Pervious concrete

Last updated
A pervious concrete street Wikipedia PrvsC.JPG
A pervious concrete street

Pervious concrete (also called porous concrete, permeable concrete, no fines concrete and porous pavement) is a special type of concrete with a high porosity used for concrete flatwork applications that allows water from precipitation and other sources to pass directly through, thereby reducing the runoff from a site and allowing groundwater recharge.

Contents

Pervious concrete is made using large aggregates with little to no fine aggregates. The concrete paste then coats the aggregates and allows water to pass through the concrete slab. Pervious concrete is traditionally used in parking areas, areas with light traffic, residential streets, pedestrian walkways, and greenhouses. [1] [2] It is an important application for sustainable construction and is one of many low impact development techniques used by builders to protect water quality.

History

Pervious concrete was first used in the 1800s in Europe as pavement surfacing and load bearing walls. [3] Cost efficiency was the main motive due to a decreased amount of cement. [3] It became popular again in the 1920s for two storey homes in Scotland and England. It became increasingly viable in Europe after WWII due to the scarcity of cement. It did not become as popular in the US until the 1970s. [3] In India it became popular in 2000.[ citation needed ]

Stormwater management

The proper utilization of pervious concrete is a recognized Best Management Practice by the U.S. Environmental Protection Agency (EPA) for providing first flush pollution control and stormwater management. [4] As regulations further limit stormwater runoff, it is becoming more expensive for property owners to develop real estate, due to the size and expense of the necessary drainage systems. Pervious concrete lowers the NRCS Runoff Curve Number or CN by retaining stormwater on site. This allows the planner/designer to achieve pre-development stormwater goals for pavement intense projects. Pervious concrete reduces the runoff from paved areas, which reduces the need for separate stormwater retention ponds and allows the use of smaller capacity storm sewers. [5] This allows property owners to develop a larger area of available property at a lower cost. Pervious concrete also naturally filters storm water [6] and can reduce pollutant loads entering into streams, ponds, and rivers. [7]

Pervious concrete functions like a storm water infiltration basin and allows the storm water to infiltrate the soil over a large area, thus facilitating recharge of precious groundwater supplies locally. [5] All of these benefits lead to more effective land use. Pervious concrete can also reduce the impact of development on trees. A pervious concrete pavement allows the transfer of both water and air to root systems to help trees flourish even in highly developed areas. [5]

Properties

Pervious concrete consists of cement, coarse aggregate (size should be 9.5 mm to 12.5 mm) and water with little to no fine aggregates. The addition of a small amount of sand will increase the strength. The mixture has a water-to-cement ratio of 0.28 to 0.40 with a void content of 15 to 25 percent. [8]

The correct quantity of water in the concrete is critical. A low water to cement ratio will increase the strength of the concrete, but too little water may cause surface failure. A proper water content gives the mixture a wet-metallic appearance. As this concrete is sensitive to water content, the mixture should be field checked. [9] Entrained air may be measured by a Rapid Air system, where the concrete is stained black and sections are analyzed under a microscope. [10]

A common flatwork form has riser strips on top such that the screed is 3/8-1/2 inches (9 to 12 mm) above final pavement elevation. Mechanical screeds are preferable to manual. The riser strips are removed to guide compaction. Immediately after screeding, the concrete is compacted to improve the bond and smooth the surface. Excessive compaction of pervious concrete results in higher compressive strength, but lower porosity (and thus lower permeability). [11]

Jointing varies little from other concrete slabs. Joints are tooled with a rolling jointing tool prior to curing or saw cut after curing. Curing consists of covering concrete with 6 mil plastic sheeting within 20 minutes of concrete discharge. [12] However, this contributes to a substantial amount of waste sent to landfills. Alternatively, preconditioned absorptive lightweight aggregate as well as internal curing admixture (ICA) have been used to effectively cure pervious concrete without waste generation. [13] [14]

Testing and inspection

Pervious concrete has a common strength of 600–1,500 pounds per square inch (4.1–10.3 MPa) though strengths up to 4,000 psi (28 MPa) can be reached. There is no standardized test for compressive strength. [15] Acceptance is based on the unit weight of a sample of poured concrete using ASTM standard no. C1688. [16] An acceptable tolerance for the density is plus or minus 5 pounds (2.3 kg) of the design density.[ clarification needed ] Slump and air content tests are not applicable to pervious concrete because of the unique composition. The designer of a storm water management plan should ensure that the pervious concrete is functioning properly through visual observation of its drainage characteristics prior to opening of the facility.[ citation needed ]

