Distributed transmission system

Last updated

In North American digital terrestrial television broadcasting, a distributed transmission system (DTS or DTx) is a form of single-frequency network in which a single broadcast signal is fed via microwave, landline, or communications satellite to multiple synchronised terrestrial radio transmitter sites. The signal is then simultaneously broadcast on the same frequency in different overlapping portions of the same coverage area, effectively combining many small transmitters to generate a broadcast area rivalling that of one large transmitter or to fill gaps in coverage due to terrain or localized obstacles.

Contents

History

While the idea of a single-frequency network of multiple transmitters broadcasting the same programming on the same channel from multiple transmitter sites is not a new concept, the ATSC digital television standard in use in North America was not designed for this mode of operation and was poorly adapted to these applications. The restrictive timing requirements and poor multipath interference handling of early ATSC implementations would have precluded multiple synchronous transmitters on the same frequency at the time of the first wide-scale commercial ATSC deployment in 1998; these restrictions eased somewhat as receiver design advanced in subsequent years. By 2004, technology existed to provide digital television receivers with the means to detect static (not mobile or changing) multipath interference (subject to certain timing constraints) and compensate for its effects on the digital signal.

Tests have been run by various individual broadcasters or broadcast groups, including the Metropolitan Television Alliance (MTVA, a consortium of New York city television stations). [1] A series of initial tests involving four distributed transmission sites and over 100 test measurement sites in NYC and New Jersey were completed in June 2008, along with smaller-scale tests in New York in 2007. The New York market is uniquely problematic for multipath reception due to the large number of man-made obstacles which prevent adequate digital coverage of the entire city from the main broadcast facilities atop the Empire State Building.

Technical issues

To the receiver, a signal from a single-frequency network appears as a single broadcast with strong multipath interference; in the worst case, it is detected as a main signal and a reflection both of equal strength as signals arrive from multiple transmitters to the same intermediate location at slightly different times.

The ATSC standard used for digital television in North America, unlike the DVB-T standard in Europe and other nations, uses 8VSB instead of OFDM—a modulation which allowed a station to transmit at lower peak power levels, but which historically has been far inferior in handling multipath reflections and RF interference.

The first widespread commercial deployment of US ATSC digital television began in 1998, with the first early adopters being stations in the largest markets (including New York city, served by transmitters atop the World Trade Center). Digital receivers of this era, while expensive, were poorly equipped to deal with reflected signals—a severe drawback in urbanised environments. Later generations of receiver design significantly mitigated these limitations; by 2004 technology existed to build receivers capable of detecting and compensating for static multipath interference conditions where a single echo was 10 dB weaker (within a 30 microsecond time difference) or the same strength (the worst case, but within a 12 microsecond range). [2]

If the transmitters could be kept at sufficiently precise synchronisation and sufficiently close geographical spacing to operate within these limits, a single-frequency network using the new receiver design would be possible even with the existing North American ATSC digital broadcast standards. [3]

Tests by Pennsylvania State University public educational WPSX-TV (now WPSU-TV) were initially made in 2003 [4] WPSU was in analog a VHF 3 station which serves State College, Pennsylvania from a distant transmitter which must also cover Johnstown and Altoona. As a digital station, WPSU had used a large UHF 15 transmitter at the location of the original low-VHF broadcast tower, leading to localised problems with terrain shielding which interfered with UHF reception in State College itself. Relocation of the main transmitter would have interfered with the station's ability to serve the other two communities. Addition of a small (50 kW) synchronised digital TV transmitter in State College, on the same frequency as the main UHF 15 signal, proved a means to improve reception; further improvements would be possible by adding small co-channel 50 kW transmitters in each community to be served.

