Acoustic Doppler current profiler

Last updated

An acoustic doppler current profiler (ADCP) is a hydroacoustic current meter similar to a sonar, used to measure water current velocities over a depth range using the Doppler effect of sound waves scattered back from particles within the water column. The term ADCP is a generic term for all acoustic current profilers, although the abbreviation originates from an instrument series introduced by RD Instruments in the 1980s. The working frequencies range of ADCPs range from 38  kHz to several megahertz.

Contents

A similar device is a SODAR , which works in the air and uses the same principles for wind speed profiling.

Working principle

ADCPs with three beams resolve the three components of velocity. (Models Aquadopp Profiler 1MHz and 0.6 MHz, Nortek) Z-cell.png
ADCPs with three beams resolve the three components of velocity. (Models Aquadopp Profiler 1MHz and 0.6 MHz, Nortek)
Head of an ADCP with four transducers (Model WH-600, RD Instruments) Adcp 600.jpg
Head of an ADCP with four transducers (Model WH-600, RD Instruments)

ADCPs contain piezoelectric transducers to transmit and receive sound signals. The traveling time of sound waves gives an estimate of the distance. The frequency shift of the echo is proportional to the water velocity along the acoustic path. To measure 3D velocities, at least three beams are required. In rivers, only the 2D velocity is relevant and ADCPs typically have two beams. In recent years, more functionality has been added to ADCPs (notably wave and turbulence measurements) and systems can be found with 2,3,4,5 or even 9 beams.

Further components of an ADCP are an electronic amplifier, a receiver, a clock to measure the traveling time, a temperature sensor, a compass to know the heading, and a pitch/roll sensor to know the orientation. An analog-to-digital converter and a digital signal processor are required to sample the returning signal in order to determine the Doppler shift. A temperature sensor is used to estimate the sound velocity at the instrument position using the seawater equation of state, and uses this to estimate scale the frequency shift to water velocities. This procedure assumes that the salinity has a preconfigured constant value. Finally, the results are saved to internal memory or output online to an external display software.

Underwater photo of an ADCP with five transducers (Model Signature1000, Nortek) Signature1000.jpg
Underwater photo of an ADCP with five transducers (Model Signature1000, Nortek)

Processing methods

Three common methods are used to calculate the Doppler shift and thus the water velocity along the acoustic beams. The first method uses a monochromatic transmit pulse and is referred to as "incoherent" or "narrowband". The method is robust and provides good quality mean current profiles but has limited space-time resolution. When the transmit pulse consists of coded elements that are repeated, the method is referred to as "repeat sequence coding" [1] or "broadband". This method improves the space-time resolution by a factor of 5 (typical). Commercially, this method was protected by US patent [2] 5615173 until 2011. The pulse-to-pulse coherent method [3] relies on a sequence of transmit pulses where the echo from subsequent pulses are assumed not to interfere with each other. This method is only applicable for very short profiling ranges but the corresponding improvement in space time resolution is of order 1000.

Applications

Depending on the mounting, one can distinguish between side-looking, downward- and upward-looking ADCPs. A bottom-mounted ADCP can measure the speed and direction of currents at equal intervals all the way to the surface. Mounted sideways on a wall or bridge piling in rivers or canals, it can measure the current profile from bank to bank. In very deep water they can be lowered on cables from the surface.

The primary usage is for oceanography. [4] The instruments can also be used in rivers and canals to continuously measure the discharge.

Mounted on moorings within the water column or directly at the seabed, water current and wave studies may be performed. They can stay underwater for years at a time, the limiting factor is the lifetime of the battery pack. Depending on the nature of the deployment the instrument usually has the ability to be powered from shore, using the same umbilical cable for data communication. Deployment duration can be extended by a factor of three by substituting lithium battery packs for the standard alkaline packs.

Bottom tracking

By adjusting the window where the Doppler shift is calculated, it is possible to measure the relative velocity between the instrument and the bottom. This feature is referred to as bottom-track. The process has two parts; first identify the position of the bottom from the acoustic echo, then calculating the velocity from a window centered around the bottom position. When an ADCP is mounted on a moving ship, the bottom track velocity may be subtracted from the measured water velocity. The result is the net current profile. Bottom track provides the foundation for surveys of the water currents in coastal areas. In deep water where the acoustic signals cannot reach the bottom, the ship velocity is estimated from a more complex combination of velocity and heading information from GPS, gyro, etc.

