Etna (sternwheeler)

Last updated
Etna (sternwheeler) circa 1915.jpg
Etna on the Lewis River, pushing a barge, sometime between 1906 and 1911.
History
NameEtna
OwnerEtna Transportation Co.
OperatorLurlie Gray
Route Lewis River
In service1906
Out of service1919
IdentificationU.S. #203622
FateSunk by drifting logs
General characteristics
Tonnage41 gross register tons
Length60 ft (18.29 m)
Beam11.4 ft (3.47 m)
Depth3.6 ft (1.10 m) depth of hold
Installed power30 hp gasoline engine (1906-1907); replaced by twin steam engines, horizontally mounted, cylinder bore 5.0 in (127.0 mm) and stroke of 2.67 ft (0.81 m).
Propulsionstern-wheel
Capacity10 tons deadweight of freight

Etna was a steamboat that operated on the Lewis and Lake rivers of southwestern Washington from 1906 to 1919. As built in 1906 Etna was originally powered by a gasoline engine, but in 1907 it was converted to steam-powered vessel.

Contents

Etna was named after Etna, Washington, a settlement on the south side of the Lewis River, in Clark County. Etna's principal activity was supporting the logging camps and lumber mills in the Lewis river area.

Etna was a light draft vessel which was essential for operating in the shallow water of the upper Lewis River. Even then, operation of Etna was substantially affected by the rise and fall of river levels, which were generally seasonal.

Small craft like Etna on the Columbia River system were sometimes referred to at the time as the "mosquito fleet" [1]

Construction

Etna was built in Portland, Oregon in 1906 for Horace Campbell by the Portland shipyard of Joseph Supple. [2] [3] Campbell was a steamboat engineer with extensive experience on the Lewis and Lake rivers. [4]

Dimensions

Etna was 60 ft (18.29 m) exclusive of the extension of the deck over the stern, called the fantail, on which the stern-wheel was mounted. [2]

Etna had a beam of 11.4 ft (3.47 m) exclusive of the protective timbers along the upper sides of the hull called guards. [2] The vessel had a depth of hold of 3.6 ft (1.10 m). [2]

The overall size of the vessel was 41 gross tons (a measure of volume and not weight) and 40 registered tons. [2]

Etna could carry about 10 tons deadweight of freight. [5] The official merchant vessel registry number was 203622. [2]

Machinery

Horace Campbell, steamboat engineer and first owner of Etna, image from 1895 or earlier. Horace Campbell.jpg
Horace Campbell, steamboat engineer and first owner of Etna, image from 1895 or earlier.

The original power for Etna was a 30 horsepower gasoline engine. [6]

In August 1907, Horace Campbell had Etna converted from a gasoline engine to a steam-powered vessel. [7] The steam power plant consisted of twin high-pressure single cylinder engines, horizontally mounted, each with a cylinder bore 5.0 in (127.0 mm) and stroke of 2.67 ft (0.81 m). [2]

In December 1912, Etna Transportation Company, owners of Etna, bought an electric generator to install on the steamer. [8] Electric lights were made necessary because of the increased level of traffic on the river required the steamer to operate during darkness, particularly in the winter when the days were shorter. [8]

Career

Horace Campbell planned to use Etna on the Lewis River route in conjunction with the sternwheeler Mascot. [7] Logging camps and mills up the Lewis river depended on shallow-draft steamers like Etna to bring in supplies. [9] Etna also carried passengers. [9]

Proposed transfer to Willamette River

In June 1910, when low water barred navigation on the Willamette River above Newberg, Oregon, and government dredging operations had ceased, there was talk among the farmers along the river between Newberg and Wheatland of securing the steamer Etna, then running on the Lewis River, to carry freight on the Willamette. [5]

Low water 1910

On October 6, 1910, early rains raised the water level high enough on the north fork of the Lewis River so that Etna could navigate on the route. [10] This was about three or four weeks before the water was usually deep enough for Etna to make the trip on the north fork [10]

