Al-Ca composite

Last updated

Al-Ca composite is a high-conductivity, high-strength, lightweight composite consisting of sub-micron-diameter pure calcium metal filaments embedded inside a pure aluminium metal matrix. The material is still in the development phase, but it has potential use as an overhead high-voltage power transmission conductor. [1] It could also be used wherever an exceptionally light, high-strength conductor is needed. Its physical properties make it especially well-suited for DC transmission. Compared with conventional conductors such as aluminium-conductor steel-reinforced cable (ACSR), all aluminium alloy conductors (AAAC), aluminium conductor alloy reinforced (ACAR), aluminium conductor composite reinforced ACCR and ACCC conductor that conduct alternating current well and DC current somewhat less well (due to the skin effect), Al-Ca conductor is essentially a single uniform material with high DC conductivity, allowing the core strands and the outer strands of a conductor cable to all be the same wire type. This conductor is inherently strong so that there is no need for a strong (usually poorly conductive) core to support its own weight as is done in conventional conductors. This eliminates the "bird caging", spooling, and thermal fatigue problems caused by thermal expansion coefficient mismatch between the core and outer strands. The Al-Ca phase interfaces strengthen the composite substantially, [2] [3] but do not have a noticeable effect on restricting the mean free path of electrons, which gives the composite both high strength and high conductivity, [4] a combination that is normally difficult to achieve with both pure metals and alloys. [5] The high strength and light weight could reduce the number of towers needed per kilometer for long distance transmission lines. [6] Since towers and their foundations often account for 50% of a powerline's construction cost, building fewer towers would save a substantial fraction of total construction costs. The high strength also could increase transmission reliability in wind/ice loading situations. The high conductivity has the potential to reduce Ohmic losses.

Al-Ca composite conductor was invented by Russell and Anderson at Ames Laboratory of the U.S. Department of Energy with the goal of developing the next generation power transmission cables. [7] Al/Ca composite is produced by powder metallurgy and severe deformation processing (extrusion, swaging, wire drawing). This process would be roughly two to three times more expensive than conventional melt processing for ACSR. But the cost saving on tower construction is projected to be substantially larger than the extra cost of the conducting cables. During deformation processing, the Ca powder particles deform into filaments surrounded by the Al matrix, which avoids exposing calcium, a reactive element, to air and moisture. The corrosion resistance of this composite has been found to be similar to that of pure aluminium.

Al-Ca composite has good microstructural stability even above 300 °C. [8] The formation of intermetallic compounds at the interface would stabilize the microstructure to avoid the degradation of its various properties during exposure to elevated temperatures, [9] such as those encountered during emergency overload situations.

Newest development

An Al/Ca (20 vol%) nanofilamentary metal-metal composite was produced by powder metallurgy and severe plastic deformation. [10] Fine Ca metal powders (~200 μm) were produced by centrifugal atomization, mixed with pure Al powder, and deformed by warm extrusion, swaging, and wire drawing to a true strain of 12.9. [11] The Ca powder particles became fine Ca nanofilaments that reinforce the composite substantially by interface strengthening. The conductivity of the composite is slightly lower than the rule-of-mixtures prediction due to minor quantities of impurity inclusions. The elevated temperature performance of this composite was also evaluated by differential scanning calorimetry and resistivity measurements.

The ultimate tensile strength is as high as 480 MPa, twice as that of ACSR.

The electrical conductivity 33.02 (μΩ m)−1 is higher than most current commonly used conductors.

Related Research Articles

<span class="mw-page-title-main">Ceramic</span> An inorganic, nonmetallic solid prepared by the action of heat

A ceramic is any of the various hard, brittle, heat-resistant, and corrosion-resistant materials made by shaping and then firing an inorganic, nonmetallic material, such as clay, at a high temperature. Common examples are earthenware, porcelain, and brick.

