LNWR Teutonic Class

Last updated

LNWR Teutonic class
LNWR Webb 3-cylinder compound locomotive 1301 Teutonic (Howden, Boys' Book of Locomotives, 1907).jpg
No. 1301 Teutonic Crewe Works portrait
Type and origin
Power typeSteam
Designer F. W. Webb
Builder Crewe Works
Serial number3102–3111
Build dateMarch 1889 – June 1890
Total produced10
Specifications
Configuration:
   Whyte 2-2-2-0
   UIC 1AA n3v
Gauge 4 ft 8+12 in (1,435 mm)
Leading dia. 3 ft 10+12 in (1.181 m) + tyres
Driver dia.6 ft 10 in (2.083 m) + tyres
Wheelbase:
  Engine18 ft 1 in (5.51 m)
  Leading8 ft 5 in (2.57 m)
  Drivers9 ft 8 in (2.95 m)
Loco weight46 long tons (47 t)
Boiler:
  Diameter4 ft 2 in (1.27 m)
  Tube plates11 ft 0 in (3.35 m)
Boiler pressure175 lbf/in2 (1.21 MPa)
Heating surface1,401.5 sq ft (130.20 m2)
Cylinders Three: two HP (outside), one LP (inside)
High-pressure cylinder14 in × 24 in (356 mm × 610 mm)
Low-pressure cylinder30 in × 24 in (762 mm × 610 mm)
Valve gear
Career
Operators London and North Western Railway
ScrappedOctober 1905 – July 1907
DispositionAll scrapped

The LNWR Teutonic class was a class of 10 passenger three-cylinder compound 2-2-2-0 locomotives designed by F. W. Webb for the London and North Western Railway, and manufactured by them in their Crewe Works between 1889 and 1890.

Contents

Design

No. 1301 Teutonic in black livery 2-4-0 L&NWR 1301 Teutonic.jpg
No. 1301 Teutonic in black livery

The design featured a boiler pressed to 175 lbf/in2 (1.21 MPa) delivering saturated steam to two outside 14-inch (356 mm) high-pressure cylinders, which exhausted to one 30-inch (762 mm) low-pressure cylinder inside the frames. All three cylinders had a stroke of 24 inches (610 mm); the high-pressure cylinders drove the rear wheels, while the low-pressure drove the leading driving wheels. As the two pairs of driving wheels were not connected, the locomotives were "duplex drive" or "double-singles".

They were a development of Webb's Dreadnought class; they had larger driving and leading wheels, and the additions of cylinder tail rods (which were later removed). There were also further modifications to the Joy valve gear, but the seven locomotives built in 1890 had the inside cylinder worked by slip-eccentric valve gear instead from new. [1]

Of the ten locomotives, nine were named after ships of the White Star Line, the exception was named after a character in a Walter Scott novel, as it was exhibited at the Edinburgh International Exhibition of 1890.[ citation needed ]

Decline

When George Whale become chief mechanical engineer of the LNWR in 1903, he started a programme of eliminating Webb's over-complicated duplex compound locomotives. Consequently, the class was scrapped between October 1905, and July 1907, having been replaced by Whale's Experiment class. [1]

Related Research Articles

George Whale was an English locomotive engineer who was born in Bocking, Essex, and educated in Lewisham, London. He worked for the London and North Western Railway (LNWR).

<span class="mw-page-title-main">Crampton locomotive</span> Type of steam locomotive, built from 1846

A Crampton locomotive is a type of steam locomotive designed by Thomas Russell Crampton and built by various firms from 1846. The main British builders were Tulk and Ley and Robert Stephenson and Company.

During the 1880s and 1890s, William Dean constructed a series of experimental locomotives to test various new ideas in locomotive construction for the Great Western Railway.

A compound locomotive is a steam locomotive which is powered by a compound engine, a type of steam engine where steam is expanded in two or more stages. The locomotive was only one application of compounding. Two and three stages were used in ships, for example.

<span class="mw-page-title-main">LNWR Whale Precursor Class</span> Type of steam locomotive

The London and North Western Railway (LNWR) "Precursor" Class was a type of 4-4-0 ("American") steam locomotive designed by the company's Chief Mechanical Engineer, George Whale. Introduced in 1904, it should not be confused with the LNWR 2-4-0 "Precursor" Class of 1874 designed by Francis Webb, the last example of which was scrapped in 1895. In 1906, a 4-4-2T ("Atlantic") tank variant of Webb's engine, the "Precursor Tank" Class, also entered service.

<span class="mw-page-title-main">LSWR T7 class</span>

The LSWR Class T7 4-2-2-0 was a prototype express steam locomotive design by Dugald Drummond for the London and South Western Railway introduced in 1897. Five similar locomotives, classified E10, were introduced in 1901.

The Victorian Railways V Class is a steam locomotive, used on the Victorian Railways in the period 1900-1930.