ATSC released standards on September 25, 2004, as guidance on the design of multiple transmitters, single frequency networks and multiple frequency networks. [5] The new 2004 standards included:

Technical issues addressed included that of synchronization between transmitters (GPS was used to supply a 1 Hz and a 10 MHz reference frequency, as well as timing information) and precise control of transmitted frequencies (to within 1 Hz). Identification for each individual transmitter needed to be embedded in the signal for troubleshooting purposes, yet the main data stream on every synchronised transmitter must be identical; this is done by adding a second, low bit rate spread spectrum signal 27–30 dB weaker than the main signal. As this "watermark" identifier is buried under the stronger main signal, multiple repetitions of this same identifier could be received and summed in order to provide a readable version of the watermark to broadcast technicians. A standard receiver, meanwhile, would see the same signal from all transmitters by design.

The generation of non-MPEG data carried as part of the transport layer (such as the position of transmitted frame sync, or the initial state of trellis encoding devices) would also have to be matched exactly between every synchronized transmitter. Even though this data is discarded after the received signal is demodulated, any mismatch could create interference between the various co-channel signals. An extra “operations and maintenance” distributed transmission packet (OMP, packet identifier PID:0x1FFA) would need to be added to the ATSC data at the studio and used to control various parameters needed for configuration and synchronization of the individual transmitters.

The location, directional pattern and power levels for each of the transmitters would also have to be very carefully chosen, as the ATSC system is subject to very strict limits on the maximum time difference between arrival of multiple versions of the same signal at the receiver. In problem reception areas, significant improvements could be obtained but careful design would be required to operate multiple co-channel transmitters without destructive interference. [7]

Further tests run by Telemundo owned-and-operated station WNJU, Ion TV and broadcast tower owner Richland Towers using one main New Jersey transmitter and a Times Square fill-in DTS secondary transmitter [8] in 2007 indicated that, of fifteen test sites for reception of the station in New York city, 40% would obtain a substantial improvement in signal by the addition of a second transmitter to the existing station, [9] while all but one would receive at least the same signal quality as was observed without a distributed transmission system. [10] New York's Metropolitan Television Alliance was to run similar tests, but on a larger scale, in 2007 and 2008. [11]

Regulatory issues

While the US Federal Communications Commission has supported DTS in principle since 2004, an FCC call for public comment at the end of 2005 garnered a wide spectrum of responses in early 2006, ranging from strong support by groups such as the National Association of Broadcasters [12] to widespread opposition by groups who advocate the free use of "white spaces" (unused broadcast frequencies) [13] for non-broadcast purposes [14] such as wireless data. [15]

The FCC granted six-month special technical authority to WTVE Reading, Pennsylvania in December 2006, allowing it to operate a distributed transmission system on an experimental basis but did not authorise the systems on any permanent, licensed basis at that time. [16]

An FCC-sponsored test market exercise in Wilmington, North Carolina shut down all analogue full-power commercial broadcasts at noon on September 8, 2008. While a large number of the resulting calls from viewers were straightforward questions about installation of antennas and converters, or the need to scan for channels before being able to watch digital television, hundreds more were about a more intractable problem. Viewers of longtime full-power low-VHF broadcasters like WECT (NBC 6 Wilmington), a signal which in its analogue form reached to the edge of Myrtle Beach, could no longer receive the station - even with the converter and proper antenna installation. The move to UHF 44 and a different transmitter site had substantially reduced WECT's coverage area [17] and, for many who for many years were on the fringes of the analogue NBC 6 signal, WECT was no more. [18]

On November 7, 2008, the FCC issued an order approving the use of distributed transmission systems by terrestrial DTV broadcasters, subject to various restrictions. [19] This allows broadcasters to apply for DTS facilities to cover the area once covered by analogue TV, while not expanding coverage beyond the existing analogue coverage area. It also prohibits a broadcaster "cherry picking" a coverage area in such a way as to cover urban areas while leaving rural viewers with no signal.

This waiver has come too late to allow the newly proposed DTS facilities to be constructed and operational before the federally mandated 2009 analogue shutoff. [20]

The Consumer Electronics Association and CTIA proposed in December 2009 to force all stations to use this method, so that the companies they represent could use the remaining space in the TV band for mobile broadband. Unlike the digital television transition in the United States, they do not propose that stations be forced to pay for it however, much like the 2 GHz broadcast auxiliary service was forced to move by the FCC, but only after the beneficiary (Sprint Nextel) compensated broadcasters for the regulatory taking. [21]

Individual broadcasters

In Puerto Rico, Spanish language independent WSTE 7 "Super Siete" currently operates multiple analogue transmitters on the same frequency to cover various portions of the same island; this system has shown limitations due to interference between the transmitters if all are operational simultaneously. Use of a properly synchronised digital DTS could help to reduce this interference.

