Destiny (ISS module)

Last updated
Destiny
ISS Destiny Lab.jpg
The Destiny Laboratory Module (NASA) being installed on the International Space Station.
Module statistics
Launch date 7 February 2001
Launch vehicle Space Shuttle Atlantis
Docked 10 February 2001
Mass 14,515 kilograms (32,000 lb)
Length8.4 metres (28 ft)
Diameter4.2 metres (14 ft)
Pressurised volume 104.77 m3 (3,700 cu ft)
References: [1]

The Destiny module, also known as the U.S. Lab, is the primary operating facility for U.S. research payloads aboard the International Space Station (ISS). [2] [3] It was berthed to the Unity module and activated over a period of five days in February, 2001. [4] Destiny is NASA's first permanent operating orbital research station since Skylab was vacated in February 1974.

Contents

The Boeing Company began construction of the 14.5-tonne (32,000 lb) research laboratory in 1995 at the Michoud Assembly Facility and then the Marshall Space Flight Center in Huntsville, Alabama. [2] Destiny was shipped to the Kennedy Space Center in Florida in 1998, and was turned over to NASA for pre-launch preparations in August 2000. It launched on February 7, 2001 aboard the Space Shuttle Atlantis on STS-98. [4]

Astronauts work inside the pressurized facility to conduct research in numerous scientific fields. Scientists throughout the world would use the results to enhance their studies in medicine, engineering, biotechnology, physics, materials science, and Earth science. [3]

Launch and installation

Mission patch for STS-98 Sts-98-patch.svg
Mission patch for STS-98

Destiny was launched to ISS aboard the Space Shuttle mission STS-98. [4] It launched into Earth orbit on February 7, 2001 aboard the Space Shuttle Atlantis. [4] On February 10, 2001 at 9:50 am CST, the installation of Destiny began. [5] First, the Shuttle SRMSS (CanadaArm) was used to remove Pressurized Mating Adapter 2 (PMA 2) from Unity node's forward port to make room for the new module. PMA-2 was temporarily stowed on the forward berthing ring of the Z1 truss. Destiny was "grabbed" by the robotic arm at 11:23, lifted out of Atlantis' cargo bay, and berthed to the forward port of Unity. Two days later, PMA-2 was moved to its semi-permanent location on the forward hatch of Destiny. [6] (See also Pressurized Mating Adapter and Z1 Truss.) Several years later, on November 14, 2007, the Harmony module was attached to the forward end of the Destiny laboratory. [7]

The addition of Destiny increased the habitable volume by 3,800 cubic feet, an increase of 41 percent. [5]

Laboratory structure

The Destiny laboratory as it looked following installation in 2001. Destiny as just installed.jpg
The Destiny laboratory as it looked following installation in 2001.
Interior view of the US lab with the lights turned off, i.e. while the crew sleeps ISS-40 Space Station while the crew is asleep.jpg
Interior view of the US lab with the lights turned off, i.e. while the crew sleeps

The U.S. laboratory module is 28 feet (8.5 m) long and 14 feet (4.3 m) wide. [2] [3] It is made from aluminum and stainless steel, and comprises three cylindrical sections and two endcones that contain the hatch openings through which astronauts enter and exit the module. [2] The aft port of Destiny is connected to the forward port of Unity, and the forward port of Destiny is connected to the aft port of Harmony . The ends are colored blue and white respectively for the crew to navigate easily. [7] [8] A 20-inch (510 mm)-diameter window is located on one side of the center module segment. [3]

Each of the two berthing ports on Destiny contains a hatch. [3] Both hatches are normally open, and remain open unless a situation arises requiring a module to be isolated. Each hatch has a window. The hatches can be opened or closed from either side. The hatches have a pressure interlock feature, which prevents the hatch from being opened if there is a negative pressure across the hatch (higher pressure on the outside of the hatch). The hatch openings are a square-like six sided shape - which is associated to that module.

Destiny has a 20-inch (510 mm) optically pure, telescope-quality glass window located in an open rack bay used primarily for Earth science observations. [2] [3] [9] Station crewmembers use very high quality video and still cameras at the window to record Earth's changing landscapes. A window shutter protects the window from potential micrometeoroid and orbital debris strikes during the life of the ISS. The crew manually opens the shutter to use the window.