Grounding in 1911

In mid-February 1911, Etna struck a boulder and had to be taken to Joseph Supple’s shipyard in Portland to be repaired. [9] The repairs were complete by February 26, but the steamer still could not ascend the Lewis River because of low water, there having been no recent rain or warmer weather to melt the mountain snows. [9]

Dam construction material

In March 1911 it was "practically decided" that Etna, running under Captain Lurlie Gray, would be used to transport material and supplies to be used in construction of a power dam about 30 miles upriver from Woodland, Washington. [11] The river then stood at 3.8 feet and it was expected that Etna would have no difficulty reaching Ariel, Washington, the head of navigation. [11]

Low water 1911

On Wednesday, November 8, 1911, rainfall in the Lewis River area raised the water level sufficiently to allow Etna to make its first trip of the fall season. [12]

Increased lumber business 1912

In May 1912 the logging and lumber mill business on the Lewis River was more prosperous than it had been for a long time. [13] About a year previously, Dubois Lumber Co. of Vancouver, Washington had purchased over 40,000,000 board feet of timber about 15 miles upriver from Woodland. [13]

After much preparation, including road work, the company was reported to be ready to begin operations on Monday, May 13, 1912, with 25 to 40 men employed. [13] About 25 men arrived at Woodland on Thursday May 9, and Etna took them to the logging camp on the North Fork at Yale, 25 miles upriver from Woodland. [13]

New schedule

On Tuesday May 14, 1912, Etna went on a new schedule, running round trips on Mondays, Tuesdays, Thursdays, and Saturdays between Woodland and Ariel. [14] Previously Etna had been traveling upriver one day and returning downriver the next day. [14] The new schedule would remain in effect until the next low water season. [14]

Transport of rails

In November 1912 the Harvey Mill Company was building a logging railroad. [15] The first car for the railroad was brought in on November 6, 1912 by the steamer Etna. [15] A large shipment of rails was expected, sufficient to construct the anticipated seven miles of trackage that the company planned to build. [15]

November 6 was also the first day that the water level in the river had risen sufficiently to allow Etna to resume operations. [16] The first five cars of rails arrived at Woodland on November 20, 1912, and were placed on the river bank to be carried upriver by the steamer Etna. [17] There were expected to be a total of 15 cars worth of rails shipped in, in installments of five cars each. [17]

Sawmill transport

On December 5, 1912, a complete sawmill capable of cutting 50,000 board feet per day arrived at Woodland, intend for the North Fork Logging Company then operating at Yale, 25 miles upriver from Woodland. [18] Etna would take the new mill up to the logging camp at Yale, where the mill would be used mainly for cutting railway ties. [18]

Later career

Etna pushing a barge on the Lewis River, 1911 or earlier. Etna postcard 1911.jpg
Etna pushing a barge on the Lewis River, 1911 or earlier.

Following the summer low water season of 1914, Captain Gray of Etna expected to begin operations on the Lewis River in about the middle of September, which was the earliest possible time under normal river conditions. [19]

Dynamiting snags

In mid-December 1914, the sternwheeler Woodland, running on the north fork of the Lewis River under Capt. John W. Exon, was delayed by a day in returning to Woodland by some snags in the river at a place called Lamb’s Bar. [20] These snags had been recently exposed because of a change in the channel caused by a recent rise in the river. [20]

Captain Exon informed the United States Engineers office in Portland, and they authorized Exon to have the snags removed. [20] Captain Lurlie Gray and the steamer Etna, as well as a crew of men, were engaged to dynamite the snags. [20]

Logging camps resume operation

In January 1916, it was reported that many of the logging camps and mills on the north fork of the Lewis River which had suspended operations, some of them for several years, would resume work as soon as weather conditions improved. [21] The decline of logging work had forced Capt. Lurlie J. Gray, of the Etna, to tie up the boat. [21] With logging activity expected to resume soon, Captain Gray was getting ready to return Etna into service. [21]

In late May 1916, Capt. Gray and Etna delivered a fifth car of rails for the Dubois logging camp at Ariel. [22] Late rains and snowmelt had kept the river unusually high for that time of year. [22]

