| T31 | |
|---|---|
 | |
| A T31 in the Presidential Gallery of the National Museum of the United States Air Force | |
| Type | Turboprop |
| National origin | United States |
| Manufacturer | General Electric |
| First run | May 1945 |
| Major applications | Consolidated Vultee XP-81 Ryan XF2R Dark Shark |
| Number built | 28 |
The General Electric T31 (company designation TG-100A) was the first turboprop engine designed and built in the United States.
The TG-100A benefited from the Anglo/American technology exchange with one of its designers, Glenn Warren, stating that one of the most important British contributions was the concept of multiple combustion cans. [1] The GE axial compressor design was directly influenced by NACA with their 8-stage compressor. [1] NACA had developed the theory and designed and tested the compressor. [2]
General Electric adopted a single shaft engine configuration, like the Rolls-Royce Dart , where the turbine drove both the compressor and the propeller reduction gearbox. This epicyclic gearbox was relatively long. Air entered a screened annular intake directly behind the gearbox. After compression, the air entered the combustion chambers in a radially outward direction. These chambers were mounted around the casing of the axial compressor, presumably to shorten the shaft. A portion of the air destined for the combustion chambers was diverted to cool the turbine nozzle guide vanes before entering the outer part of the combustion chambers. Combustion products exiting the chambers discharged through the single stage turbine before entering a rapidly converging annular exhaust terminated by a circular tail pipe. Although the 14 stage all-axial compressor produced a decent pressure ratio (approximately 6.15:1 at design speed; 5.3:1 at Maximum Power, SLS,ISA), it was not particularly efficient. A large diameter turbine facilitated the use of a single stage, whereas the Rolls-Royce Dart (which had a similar engine cycle) required 3 stages. [3]
The General Electric XT31 was first used in the experimental Consolidated Vultee XP-81. [4] The XP-81 first flew in December 1945, the first aircraft to use a combination of turboprop and turbojet power.
The T31 engine was the first American turboprop engine to power an aircraft. [5] It made its initial flight in the Consolidated Vultee XP-81 on 21 December 1945. The T31 was mounted in the nose; an Allison J33 turbojet engine mounted in the rear fuselage provided added thrust. The T31 was also used on the Navy XF2R-1, similarly powered by a turboprop/turbojet engine combination. The engine was to have been flown experimentally on a Curtiss XC-113 (a converted Curtiss C-46), but the experiment was abandoned after the XC-113 was involved in a ground accident. Only 28 T31s were built; none were used in production aircraft, but improved production turboprop engines were developed from the technology pioneered by the T31.
A derivative of the T31, the General Electric TG-110A, given the military designation T41, was ordered but subsequently cancelled.
Data from [6]
Data from World Encyclopaedia of Aero Engines 5th Ed. [7]
Related development
Comparable engines
Related lists
A turboprop is a turbine engine that drives an aircraft propeller.
The Theseus was the Bristol Aeroplane Company's first attempt at a gas-turbine engine design. A turboprop delivering just over 2,000 hp (1,500 kW) was chosen rather than compete with companies that were already developing turbojets. A heat exchanger to transfer waste heat from the exhaust to the compressor exit was necessary to meet a requirement for a fuel consumption comparable to a piston engine. However, the heat exchanger was abandoned after tests showed that it had a high pressure loss and only produced a fuel saving of 8%. Furthermore overall performance was reduced
The Ryan XF2R Dark Shark was an American experimental aircraft built for the United States Navy that combined turboprop and turbojet propulsion. It was based on Ryan Aeronautical's earlier FR Fireball, but replaced the Fireball's piston engine with a turboprop engine.
The Pratt & Whitney J57 is an axial-flow turbojet engine developed by Pratt & Whitney in the early 1950s. The J57 was the first 10,000 lbf (45 kN) thrust class engine in the United States. The J57/JT3C was developed into the J52 turbojet, the J75/JT4A turbojet, the JT3D/TF33 turbofan, and the XT57 turboprop. The J57 and JT3C saw extensive use on fighter jets, jetliners, and bombers for many decades.
The Consolidated Vultee XP-81 is a development of the Consolidated Vultee Aircraft Corporation to build a single seat, long range escort fighter that combined use of both turbojet and turboprop engines. Although promising, the lack of suitable engines combined with the end of World War II doomed the project.
