In March 2005, United States House Commerce Committee chairman Joe Barton of Texas said he would introduce a bill requiring the transition to digital television "sometime in the spring", saying he wanted analog broadcasting to end on December 31, 2006. Included in his plan was a $400–$500 million subsidy for converter boxes, which were expected to cost $50 each. The subsidies were intended only for people who could not afford a pay service such as cable or satellite television. Each home would receive a rebate coupon for one box, which could be mailed to the United States Treasury for redemption. Barton estimated that 8 to 10 million converters would be needed.[1]
Digital Transition and Public Safety Act of 2005
The United States Digital Transition and Public Safety Act of 2005, part of the Deficit Reduction Act of 2005, required that the Federal Communications Commission (FCC) direct all full-power television stations to cease analog TV broadcasting before midnight on February 17, 2009. (This deadline later changed to June 12.) Recognizing that consumers might wish to continue receiving broadcast programming over-the-air using analog-only televisions, the Act authorized the NTIA to create a digital-to-analog converter box assistance program. Consumer education plans for the subsidy program were targeted to low-income, elderly, disabled, inner city, immigrant, and rural Americans, because these groups were more likely to use an antenna instead of cable or satellite television.[2] The Act also established a new Treasury fund, known as the Digital Television Transition and Public Safety Fund. It directed the FCC to deposit the receipts from the spectrum auction of the returned analog television frequencies into the fund.
The Act directed the NTIA to implement and administer a program through which eligible US households could obtain a maximum of two "coupons" (actually paymentvouchers) of $40 each, to be applied towards the purchase of a digital-to-analog converter box. The Act defines the term converter box to mean "a stand-alone device that does not contain features or functions except those necessary to enable a consumer to convert any channel broadcast in the digital television service into a format that the consumer can display on television receivers designed to receive and display signals only in the analog television service, but may also include a remote control device." The Act, however, did not define "eligible household".[3]
As of April 2006, 20 million people (some with more than one set) received only over-the-air TV. When the number of people subscribing to cable or satellite who also had TVs that only used an antenna, an estimated 70 million TVs would need upgrading.[4]
Implementing the program
In 2006, the NTIA let people see its plan for distributing coupons and comment on it. The plan prohibited people with cable or satellite service from requesting coupons. In order to get two coupons, consumers had to state that they had two television sets. In an effort to limit misconduct, coupon requests would be only be taken between January 1, 2008 and March 31, 2009; each coupon would be valid for three months. The consumer-education program only had a budget of $5 million, so the companies participating in the transition would have to help.[5]
On March 12, 2007, the NTIA held a news conference to announce the standards for the converter boxes and the requirements for receiving coupons. With the standards established, manufacturing could begin and the NTIA could select a company to send out coupons.[6]
With $1.5 billion in funding, the coupons would account for only half of the 73 million analog TVs not using a pay service, including 18 million in homes having only over-the-air TV reception. The Commerce Department had no plans to make coupons available only to the poor.
Coupons could be requested by phone, mail, or online.[7] At first, anyone would be able to apply, even for those who had one or more TVs connected to cable or satellite.
The NTIA set the standards for the converter box based on what manufacturers and broadcasters wanted. LG Electronics, Thomson, Samsung, and Jasco were the first companies to announce plans to make the devices. After June 1, 2007, retailers could apply to sell converter boxes. Each would have to be in the NTIA's Central Contractor Registration database, and have been in the consumer-electronics business for at least a year.[8]
An example of the NTIA converter box $40 subsidy "coupon", which is in the form of a bank card that can only be used as payment for a converter box purchase.
To implement the coupon program, the Act authorized NTIA to use up to $990 million from the fund, including $100 million for program administration. Those funds supported an initial "non-contingent" program that was available to all requesting households. NTIA was also authorized to spend up to $1.5 billion for the program (including $160 million for administration) if the initial $990 million were insufficient to fulfill the non-contingent coupon requests. In that case, a "contingent" fund would be available for US households not serviced by cable or satellite.[9] If the funds were insufficient, the Committee on Energy and Commerce of the House of Representatives and the Committee on Commerce, Science, and Transportation of the Senate would be notified.
