbf . Launched as the RB-211-524L in June 1988, the prototype first ran in August 1990. Its first variant is the Trent 700 introduced on the Airbus A330 in March 1995, then the Trent 800 for the Boeing 777 (1996), the Trent 500 for the A340 (2002), the Trent 900 for the A380 (2007), the Trent 1000 for the Boeing 787 (2011), the Trent XWB for the A350 (2015), and the Trent 7000 for the A330neo (2018). It has also marine and industrial variants like the RR MT30.

<span class="mw-page-title-main">Pratt & Whitney PW2000</span> Series of high-bypass turbofan aero engines

The Pratt & Whitney PW2000, also known by the military designation F117 and initially referred to as the JT10D, is a series of high-bypass turbofan aircraft engines with a thrust range from 37,000 to 43,000 lbf. Built by Pratt & Whitney, they were designed for the Boeing 757. As a 757 powerplant, these engines compete with the Rolls-Royce RB211.

<span class="mw-page-title-main">Engine Alliance GP7000</span> Turbofan engine manufactured by Engine Alliance

The Engine Alliance GP7000 is a turbofan jet engine manufactured by Engine Alliance, a joint venture between General Electric and Pratt & Whitney. It is one of the powerplant options available for the Airbus A380, along with the Rolls-Royce Trent 900.

<span class="mw-page-title-main">GE Aerospace</span> American aircraft engine manufacturer

General Electric Company, doing business as GE Aerospace, is an American aircraft engine supplier that is headquartered in Evendale, Ohio, outside Cincinnati. It is the legal successor to the original General Electric Company founded in 1892, which split into three separate companies between November 2021 and April 2024, adopting the trade name GE Aerospace after divesting its healthcare and energy divisions.

<span class="mw-page-title-main">General Electric CF6</span> Turbofan aircraft engine family

The General Electric CF6, US military designations F103 and F138, is a family of high-bypass turbofan engines produced by GE Aviation. Based on the TF39, the first high-power high-bypass jet engine, the CF6 powers a wide variety of civilian airliners. The basic engine core also powers the LM2500 and LM6000 marine and power generation turboshafts. It is gradually being replaced by the newer GEnx family.

<span class="mw-page-title-main">Rolls-Royce Trent 500</span> 1990s British turbofan aircraft engine

The Rolls-Royce Trent 500 is a high-bypass turbofan produced by Rolls-Royce to power the larger A340-500/600 variants. It was selected in June 1997, first ran in May 1999, first flew in June 2000, and achieved certification on 15 December 2000. It entered service in July 2002 and 524 engines were delivered on-wing until the A340 production ended in 2012.

<span class="mw-page-title-main">Rolls-Royce Trent 700</span> 1990s British turbofan aircraft engine

The Rolls-Royce Trent 700 is a high-bypass turbofan aircraft engine produced by Rolls-Royce plc to power the Airbus A330. Rolls-Royce was studying a RB211 development for the A330 at its launch in June 1987. It was first selected by Cathay Pacific in April 1989, first ran in summer 1992, was certified in January 1994 and was put into service on 24 March 1995. Keeping the characteristic three-shaft architecture of the RB211, it is the first variant of the Trent family. With its 97.4 in (247 cm) fan for a 5:1 bypass ratio, it produces 300.3 to 316.3 kN of thrust and reaches an overall pressure ratio of 36:1. It competes with the General Electric CF6-80E1 and the PW4000 to power the A330.

<span class="mw-page-title-main">Rolls-Royce Trent 800</span> Turbofan engine produced by Rolls-Royce beginning 1993

The Rolls-Royce Trent 800 is a high-bypass turbofan produced by Rolls-Royce plc, one of the engine options for the early Boeing 777 variants. Launched in September 1991, it first ran in September 1993, was granted EASA certification on 27 January 1995, and entered service in 1996. It reached a 40% market share, ahead of the competing PW4000 and GE90, and the last Trent 800-powered 777 was delivered in 2010. The Trent 800 has the Trent family three shaft architecture, with a 280 cm (110 in) fan. With a 6.4:1 bypass ratio and an overall pressure ratio reaching 40.7:1, it generates up to 413.4 kN of thrust.

<span class="mw-page-title-main">Rolls-Royce Trent 900</span> 2000s British turbofan aircraft engine

The Rolls-Royce Trent 900 is a high-bypass turbofan produced by Rolls-Royce plc to power the Airbus A380, competing with the Engine Alliance GP7000. Initially proposed for the Boeing 747-500/600X in July 1996, this first application was later abandoned but it was offered for the A3XX, launched as the A380 in December 2000. It first ran on 18 March 2003, made its maiden flight on 17 May 2004 on an A340 testbed, and was certified by the EASA on 29 October 2004. Producing up to 374 kN (84,000 lbf), the Trent 900 has the three shaft architecture of the Rolls-Royce Trent family with a 2.95 m (116 in) fan. It has a 8.5–8.7:1 bypass ratio and a 37–39:1 overall pressure ratio.

<span class="mw-page-title-main">Rolls-Royce Trent 1000</span> British turbofan engine, developed from earlier Trent series engines

The Rolls-Royce Trent 1000 is a high-bypass turbofan engine produced by Rolls-Royce, one of the two engine options for the Boeing 787 Dreamliner, competing with the General Electric GEnx. It first ran on 14 February 2006 and first flew on 18 June 2007 before a joint EASA/FAA certification on 7 August 2007 and entered service on 26 October 2011. Corrosion-related fatigue cracking of intermediate pressure (IP) turbine blades was discovered in early 2016, grounding up to 44 aircraft and costing Rolls-Royce at least £1.3 billion.