In Pennsylvania, independent WTVE is licensed to serve Reading even though its primary audience is in Philadelphia. A distributed transmission system now allows it to tailor its coverage area to improve coverage in areas where its signal is currently marginal.

In Virginia public television WVPT/WVPY operate a combined total of five additional on-channel synchronised transmitters to fill areas blocked by mountains from two main VHF/UHF transmitters; a set of US$100,000 synchronised digital transmitters can replace service from the same number of conventional analogue broadcast translators and also enable overnight datacasting of instructional materials to the area's 188 schools. [22] [23]

In New Mexico, Telemundo affiliate KTDO proposes DTS as a means of pairing a low-power DTV facility currently operating in its community of license (Las Cruces) with a second facility atop a mountain overlooking El Paso, Texas in order to reach a wider audience. [24]

In Missouri, FOX affiliate KRBK operates a DTS as a way to service the Springfield, Missouri market from 5 transmission points based around the Springfield DMA. This system went on air in late 2011, and is still being revised today.

In Alaska, Anchorage CBS affiliate KAUU operates with limited resources and equipment, covering a large and sparsely populated area with many small broadcast translator stations. While broadcast signal synchronization is not an issue (as the overlap between signals falls entirely into unpopulated areas), the ability to re-use multiple small transmitters may allow the station to avoid the cost of building one large, expensive main transmitter for its digital signal.

See also

Related Research Articles

8VSB is the modulation method used for broadcast in the ATSC digital television standard. ATSC and 8VSB modulation is used primarily in North America; in contrast, the DVB-T standard uses COFDM.

A broadcast range is the service area that a broadcast station or other transmission covers via radio waves. It is generally the area in which a station's signal strength is sufficient for most receivers to decode it. However, this also depends on interference from other stations.

<span class="mw-page-title-main">ATSC standards</span> Standards for digital television in the US

Advanced Television Systems Committee (ATSC) standards are an international set of standards for broadcast and digital television transmission over terrestrial, cable and satellite networks. It is largely a replacement for the analog NTSC standard and, like that standard, is used mostly in the United States, Mexico, Canada, South Korea and Trinidad & Tobago. Several former NTSC users, such as Japan, have not used ATSC during their digital television transition, because they adopted other systems such as ISDB developed by Japan, and DVB developed in Europe, for example.

Multichannel Television Sound (MTS) is the method of encoding three additional audio channels into analog 4.5 MHz audio carriers on System M and System N. It was developed by the Broadcast Television Systems Committee, an industry group, and sometimes known as BTSC as a result.

Broadcasttelevision systems are the encoding or formatting systems for the transmission and reception of terrestrial television signals.

The following tables show the frequencies assigned to analog broadcast television channels in various regions of the world, along with the ITU letter designator for the system used. The frequencies shown are for the analog video and audio carriers. The channel itself occupies several megahertz of bandwidth. For example, North American channel 1 occupies the spectrum from 44 to 50 MHz. See Broadcast television systems for a table of signal characteristics, including bandwidth, by ITU letter designator. Analog television broadcasts have been phased out in most regions, having been replaced by digital television broadcasts.

<span class="mw-page-title-main">Single-frequency network</span>

A single-frequency network or SFN is a broadcast network where several transmitters simultaneously send the same signal over the same frequency channel.

<span class="mw-page-title-main">WPSU-TV</span> PBS member station in Clearfield, Pennsylvania

WPSU-TV is a PBS member television station licensed to Clearfield, Pennsylvania, United States, serving West-Central Pennsylvania. Owned by the Pennsylvania State University as part of Penn State Public Media, it is sister to NPR member WPSU and student radio station WKPS. The three stations share studios at Innovation Park on Penn State's University Park campus in State College. WPSU-TV's primary transmitter is located seven miles (11 km) north of Clearfield in Lawrence Township, with a secondary transmitter in Pine Grove Mills, Pennsylvania.