Imagery captured from Destiny's window has given geologists and meteorologists the chance to study floods, avalanches, fires and ocean events such as plankton blooms in a way never seen before, as well as given international scientists the opportunity to study features such as glaciers, coral reefs, urban growth and wild fires. [3]

Specifications

Joan E. Higginbotham and Sunita L. Williams work the controls of the Space Station Remote Manipulator System in the Destiny laboratory. Astronauts Joan Higginbotham (STS-116) and Sunita Williams (Expedition 14) on the International Space Station.jpg
Joan E. Higginbotham and Sunita L. Williams work the controls of the Space Station Remote Manipulator System in the Destiny laboratory.

Equipment

Leland D. Melvin and STS-122 mission specialists working on robotic equipment in the US lab S122e007776 orig.jpg
Leland D. Melvin and STS-122 mission specialists working on robotic equipment in the US lab

As with the European and Japanese laboratories of the station, payloads inside Destiny are configured around International Standard Payload Racks (ISPRs), that can be removed or reconfigured for various experiments and equipment. [9] Made out of a graphite composite shell, each rack weighs about 1,200 pounds (540 kg), and is about 73 inches (1,900 mm) high, and 42 inches (1,100 mm) wide. [9] The eight rack bays are equipped with curtains that provide around 290 cubic feet (8.2 m3) of temporary stowage space when not occupied by experiments. [9]

Destiny arrived at the station pre-configured with five racks housing electrical and life support systems that provide electrical power, cooling water, air revitalization, and temperature and humidity control. Seven additional racks were flown to Destiny in the Leonardo Multi-Purpose Logistics Module by STS-102, and ten more were delivered on subsequent missions. Destiny can hold up to 13 payload racks with experiments in human life science, materials research, Earth observations and commercial applications. [3] The laboratory has a total of 24 racks inside the laboratory, six on each side. [2]

Internal to the laboratory are racks, rack stand-offs, and vestibule jumpers. [10] The lab racks house the system hardware in removable modular units. The stand-offs provide space for electrical connections, data management systems cabling for computers, air conditioning ducts, thermal control tubes and more, all of which support the space station's equipment racks. [10] The racks interface to the piping and wiring in the standoff via outlets and ports located in the standoffs at the base end of each rack location.

Jumpers in the vestibule, the area between Unity and Destiny, connect the piping and wiring between the two. Grounding straps between Unity and Destiny will be installed. One side of the grounding strap will be connected to the Active Common Berthing Mechanism (ACBM) on Unity, while the other end will be connected to the Passive Common Berthing Mechanism (PCBM) on Destiny.

Some of the mechanisms on Destiny are the CBMs (passive and active), hatches, and the laboratory window shutter. The ACBM is in the forward port of the laboratory. It is attached to the Harmony node. [8] The PCBM on Destiny is located in the laboratory's aft port. The ACBM in Unity's forward port is latched to the laboratory's PCBM to berth Destiny to Unity.

Science equipment

Alexander Gerst works in the Destiny module ISS-56 Alexander Gerst works in the Destiny module (1).jpg
Alexander Gerst works in the Destiny module

Destiny also contains the Minus Eighty Degree Laboratory Freezer for ISS (MELFI), transported to the Space Station on STS-121. [11] The freezer is used both to store samples and reagents on the station, and to transport them to and from the space station in a temperature controlled environment. [12]

Currently installed at the main observation window of Destiny is the Agricultural Camera (AgCam). It is a multi-spectral imaging system built and primarily operated by students and faculty at the University of North Dakota. Its purpose is to take frequent images, in visible and infrared light, of vegetated areas on the Earth and promises to deliver a greater effectiveness for in-season agriculture applications research and operational decision support than current satellite systems such as Landsat. [13]

Veggie

In 2016 the ISS crew operated Veg-03 experiment. [14] In November they harvested a crop of edible romaine lettuce which contributed to the crew's meal. [15] Also samples of cabbage are returned to Earth for testing as part of the experiment. [14] This uses the Veggie experiment module in Destiny, which can provide light and nutrients for plant growth experiments. [15]

Destiny nadir window

The nadir window is formally known as the U.S. Laboratory Science Window, has the "...highest quality optics ever flown on a human occupied spacecraft...", according to NASA, and can support taking Earth observations/images. [16] In 2010 a research facility was brought to the station, called WORF, and the first photo with it was taken in January 2011. [17] WORF was delivered by ISS Flight 19A (which was STS-131) . [17]