The General Electric/Allison J35 was the United States Air Force's first axial-flow compressor jet engine. Originally developed by General Electric in parallel with the Whittle-based centrifugal-flow J33, the J35 was a fairly simple turbojet, consisting of an eleven-stage axial-flow compressor and a single-stage turbine. With the afterburner, which most models carried, it produced a thrust of 7,400 lbf (33 kN).
The Armstrong Siddeley Mamba was a British turboprop engine produced by Armstrong Siddeley in the late 1940s and 1950s, producing around 1,500 effective horsepower (1,100 kW).
The Rolls-Royce RB.39 Clyde was Rolls-Royce's first purpose-designed turboprop engine and the first turboprop engine to pass its civil and military type-tests.
The Kuznetsov NK-12 is a Soviet turboprop engine of the 1950s, designed by the Kuznetsov design bureau. The NK-12 drives two large four-bladed contra-rotating propellers, 5.6 m (18 ft) diameter (NK-12MA), and 6.2 m (20 ft) diameter (NK-12MV). It is the most powerful turboprop engine to enter service.
The General Electric J31 was the first jet engine to be mass-produced in the United States.
The Bristol Orion aero engine was a two-shaft turboprop intended for use in later marks of the Bristol Britannia and the Canadair CL-44. Although the engine was built and underwent a development program, the BE.25 Orion project was cancelled in 1958 by the British Ministry of Supply in favour of the Rolls-Royce Tyne. In addition, interest in turboprop-powered aircraft was beginning to wane, because of the successful introduction of the Boeing 707 and Douglas DC-8 jetliners into airline service.
The CFE CFE738 is a small turbofan engine aimed at the business/commuter jet market manufactured by the CFE Company, and is used on the Dassault Falcon 2000.
The Rolls-Royce RB.50 Trent was the first Rolls-Royce turboprop engine.
The Turbomeca Astazou is a highly successful series of turboprop and turboshaft engines, first run in 1957. The original version weighed 110 kg (243 lb) and developed 240 kW (320 shp) at 40,000 rpm. It was admitted for aviation service on May 29, 1961, after a 150-hour test run. The main developing engineer was G. Sporer. It was named after two summits of the Pyrenees.
The Allison T40, company designation Allison Model 500, was an early American turboprop engine composed of two Allison T38 power sections driving a contra-rotating propeller via a common gearbox.
The General Electric T64 is a free-turbine turboshaft engine that was originally developed for use on helicopters, but which was later used on fixed-wing aircraft as well. General Electric introduced the engine in 1964. The original engine design included technical innovations such as corrosion resistant and high-temperature coatings. The engine features a high overall pressure ratio, yielding a low specific fuel consumption for its time. Although the compressor is all-axial, like the earlier General Electric T58, the power turbine shaft is coaxial with the HP shaft and delivers power to the front of the engine, not rearwards. Fourteen compressor stages are required to deliver the required overall pressure ratio. Compressor handling is facilitated by 4 rows of variable stators. Unlike the T58, the power turbine has 2 stages.
The Allison T38 was an early turboprop engine developed by Allison Engine Company during the late 1940s. The T38 became the basis for the very successful family of Allison T56 turboprop engine.
The Flader J55, also known as the 124 within the company, was a small turbojet engine notable for its use of a supersonic axial-flow compressor. Development started at Fredric Flader Inc. in 1947, with the first examples being delivered in 1949. However, these delivered far lower power than predicted. Improved models followed in early 1952 that met the performance requirements, but demonstrated very poor reliability. When small engines from other companies became available, the J55 project was cancelled in 1952.
An airbreathing jet engine is a jet engine in which the exhaust gas which supplies jet propulsion is atmospheric air, which is taken in, compressed, heated, and expanded back to atmospheric pressure through a propelling nozzle. Compression may be provided by a gas turbine, as in the original turbojet and newer turbofan, or arise solely from the ram pressure of the vehicle's velocity, as with the ramjet and pulsejet.
During World War 2, the Bristol Aero Engine part of the Bristol Aeroplane Company was pre-occupied with developing and manufacturing radial piston engines, such as the Bristol Hercules and the more powerful Bristol Centaurus. However, in 1944 the Company decided to form a Project Department to investigate the design of gas turbines. Initially the department was based at Tockington Manor, a large country house close to the main factory at Patchway, Bristol. A predominantly young team was formed and was initially tasked with studying turboprop engines.