An initial funding of $990 million was expected to allow all US households an opportunity to apply for the coupons, which expired 90 days after they were mailed. After that money was used up, $510 million in additional funds was available to households that stated they did not already subscribe to cable or satellite television services. Neither allotment had a means test.[9]
The NTIA planned to start processing coupon requests a year before the original transition date of February 17, 2009; 2.4 million people had applied for 4.7 million coupons, out of an estimated 13 million homes that still received television with an antenna.[10]
By the end of 2008, the New York Times said "about 40 million coupons have been requested, but to date 16 million have been redeemed, compared with an estimated 35 million televisions that will lose a signal."[11] Institutions, such as retirement homes, were initially excluded from the program; while this was partially remedied (to allow one coupon per retirement-home resident),[citation needed] prisons,[12] homeless shelters[13] and residential hotels remained disqualified from the coupon program.
On January 4, 2009, the NTIA began placing coupon requests on a waiting list after the program reached its maximum allowed funding. Only after unredeemed coupons expire could new requests be fulfilled.[14] By January 7, NTIA's waiting list included just under a million requested coupons. A week later, the list had grown to two million coupons.[15] On January 7, both Consumers Union and Representative Ed Markey of Massachusetts (who headed the U.S. HouseEnergy and Commerce Committee’s telecom subcommittee) advocated that the February 17, 2009 analog shutoff date be postponed, due to the lack of coupons and NTIA's inability to handle the expected public enquiries.[16] On January 8, President-Elect Barack Obama's transition team contacted key legislators to express support for a delay, largely because of problems funding coupons for converters.[17][18] The delay passed early in February (see below).
Specifications
The NTIA Specification is arranged in three categories, describing required, permitted, and disqualifying features.
Absolute requirements
A digital TV converter box
The following features were required, but could be provided by the box in various ways.
Coupon-eligible converter boxes had to convert all ATSC (digital) formats to the traditional NTSC analog system used by analog US television sets. The box needed to output radio frequency signals (compatible with a television's antenna input), composite video, and stereo audio. It had to include a remote control, and be compatible with universal remotes.
The units had to support both a 4:3 center crop of a 16:9 transmitted image, and a letterboxed rendition of a 16:9 transmitted image. The video outputs had to produce video at an ITU-R BT.500-11 quality scale of Grade 4 or higher. Various technical performance parameters for the digital tuner were also specified.
CECBs could not consume more than an average of 2 watts of power when not in use (when there was no video or audio display). They had to provide an automatic power-down option that could put the unit in standby mode when it hadn't received any commands for a period of time.
Optional features
Manufacturers could self-certify compliance with these requirements, but had to provide test results and two units to the NTIA for ad hoc testing. The FCC could also test converter boxes at the NTIA's request. Among the optional features permitted, but not required, were the following:
Support for a smart antenna, through the use of the CEA-909 Antenna Control Interface. The manufacturer could optionally provide a promotional package discount for the combination of a smart antenna and a CECB.
While an outdoor antenna is required for adequate digital reception in most locations beyond 10–25 miles (16–40km) from TV transmitters, and smart antenna interfaces were an optionally permitted feature of coupon-eligible converter boxes,[20] there were no subsidies for antennas. Although manufacturers could sell a converter/smart-antenna bundle, they were required to also offer the converter by itself to consumers.[21]
Some features disqualified a converter box from coupon eligibility, such as high-definition video output and built-in DVR functionality. Digital cable and satelliteset-top boxes that incorporate a digital tuner were also disqualified.
Coupon-eligible converter boxes only tune to one channel at a time, as they only contain one digital tuner and no analog tuner. In order to watch one channel while recording another, one must have two such converter boxes, unless the recording device has its own digital TV tuner.