Rescue and medical transport

On August 27, 1916, Capt. Lurlie Gray rescued and resuscitated a boy, Elmer Scott, aged 12, from drowning after the boy had been drawn under a launch at Woodland by the current in the Lewis River. [23] The boy had been swimming with some friends. [23]

On February 11, 1918, George Waldron, an employee of the Tenny Logging company near Ren, on the Lewis river was seriously hurt by a flying log. [24] Waldron was taken downriver to Woodland on Etna, where he was treated by Dr. Hoffman, after which Waldron was taken to a hospital in Portland. [24]

Disposition

Etna was not worked after 1919. [2] According to a contemporaneous source, on November 18, 1918, a rise in the water level of the Lewis River at Woodland resulted in the sinking of Etna. [25] The steamer was anchored behind a jetty. [25] The water overtopped the jetty, carrying sawlogs with it. [25] These sawlogs caught on the anchor cable, pulling the steamer down. [25]

Notes

  1. ↑ "Small Craft Being Repaired -- Etna Being Rehabilitated and Eva Is Due for Overhauling". Morning Oregonian. Vol. 53, no. 16, 478. Portland, OR. September 17, 1913. p.18, col.4.
  2. 1 2 3 4 5 6 7 8 Affleck, Edward L. (2000). "Columbia River Waterways — List of Vessels". A Century of Paddlewheelers in the Pacific Northwest, the Yukon, and Alaska. Vancouver, BC: Alexander Nicholls Press. p. 13. ISBN   0-920034-08-X.
  3. ↑ "Marine Notes". Sunday Oregonian. Vol. 25, no. 31. Portland, OR. August 5, 1906. pt.2, p.15, cols.1–2.
  4. ↑ Wright, Edgar W., ed. (1895). "Finest Steamers in the Northwest Appear on Puget Sound Waters". Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. p. 379. LCCN   28001147.
  5. 1 2 "Farmers May Run Steamer — Upper Willamette Finds Itself in Need of Transportation". Morning Oregonian. Vol. 50, no. 15, 457. Portland, OR. June 11, 1910. p.18, col.1.
  6. ↑ "Steamer for Lewis River". Morning Oregonian. Vol. 25, no. 34. Portland, OR. August 26, 1906. p.10, col.2.
  7. 1 2 C.S. "Sam" Jackson, ed. (August 14, 1907). "Along the Waterfront". Oregon Daily Journal . Vol. 6, no. 138. Portland, OR: Journal Pub. Co. p.14, col.7.
  8. 1 2 "Etna to Try Electricity". Morning Oregonian (Dateline: Woodland, Wash., Dec. 11 (Special)). Vol. 52, no. 16, 241. Portland, OR. December 12, 1912. p.20, col.4.
  9. 1 2 3 4 "Low Water Halts Steamer". Morning Oregonian (Dateline: Woodland, Wash., Feb. 27 (Special)). Vol. 51, no. 15, 681. Portland, OR. February 28, 1911. p.16, cols.2–3.
  10. 1 2 "Rains Raise Lewis River". Morning Oregonian (Dateline: Woodland, Wash., Oct. 6 (Special)). Vol. 50, no. 15, 558. Portland, OR. October 7, 1910. p.8, col.2.
  11. 1 2 "Dam Supplies Go Through Woodland". Morning Oregonian (Dateline: Woodland, Wash., March 18 (Special)). Vol. 30, no. 12. Portland, OR. March 19, 1911. sec.4, p.10, col.7.
  12. ↑ "Lewis River Is Rising". Morning Oregonian (Dateline: Woodland, Wash., Nov. 10 (Special)). Vol. 51, no. 15, 901. Portland, OR. November 11, 1911. p.14, col.2.
  13. 1 2 3 4 "Lewis River Lumber Camps Active". Morning Oregonian (Dateline: Woodland, Wash., May 9 (Special)). Vol. 52, no. 16, 056. Portland, OR. May 10, 1912. p.17, cols.4–5.
  14. 1 2 3 "Steamer Etna on New Schedule". Morning Oregonian (Dateline: Woodland, Wash. May 14 (Special)). Vol. 52, no. 16, 060. Portland, OR. May 15, 1912. p.4, cols.4-5.
