Signalling of the Toronto subway

Last updated

The Toronto subway uses a variety of signalling systems on its lines, consisting of a combination of fixed block signalling and moving block signalling technologies.

Contents

The oldest signalling system is known as automatic block signalling and was designed for the system's heavy rail lines: Line 1 Yonge–University, Line 2 Bloor–Danforth and Line 4 Sheppard. Since 2022, Line 1 had been fully converted to automatic train control (ATC). [1] The remaining lines use ATC: Line 3 Scarborough uses an early form of ATC known as transmission-based train control (TBTC), while Line 1 along with Line 5 Eglinton, a light-rail line under construction, use a modern form of ATC called communications-based train control (CBTC).

Transmission-based train control (Line 3)

Line 3 Scarborough used SelTrac IS, a transmission-based train control system originally developed by Alcatel-Lucent (now part of Thales Group) as part of the Intermediate Capacity Transit System (ICTS) technology employed by Line 3, which is identical to that of Vancouver's SkyTrain and the Detroit People Mover. The system was designed to allow Line 3 trains to be driverless; however, due to safety concerns, an operator was stationed at the front of each train in a cab equipped with a display of signal indications; there were no track-side signals. To control train operation, each two-car married-pair had multiple on-board computers communicating with a central computer at Kennedy station. Transit Control at the Hillcrest Complex had a terminal connected to the Kennedy station computer. [2]

Communications-based train control (Lines 1 and 5)

The TTC used "Urbalis 400", a communications-based train control system made by Alstom, on Line 1 Yonge–University. It is engaged in a phased implementation of CBTC to replace the fixed-block signal system on the entire line. CBTC first went live on Line 1 in December 2017 on the newly inaugurated extension between Vaughan Metropolitan Centre station and Sheppard West station. [3] Since then, CBTC has been extended as far as Eglinton station. [4] Effective September 24, 2022, Line 1 had been fully converted to automatic train control (ATC). [1]

CBTC requires a set of equipment on trains and at trackside to gather and transmit data to central computers, and to receive instructions back for train operation. ATC beacons and axle counters sit at track level to detect the passage of a train with the axle counters backing up the beacons. The track-level beacons transmit signals to onboard controllers installed on each train. Onboard roof antennas (Data Communications System antennas) transmit information such as speed and location from the controllers to Trackside Radio Equipment which relays the data to central computers and to the TTC's Transit Control Centre. The central computers send speed and braking instructions back to the train, whereby the central computers are effectively directing each train. With computers operating the train, trains can operate safely on closer headways than with the fixed block system. CBTC allows more frequent service and increased line capacity. [5]

With the old fixed block signal system, the TTC can schedule 25.5 trains per hour on Line 1, occasionally operating up to 29 per hour. With CBTC, the TTC can operate 30 to 32 trains per hour with a more consistent frequency. However, this goal depends on how well the TTC can manage dwell time in stations, crew changeovers and turnaround at terminals. [5] [6]

The grade-separated section of Line 5 Eglinton, between Mount Dennis station and Science Centre station, will also use CBTC. Unlike on Line 1, the system on Line 5 will be supplied by Bombardier Transportation using its Cityflo 650 technology. [7]

The following signal aspects are used with the introduction of CBTC on Line 1: [8] [ better source needed ]

Fixed block signalling (Lines 2 and 4)

As of September 2022, fixed block signalling is used on Line 2 Bloor–Danforth and Line 4 Sheppard, and was used on Line 1 Yonge–University until September 24, 2022. It uses wayside signals to give instructions to train operators, which may be automatic block signals or interlocking signals. This system, also called the NX/UR system of signalling, is also used on the New York City Subway, the Chicago "L", and the MBTA subway in Boston.

Overview

With fixed block signalling, the line is subdivided into blocks – a section of track that can be occupied by a train. Each block is protected by a signal at the start of the block that train operators must obey, with the signal aspects indicating whether it is safe for a train to proceed into the next block. These signals are connected to a trip arm that has the ability to stop a train if it violates a signal (runs a red light), by triggering an emergency brake application. This safety method is identical to that of the New York City Subway system.