WORF

Naoko Yamazaki installing Window Observational Research Facility STS-131 Naoko Yamazaki installs WORF.jpg
Naoko Yamazaki installing Window Observational Research Facility

In 2010 the WORF was brought to ISS aboard STS-131 and installed. [16] This is a facility that uses the Destiny nadir window to support various types of photography and observation. [16] WORF, which stands for Window Observational Research Facility is constructed based on International Standard Payload Rack (ISPR) and EXPRESS Rack program technology. [16] The first photo taken by WORF was on January 21, 2011 with Ag Cam. [16]

The name WORF is an allusion to Worf, the fictional character of the same name who appeared in the science fiction television and film franchise Star Trek . A special mission patch for WORF was issued that featured text written in the Klingon language. [18] Another cross-over of the Star Trek franchise and space exploration was the naming of Space Shuttle Enterprise.

A similar window is Nauka module's porthole window.

In media

See also

After its installation, habitation and use of Destiny is similar to ISS history as an integrated part of that Space station:

Related Research Articles

<i>Columbus</i> (ISS module) ESA science observatory on the International Space Station

Columbus is a science laboratory that is part of the International Space Station (ISS) and is the largest single contribution to the ISS made by the European Space Agency (ESA).

<i>Kibō</i> (ISS module) Japanese ISS module, used on ISS press conferences

The Japanese Experiment Module (JEM), nicknamed Kibō, is a Japanese science module for the International Space Station (ISS) developed by JAXA. It is the largest single ISS module, and is attached to the Harmony module. The first two pieces of the module were launched on Space Shuttle missions STS-123 and STS-124. The third and final components were launched on STS-127.

<span class="mw-page-title-main">STS-88</span> First Space Shuttle mission to the International Space Station

STS-88 was the first Space Shuttle mission to the International Space Station (ISS). It was flown by Space Shuttle Endeavour, and took the first American module, the Unity node, to the station.

<span class="mw-page-title-main">STS-98</span> 2001 American crewed spaceflight to the ISS

STS-98 was a 2001 Space Shuttle mission to the International Space Station (ISS) flown by Space Shuttle Atlantis. It was the first human spaceflight launch of the 21st century. STS-98 delivered to the station the Destiny Laboratory Module. All mission objectives were completed and the shuttle reentered and landed safely at Edwards Air Force Base on 20 February 2001, after twelve days in space, six of which were spent docked to the ISS.

<span class="mw-page-title-main">Mario Runco Jr.</span> American astronaut (born 1952)

Mario Runco Jr. is a former United States Naval officer and NASA astronaut. He was selected as an astronaut with in 1987. He flew three Space Shuttle missions, performed a spacewalk on his second mission, and is now retired both from NASA and the U.S. Navy.

<span class="mw-page-title-main">Multi-Purpose Logistics Module</span> Large pressurized container for cargo resupply of the International Space Station

A Multi-Purpose Logistics Module (MPLM) is a large pressurized container that was used on Space Shuttle missions to transfer cargo to and from the International Space Station (ISS). Two MPLMs made a dozen trips in the Shuttle cargo bay and initially berthed to the Unity module and later the Harmony module on the ISS. From there, supplies were offloaded, and finished experiments and waste were reloaded. The MPLM was then reberthed in the Shuttle for return to Earth. Three modules were built by the Italian Space Agency (ASI): Leonardo, Raffaello, and Donatello.

<i>Unity</i> (ISS module) American module of the International Space Station

The Unity connecting module, also known as Node 1, is the first U.S.-built component of the International Space Station (ISS). It connects the Russian and United States segments of the station, and is where crew eat meals together.

<span class="mw-page-title-main">Expedition 2</span> 2nd expedition to the International Space Station

Expedition 2 was the second long-duration spaceflight aboard the International Space Station, immediately following Expedition 1. Its three-person crew stayed aboard the station from March to August 2001. In addition to station maintenance, the crew assisted in several station assembly missions, welcomed the first space tourist Dennis Tito, and conducted some scientific experiments.

<i>Harmony</i> (ISS module) American module of the International Space Station

Harmony, also known as Node 2, is the "utility hub" of the International Space Station. It connects the laboratory modules of the United States, Europe and Japan, as well as providing electrical power and electronic data. Sleeping cabins for four of the crew are housed here.