In materials science, a metal matrix composite (MMC) is a composite material with fibers or particles dispersed in a metallic matrix, such as copper, aluminum, or steel. The secondary phase is typically a ceramic or another metal. They are typically classified according to the type of reinforcement: short discontinuous fibers (whiskers), continuous fibers, or particulates. There is some overlap between MMCs and cermets, with the latter typically consisting of less than 20% metal by volume. When at least three materials are present, it is called a hybrid composite. MMCs can have much higher strength-to-weight ratios, stiffness, and ductility than traditional materials, so they are often used in demanding applications. MMCs typically have lower thermal and electrical conductivity and poor resistance to radiation, limiting their use in the very harshest environments.

In materials science, superplasticity is a state in which solid crystalline material is deformed well beyond its usual breaking point, usually over about 400% during tensile deformation. Such a state is usually achieved at high homologous temperature. Examples of superplastic materials are some fine-grained metals and ceramics. Other non-crystalline materials (amorphous) such as silica glass and polymers also deform similarly, but are not called superplastic, because they are not crystalline; rather, their deformation is often described as Newtonian fluid. Superplastically deformed material gets thinner in a very uniform manner, rather than forming a "neck" that leads to fracture. Also, the formation of microvoids, which is another cause of early fracture, is inhibited. Superplasticity must not be confused with superelasticity.

A cermet is a composite material composed of ceramic and metal materials.

<span class="mw-page-title-main">Titanium diboride</span> Chemical compound

Titanium diboride (TiB2) is an extremely hard ceramic which has excellent heat conductivity, oxidation stability and wear resistance. TiB2 is also a reasonable electrical conductor, so it can be used as a cathode material in aluminium smelting and can be shaped by electrical discharge machining.

<span class="mw-page-title-main">Metal foam</span> Porous material made from a metal

In materials science, a metal foam is a material or structure consisting of a solid metal with gas-filled pores comprising a large portion of the volume. The pores can be sealed or interconnected. The defining characteristic of metal foams is a high porosity: typically only 5–25% of the volume is the base metal. The strength of the material is due to the square–cube law.

Aluminium carbide, chemical formula Al4C3, is a carbide of aluminium. It has the appearance of pale yellow to brown crystals. It is stable up to 1400 °C. It decomposes in water with the production of methane.

<span class="mw-page-title-main">Gold–aluminium intermetallic</span> Any intermetallic compound of gold and aluminium

Gold–aluminium intermetallic is a type of intermetallic compound of gold and aluminium that usually forms at contacts between the two metals. Gold–aluminium intermetallic have different properties from the individual metals, such as low conductivity and high melting point depending on their composition. Due to the difference of density between the metals and intermetallics, the growth of the intermetallic layers causes reduction in volume, and therefore creates gaps in the metal near the interface between gold and aluminium.

<span class="mw-page-title-main">Aluminium-conductor steel-reinforced cable</span> Type of overhead power line conductor

Aluminium conductor steel-reinforced cable (ACSR) is a type of high-capacity, high-strength stranded conductor typically used in overhead power lines. The outer strands are high-purity aluminium, chosen for its good conductivity, low weight, low cost, resistance to corrosion and decent mechanical stress resistance. The centre strand is steel for additional strength to help support the weight of the conductor. Steel is of higher strength than aluminium which allows for increased mechanical tension to be applied on the conductor. Steel also has lower elastic and inelastic deformation due to mechanical loading as well as a lower coefficient of thermal expansion under current loading. These properties allow ACSR to sag significantly less than all-aluminium conductors. As per the International Electrotechnical Commission (IEC) and The CSA Group naming convention, ACSR is designated A1/S1A.

<span class="mw-page-title-main">Solid</span> State of matter

Solid is one of the four fundamental states of matter along with liquid, gas, and plasma. The molecules in a solid are closely packed together and contain the least amount of kinetic energy. A solid is characterized by structural rigidity and resistance to a force applied to the surface. Unlike a liquid, a solid object does not flow to take on the shape of its container, nor does it expand to fill the entire available volume like a gas. The atoms in a solid are bound to each other, either in a regular geometric lattice, or irregularly. Solids cannot be compressed with little pressure whereas gases can be compressed with little pressure because the molecules in a gas are loosely packed.