Discharge measurements

In rivers, the ADCP is used to measure the total water transport. The method requires a vessel with an ADCP mounted over the side to cross from one bank to another while measuring continuously. Using the bottom track feature, the track of the boat as well as the cross sectional area is estimated after adjustment for left and right bank areas. The discharge can then be calculated as the dot product between the vector track and the current velocity. The method is in use by hydrographic survey organisations across the world and forms an important component in the stage-discharge curves used in many places to continuously monitor river discharge.

Doppler velocity log (DVL)

For underwater vehicles, the bottom tracking feature can be used as an important component in the navigation systems. In this case the velocity of the vehicle is combined with an initial position fix, compass or gyro heading, and data from the acceleration sensor. The sensor suite is combined (typically by use of a Kalman filter) to estimate the position of the vehicle. This may help to navigate submarines, autonomous, and remotely operated underwater vehicles.

The AWAC (Acoustic Wave and Currents) is a type of ADCP specifically designed for surface wave height and direction. Bo-awac+frame91.jpg
The AWAC (Acoustic Wave and Currents) is a type of ADCP specifically designed for surface wave height and direction.

Wave measurements

Some ADCPs can be configured to measure surface wave height and direction. The wave height is estimated with a vertical beam that measures the distance to the surface using the echo from short pulses and simple peak estimation algorithms. The wave direction is found by cross correlating the along-beam velocity estimates and the wave height measurement from the vertical beam. Wave measurements are typically available for seafloor-mounted instruments but recent improvements permit the instrument to be mounted also on rotating subsurface buoys. [5]

Turbulence

ADCPs with pulse-to-pulse coherent processing can estimate the velocity with the precision required to resolve small scale motion. As a consequence, it is possible to estimate turbulent parameters from properly configured ADCPs. A typical approach is to fit the along beam velocity to the Kolmogorov structure configuration and thereby estimate the dissipation rate. The application of ADCPs to turbulence measurement is possible from stationary deployments but can also be done from moving underwater structures like gliders or from subsurface buoys.

Advantages and disadvantages

The two major advantages of ADCPs is the absence of moving parts that are subject to biofouling and the remote sensing aspect, where a single, stationary instrument can measure the current profile over ranges exceeding 1000 m. These features allow for long term measurements of the ocean currents over a significant portion of the water column. Since the start in the mid-1980s, many thousand ADCPs have been used in the world oceans and the instrument has played a significant role in our understanding of the world ocean circulation.

The main disadvantage of the ADCPs is the loss of data close to the boundary. This mechanism, often referred to as a sidelobe interference, covers 6–12% of the water column and, for instruments looking up toward the surface, the loss of velocity information close to the surface is a real disadvantage. Cost is also a concern but is normally dwarfed by the cost of the ship required to ensure a safe and professional deployment.

As any acoustical instrument, the ADCP contributes to noise pollution in the ocean which may interfere with cetacean navigation and echolocation. [6] The effect depends on the frequency and the power of the instrument but most ADCPs operate in a frequency range where noise pollution has not been identified to be a serious problem.

Related Research Articles

<span class="mw-page-title-main">Anemometer</span> Instrument for measuring wind speed

In meteorology, an anemometer is a device that measures wind speed and direction. It is a common instrument used in weather stations. The earliest known description of an anemometer was by Italian architect and author Leon Battista Alberti (1404–1472) in 1450.

The Doppler effect is the change in the frequency of a wave in relation to an observer who is moving relative to the source of the wave. The Doppler effect is named after the physicist Christian Doppler, who described the phenomenon in 1842. A common example of Doppler shift is the change of pitch heard when a vehicle sounding a horn approaches and recedes from an observer. Compared to the emitted frequency, the received frequency is higher during the approach, identical at the instant of passing by, and lower during the recession.

<span class="mw-page-title-main">Sonar</span> Acoustic sensing method

Sonar is a technique that uses sound propagation to navigate, measure distances (ranging), communicate with or detect objects on or under the surface of the water, such as other vessels.

<span class="mw-page-title-main">Wind speed</span> Rate at which air moves from high- to low-pressure areas

In meteorology, wind speed, or wind flow speed, is a fundamental atmospheric quantity caused by air moving from high to low pressure, usually due to changes in temperature. Wind speed is now commonly measured with an anemometer.