Most video recorders were also unable to change channels under control of built-in timers when using a converter, as channel selection was then handled by the converter.[23] Some converter boxes have a programmable timer, which the user could program to match the recording schedule of their VCR. Then, the converter's tuner will change to the appropriate channel at the time the VCR needs to record. This requires a separate box for the VCR, or the viewer will have to watch what is being recorded. Another, less common option is an "IR blaster", which a recorder can use to control an external tuner, like a cable set-top box or converter box. However, older devices with IR blasters may not be fully compatible with digital subchannels; the converter box may require the use of a [-] or [.] button to specify the subchannel, which the pre-digital recorder may not know how to transmit. Some older TiVo brand digital recorders received software updates specifically to control digital converter boxes via the TiVo's included IR blaster.[24]
Small battery-operated portable televisions, while valuable in time of disaster, are generally poorly suited to digital conversion. While at least one CECB (Winegard's RCDT09A) is operable from an external battery pack,[25] the combination of television, converter, external antenna, and power supply limits portability.[26]As of 2009[update], portable digital LCDTV sets cost at least $100, and could not be used while in motion at significant speeds (restoring this analog functionality would require broadcasters to transmit mobile TV via the separate ATSC-M/H standard, which would in itself require new tuners).
The inability of some boxes to add new digital channels without a full re-scan—deleting all existing channel settings—renders them unusable to viewers who rely on directional antennas and rotors to receive distant stations. Signal strength meters, where available, are awkward, typically only displaying information for channels that have already been found.[27] This is problematic, as digital signals are most often transmitted on higher frequencies or with far less power than their analog counterparts,[28] requiring careful antenna installation, orientation and location to avoid obstructions, fading and multipath interference problems. Where the converter fails to receive a channel, an often-cumbersome manual process is usually provided; however, this requires knowledge of which frequencies each missing station is actually transmitting on, rather than the virtual channels each is mapped to by the ATSC protocol.
Since the NTIA did not require CECBs to output MTS stereo signals via their radio-frequency output, THAT Corporation[lower-alpha 1] noted that consumers using RF-only connections with CECBs will lose stereo TV sound.[29] This problem may be avoided by using the converter's line level audio outputs.
Low-power television concerns
A year before the transition, Ron Bruno, president of the Community Broadcasters Association (CBA), said only four of 37 NTIA-certified converter boxes had analog passthrough, and none had analog tuners.[10]
In late March 2008, the CBA filed a lawsuit in the U.S. Court of Appeals for the District of Columbia seeking an injunction to halt the sale and distribution of CECBs.[30][31] According to the CBA, the converters' lack of support for analog transmissions would harm its member stations, which include low-power and class A television stations, as it was cost-prohibitive for many of them to convert to digital transmission.[32] The CBA claimed that the new boxes would prevent viewers from being able to watch these analog-only stations; viewers might not even be aware such stations still existed, because the boxes would not list them.[33] At the time of the digital transition, the FCC did not set a deadline for existing LPTV stations to convert to digital service; however, it announced that no new analog LPTV stations would be authorized.[34]
Responding to the CBA, the FCC and NTIA urged manufacturers to include analog support voluntarily in all converter boxes. Manufacturers responded by releasing a new generation of models with the feature. Some new DVD recorders and personal video recorders also provide both analog and digital tuners, and therefore could perform the basic functions of a set-top box in both modes.