<span class="mw-page-title-main">General Electric CJ805</span> Civil series of the J79 turbojet aircraft engine

The General Electric CJ805 is a jet engine which was developed by General Electric Aircraft Engines in the late 1950s. It was a civilian version of the J79 and differed only in detail. It was developed in two versions. The basic CJ805-3 was a turbojet and powered the Convair 880 airliner, and the CJ805-23 a turbofan derivative which powered the Convair 990 Coronado variant of the 880.

<span class="mw-page-title-main">General Electric Passport</span> High bypass turbofan aircraft engine

The General Electric Passport is a turbofan developed by GE Aerospace for large business jets. It was selected in 2010 to power the Bombardier Global 7500 and 8000, first run on June 24, 2013, and first flown in 2015. It was certified in April 2016 and powered the Global 7500 first flight on November 4, 2016, before its 2018 introduction. It produces 14,000 to 20,000 lbf of thrust, a range previously covered by the General Electric CF34. A smaller scaled CFM LEAP, it is a twin-spool axial engine with a 5.6:1 bypass ratio and a 45:1 overall pressure ratio and is noted for its large one-piece 52 in (130 cm) fan 18-blade titanium blisk.

<span class="mw-page-title-main">Rolls-Royce Trent 7000</span> Jet engine

The Rolls-Royce Trent 7000 is a high-bypass turbofan engine produced by Rolls-Royce, an iteration of the Trent family powering exclusively the Airbus A330neo. Announced on 14 July 2014, it first ran on 27 November 2015. It made its first flight on 19 October 2017 aboard on the A330neo. It received its EASA type certification on 20 July 2018 as a Trent 1000 variant. It was first delivered on 26 November, and was cleared for ETOPS 330 by 20 December. Compared to the A330's Trent 700, the 68,000–72,000 lbf (300–320 kN) engine doubles the bypass ratio to 10:1 and halves emitted noise. Pressure ratio is increased to 50:1, and it has a 112 in (280 cm) fan and a bleed air system. Fuel consumption is improved by 11%.

<span class="mw-page-title-main">General Electric GE9X</span> High-thrust turbofan jet engine

The General Electric GE9X is a high-bypass turbofan developed by GE Aerospace exclusively for the Boeing 777X. It first ran on the ground in April 2016 and first flew on March 13, 2018; it powered the 777-9's maiden flight in early 2020. It received its Federal Aviation Administration (FAA) type certificate on September 25, 2020. Derived from the General Electric GE90 with a larger fan, advanced materials like ceramic matrix composites (CMCs), and higher bypass and compression ratios, it was designed to improve fuel efficiency by 10% compared to the GE90. It is rated at 110,000 lbf (490 kN) of thrust, which is 5,000 lbf less than the GE90 highest thrust variant, the GE90-115, rated at 115,000 lbf (510 kN).

References

  1. "FAA Orders 'Urgent' 787 Repair After Engine Fails at 20,000 Feet". Bloomberg.com. Bloomberg. 22 April 2016. Retrieved 18 October 2018.
  2. Paur, Jason. "The Innovative 787 Carries Boeing, And Aviation, Ahead". Wired. Retrieved 18 October 2018.
  3. "General Electric Performs First Run of New GEnx Engine". Flight International . 21 March 2006.
  4. Guy Norris (Nov 15, 2019). "GE In Talks With Airbus Over Potential A350neo". Aviation Week.
  5. 1 2 3 4 Sean Broderick (Aug 31, 2017). "Issues With Newest Engines Provide Early MRO-Proving Opportunities". Aviation Week Network .
  6. 1 2 3 "NTSB issues urgent recommendations for GEnx-1B and -2B engines". 2019-12-27. Archived from the original on 27 December 2019. Retrieved 2022-01-25.
  7. "Incident: Air Bridge Cargo B748 at Shanghai on Sep 11th 2012, rejected takeoff". avherald.com. Retrieved 2022-01-25.
  8. "GE identifies installation issue in GEnx, orders inspections". FlightGlobal . Retrieved 6 October 2012.
  9. Pasztor, Andy (October 16, 2013). "Icing Hazards Surface on Boeing's Newest 747 Jet". Wall Street Journal . p. B3. Retrieved June 10, 2014.
  10. Stephen Trimble (9 March 2014). "GE-powered JAL 787 has in-flight shutdown". FlightGlobal.
  11. "FAA orders engine icing fixes for GEnx-powered Boeing 787 Dreamliners". Aviation Safety Network. 2016-04-23.
  12. Patterson, Thom (April 23, 2016). "FAA Orders Urgent Fixes For Boeing 787 Dreamliners". CNN.
  13. "Airbus and Boeing are head-to-head in the widebody sector". FlightGlobal. February 6, 2018.
  14. "GE wraps up GE9X trials as 777X flight tests near". FlightGlobal. 18 Nov 2019.
  15. "The GEnx Commercial Aircraft Engine". GE Aviation.
  16. "GENX high bypass turbofan engines" (PDF). GE Aviation.
  17. General Electric (June 2013). "TAPS II Combustor Final Report" (PDF). Continuous Lower Energy, Emissions and Noise (CLEEN) Program. FAA.
  18. "Designing High-Tech Engines For Easier Maintenance". Aviation Week & Space Technology . Retrieved 18 October 2018.
  19. "Type certificate data sheet" (PDF). EASA. 17 May 2018. Archived from the original (PDF) on 28 September 2018. Retrieved 17 June 2019.
  20. "GENX high bypass turbofan engines" (PDF). GE Aviation. 11 Jan 2017.
  21. "GEnx General Characteristics" (PDF).
  22. 1 2 "Type certificate data sheet number E00078NE, Revision: 14" (PDF). FAA. June 20, 2016. Archived from the original (PDF) on November 15, 2016. Retrieved November 2, 2017.