 | This article needs additional citations for verification .(October 2014) |
Overhangs are the lengths of a road vehicle which extend beyond the wheelbase at the front and rear. They are normally described as front overhang and rear overhang. Practicality, style, and performance are affected by the size and weight of overhangs.
Along with clearance, length of overhangs affects the approach and departure angles, which measure the vehicle's ability to overcome steep obstacles and rough terrain. The longer the front overhang, the smaller is the approach angle, and thus lesser the car's ability to climb or descend steep ramps without damaging the front bumpers. [1] Typically, the rear overhang is larger on rear-wheel drive cars, while the front overhang is larger on front-wheel drive cars. [2]
Overhangs in the case of rolling stock are the lengths from the bogie pivots to the ends of the car, or in the case of two axles the distances outside of the wheelbase to the ends of the car.
Journalist Paul Niedermeyer has proposed an overhang ratio (OHR) to characterize the combined size of the front and rear overhangs, normalized to vehicle length, computed as . [3] Because most vehicles are styled so the wheelbase is typically equal to four wheel+tyre diameters, [2] the minimum OHR (with no bodywork projecting beyond the front or rear wheels) is approximately 20%.
| Vehicle | Thumbnail | Wheelbase | Length | OHR (%) |
|---|---|---|---|---|
| Alpine A110 |  | 2,099 mm (82.6 in) | 3,850 mm (151.6 in) | 45.5 |
| BMW 507 |  | 2,480 mm (97.6 in) | 4,380 mm (172.4 in) | 43.4 |
| Cadillac Eldorado (1959) |  | 3,302 mm (130.0 in) | 5,715 mm (225.0 in) | 42.2 |
| Donkervoort D8 |  | 2,350 mm (92.5 in) | 3,740 mm (147.2 in) | 37.2 |
| Eagle Vision |  | 2,870 mm (113.0 in) | 5,121 mm (201.6 in) | 44 |
| Ferrari 612 Scaglietti |  | 2,950 mm (116.1 in) | 4,902 mm (193.0 in) | 39.8 |
| GM New Look bus (40') |  | 7,240 mm (285.0 in) | 12,190 mm (479.9 in) | 68.4 |
| Hummer H1 |  | 3,302 mm (130.0 in) | 4,686 mm (184.5 in) | 29.5 |
| Isuzu VehiCROSS |  | 2,332 mm (91.8 in) | 4,130 mm (162.6 in) | 43.5 |
| Jeep CJ-7 |  | 2,370 mm (93.3 in) | 3,759 mm (148.0 in) | 37 |
| Kaiser Dragon |  | 3,010 mm (118.5 in) | 5,364 mm (211.2 in) | 43.9 |
| Lotus Esprit (S3) |  | 2,440 mm (96.1 in) | 4,320 mm (170.1 in) | 43.5 |
| Mini (saloon) |  | 2,036 mm (80.2 in) | 3,054 mm (120.2 in) | 33.3 |
| Nissan Vanette (C22) |  | 2,075 mm (81.7 in) | 3,980 mm (156.7 in) | 47.9 |
| Oldsmobile Ninety-Eight (8th gen.) |  | 3,226 mm (127.0 in) | 5,700 mm (224.4 in) | 43.4 |
| Plymouth Superbird |  | 2,941 mm (115.8 in) | 5,613 mm (221.0 in) | 47.6 |
| Porsche 993 |  | 2,272 mm (89.4 in) | 4,260 mm (167.7 in) | 46.7 |
| Qvale Mangusta |  | 2,658 mm (104.6 in) | 4,194 mm (165.1 in) | 36.6 |
| Renault 5 |  | 2,419 mm (95.2 in) | 3,521 mm (138.6 in) | 31.3 |
| Saab 99 |  | 2,473 mm (97.4 in) | 4,340 mm (170.9 in) | 43 |
| Tesla Model S |  | 2,960 mm (116.5 in) | 4,980 mm (196.1 in) | 40.6 |
| UAZ-469 |  | 2,380 mm (93.7 in) | 4,025 mm (158.5 in) | 40.9 |
| Volkswagen Beetle |  | 2,400 mm (94.5 in) | 4,079 mm (160.6 in) | 41.2 |
| XPeng P7 |  | 2,998 mm (118.0 in) | 4,880 mm (192.1 in) | 38.6 |
| ZIL-41047 |  | 3,880 mm (152.8 in) | 6,339 mm (249.6 in) | 38.8 |
Large overhangs contribute to large vehicle dimensions, and the associated advantages of size. On front-engined saloon/sedans, measuring rear overhang is helpful in predicting the size of the trunk. For these same vehicles, large front overhangs can accommodate larger engines. Large overhangs also contribute to safety due to increased bulk, as well as space for crumple zones that provide defense for passengers in frontal and rear collisions.