<i>Tranquility</i> (ISS module) American module of the International Space Station

Tranquility, also known as Node 3, is a module of the International Space Station (ISS). It contains environmental control systems, life support systems, a toilet, exercise equipment, and an observation cupola.

<span class="mw-page-title-main">Minus Eighty Degree Laboratory Freezer for ISS</span> Experiment storage freezer for the ISS

The Minus Eighty-Degree Laboratory Freezer for ISS (MELFI) is a European-built experiment storage freezer for the International Space Station. It comprises four independent dewars which can be set to operate at different temperatures. Currently temperatures of −80 °C, −26 °C, and +4 °C are used during on-orbit ISS operations. Both reagents and samples will be stored in the freezer. As well as storage the freezer is designed to be used to transport samples to and from the ISS in a temperature controlled environment. The total capacity of the unit is 300 litres.

<span class="mw-page-title-main">STS-128</span> 2009 American crewed spaceflight to the ISS

STS-128 was a NASA Space Shuttle mission to the International Space Station (ISS) that launched on August 28, 2009. Space ShuttleDiscovery carried the Multi-Purpose Logistics Module Leonardo as its primary payload. Leonardo contained a collection of experiments for studying the physics and chemistry of microgravity. Three spacewalks were carried out during the mission, which removed and replaced a materials processing experiment outside ESA's Columbus module, and returned an empty ammonia tank assembly.

<span class="mw-page-title-main">STS-130</span> 2010 American crewed spaceflight to the ISS

STS-130 was a NASA Space Shuttle mission to the International Space Station (ISS). Space ShuttleEndeavour's primary payloads were the Tranquility module and the Cupola, a robotic control station with six windows around its sides and another in the center, providing a 360-degree view around the station. Endeavour launched at 04:14 EST on February 8, 2010 and landed at 22:22 EST on February 21, 2010, on runway 15 at the Kennedy Space Center's Shuttle Landing Facility.

<span class="mw-page-title-main">STS-131</span> 2010 American crewed spaceflight to the ISS

STS-131 was a NASA Space Shuttle mission to the International Space Station (ISS). Space ShuttleDiscovery launched on April 5, 2010, at 6:21 am from LC-39A, and landed at 9:08 am on April 20, 2010, on runway 33 at the Kennedy Space Center's Shuttle Landing Facility. The mission marked the longest flight for Space Shuttle Discovery.

<span class="mw-page-title-main">Common Berthing Mechanism</span> Berthing mechanism used to connect ISS modules

The Common Berthing Mechanism (CBM) connects habitable elements in the US Orbital Segment (USOS) of the International Space Station (ISS). The CBM has two distinct sides that, once mated, form a cylindrical vestibule between modules. The vestibule is about 16 inches (0.4 m) long and 6 feet (1.8 m) across. At least one end of the vestibule is often limited in diameter by a smaller bulkhead penetration.

<span class="mw-page-title-main">Pressurized Mating Adapter</span> Spacecraft docking adapter

A Pressurized Mating Adapter (PMA) is a spacecraft adapter used on the International Space Station (ISS) to convert a Common Berthing Mechanism (CBM) interface to an APAS-95 docking port. Three PMAs are connected to the US Orbital Segment of ISS. PMA-1 and PMA-2 were launched with the Unity module in 1998 aboard STS-88; PMA-3 was launched in 2000 aboard STS-92. PMA-1 permanently connects the Unity and Zarya modules. IDA adapters have been installed on PMA-2 and PMA-3 which convert them to IDSS docking ports.

<span class="mw-page-title-main">Kounotori 2</span> 2011 Japanese resupply spaceflight to the ISS

Kounotori 2, also known as HTV-2, was launched in January 2011 and was the second flight of the Japanese H-II Transfer Vehicle to resupply the International Space Station (ISS). It was launched by the H-IIB Launch Vehicle No. 2 manufactured by Mitsubishi Heavy Industries (MHI) and JAXA. After the supplies were unloaded, Kounotori 2 was loaded with waste material from ISS, including used experiment equipment and used clothes. Kounotori 2 was then unberthed and separated from the ISS and burned up upon reentering the atmosphere on 30 March 2011.