Cold climates

Concerns over the resistance to the freeze-thaw cycle have limited the use of pervious concrete in cold weather environments. [17] The rate of freezing in most applications is dictated by the local climate. Entrained air may help protect the paste as it does in regular concrete. [10] The addition of a small amount of fine aggregate to the mixture increases the durability of the pervious concrete. [18] [19] [20] [ clarification needed ] Avoiding saturation during the freeze cycle is the key to the longevity of the concrete. [21] Related, having a well prepared 8 to 24 inch (200 to 600 mm) sub-base and a good drainage preventing water stagnation will reduce the possibility of freeze-thaw damage. [21]

Using permeable concrete for pavements can make them safer for pedestrians in the winter because water won't settle on the surface and freeze leading to dangerously icy conditions. Roads can also be made safer for cars by the use of permeable concrete as the reduction in the formation of standing water will reduce the possibility of aquaplaning, and porous roads will also reduce tire noise. [22]

Maintenance

To prevent reduction in permeability, pervious concrete needs to be cleaned regularly. Cleaning can be accomplished through wetting the surface of the concrete and vacuum sweeping. [12] [23]

See also

Related Research Articles

<span class="mw-page-title-main">Concrete</span> Composite construction material

Concrete is a composite material composed of aggregate bonded together with a fluid cement that cures over time. Concrete is the second-most-used substance in the world after water, and is the most widely used building material. Its usage worldwide, ton for ton, is twice that of steel, wood, plastics, and aluminium combined.

Energy-efficient landscaping is a type of landscaping designed for the purpose of conserving energy. There is a distinction between the embedded energy of materials and constructing the landscape, and the energy consumed by the maintenance and operations of a landscape.

Pavement or paving may refer to:

<span class="mw-page-title-main">Road surface</span> Road covered with durable surface material

A road surface or pavement is the durable surface material laid down on an area intended to sustain vehicular or foot traffic, such as a road or walkway. In the past, gravel road surfaces, macadam, hoggin, cobblestone and granite setts were extensively used, but these have mostly been replaced by asphalt or concrete laid on a compacted base course. Asphalt mixtures have been used in pavement construction since the beginning of the 20th century and are of two types: metalled (hard-surfaced) and unmetalled roads. Metalled roadways are made to sustain vehicular load and so are usually made on frequently used roads. Unmetalled roads, also known as gravel roads or dirt roads, are rough and can sustain less weight. Road surfaces are frequently marked to guide traffic.

<span class="mw-page-title-main">Asphalt concrete</span> Composite material used for paving

Asphalt concrete is a composite material commonly used to surface roads, parking lots, airports, and the core of embankment dams. Asphalt mixtures have been used in pavement construction since the beginning of the twentieth century. It consists of mineral aggregate bound together with bitumen, laid in layers, and compacted.

<span class="mw-page-title-main">Permeable paving</span> Roads built with water-pervious materials

Permeable paving surfaces are made of either a porous material that enables stormwater to flow through it or nonporous blocks spaced so that water can flow between the gaps. Permeable paving can also include a variety of surfacing techniques for roads, parking lots, and pedestrian walkways. Permeable pavement surfaces may be composed of; pervious concrete, porous asphalt, paving stones, or interlocking pavers. Unlike traditional impervious paving materials such as concrete and asphalt, permeable paving systems allow stormwater to percolate and infiltrate through the pavement and into the aggregate layers and/or soil below. In addition to reducing surface runoff, permeable paving systems can trap suspended solids, thereby filtering pollutants from stormwater.

<span class="mw-page-title-main">Pavers (flooring)</span> Stone or tile structure which can serve as floor; pavement type with solid blocks

A paver is a paving stone, tile, brick or brick-like piece of concrete commonly used as exterior flooring. They are generally placed on top of a foundation which is made of layers of compacted stone and sand. The pavers are placed in the desired pattern and the space between pavers is then filled with a polymeric sand. No actual adhesive or retaining method is used other than the weight of the paver itself except edging. Pavers can be used to make roads, driveways, patios, walkways and other outdoor platforms.

<span class="mw-page-title-main">Impervious surface</span> Artificial structures such as pavements covered with water-tight materials

Impervious surfaces are mainly artificial structures—such as pavements that are covered by water-resistant materials such as asphalt, concrete, brick, stone—and rooftops. Soils compacted by urban development are also highly impervious.

The United States Environmental Protection Agency (EPA) Storm Water Management Model (SWMM) is a dynamic rainfall–runoff–subsurface runoff simulation model used for single-event to long-term (continuous) simulation of the surface/subsurface hydrology quantity and quality from primarily urban/suburban areas.