<span class="mw-page-title-main">MediaFLO</span> Media transmission technology developed by Qualcomm

MediaFLO was a technology developed by Qualcomm for transmitting audio, video and data to portable devices such as mobile phones and personal televisions, used for mobile television. In the United States, the service powered by this technology was branded as FLO TV.

<span class="mw-page-title-main">ATSC tuner</span> Tuner for digital television channels

An ATSCtuner, often called an ATSC receiver or HDTV tuner, is a type of television tuner that allows reception of digital television (DTV) television channels that use ATSC standards, as transmitted by television stations in North America, parts of Central America, and South Korea. Such tuners are usually integrated into a television set, VCR, digital video recorder (DVR), or set-top box which provides audio/video output connectors of various types.

Mobile television is television watched on a small handheld or mobile device, typically developed for that purpose. It includes service delivered via mobile phone networks, received free-to-air via terrestrial television stations, or via satellite broadcast. Regular broadcast standards or special mobile TV transmission formats can be used. Additional features include downloading TV programs and podcasts from the Internet and storing programming for later viewing.

A digital channel election was the process by which television stations in the United States chose which physical radio-frequency TV channel they would permanently use after the analog shutdown in 2009. The process was managed and mandated by the Federal Communications Commission for all full-power TV stations. Low-powered television (LPTV) stations are going through a somewhat different process, and are also allowed to flash-cut to digital.

A-VSB or Advanced VSB is a modification of the 8VSB modulation system used for transmission of digital television using the ATSC system. One of the constraints of conventional ATSC transmission is that reliable reception is difficult or impossible when the receiver is moving at speeds associated with normal vehicular traffic. The technology was jointly developed by Samsung and Rohde & Schwarz.

Digital terrestrial television in Canada is transmitted using the ATSC standard. Because Canada and the U.S. use the same standard and frequencies for channels, people near the Canada–United States border can watch digital television programming from television stations in either country where available. The ATSC standards are also used in Mexico, the Dominican Republic, Suriname, and South Korea.

ATSC-M/H is a U.S. standard for mobile digital TV that allows TV broadcasts to be received by mobile devices.

<span class="mw-page-title-main">Broadcast relay station</span> Repeater transmitter

A broadcast relay station, also known as a satellite station, relay transmitter, broadcast translator (U.S.), re-broadcaster (Canada), repeater or complementary station (Mexico), is a broadcast transmitter which repeats the signal of a radio or television station to an area not covered by the originating station.

<span class="mw-page-title-main">Digital television transition in the United States</span> 2009 switchover in the U.S. from analog to digital broadcasting of TV programming

The digital television transition in the United States was the switchover from analog to exclusively digital broadcasting of terrestrial television programming. Under the Digital Transition and Public Safety Act of 2005, full-power broadcasting of analog television in the United States was initially planned to have ceased after February 17, 2009, but this was delayed to June 12, 2009, after the passage of the DTV Delay Act on February 4, 2009. This date was a further delay from the original date of December 31, 2006, as stipulated in the Telecommunications Act of 1996. The delay to June 12 was to assist households on a waiting list for coupons for digital converter boxes, funding for which was provided by the American Recovery and Reinvestment Act of 2009.

This is a review of low-power television stations (LPTV) in the United States, transmitting on VHF channel 6, which also operate as radio stations capable of being picked up by many standard FM receivers. These stations are colloquially known as "Franken FMs", a reference to Frankenstein's monster, because TV stations functioning as radio stations had not been envisioned by the Federal Communications Commission (FCC). The FCC commonly refers to these stations as "FM6" operations. All of these FM transmissions are authorized for operation on a center frequency of 87.75 MHz.