In early May 2008, the D.C. district court denied the CBA petition without comment. The CBA felt that the court wanted them to continue working with the FCC. The association said it would continue to pressure the FCC to support analog functionality as a requirement of the All-Channel Receiver Act, urge more government funding for low power and Class A broadcasters to transition to digital, and ask Congress to increase the number of such stations eligible for funds.[35]
On August 13, 2009, the CBA announced that it would cease operations. One reason given was the cost required to fight "restrictive regulations that kept the Class A and LPTV industry from realizing its potential", including the campaign to require analog passthrough. Amy Brown, former CBA executive director, said "some 40 percent of Class A and LPTV station operators believe they will have to shut down in the next year if they are not helped through the digital transition."[36]
In June 2010, the FCC stopped accepting new applications for digital LPTV stations while it considered the spectrum needs of the National Broadband Plan.[37] In a Notice of Proposed Rulemaking published in September 2010, the FCC suggested setting a shutoff date for all analog TV transmissions, including LPTV stations, in 2012.[38] It also proposed moving all low-power stations on channels 52–69 to new frequencies, to free the 700MHz band for other uses.[38] In April 2011, the NTIA announced that it would stop accepting applications for grants toward upgrading LPTV stations to digital transmission as of July 2, 2012.[39] The grant program was initially funded with $44 million; as of June2011[update], over $30 million in grant funding remained available.[40]
The final deadline for LPTV Shutdown is 1 September 2015. The last NTIA grants offered to LPTV Broadcasters/Repeaters to convert their systems to digital ended in July 2012. The September 2015 deadline is to allow for possible new construction to accommodate digital equipment.[41] Unlike the TV Full-Power Transmitter Digital Conversion in 2009, there will be no consumer subsidy program for the final LPTV digital conversion deadline since it is anticipated that without DTV Set-Top Converter Boxes, the majority of remaining SDTV/EDTV models in use should have left the consumer market by then.
End of subsidies
By early January 2009, the NTIA had issued $1.34 billion worth of coupons for converter boxes, reaching the obligation limit set by the U.S. Congress in the Digital Television Transition and Public Safety Act of 2005. As a result, the NTIA started placing requests for coupons on a waiting list, issuing coupons as previously-issued but unredeemed coupons reached their expiration date.[42]
In December 2008, FCC commissioner McDowell urged "those who don't need the government subsidy not to wait on that process before purchasing a converter box for themselves or as a gift for someone else. During the weeks it takes for the government to process coupon requests, you will lose precious time to hook up the box, check antenna connections, and start enjoying free digital broadcast TV right away."[43]
Nielsen Media Research estimated in August 2008 that 25 percent of affected viewers would opt for inexpensive converters instead of replacing existing televisions or switching to cable and satellite television subscriptions.[citation needed] By November 2008, 38.3 percent were planning to buy the less-costly converter boxes.[citation needed]
Many retailers had stocked converters based on coupon use and shortages of the converter boxes themselves remained possible.[44] In early February 2009, the Consumer Electronics Association estimated that three to six million converters were available,[45] while Nielsen estimated 5.8 million American households were completely unready for digital transition.[citation needed] The New York Times estimated that converter supplies could run out by the end of the month.[46] Manufacturers who had halted production ahead of the original February 17, 2009 deadline were to resume converter box assembly but this new stock was not expected in stores until April.[47]
Legislators from the American southwest were among those supporting a delay in the digital cutover, citing safety concerns because as many as a quarter of households in television markets there had not prepared to receive digital signals by January 2009. A judge from Hildago County, Texas noted that Latino, low-income, elderly, and rural homes were at risk.[48] Some residents could receive analog signals from Mexico;[48] Mexico did not transition to digital transmission until the end of 2015.