<span class="mw-page-title-main">Rain garden</span> Runoff reducing landscaping method

Rain gardens, also called bioretention facilities, are one of a variety of practices designed to increase rain runoff reabsorption by the soil. They can also be used to treat polluted stormwater runoff. Rain gardens are designed landscape sites that reduce the flow rate, total quantity, and pollutant load of runoff from impervious urban areas like roofs, driveways, walkways, parking lots, and compacted lawn areas. Rain gardens rely on plants and natural or engineered soil medium to retain stormwater and increase the lag time of infiltration, while remediating and filtering pollutants carried by urban runoff. Rain gardens provide a method to reuse and optimize any rain that falls, reducing or avoiding the need for additional irrigation. A benefit of planting rain gardens is the consequential decrease in ambient air and water temperature, a mitigation that is especially effective in urban areas containing an abundance of impervious surfaces that absorb heat in a phenomenon known as the heat-island effect.

<span class="mw-page-title-main">Sustainable drainage system</span>

Sustainable drainage systems are a collection of water management practices that aim to align modern drainage systems with natural water processes and are part of a larger green infrastructure strategy. SuDS efforts make urban drainage systems more compatible with components of the natural water cycle such as storm surge overflows, soil percolation, and bio-filtration. These efforts hope to mitigate the effect human development has had or may have on the natural water cycle, particularly surface runoff and water pollution trends.

Water reducers are special chemical products added to a concrete mixture before it is poured. They are from the same family of products as retarders. The first class of water reducers was the lignosulfonates which has been used since the 1930s. These inexpensive products were derived from wood and paper industry, but are now advantageously replaced by other synthetic sulfonate and polycarboxylate, also known as superplasticizers.

Polymer concrete, also known as Epoxy Granite, is a type of concrete that uses a polymer to replace lime-type cements as a binder. In some cases the polymer is used in addition to Portland cement to form Polymer Cement Concrete (PCC) or Polymer Modified Concrete (PMC). Polymers in concrete have been overseen by Committee 548 of the American Concrete Institute since 1971.

<span class="mw-page-title-main">Types of concrete</span> Building material consisting of aggregates cemented by a binder

Concrete is produced in a variety of compositions, finishes and performance characteristics to meet a wide range of needs.

Concrete has relatively high compressive strength, but significantly lower tensile strength. The compressive strength is typically controlled with the ratio of water to cement when forming the concrete, and tensile strength is increased by additives, typically steel, to create reinforced concrete. In other words we can say concrete is made up of sand, ballast, cement and water.

<span class="mw-page-title-main">Water-sensitive urban design</span> Integrated approach to urban water cycle

Water-sensitive urban design (WSUD) is a land planning and engineering design approach which integrates the urban water cycle, including stormwater, groundwater, and wastewater management and water supply, into urban design to minimise environmental degradation and improve aesthetic and recreational appeal. WSUD is a term used in the Middle East and Australia and is similar to low-impact development (LID), a term used in the United States; and Sustainable Drainage System (SuDS), a term used in the United Kingdom.

The environmental impact of concrete, its manufacture, and its applications, are complex, driven in part by direct impacts of construction and infrastructure, as well as by CO2 emissions; between 4-8% of total global CO2 emissions come from concrete. Many depend on circumstances. A major component is cement, which has its own environmental and social impacts and contributes largely to those of concrete.

<span class="mw-page-title-main">Low-impact development (U.S. and Canada)</span>

Low-impact development (LID) is a term used in Canada and the United States to describe a land planning and engineering design approach to manage stormwater runoff as part of green infrastructure. LID emphasizes conservation and use of on-site natural features to protect water quality. This approach implements engineered small-scale hydrologic controls to replicate the pre-development hydrologic regime of watersheds through infiltrating, filtering, storing, evaporating, and detaining runoff close to its source. Green infrastructure investments are one approach that often yields multiple benefits and builds city resilience.

A runoff footprint is the total surface runoff that a site produces over the course of a year. According to the United States Environmental Protection Agency (EPA) stormwater is "rainwater and melted snow that runs off streets, lawns, and other sites". Urbanized areas with high concentrations of impervious surfaces like buildings, roads, and driveways produce large volumes of runoff which can lead to flooding, sewer overflows, and poor water quality. Since soil in urban areas can be compacted and have a low infiltration rate, the surface runoff estimated in a runoff footprint is not just from impervious surfaces, but also pervious areas including yards. The total runoff is a measure of the site’s contribution to stormwater issues in an area, especially in urban areas with sewer overflows. Completing a runoff footprint for a site allows a property owner to understand what areas on his or her site are producing the most runoff and what scenarios of stormwater green solutions like rain barrels and rain gardens are most effective in mitigating this runoff and its costs to the community.