If a train is occupying a block, the two or more signals behind the train will be red, with the trip arms in the danger position so that another train cannot proceed into the area. The distance between signals (and number of signals that are red when a particular block is occupied) is set in accordance with the stopping distance required by the trains. If a train violates a signal, the trip arm would trigger an emergency brake application to stop it before it reaches the train ahead. In other words, for a particular signal to clear, the system requires two or more full blocks ahead of that signal must be unoccupied. This requirement reduces the number of trains that can operate on the line compared to using automatic train control. [5]

Grade timing, a method of speed control, is integrated with the signalling system. Station timing signals, which allows trains to safely run closer together at slower speeds (such as near station stops), are also present.

Headway control, a method of evening out the spacing between trains, is active at certain stations with interlocking (or home) signals. [9] Such a signal turns red as a train passes it, and will remain red for a variable amount of time. This time depends on the distance between the last train that passed the signal, and the train that comes after the next train. This system is computerized, and can accurately calculate the relative distances between trains. If the next train is closer to the train before than the train after, then the signal will hold the train at the station. If the next train is closer to the train after it than the train before it, then the signal will clear.

There are several limitations to this signalling system that can result in "signal problems" and "signal delays". One of the most common problems is track down. A track down occurs when a block gets a false reading and places signals into the danger position even when there is no train occupying the block. This can occur if debris interrupts the block by grounding out the track circuit mimicking the electric circuit caused by an actual train in the area.

When a signal fails to clear, depending on the area, there are three different ways to rectify the situation. At some signals, transit control can perform a "call-on" where an orange aspect blinks and the trip arm is released even when the aspect displayed is red. The second option is a "key-by". Some signals have a plunger that the operator can stop, reach out the window, operate the plunger dropping the trip arm and then operate the train to a less restrictive signal. Where neither of these options exist, the only way to get past a defective signal is to "trip through". The operator at slow speed must trip the signal (which in turn trips the train and places it into emergency). The crew must then reset the emergency valve before proceeding.

Block signals

Block signals are the most commonly used signals on the Toronto subway. They are used to keep trains properly spaced, and are controlled automatically by the trains themselves based on their distance relative to other trains, as determined by signal block occupancy. The following block signals are used by the TTC.

A series of block signals south of Yorkdale station. The pictured signals have since been disused after the implementation of CBTC. TTC signal blocks captioned.JPG
A series of block signals south of Yorkdale station. The pictured signals have since been disused after the implementation of CBTC.

Grade timing (GT)

Grade timing (GT) is used to protect sections where a sharp turn requires a speed limit or where a downhill section would cause a train to accelerate to an unsafe speed if the driver were unwary. When entering a signal block which is subject to GT, one of two things controls the signal: the distance to the train ahead, or grade timing. If the current state of the signal is due to proximity of the train ahead, it behaves as a standard block signal. However, once the train ahead has travelled far enough for this signal to clear, the aspect does not immediately change but remains at red. When a train enters the block before the GT signal, a timer is started and the red aspect at the GT signal starts flashing. Once this timer reaches a predetermined time, the signal then clears as normal and the trip arm is lowered. If the train is travelling too fast, it will reach the GT signal before the timer expires and the trip arm will force the train to stop.

The signal at the start of block before a GT signal has an additional white light (termed "lunar aspect" by the TTC) below the other aspects, which illuminates when the following GT signal is at red only due to grade timing. Where there are several consecutive GT signals, a lunar aspect will be present on the signal at the start of each timing block. A flashing red without the lunar aspect (not included in the images above) would be used for the signal at the end of the last block of a GT section.

In addition to lunar white signals, grade timed sections are sometimes indicated by a sign with the letters "GT", or simply "T", in white.