DTV Delay Act
The DTV Delay Act, signed into law on February 11, 2009, extended the digital transition deadline to June 12, 2009.[49][50] The DTV Delay Act did not address the shortfall in funding for converter-box coupons; the American Recovery and Reinvestment Act, part of a larger appropriations bill signed into law on February 17, 2009, added $650 million in funding—$490 million of that for coupons, increasing the total coupon-fund expenditure to $1.83 billion.[51][52][53] By February 18, 36 percent of the United States's full-power stations had transitioned to digital-only, but five million of the nation's 115 million households remained entirely unready;[54] at the time, 4.3 million coupon requests remained on the NTIA waiting list.[15] The NTIA resumed issuing coupons in early March 2009, expecting to clear its backlog in two and a half weeks.[55] Political issues had contributed to the delays in sending out coupons; the NTIA could not issue coupons above the spending limit set in the bill, even knowing that many already-issued coupons would expire.[56] Even though unused coupons meant more money for the program, the coupons had to actually expire before the money could be "reused" for newly issued coupons.[57] Those coupons it did send out were sent via standard mail, rather than first-class mail, as Congress had required in the legislation, but that caused coupons to be delayed up to four weeks.[56]
The NTIA was legally required to issue coupons on a first-come, first-served basis; viewers in markets where individual stations ended analog broadcasts by the original deadline did not receive priority handling of their DTV coupon requests.[58]
On March 24, 2009, the NTIA announced that the four-million-person waiting-list backlog had been cleared, meaning those whose coupons had expired could reapply. The NTIA estimated 17 million coupons had expired, while 25.7 million—56 percent of those issued—had been used.[52] On April 12, Nielsen estimated that 3.6 million households remained unready.[59]
Completing the transition
The analog shutdown for full-power TV stations was completed in mid-2009, with several stations ending analog transmissions well before the June 12, 2009 deadline. (Many transitioned on the original February 17 date.) In most cases, at least one station in each media market continued analog broadcasts for up to 30 days afterward as an "analog nightlight"—prohibited from broadcasting regular programming, but allowed to transmit information on how to obtain and connect a converter box to receive digital programming (and send Emergency Alert System broadcasts.). This allowed viewers who had not converted by the deadline to receive at least one channel that would explain the absence of the other analog channels. The half-hour public service announcement with English and Spanish segments seen on most such stations was produced by the National Association of Broadcasters.[citation needed]
Nielsen said 2.5 million homes were still incapable of receiving a digital signal two days after the deadline.[60] On June 17, 2009, the NTIA said two million requested coupons had not yet been mailed.[60]
The NTIA reported that, as of July 22, 2009, 33,578,000 coupons had been used—more than the 33.5 million possible with the original $1.34 billion allocation. $435 million of the extra money added was already owed for pending requests.[53]
U.S. Representative Peter DeFazio and Senator Bernie Sanders introduced legislation which would have extended the converter-box coupon program beyond July 31, 2009, subsidized antennas, and require satellite and cable TV companies to provide a $10 basic-broadcast-channel package available to those who had lost the ability to receive at least one over-the-air channel because of the transition.[61] Neither Congressman's bill was passed into law.[62][63]
At midnight on July 31, 2009, the CECB program expired, without extension.[citation needed] Toward the end of July, consumers were making 35,000 requests for coupons per day, with just over half those issued being used.[64] On July 30, though, the number of requests totalled 78,000, and on the final day, 169,000 were received.[65] Requests sent via mail with a postmark of July 31 or earlier were processed; about $300 million in funding remained. By August 5, 2009, consumers had used 33,962,696 coupons.[65]
The NTIA said 4,287,379 coupons had been requested but not redeemed. As of August 12, $310,796,690 was available, and if all requested coupons were redeemed, $139,300,174 would be left.[57]
An unidentified NTIA source said the agency returned $241.6 million to the Treasury Department; $2.6 million went to "final closeout costs".[66] After the program ended, $250 million from the original bill had not been used, and the additional $490 million allocated in February 2009 had not been touched.[66] These funds almost equalled the $490 million Congress had appropriated to boost the program in January 2008, when it appeared the program would run out of money.[66] The additional funding was needed to satisfy the accounting rules imposed on the program by Congress, rather than an actual need for the funds.[66] The unused funds from the original bill went to a DTV public safety fund, as required in the legislation.[66]
Notes
↑ Which licensed the now-expired patents to the dbx noise reduction technology used in MTS, and still holds patents on some digital implementations of MTS
Related Research Articles
Digital television (DTV) is the transmission of television signals using digital encoding, in contrast to the earlier analog television technology which used analog signals. At the time of its development it was considered an innovative advancement and represented the first significant evolution in television technology since color television in the 1950s. Modern digital television is transmitted in high-definition television (HDTV) with greater resolution than analog TV. It typically uses a widescreen aspect ratio in contrast to the narrower format (4:3) of analog TV. It makes more economical use of scarce radio spectrum space; it can transmit up to seven channels in the same bandwidth as a single analog channel, and provides many new features that analog television cannot. A transition from analog to digital broadcasting began around 2000. Different digital television broadcasting standards have been adopted in different parts of the world; below are the more widely used standards:
The All-Channel Receiver Act of 1962 (ACRA), commonly known as the All-Channels Act, was passed by the United States Congress in 1961, to allow the Federal Communications Commission to require that all television set manufacturers must include UHF tuners, so that new UHF-band TV stations could be received by the public. This was a problem at the time since most affiliated stations of the Big Three television networks were well-established on VHF, while many local-only stations on UHF were struggling for survival.