<span class="mw-page-title-main">Echo sounding</span> Measuring the depth of water by transmitting sound waves into water and timing the return

Echo sounding or depth sounding is the use of sonar for ranging, normally to determine the depth of water (bathymetry). It involves transmitting acoustic waves into water and recording the time interval between emission and return of a pulse; the resulting time of flight, along with knowledge of the speed of sound in water, allows determining the distance between sonar and target. This information is then typically used for navigation purposes or in order to obtain depths for charting purposes.

<span class="mw-page-title-main">Millimeter cloud radar</span> Weather radar tuned to cloud detection

Millimeter-wave cloud radars, also denominated cloud radars, are radar systems designed to monitor clouds with operating frequencies between 24 and 110 GHz. Accordingly, their wavelengths range from 1 mm to 1.11 cm, about ten times shorter than those used in conventional S band radars such as NEXRAD.

<span class="mw-page-title-main">Stream gauge</span> Location used to monitor surface water flow

A stream gauge, streamgage or stream gauging station is a location used by hydrologists or environmental scientists to monitor and test terrestrial bodies of water. Hydrometric measurements of water level surface elevation ("stage") and/or volumetric discharge (flow) are generally taken and observations of biota and water quality may also be made. The locations of gauging stations are often found on topographical maps. Some gauging stations are highly automated and may include telemetry capability transmitted to a central data logging facility.

Flow measurement is the quantification of bulk fluid movement. Flow can be measured using devices called flowmeters in various ways. The common types of flowmeters with industrial applications are listed below:

<span class="mw-page-title-main">Time of flight</span> Timing of substance within a medium

Time of flight (ToF) is the measurement of the time taken by an object, particle or wave to travel a distance through a medium. This information can then be used to measure velocity or path length, or as a way to learn about the particle or medium's properties. The traveling object may be detected directly or indirectly. Time of flight technology has found valuable applications in the monitoring and characterization of material and biomaterials, hydrogels included.

<span class="mw-page-title-main">Bathymetry</span> Study of underwater depth of lake or ocean floors

Bathymetry is the study of underwater depth of ocean floors, lake floors, or river floors. In other words, bathymetry is the underwater equivalent to hypsometry or topography. The first recorded evidence of water depth measurements are from Ancient Egypt over 3000 years ago.

<span class="mw-page-title-main">Laser Doppler velocimetry</span> Optical method of measuring fluid flow

Laser Doppler velocimetry, also known as laser Doppler anemometry, is the technique of using the Doppler shift in a laser beam to measure the velocity in transparent or semi-transparent fluid flows or the linear or vibratory motion of opaque, reflecting surfaces. The measurement with laser Doppler anemometry is absolute and linear with velocity and requires no pre-calibration.

<span class="mw-page-title-main">Ultrasonic flow meter</span> Flow meter using ultrasound

An ultrasonic flow meter is a type of flow meter that measures the velocity of a fluid with ultrasound to calculate volume flow. Using ultrasonic transducers, the flow meter can measure the average velocity along the path of an emitted beam of ultrasound, by averaging the difference in measured transit time between the pulses of ultrasound propagating into and against the direction of the flow or by measuring the frequency shift from the Doppler effect. Ultrasonic flow meters are affected by the acoustic properties of the fluid and can be impacted by temperature, density, viscosity and suspended particulates depending on the exact flow meter. They vary greatly in purchase price but are often inexpensive to use and maintain because they do not use moving parts, unlike mechanical flow meters.

<span class="mw-page-title-main">Sodar</span> Meteorological instrument

Sodar, an acronym of sonic detection and ranging, is a meteorological instrument used as a wind profiler based on the scattering of sound waves by atmospheric turbulence. Sodar equipment is used to measure wind speed at various heights above the ground, and the thermodynamic structure of the lower layer of the atmosphere.

<span class="mw-page-title-main">Underwater acoustics</span> Study of the propagation of sound in water

Underwater acoustics is the study of the propagation of sound in water and the interaction of the mechanical waves that constitute sound with the water, its contents and its boundaries. The water may be in the ocean, a lake, a river or a tank. Typical frequencies associated with underwater acoustics are between 10 Hz and 1 MHz. The propagation of sound in the ocean at frequencies lower than 10 Hz is usually not possible without penetrating deep into the seabed, whereas frequencies above 1 MHz are rarely used because they are absorbed very quickly.