<span class="mw-page-title-main">UHF television broadcasting</span> Ultra high frequency radio to transmit TV

UHF television broadcasting is the use of ultra high frequency (UHF) radio for over-the-air transmission of television signals. UHF frequencies are used for both analog and digital television broadcasts. UHF channels are typically given higher channel numbers, like the US arrangement with VHF channels (initially) 1 to 13, and UHF channels (initially) numbered 14 to 83. Compared with an equivalent VHF television transmitter, to cover the same geographic area with a UHF transmitter requires a higher effective radiated power, implying a more powerful transmitter or a more complex antenna. However, the additional channels allow more broadcasters in a given region without causing objectionable mutual interference.

References

  1. ↑ NTIA: NYC 9/11 Digital Television Transition Project
  2. ↑ Wu, Y.; Xianbin Wang; Citta, R.; Ledoux, B.; Lafleche, S.; Caron, B. (2004). "An ATSC DTV receiver with improved robustness to multipath and distributed transmission environments". IEEE Transactions on Broadcasting. 50: 32–41. doi:10.1109/TBC.2004.823843. S2CID   8529935.
  3. ↑ Design procedures and field test results of a distributed-translator network, and a case study for an application of distributed-transmission; SALEHIAN K., WU Y., CARON B.; Communications Research Centre (CRC) Ottawa, IEEE transactions on broadcasting, 2006, ISSN 0018-9316 IETBAC.
  4. ↑ WPSX-TV set to begin experimental DTX transmission, May 15, 2003 12:00 PM
  5. ↑ ATSC approves new recommended practice A/111: Design of Synchronized Multiple Transmitter Networks, September 25, 2004 Archived December 15, 2008, at the Wayback Machine
  6. ↑ ATSC distributed transmission, Broadcast Engineering, February 2, 2007
  7. ↑ The ATSC Distributed Transmission System and Applications to Translator Service Archived March 26, 2009, at the Wayback Machine , David L. Hershberger, Axcera LLC
  8. ↑ SFN: Are Many Transmitters Better Than One?, Merrill Weiss, TV Newsday, Sep 13 2007
  9. ↑ Richland Towers/Telemundo/ION report on DTS
  10. ↑ SFN TV Broadcasting in The United States?, Randy Hoffner, TV Technology, October 3, 2007
  11. ↑ MTVA Gets Approval for NYC Distributed Transmission System, TV Technology, May 25, 2007
  12. ↑ National Association of Broadcasters submission to FCC, 2006, supporting DTS
  13. ↑ Opposition to DTV DTS, various organisations, as filed with FCC in 2006
  14. ↑ CommonCause.org objections to DTS, FCC 2006 filing Archived November 28, 2008, at the Wayback Machine
  15. ↑ New America: Opposition to DTV DTS, 2006
  16. ↑ Transmission boost: The FCC permits a distributed transmission system, Harry C. Martin, Broadcast Engineering, Feb 1, 2007 Archived December 15, 2008, at the Wayback Machine
  17. ↑ Confronting the Cliff Effect Archived 2009-02-27 at the Wayback Machine , Paige Albiniak, TV Broadcast, December 26, 2008
  18. ↑ FCC OKs digital workaround for DTV signal range problems, Matthew Lasar, ArsTechnica, November 11, 2008
  19. ↑ "FCC order on distributed transmission, November 2008" (PDF). Archived from the original (PDF) on 2011-10-17. Retrieved 2008-12-10.
  20. ↑ "Home Theater News: FCC Green-Lights DTV Range Fix, Mark Fleischmann, November 17, 2008". Archived from the original on July 11, 2012. Retrieved December 10, 2008.
  21. ↑ "CEA, CTIA pitch low-power broadcast model to free up spectrum for broadband use". Archived from the original on 2010-01-13. Retrieved 2009-12-29.
  22. ↑ WVPY application for experimental DTS transmitter at Luray VA
  23. ↑ "Archived copy" (PDF). Archived from the original (PDF) on 2009-03-05. Retrieved 2009-03-10.{{cite web}}: CS1 maint: archived copy as title (link)
  24. ↑ "Application View ... Redirecting".
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.