WOCH-CD was a low-power, Class A television station in Chicago, Illinois, United States. The station was owned by NRJ TV, LLC.
The class A television service is a system for regulating some low-power television (LPTV) stations in the United States. Class A stations are denoted by the broadcast callsign suffix "-CA" (analog) or "-CD" (digital), although very many analog -CA stations have a digital companion channel that was assigned the -LD suffix used by regular (non-class-A) digital LPTV stations.
An ATSCtuner, often called an ATSC receiver or HDTV tuner, is a type of television tuner that allows reception of digital television (DTV) television channels that use ATSC standards, as transmitted by television stations in North America, parts of Central America, and South Korea. Such tuners are usually integrated into a television set, VCR, digital video recorder (DVR), or set-top box which provides audio/video output connectors of various types.
WJFB is a television station licensed to Lebanon, Tennessee, United States, broadcasting the classic television network MeTV to the Nashville area. Owned and operated by Weigel Broadcasting, the station maintains transmitter facilities in Whites Creek, Tennessee, just off I-24 and Old Hickory Boulevard.
Mobile television is television watched on a small handheld or mobile device, typically developed for that purpose. It includes service delivered via mobile phone networks, received free-to-air via terrestrial television stations, or via satellite broadcast. Regular broadcast standards or special mobile TV transmission formats can be used. Additional features include downloading TV programs and podcasts from the Internet and storing programming for later viewing.
A digital channel election was the process by which television stations in the United States chose which physical radio-frequency TV channel they would permanently use after the analog shutdown in 2009. The process was managed and mandated by the Federal Communications Commission for all full-power TV stations. Low-powered television (LPTV) stations are going through a somewhat different process, and are also allowed to flash-cut to digital.
A digital television adapter (DTA), commonly known as a converter box or decoder box, is a television tuner that receives a digital television (DTV) transmission, and converts the digital signal into an analog signal that can be received and displayed on an analog television set. Some also have an HDMI output since some TVs with HDMI do not have a digital tuner. The input digital signal may be over-the-air terrestrial television signals received by a television antenna, or signals from a digital cable system. It normally does not refer to satellite TV, which has always required a set-top box either to operate the big satellite dish, or to be the integrated receiver/decoder (IRD) in the case of direct-broadcast satellites (DBS).
The Digital Television Transition and Public Safety Act of 2005 is a United States Congress legislation enacted on October 20, 2005. This act deals with the cessation of the broadcasting of analog television and the subsequent implementation of digital television. This transition took place on June 12, 2009, which had been scheduled for February 17, 2009.
Digital television in the United States is available via digital terrestrial television (DTT), digital cable, satellite television, and IPTV providers.
CEA-909 is the ANSI standard for 8VSB/ATSC smart antennas. The basic concept is that the smart antenna either physically rotates toward the signal, or is stationary, but has elements pointed in different directions and uses only those elements that maximize the received signal. This is accomplished by feedback from the control device, such as a digital-to-analog converter box, telling the smart antenna when the signal is stronger or weaker.