Station timing (ST)

Station timing is used to reduce the separation distance between trains that are operating at slower speeds. It is typically used in and around station platforms, allowing a second train to safely move closer to an already-occupied platform than would otherwise be possible. As with GT signals, a timer is started when a train enters the block preceding the ST signal. If the timer expires before the train reaches the ST signal (i.e. the train is travelling slower than a defined speed), the number of blocks ahead of the ST signal that need to be unoccupied for the signal to clear is reduced. This reflects the shorter braking distance of a train travelling slower than the maximum permitted speed.

Interlocking signals

A TTC interlocking signal TTC interlocking signal.JPG
A TTC interlocking signal

Interlocking signals are typically used in interlockings, which are any areas where train movements may conflict with each other. They are controlled by either human operators or a computer, not automatically by the movement of trains. Interlocking signals also tell train operators which way points are set. The following interlocking signals are used on the TTC.

Interlocking signals can also include grade timing and station timing, which functions in the same way as for block signals. For GT interlocking signals, only the top red aspect will flash while the timer is running, the bottom red aspect remains constantly lit.

Signal numbers

All signals have an alpha-numeric number that relates to their location within the subway system. The number is assigned using the Chain system of measurement, whereby a signal's number is assigned based on the nearest chain measure.

Each line or portion of a line has an assigned letter, and that precedes the number ascertained by the Chain measure. Signals that are on a northbound portion of track use the nearest even valued chain measure, where signals on a southbound portion of track use the nearest odd valued chain measure.

LineSignal prefixEvenOddChain 0 mark
Yonge

(no longer uses block signalling)

N (northbound only, former)
S (southbound only, former)		NorthboundSouthboundDoes not exist (continues from the University numbers)
University

(no longer uses block signalling)

U (former)NorthboundSouthboundSouth of St. George station (counts up towards Museum)
Spadina

(no longer uses block signalling)

SP (former)NorthboundSouthboundNorth of St. George station (counts up towards Spadina station)
Bloor-DanforthBWestboundEastboundWest of Kipling station (counts up towards Islington)
SheppardSHWestboundEastboundWest of Sheppard–Yonge station (counts up towards Bayview)

Temporary signals

In work zones, staff place yellow beacons on the track bed between the rails to inform train operators that a "slow order" is in effect; the first beacon is usually accompanied with a speed restriction sign indicating the speed limit for the affected area. A green beacon indicates the end of a work zone and allows operators to resume normal operation. In outdoor sections, yellow and green flags are also used for the same purpose. A flashing blue light at track level indicates workers may be present, subway operators are required to sound their horn, and follow the signals of track workers when approaching and passing them.

See also

Related Research Articles

<span class="mw-page-title-main">Toronto Transit Commission</span> Agency responsible for local public transit in Ontario, Canada

The Toronto Transit Commission (TTC) is the public transport agency that operates bus, subway, streetcar, and paratransit services in Toronto, Ontario, Canada, some of which run into the Peel Region and York Region. It is the oldest and largest of the urban transit service providers in the Greater Toronto Area, with numerous connections to systems serving its surrounding municipalities.

<span class="mw-page-title-main">Railway signalling</span> The principle of signals used to control railway traffic

Railway signalling (BE), or railroad signaling (AE), is a system used to control the movement of railway traffic. Trains move on fixed rails, making them uniquely susceptible to collision. This susceptibility is exacerbated by the enormous weight and inertia of a train, which makes it difficult to quickly stop when encountering an obstacle. In the UK, the Regulation of Railways Act 1889 introduced a series of requirements on matters such as the implementation of interlocked block signalling and other safety measures as a direct result of the Armagh rail disaster in that year.

<span class="mw-page-title-main">Toronto subway</span> Rapid transit system in Ontario, Canada

The Toronto subway is a rapid transit system serving Toronto and the neighbouring city of Vaughan in Ontario, Canada, operated by the Toronto Transit Commission (TTC). As of September 2023, the subway system is a rail network consisting of three heavy-capacity rail lines operating predominantly underground. As of December 2022, three new lines are under construction: two light rail lines and one light metro line.