The Porsche 911, produced since 1964, has always contained its entire flat-6 engine within its rear overhang, with the center of mass of the engine outside of the wheelbase. In the case of the 911, the rear-mounted engine allows for increased practicality in the form of a small rear row of seats that would be impossible with a mid-engined sports car.
Excessive weight that is concentrated outside of the wheelbase can interfere with accurate negotiation of corners at high speed. The rear-engined Porsche 911, with its engine far in the rear, was notorious for dangerous oversteer in its early days, and cars with engines far in the front often suffered from the opposite problem of understeer, for which many old American cars with heavy V8 engines were infamous. Front-engined Ferraris, such as the Ferrari 612 Scaglietti place their engines within the wheelbase, so as to avoid the problem of understeer. Reducing overhanging weight in sports cars is usually a priority, with the notable exception of the 911.
In contrast, the excellent handling of the Mini, with its wheels pushed far out at each corner, can be partly credited to its small overhang. The classic Mini and New MINI are both automobiles with very little overhang and thus handle very well under extreme conditions. The minimal overhang gives the Mini its bulldog-like stance.
Rear overhang may present a problem in large vehicles such as buses. Long rear overhang would require the driver to pay attention to nearby vehicles when turning at 90 degrees. Since the rear overhang is outside the wheelbase, it may hit a vehicle in the adjacent lane, especially when turning 90 degrees right (in a right-hand drive country).
Also, some specialized vehicles (such as the AM General HMMWV and the related Hummer H1) are designed with no frontal overhang, allowing it to possess incredible abilities such as climbing vertical walls. This does, however, place these vehicles' front wheels as the furthest forward point of the vehicle, which can lead to disastrous results in the event of a frontal collision.
The Porsche 914 or VW-Porsche 914 is a mid-engined sports car designed, manufactured and marketed collaboratively by Volkswagen and Porsche from 1969 until 1976. It was only available as a targa-topped two-seat roadster powered by either a flat-4 or flat-6 engine.
Steering is a system of components, linkages, and other parts that allows a driver to control the direction of a vehicle.
Understeer and oversteer are vehicle dynamics terms used to describe the sensitivity of a vehicle to steering. Oversteer is what occurs when a car turns (steers) by more than the amount commanded by the driver. Conversely, understeer is what occurs when a car steers less than the amount commanded by the driver.
Automobile handling and vehicle handling are descriptions of the way a wheeled vehicle responds and reacts to the inputs of a driver, as well as how it moves along a track or road. It is commonly judged by how a vehicle performs particularly during cornering, acceleration, and braking as well as on the vehicle's directional stability when moving in steady state condition.
In automotive design, a front-engine, front-wheel-drive (FWD) layout, or FF layout, places both the internal combustion engine and driven roadwheels at the front of the vehicle.
In automotive design, an RR, or rear-engine, rear-wheel-drive layout places both the engine and drive wheels at the rear of the vehicle. In contrast to the RMR layout, the center of mass of the engine is between the rear axle and the rear bumper. Although very common in transit buses and coaches due to the elimination of the drive shaft with low-floor buses, this layout has become increasingly rare in passenger cars.