Analog passthrough is a feature found on some digital-to-analog television converter boxes. Boxes without the analog passthrough feature only allow older, analog-only TVs to view digital TV. Those with analog passthrough allow both digital and analog television to be viewed on older TVs.
The digital transition in the United States was the switchover from analog to exclusively digital broadcasting of terrestrial television programming. According to David Rehr, then president and CEO of the National Association of Broadcasters, this transition represented "the most significant advancement of television technology since color TV was introduced." For full-power TV stations, the transition went into effect on June 12, 2009, with stations ending regular programming on their analog signals no later than 11:59 p.m. local time that day.
The Community Broadcasters Association (CBA) was a trade organization representing low-power broadcasting interests, including LPTV and Class A television stations, in the United States of America. It ceased operations in 2009.
The Short-term Analog Flash and Emergency Readiness Act, or SAFER Act, is a U.S. law that required the Federal Communications Commission (FCC) to allow the continuation of full-power analog TV transmissions in 2009 for an additional 30 days for the purpose of broadcasting public service announcements regarding the DTV transition in the United States and emergency information. It is also commonly known as the "DTV nightlight bill" or "analog nightlight", referring to a small nightlight that is left on after all of the other lights are out. Despite the analog shutoff deadline being extended to June 12, 2009 as part of the DTV Delay Act, stations that signed off before the deadline were still permitted to participate in the SAFER Act.
This is a review of low-power television stations (LPTV) in the United States, transmitting on VHF channel 6, which also operate as radio stations capable of being picked up by many standard FM receivers. These stations are colloquially known as "Franken FMs", a reference to Frankenstein's monster, because TV stations functioning as radio stations had not been envisioned by the Federal Communications Commission (FCC). The FCC commonly refers to these stations as "FM6" operations. All of these FM transmissions are authorized for operation on a center frequency of 87.75 MHz.
The 2016 United States wireless spectrum auction, officially known as Auction 1001, allocated approximately 100 MHz of the United States Ultra High Frequency (UHF) spectrum formerly allocated to UHF television in the 600 MHz band. The spectrum auction and subsequent reallocations were authorized by Title VI of the payroll tax cut extension passed by the United States Congress on February 17, 2012.
The digital television transition in Japan (アナログ放送終了) was the mandatory switchover from analog to digital terrestrial television broadcasting that began in 2008 and continued through early 2012. The switchover itself took place between 24 July 2011 and 31 March 2012, and involved television stations across all five major commercial networks, the entire network of NHK's broadcast transmitters, and television stations that are part of the JAITS group. Japan was the first country in eastern Asia to cease broadcasting television signals in analog.
References
General
Title III of the Deficit Reduction Act of 2005, Pub. No. 109-171 (Feb. 8, 2006).
Request for Comment and Notice of Proposed Rules to Implement and Administer a Coupon Program for Digital-to-Analog Converter Boxes, Docket Number 060512129-6129-01 (Jul. 25, 2006).
↑ Consumer and Government Affairs Bureau (May 10, 2011). "Antennas and Digital Television". FCC.gov. Federal Communications Commission. Retrieved June 26, 2011.
↑ Moskovciak, Matthew (September 30, 2008). "Winegard RCDT09A". CNET Reviews. CBS Interactive. Retrieved June 26, 2011.
↑ Guy, Colin (February 16, 2009). "Southeast Texans might have more time to prep for digital switch". Beaumont Enterprise. Beaumont, TX: Hearst Newspapers. Retrieved June 26, 2011. Although Burlington, Iowa-based Winegard produces a battery-powered digital converter box, some viewers might find that the tiny antennas attached to portable televisions and the rabbit-ears in their living room aren't sufficient to pick up a digital signal.
↑ DTVAnswers.com (June 4, 2008). Digital Television (DTV) Transition Campaign Overview(PPT) (Report). National Association of Broadcasters. Retrieved June 26, 2011. NAB's DTVanswers.com estimates 1,295 stations relocating to a channel different than their NTSC channel, many across bands.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