<span class="mw-page-title-main">Line 1 Yonge–University</span> Subway line in Toronto, Ontario, Canada

Line 1 Yonge–University is a rapid transit line on the Toronto subway. It serves Toronto and the neighbouring city of Vaughan in Ontario, Canada. It is operated by the Toronto Transit Commission, has 38 stations and is 38.4 km (23.9 mi) in length, making it the longest line on the subway system. It opened as the "Yonge subway" in 1954 as Canada's first underground passenger rail line and was extended multiple times between 1963 and 2017. Averaging over 670,000 riders per weekday, Line 1 is the busiest rapid transit line in Canada, and one of the busiest lines in North America.

<span class="mw-page-title-main">Train stop</span> Railway safety device

Part of a railway signalling system, a train stop, trip stop or tripcock is a train protection device that automatically stops a train if it attempts to pass a signal when the signal aspect and operating rules prohibit such movement, or if it attempts to pass at an excessive speed.

<span class="mw-page-title-main">Automatic train control</span> Class of train protection systems for railways

Automatic train control (ATC) is a general class of train protection systems for railways that involves a speed control mechanism in response to external inputs. For example, a system could effect an emergency brake application if the driver does not react to a signal at danger. ATC systems tend to integrate various cab signalling technologies and they use more granular deceleration patterns in lieu of the rigid stops encountered with the older automatic train stop (ATS) technology. ATC can also be used with automatic train operation (ATO) and is usually considered to be the safety-critical part of a railway system.

<span class="mw-page-title-main">1995 Russell Hill subway accident</span> Deadly Toronto Subway train collision

The 1995 Russell Hill subway accident was a deadly train crash that occurred in Toronto, Ontario, Canada, on Line 1 Yonge–University of the Toronto subway on August 11, 1995. Three people were killed and 30 were taken to hospital with injuries when one train rear-ended another train. The subway line was shut down for five days following the incident. Investigations found that human error and a design flaw in the mechanical safety devices caused this accident. It remains the deadliest accident in a rapid transit system in Canadian history.

Automatic train stop or ATS is a system on a train that automatically stops a train if certain situations occur to prevent accidents. In some scenarios it functions as a type of dead man's switch. Automatic train stop differs from the concept of Automatic Train Control in that ATS usually does not feature an onboard speed control mechanism.

<span class="mw-page-title-main">T series (Toronto subway)</span> Rapid transit rolling stock in service from 1995 to present

The T series, also known as the T-1, is the fourth series of rapid transit rolling stock used in the subway system of Toronto, Ontario, Canada. They were ordered by the Toronto Transit Commission (TTC) in 1992 and built in one production set between 1995 and 2001 by Bombardier Transportation in Thunder Bay, Ontario, Canada.

<span class="mw-page-title-main">UK railway signalling</span> Rail traffic control systems used in the United Kingdom

The railway signalling system used across the majority of the United Kingdom rail network uses lineside signals to control the movement and speed of trains.

Australian railway signalling varies between the States of Australia, because the individual States are responsible for the railway systems within their own borders, with, historically, no need to co-ordinate between states except at the boundaries.

<span class="mw-page-title-main">Signaling of the New York City Subway</span>

Most trains on the New York City Subway are manually operated. As of 2022, the system currently uses automatic block signaling, with fixed wayside signals and automatic train stops. Many portions of the signaling system were installed between the 1930s and 1960s. Because of the age of the subway system, many replacement parts are unavailable from signaling suppliers and must be custom-built for the New York City Transit Authority, which operates the subway. Additionally, some subway lines have reached their train capacity limits and cannot operate extra trains in the current system.