<span class="mw-page-title-main">Coastal ocean dynamics applications radar</span>

Coastal ocean dynamics applications radar (CODAR) is a type of portable, land-based, high frequency (HF) radar developed between 1973 and 1983 at NOAA's Wave Propagation Laboratory in Boulder, Colorado. CODAR is a noninvasive system that can measure and map near-surface ocean currents in coastal waters. It is transportable and can produce ocean current maps on site in near real time. Moreover, using CODAR it is possible to measure wave heights and produce an indirect estimate of local wind direction.

<span class="mw-page-title-main">Wave radar</span> Technology for measuring surface waves on water

Wave radar is a type of radar for measuring wind waves. Several instruments based on a variety of different concepts and techniques are available, and these are all often called. This article, gives a brief description of the most common ground-based radar remote sensing techniques.

<span class="mw-page-title-main">Laser Doppler vibrometer</span> Instrument for sensing microscopic vibrations of a surface

A laser Doppler vibrometer (LDV) is a scientific instrument that is used to make non-contact vibration measurements of a surface. The laser beam from the LDV is directed at the surface of interest, and the vibration amplitude and frequency are extracted from the Doppler shift of the reflected laser beam frequency due to the motion of the surface. The output of an LDV is generally a continuous analog voltage that is directly proportional to the target velocity component along the direction of the laser beam.

<span class="mw-page-title-main">Current meter</span> Device for measuring the flow in a water current

A current meter is an oceanographic device for flow measurement by mechanical, tilt, acoustical or electrical means.

A vector measuring current meter (VMCM) is an instrument used for obtaining measurements of horizontal velocity in the upper ocean, which exploits two orthogonal cosine response propeller sensors that directly measure the components of horizontal velocity. VMCM was developed in the late 1970s by Drs. Robert Weller and Russ Davis and commercially produced by EG&G Sealink System . The instrument has the capability of one year long deployment at depths of up to 5000 m. Both laboratory and field test results show that the VMCM is capable of making accurate measurements of horizontal velocity in the upper ocean. The VMCM is the current standard for making high quality velocity measurements in near-surface regions and it has been used for benchmarking other current meters.

<span class="mw-page-title-main">Underwater survey</span> Inspection or measurement in or of an underwater environment

An underwater survey is a survey performed in an underwater environment or conducted remotely on an underwater object or region. Survey can have several meanings. The word originates in Medieval Latin with meanings of looking over and detailed study of a subject. One meaning is the accurate measurement of a geographical region, usually with the intention of plotting the positions of features as a scale map of the region. This meaning is often used in scientific contexts, and also in civil engineering and mineral extraction. Another meaning, often used in a civil, structural, or marine engineering context, is the inspection of a structure or vessel to compare actual condition with the specified nominal condition, usually with the purpose of reporting on the actual condition and compliance with, or deviations from, the nominal condition, for quality control, damage assessment, valuation, insurance, maintenance, and similar purposes. In other contexts it can mean inspection of a region to establish presence and distribution of specified content, such as living organisms, either to establish a baseline, or to compare with a baseline.

References

  1. "Repeat-Sequence Coding for Improved Precision of Doppler Sonar and Sodar, R. Pinkel and J. A. Smith". Journal of Atmospheric and Oceanic Technology. 9: 149. 1992. doi: 10.1175/1520-0426(1992)009<0149:RSCFIP>2.0.CO;2 . ISSN   1520-0426.
  2. "Acoustic doppler current profiler, US Patent 5615173".
  3. "Pulse-to-Pulse Coherent Doppler Sonar Signal Processing Techniques, Roger Lhermitte". Journal of Atmospheric and Oceanic Technology. 1: 293. 1984. doi: 10.1175/1520-0426(1984)001<0293:PTPCDS>2.0.CO;2 . ISSN   1520-0426.
  4. William J. Emery, Richard E. Thomson (2001). Data analysis methods in physical oceanography. Gulf Professional Publishing. p. 83. ISBN   978-0-444-50757-0 . Retrieved 2011-02-06.
  5. "System and method for determining directional and non-directional fluid wave and current". US Patent office.
  6. Hogan, C Michael (October 2011). "Icon Encyclopedia of Earth Topics". Washington, D.C.: Environmental Information Coalition, National Council for Science and the Environment. Retrieved 2012-09-13.