<span class="mw-page-title-main">Nanoconcrete</span>

Nanoconcrete is a form of concrete that contains Portland cement particles that are no greater than 100 μm and particles of silica no greater than 500 μm, which fill voids that would otherwise occur in normal concrete, thereby substantially increasing the material's strength. It is also a product of high-energy mixing (HEM) of conventional cement, sand and water which is a bottom-up approach of nano technology.

References

  1. ↑ Report on Pervious Concrete. American Concrete Institute. 2010. ISBN   9780870313646. Archived from the original on 2012-03-14. Retrieved 2012-10-03. Report No. 522R-10.
  2. ↑ "Pervious Ready Mix Concrete". srmconcrete.com. Retrieved 19 November 2015.
  3. 1 2 3 Chopra, Manoj. "Compressive Strength of Pervious Concrete Pavements" (PDF). Florida Department of Transportation . Retrieved 1 October 2012.
  4. ↑ "Storm Water Technology Fact Sheet: Porous Pavement." United States Environmental Protection Agency, EPA 832-F-99-023, September 1999.
  5. 1 2 3 Ashley, Erin. "Using Pervious Concrete to Achieve LEED Points" (PDF). National Ready Mixed Concrete Association. Retrieved 1 October 2012.
  6. ↑ Majersky, Gregory. "Filtration of Polluted Waters by Pervious Concrete" (PDF). Liquid Asset Development. Retrieved 3 October 2012.
  7. ↑ "Pervious Concrete". Purinton Builders. Retrieved 3 October 2012.
  8. ↑ John T. Kevern; Vernon R. Schaefer & Kejin Wang (2011). "Mixture Proportion Development and Performance Evaluation of Pervious Concrete for Overlay Applications". Materials Journal. American Concrete Institute. 108 (4): 439–448. Archived from the original on July 7, 2013. Retrieved July 3, 2013.
  9. ↑ Desai, Dhawal (5 March 2012). "Pervious Concrete – Effect of Material Proportions on Porosity". Civil Engineering Portal. Retrieved 30 September 2012.
  10. 1 2 Kevern, John; K. Wang; V. R. Schaefer (2008). "A Novel Approach to Characterize Entrained Air Content in Pervious Concrete" (PDF). ASTM International. 5 (2).
  11. ↑ Kevern, John. "Effect of Compaction Energy on Pervious Concrete Properties". RMC Research Foundation. Retrieved 1 October 2012.
  12. 1 2 Kevern, John. "Operation and Maintenance of Pervious Concrete Pavements" (PDF). Retrieved 1 October 2012.
  13. ↑ "Internal Curing with HydroMax". ProCure. Retrieved 1 October 2012.
  14. ↑ Kevern, J.T. and Farney, C. "Reducing Curing Requirements for Pervious Concrete Using a Superabsorbent Polymer for Internal Curing." Transportation Research Record: Journal of the Transportation Research Board (TRB), Construction 2012, Transportation Research Board of the National Academies, Washington D.C.
  15. ↑ "Specification for Pervious Concrete." ACI 522.1-08. American Concrete Institute, Farmington Hills, MI, 7pp.
  16. ↑ ASTM International. "Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete." Standard No. C1688.
  17. ↑ Vernon R. Schaefer; Keijin Wang; Muhammad T. Suleiman; John T. Kevern (2006). "Mix Design Development for Pervious Concrete in Cold Weather Climates". Ames, IA: Iowa State University. National Concrete Pavement Technology Center. Report No. 2006-01.
  18. ↑ Kevern, John Tristan (2006). Mix Design Development for Portland Cement Pervious Concrete in Cold Weather Climates. Master’s Thesis, Iowa State University, Ames, Iowa, 155 pages.
  19. ↑ Kevern, John; K. Wang; V.R. Schaefer (2008). "Design of Pervious Concrete Mixtures". Iowa State University.
  20. ↑ Mata, Luis Alexander (2008). Sedimentation of Pervious Concrete Pavement Systems. PhD Dissertation, North Carolina State University, Raleigh, North Carolina. Also available as PCA SN3104.
  21. 1 2 "Pervious Concrete and Freeze-Thaw". Concrete Technology E-Newsletter. PCA. Retrieved 1 June 2023.
  22. ↑ Environmental, Oakshire (2021-05-24). "Flood Risk Assessment". Oakshire Environmental. Retrieved 2021-05-24.
  23. ↑ "Prevention". Charger Enterprises. Archived from the original on 28 August 2008. Retrieved 30 September 2012.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.