Beryllium-aluminum alloy an alloy that consists of 62% beryllium and 38% aluminum, by weight, corresponding approximately to an empirical formula of Al2Be. It was first developed in the 1960s by the Lockheed Missiles and Space Company, who called it Lockalloy, and used as a structural metal in the aerospace industry because of its high specific strength and stiffness. The material was used in the Lockheed YF12 and LGM-30 Minuteman missile systems. In the 1970s production difficulties limited the material to a few specialized uses and by the mid 1970s Lockalloy was no longer commercially available.

AlSiC, pronounced "alsick", is a metal matrix composite consisting of aluminium matrix with silicon carbide particles. It has high thermal conductivity, and its thermal expansion can be adjusted to match other materials, e.g. silicon and gallium arsenide chips and various ceramics. It is chiefly used in microelectronics as substrate for power semiconductor devices and high density multi-chip modules, where it aids with removal of waste heat.

<span class="mw-page-title-main">Friction stir processing</span>

Friction stir processing (FSP) is a method of changing the properties of a metal through intense, localized plastic deformation. This deformation is produced by forcibly inserting a non-consumable tool into the workpiece, and revolving the tool in a stirring motion as it is pushed laterally through the workpiece. The precursor of this technique, friction stir welding, is used to join multiple pieces of metal without creating the heat affected zone typical of fusion welding.

<span class="mw-page-title-main">Carbon nanotube metal matrix composite</span>

Carbon nanotube metal matrix composites (CNT-MMC) are an emerging class of new materials that mix carbon nanotubes into metals and metal alloys to take advantage of the high tensile strength and electrical conductivity of carbon nanotube materials.

<span class="mw-page-title-main">Copper conductor</span> Electrical wire or other conductor made of copper

Copper has been used in electrical wiring since the invention of the electromagnet and the telegraph in the 1820s. The invention of the telephone in 1876 created further demand for copper wire as an electrical conductor.

Ultra-high-temperature ceramics (UHTCs) are a type of refractory ceramics that can withstand extremely high temperatures without degrading, often above 2,000 °C. They also often have high thermal conductivities and are highly resistant to thermal shock, meaning they can withstand sudden and extreme changes in temperature without cracking or breaking. Chemically, they are usually borides, carbides, nitrides, and oxides of early transition metals.

ACCC is a registered trade mark for a type of "high-temperature low-sag" (HTLS) overhead power line conductor.

<span class="mw-page-title-main">Dissimilar friction stir welding</span>

Dissimilar friction stir welding (DFSW) is the application of friction stir welding (FSW), invented in The Welding Institute (TWI) in 1991, to join different base metals including aluminum, copper, steel, titanium, magnesium and other materials. It is based on solid state welding that means there is no melting. DFSW is based on a frictional heat generated by a simple tool in order to soften the materials and stir them together using both tool rotational and tool traverse movements. In the beginning, it is mainly used for joining of aluminum base metals due to existence of solidification defects in joining them by fusion welding methods such as porosity along with thick Intermetallic compounds. DFSW is taken into account as an efficient method to join dissimilar materials in the last decade. There are many advantages for DFSW in compare with other welding methods including low-cost, user-friendly, and easy operation procedure resulting in enormous usages of friction stir welding for dissimilar joints. Welding tool, base materials, backing plate (fixture), and a milling machine are required materials and equipment for DFSW. On the other hand, other welding methods, such as Shielded Metal Arc Welding (SMAW) typically need highly professional operator as well as quite expensive equipment.

Nanotech metallurgy is an emerging interdisciplinary domain of materials science and engineering, manufacturing, and nanoscience and engineering to study how nanophases can be applied to significantly improve the processing/manufacturing, micro/nano-structures, and physical/chemical/mechanical behaviors of metals and alloys. This definition was first proposed by Xiaochun Li at the University of California, Los Angeles in 2018, although nanotechnology in metallurgy can be dated back some centuries to the role of precipitates in materials such as Wootz steel and Damascus steel.