<i>Leonardo</i> (ISS module) Italian module of the International Space Station

The Leonardo Permanent Multipurpose Module (PMM) is a module of the International Space Station. It was flown into space aboard the Space Shuttle Discovery on STS-133 on 24 February 2011 and installed on 1 March. Leonardo is primarily used for storage of spares, supplies and waste on the ISS, which was until then stored in many different places within the space station. It is also the personal hygiene area for the astronauts who live in the US Orbital Segment. The Leonardo PMM was a Multi-Purpose Logistics Module (MPLM) before 2011, then was modified into its current configuration. It was formerly one of two MPLM used for bringing cargo to and from the ISS with the Space Shuttle. The module was named for Italian polymath Leonardo da Vinci.

<span class="mw-page-title-main">US Orbital Segment</span> US components of the International Space Station

The US Orbital Segment (USOS) is the name given to the components of the International Space Station (ISS) constructed and operated by the United States National Aeronautics and Space Administration (NASA), European Space Agency (ESA), Canadian Space Agency (CSA) and Japan Aerospace Exploration Agency (JAXA). The segment consists of eleven pressurized components and various external elements, almost all of which were delivered by the Space Shuttle.

<span class="mw-page-title-main">Window Observational Research Facility</span> Experiment rack facility manufactured by the Brazilian Space Agency

The Window Observational Research Facility (WORF) is an experiment rack facility manufactured by the Brazilian Space Agency, which remotely operated payloads and crew members can perform Earth and space science research, including hand held photography, at the U.S. Laboratory Science Window on the International Space Station. WORF is based on an International Standard Payload Rack (ISPR) and utilizes avionics and hardware adapted from the EXPRESS Rack program. The rack provides a payload volume equivalent to 0.8 m3 (28 cu ft), and will be able to support up to three payloads simultaneously, depending on available resources and space available at the window. The WORF will also provide access and equipment for crew Earth observations, such as crew restraints, camera/camcorder brackets, and condensation prevention. WORF payloads include those focusing on geology, agriculture, ranching, environmental and coastal changes, and education.

References

  1. ↑ "Destiny Laboratory | NASA". 20 September 2018. Archived from the original on 9 July 2007. Retrieved 28 January 2014.
  2. 1 2 3 4 5 6 Boeing (2008). "Destiny Laboratory Module". Boeing . Retrieved October 7, 2008.
  3. 1 2 3 4 5 6 7 8 NASA (2003). "U.S. Destiny Laboratory". NASA. Archived from the original on July 9, 2007. Retrieved October 7, 2008.
  4. 1 2 3 4 NASA (2001). "STS-98". NASA. Archived from the original on August 30, 2013. Retrieved October 7, 2008.
  5. 1 2 "Destiny Laboratory Attached to International Space Station". 16 April 2015.
  6. ↑ STS-98, Mission Control Center (February 10, 2001). "Status Report # 07". NASA. Archived from the original on 2012-04-06. Retrieved 2007-01-18.{{cite web}}: CS1 maint: numeric names: authors list (link)
  7. 1 2 NASA (2007). "PMA-3 Relocation". NASA. Archived from the original on October 12, 2007. Retrieved September 28, 2007.
  8. 1 2 NASA (2007). "ISS On-Orbit Status 11/14/07". NASA. Archived from the original on March 7, 2008. Retrieved October 7, 2008.
  9. 1 2 3 4 Andrews Space & Technology (2001). "ISS Destiny (U.S. Laboratory Module)". Andrews Space & Technology. Archived from the original on September 6, 2008. Retrieved October 7, 2008.
  10. 1 2 NASA (1997). "International Space Station Imagery - Standoffs". NASA. Archived from the original on March 4, 2000. Retrieved October 7, 2008.
  11. ↑ NASA (2008). "STS-121". NASA. Archived from the original on October 9, 2008. Retrieved October 7, 2008.
  12. ↑ NASA (2008). "Minus Eighty-Degree Laboratory Freezer for ISS (MELFI)". NASA. Archived from the original on November 1, 2008. Retrieved October 7, 2008.
  13. ↑ "Agricultural Camera (AgCam) factsheet". NASA. 2009-02-27. Archived from the original on 2009-04-04. Retrieved 2009-03-21.
  14. 1 2 "Experiment Details".
  15. 1 2 "Weekly Recap (11/28/16) from the Expedition Lead Scientist". 7 December 2016. Archived from the original on 8 November 2020. Retrieved 1 January 2017.
  16. 1 2 3 4 5 "Experiment Details".
  17. 1 2 "NASA - Window Observational Research Facility". www.nasa.gov. Retrieved 2017-01-17.
  18. ↑ "Worf and the International Space Station – TrekToday".
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.