<span class="mw-page-title-main">LNWR Webb Experiment Class</span>

The London and North Western Railway Experiment Class was a series of 30 three-cylinder 2-(2-2)-0 compound locomotives designed by Francis Webb for the London and North Western Railway between 1882 and 1884. They were Webb’s first large-scale experiment with a class of express compound locomotives, and the first engine was named accordingly. They were followed by a class of similar, but larger locomotives, that featured larger boilers and smaller driving wheels – the LNWR Dreadnought Class.

Under the Whyte notation for the classification of steam locomotives, 2-2-2-0 usually represents the wheel arrangement of two leading wheels on one axle, four powered but uncoupled driving wheels on two axles, and no trailing wheels, but can also be used to represent two sets of leading wheels two driving wheels, and no trailing wheels. Some authorities place brackets around the duplicated but uncoupled wheels, creating a notation 2-(2-2)-0, or (2-2)-2-0, as a means of differentiating between them. Others simply refer to the locomotives 2-2-2-0.

<span class="mw-page-title-main">Duplex locomotive</span> Type of steam locomotive

A duplex locomotive is a steam locomotive that divides the driving force on its wheels by using two pairs of cylinders rigidly mounted to a single locomotive frame; it is not an articulated locomotive. The concept was first used in France in 1863, but was particularly developed in the early 1930s by the Baldwin Locomotive Works, the largest commercial builder of steam locomotives in North America, under the supervision of its then chief engineer, Ralph P. Johnson.

<span class="mw-page-title-main">2-2-2-2</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, 2-2-2-2 could represent either the wheel arrangement of two leading wheels, four powered but uncoupled driving wheels, and two trailing wheels; or of two independent leading axles, two driving wheels, and two trailing wheels.

<span class="mw-page-title-main">LNWR 4ft 6in Tank Class</span>

The LNWR 4ft 6in Tank was a class of 220 passenger 2-4-2T locomotives manufactured by the London and North Western Railway in their Crewe Works between 1879 and 1898. The "4ft 6in" in the title referred to the diameter of the driving wheels – although the stated dimension was for the wheel centres – the nominal diameter including the tyres was 4 ft 8+12 in (1,435 mm).

<span class="mw-page-title-main">LNWR Dreadnought Class</span> Class of British 2-2-2-0 locomotives

The LNWR Dreadnought class was a class of 40 passenger three-cylinder compound 2-2-2-0 locomotives designed by F. W. Webb for the London and North Western Railway, and manufactured by them in their Crewe Works between 1884 and 1888. The railway also commissioned the Beyer, Peacock and Company to construct an additional locomotive of the design for the Pennsylvania Railroad.

<span class="mw-page-title-main">LNWR Greater Britain Class</span> Class of British steam locomotives

The London and North Western Railway (LNWR) Greater Britain class was a class of ten 2-2-2-2 steam locomotives designed for express passenger work by F. W. Webb.

<span class="mw-page-title-main">LNWR John Hick Class</span>

The London and North Western Railway (LNWR) John Hick class was a class of ten 2-2-2-2 steam locomotives designed for express passenger work by F. W. Webb.

<span class="mw-page-title-main">Pennsylvania Railroad no. 1320</span>

The Pennsylvania Railroad no. 1320 was a single experimental passenger three-cylinder compound 2-2-2-0 locomotive purchased by the Pennsylvania Railroad in 1889, based on the London & North Western Railway's Dreadnought class, designed by Francis Webb. As the London & North Western's Crewe Works, which had built the Dreadnought classes, was not legally allowed to sell its locomotives, 1320 was instead constructed by Beyer, Peacock & Company in Manchester to the Dreadnought's specifications.

<span class="mw-page-title-main">LNWR 18in Goods Class</span>

The LNWR 18-inch Goods was a class of 310 0-6-0 freight steam locomotives built by the London and North Western Railway at their Crewe Works between 1880 and 1902.

<span class="mw-page-title-main">LNWR 18in Tank Class</span>

The LNWR 18-inch Tank class was a class of 80 0-6-2T locomotives built by the London and North Western Railway in their Crewe Works between 1898 and 1902.

<span class="mw-page-title-main">LNWR 5ft 6in Tank Class</span>

The LNWR 5ft 6in Tank was a class of 160 passenger 2-4-2T locomotives manufactured by the London and North Western Railway in their Crewe Works between 1890 and 1897. The "5ft 6in" in the title referred to the diameter of the driving wheels – although the stated dimension was for the wheel centres – the nominal diameter including the tyres was 5 ft 8+12 in (1,740 mm).

<span class="mw-page-title-main">LNWR Samson Class</span>

The LNWR Samson Class was a class of ninety 2-4-0 steam locomotives built by the London and North Western Railway at their Crewe Works between 1863 and 1879.

References