<span class="mw-page-title-main">Lithium aluminium germanium phosphate</span> Chemical compound

Lithium aluminium germanium phosphate, typically known with the acronyms LAGP or LAGPO, is an inorganic ceramic solid material whose general formula is Li
1+xAl
xGe
2-x(PO
4)
3. LAGP belongs to the NASICON family of solid conductors and has been applied as a solid electrolyte in all-solid-state lithium-ion batteries. Typical values of ionic conductivity in LAGP at room temperature are in the range of 10–5 - 10–4 S/cm, even if the actual value of conductivity is strongly affected by stoichiometry, microstructure, and synthesis conditions. Compared to lithium aluminium titanium phosphate (LATP), which is another phosphate-based lithium solid conductor, the absence of titanium in LAGP improves its stability towards lithium metal. In addition, phosphate-based solid electrolytes have superior stability against moisture and oxygen compared to sulfide-based electrolytes like Li
10GeP
2S
12 (LGPS) and can be handled safely in air, thus simplifying the manufacture process. Since the best performances are encountered when the stoichiometric value of x is 0.5, the acronym LAGP usually indicates the particular composition of Li
1.5Al
0.5Ge
1.5(PO
4)
3, which is also the typically used material in battery applications.

References

  1. ↑ Tian L, Anderson I, Riedemann T, Russell A, Kim H. Electr Pow Syst Res 2013;105:105.
  2. ↑ Tian, Liang; Russell, Alan; Anderson, Iver (2014). "A dislocation-based, strain–gradient–plasticity strengthening model for deformation processed metal–metal composites". Journal of Materials Science. 49 (7): 2787. Bibcode:2014JMatS..49.2787T. doi:10.1007/s10853-013-7982-5.
  3. ↑ Bevk, J.; Harbison, James P.; Bell, Joseph L. (1978). "Anomalous increase in strength of in situ formed Cu-Nb multifilamentary composites". Journal of Applied Physics. 49 (12): 6031. Bibcode:1978JAP....49.6031B. doi:10.1063/1.324573.
  4. ↑ Tian, Liang; Anderson, Iver; Riedemann, Trevor; Russell, Alan (2014). "Modeling the electrical resistivity of deformation processed metal–metal composites". Acta Materialia. 77: 151–161. Bibcode:2014AcMat..77..151T. doi:10.1016/j.actamat.2014.06.013.
  5. ↑ Russell, A. M.; Chumbley, L. S.; Tian, Y. (2000). "Deformation Processed Metal-Metal Composites". Advanced Engineering Materials. 2 (1–2): 11–22. doi:10.1002/(SICI)1527-2648(200002)2:1/2<11::AID-ADEM11>3.0.CO;2-Z.
  6. ↑ Padiyar,K.R. (2011) HVDC Power Transmission Systems, second ed., New Academic Science, Tunbridge Wells, Kent, UK.
  7. ↑ Russell A.M., Anderson, I.E., Kim, H.J., and Frerichs, A.E. (2014) U.S. patent 8,647,536 "Aluminum/Alkaline Earth Metal Composites And Method For Producing Same"
  8. ↑ Tian, Liang; Kim, Hyongjune; Anderson, Iver; Russell, Alan (2013). "The microstructure-strength relationship in a deformation processed Al–Ca composite". Materials Science and Engineering: A. 570: 106–113. doi:10.1016/j.msea.2013.01.062.
  9. ↑ Tian, Liang; Russell, Alan (2014). "Phase field study of interfacial diffusion-driven spheroidization in a composite comprised of two mutually insoluble phases". The Journal of Chemical Physics. 140 (12): 124706. Bibcode:2014JChPh.140l4706T. doi:10.1063/1.4869296. PMID   24697469.
  10. ↑ Tian, Liang; Russell, Alan; Riedemann, Trevor; Mueller, Soeren; Anderson, Iver (2017-04-06). "A deformation-processed Al-matrix/Ca-nanofilamentary composite with low density, high strength, and high conductivity". Materials Science and Engineering: A. 690: 348–354. doi: 10.1016/j.msea.2017.03.010 .
  11. ↑ Tian, Liang; Anderson, Iver; Riedemann, Trevor; Russell, Alan (2017-02-15). "Production of fine calcium powders by centrifugal atomization with rotating quench bath". Powder Technology. 308: 84–93. doi: 10.1016/j.powtec.2016.12.011 .
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.