Standards for North American railroad signaling in the United States are issued by the Association of American Railroads (AAR), which is a trade association of the railroads of Canada, the US, and Mexico. Their system is loosely based on practices developed in the United Kingdom during the early years of railway development. However, North American practice diverged from that of the United Kingdom due to different operating conditions and economic factors between the two regions. In Canada, the Canadian Rail Operating Rules (CROR) are approved by the Minister of Transport under the authority of the Railway Safety Act. Each railway company or transit authority in Canada issues its own CROR rulebook with special instructions peculiar to each individual property. Among the distinctions are:

<span class="mw-page-title-main">Washington Metro signaling and operation</span>

Signaling and operation on the Washington Metro system involves train control, station identification, train signaling, signage, and train length. As with any working railroad, communication between train operators, dispatchers, station personnel and passengers is critical. Failures will result in delays, accidents, and even fatalities. It is therefore important that a comprehensive signal system operated by a central authority be in place. This gives individual train and station operators the information they need to safely and efficiently perform their tasks.

<span class="mw-page-title-main">North American railroad signals</span>

North American railroad signals generally fall into the category of multi-headed electrically lit units displaying speed-based or weak route signaling. Signals may be of the searchlight, color light, position light, or color position light types, each displaying a variety of aspects which inform the locomotive operator of track conditions so that they may keep their train under control and able to stop short of any obstruction or dangerous condition.

<span class="mw-page-title-main">Japanese railway signals</span>

Japanese railway signals, according to the ministerial decree defining technical standards of railways, are defined as indicating operational conditions for railway staff driving trains.

<span class="mw-page-title-main">Toronto Rocket</span> Rolling stock of the Toronto subway system

The Toronto Rocket (TR) is the fifth and latest series of rolling stock used in the Toronto subway system in Toronto, Ontario, Canada. Owned and operated by the Toronto Transit Commission (TTC), the trains were built by Bombardier Transportation in Thunder Bay, Ontario, to replace the last remaining H-series trains, as well as increase capacity for the Spadina subway extension to Vaughan that opened in 2017. They operate in a six-car configuration on Line 1 Yonge–University and a four-car configuration on Line 4 Sheppard. The sets are stored and maintained at the Wilson and Davisville Yards. The first six-car TR train entered passenger service on Line 1 in July 2011, and four-car TR trainsets entered service on Line 4 in May 2016.

<span class="mw-page-title-main">Communications-based train control</span> Railway signaling system

Communications-based train control (CBTC) is a railway signaling system that uses telecommunications between the train and track equipment for traffic management and infrastructure control. CBTC allows a train's position to be known more accurately than with traditional signaling systems. This makes railway traffic management safer and more efficient. Metros are able to reduce headways while maintaining or even improving safety.

Modern railway signalling in Thailand on the Mainline employ Color Light Signal and Computer-based interlocking. SRT currently implementing CTC to link whole country signalling system together using Fiber Optic network. This includes Recent Double Tracking Projects for all mainline extend from Bangkok.

References

  1. 1 2 "TTC's Line 1 now running on an ATC signalling system". Toronto Transit Commission. September 29, 2022. Archived from the original on September 29, 2022.
  2. ↑ Bow, James (December 28, 2016). "The Scarborough Rapid Transit Line". Transit Toronto. Retrieved 2017-01-13.
  3. ↑ "Alstoms signalling system equips Toronto subway extension". Alstom. December 18, 2017. Retrieved 9 January 2019.
  4. ↑ "Automatic Train Control – Lessons Learned and Program Update" (PDF). TTC. 8 December 2021. Retrieved 9 January 2022.
  5. 1 2 3 Moore, Oliver (December 22, 2018). "TTC will not complete subway signal-system upgrade by 2019 deadline". The Globe and Mail . Retrieved December 30, 2018.
  6. ↑ Moore, Oliver (June 2, 2017). "Signals from the future: How the TTC's subway auto-pilot will streamline your commute". The Globe and Mail . Retrieved June 2, 2017.
  7. ↑ "Bombardier's Rail Control Division Further Expands North American Presence". Bombardier Transportation. October 8, 2015. Retrieved 9 January 2019.
  8. ↑ iammiroslavglavic (2024-01-28). "what is the meaning of a blinking green light?". r/TTC. Retrieved 2024-03-27.
  9. ↑ "Intermediate Point Headway Control: Questions and Answers". Transit Toronto. Retrieved 2020-10-03.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.