In automotive design, an RMR, or rear mid-engine, rear-wheel-drive layout is one in which the rear wheels are driven by an engine placed with its center of gravity in front of the rear axle, and thus right behind the passenger compartment. Nowadays more frequently called 'RMR', to acknowledge that certain sporty or performance focused front-engined cars are also "mid-engined", by having the main engine mass behind the front axle, RMR layout cars were previously just called MR, or mid-engine, rear-wheel-drive layout), because the nuance between distinctly front-engined vs. front mid-engined cars often remained undiscussed.
In both road and rail vehicles, the wheelbase is the horizontal distance between the centers of the front and rear wheels. For road vehicles with more than two axles, the wheelbase is the distance between the steering (front) axle and the centerpoint of the driving axle group. In the case of a tri-axle truck, the wheelbase would be the distance between the steering axle and a point midway between the two rear axles.
In automotive engineering, a mid-engine layout describes the placement of an automobile engine in front of the rear-wheel axles, but behind the front axle.
An anti-roll bar is a part of many automobile suspensions that helps reduce the body roll of a vehicle during fast cornering or over road irregularities. It connects opposite (left/right) wheels together through short lever arms linked by a torsion spring. An anti-roll bar increases the suspension's roll stiffness—its resistance to roll in turns—independent of its spring rate in the vertical direction. The first stabilizer bar patent was awarded to Canadian inventor Stephen Coleman of Fredericton, New Brunswick on April 22, 1919.
Wheel alignment, which is sometimes referred to as breaking or tracking, is part of standard automobile maintenance that consists of adjusting the angles of wheels to the car manufacturer specifications. The purpose of these adjustments is to reduce tire wear and to ensure that vehicle travel is straight and true. Alignment angles can also be altered beyond the maker's specifications to obtain a specific handling characteristic. Motorsport and off-road applications may call for angles to be adjusted well beyond normal, for a variety of reasons.
A glossary of terms relating to automotive design.
The Jeep Hurricane is a bespoke custom concept vehicle that was unveiled at the 2005 North American International Auto Show in Detroit by American automaker Jeep. Its principal exterior designer was Aaron Pizzuti. The concept went on to win IDEA Silver Award, a Popular Science "Best of what's new" award, and an Autoweek Editor's Choice award in the "Most Fun" category.
The CLEVER is a type of tilting three-wheeled motor vehicle that was developed in a collaboration between the University of Bath, BMW and a number of other partners from across Europe. CLEVER is designed as an alternative to conventional means of personal urban transport. The narrow body endows it with some of the manoeuvrability and congestion avoiding capability of a motorcycle, whilst offering comparable weather and impact protection to a car. Carbon emissions are reduced as a function of low weight and a small frontal area. The narrow track width requires that CLEVER tilts into corners to maintain stability; thus it is fitted with a Direct Tilt Control (DTC) system that uses hydraulic actuators linking the cabin to the non-tilting rear engine module.
Dante Giacosa was an Italian automobile designer and engineer responsible for a range of Italian automobile designs — and for refining the front-wheel drive layout to an industry-standard configuration.
The following outline is provided as an overview of and topical guide to automobiles:
Bump steer is the term for the tendency of the wheel of a car to steer itself as it moves through the suspension stroke.
In automotive design, an M4, or Mid-engine, Four-wheel-drive layout places the internal combustion engine in the middle of the vehicle, between both axles and drives all four road wheels.
Breakover angle is the maximum possible supplementary angle that a vehicle, with at least one forward wheel and one rear wheel, can drive over without the apex of that angle touching any point of the vehicle other than the wheels. This definition is contingent upon the wheels being in continuous contact with the supporting surface(s). Breakover angle differs from ground clearance, which is the shortest distance between the ground and lowest point on the vehicle.
The Vivaquatre is a car produced by Renault between 1932 and 1939. Its large 4-cylinder engine placed it initially in the 10CV car tax class, though a larger engine later made it a contender in the 11CV class.