  15. 1 2 3 "Etna Logging Road Under Way". Morning Oregonian (Dateline: Woodland, Wash. Nov. 7 (Special)). Vol. 52, no. 16, 211. Portland, OR. November 8, 1912. p.6, cols.4-5.
  16. ↑ "Steamer Service Resumed". Morning Oregonian (Dateline: Woodland, Wash., Nov. 7 (Special)). Vol. 52, no. 16, 211. Portland, OR. November 8, 1912. p.13, col.2.
  17. 1 2 "Wild Wind Plays Pranks". Morning Oregonian (Dateline: Woodland, Wash, Nov. 20 (Special)). Vol. 52, no. 16, 222. Portland, OR. November 21, 1912. p.21, col.5.
  18. 1 2 "Yale Gets New Sawmill". Morning Oregonian (Dateline: Woodland, Wash., Dec. 5 (Special)). Vol. 52, no. 16, 236. Portland, OR. December 6, 1912. p.8, col.3.
  19. ↑ "Etna to Begin Run at Woodland". Morning Oregonian (Dateline: Woodland, Wash., Sept. 4 (Special)). Vol. 54, no. 16, 781. Portland, OR. September 5, 1914. p.16, col.4.
  20. 1 2 3 4 "Channel Near Woodland Obstructed". Sunday Oregonian (Dateline: Woodland, Wash., Dec. 12 (Special)). Vol. 33, no. 50. Portland, OR. December 13, 1914. sec.2, p.6, col.3.
  21. 1 2 3 "Logging Activities Near Woodland Await Weather Improvement". Morning Oregonian (Dateline: Woodland, Wash., Jan 20 (Special)). Vol. 55, no. 17, 212. Portland, OR. January 21, 1916. p.5, cols.5–6.
  22. 1 2 "Steel Rails Arrive at Ariel". Sunday Oregonian (Dateline: Woodland, Wash., May 27, (special)). Vol. 35, no. 22. Portland, OR. May 28, 1916. sec.1, p.9, col.2.
  23. 1 2 "Boy Bather is Rescued — Captain Lurlie Gray Saves Life of Elmer Scott at Woodland". Morning Oregonian (Dateline: Woodland, Wash. Aug. 27 (Special)). Vol. 56, no. 17, 399. Portland, OR. August 28, 1916. p.1, col.4.
  24. 1 2 "Logger Injured in Woods". Morning Oregonian (Dateline: Woodland, Wash., Feb. 12 (Special)). Vol. 58, no. 17, 856. Portland, OR. February 13, 1918. p.4, col.4.
  25. 1 2 3 4 "Rise in River Sends Steamer Down". Morning Oregonian (Dateline: Woodland, Wash, Nov. 18.). Vol. 58, no. 18, 093. Portland, OR. November 19, 1918. p.13, col.2.

Related Research Articles

<i>Gazelle</i> (1854 sidewheeler) American ship

Gazelle was an early sidewheeler on the Willamette River in what is now the U.S. state of Oregon. She did not operate long, suffering a catastrophic boiler explosion on April 8, 1854, less than a month after her trial voyage. This was the worst such explosion ever to occur in the Pacific Northwest states. The wrecked Gazelle was rebuilt and operated for a few years, first briefly as the unpowered barge Sarah Hoyt and then, with boilers installed, as the steamer Señorita. A victim of the explosion was D.P. Fuller, age 28, who is buried in Lone Fir Cemetery in Portland, Oregon.

<i>Sarah Dixon</i> (sternwheeler)

Sarah Dixon was a wooden sternwheel-driven steamboat operated by the Shaver Transportation Company on the Columbia and lower Willamette rivers from 1892 to 1926. Originally Sarah Dixon was built as a mixed use passenger and freight vessel, and was considered a prestige vessel for the time.

<i>Bonita</i> (1900 sternwheeler)

Bonita was a steamboat which operated on the Willamette and Yamhill rivers. This boat was renamed Metlako in 1902, and operated under that name until 1924 on the Columbia River and its tributaries, the Cowlitz, Lewis and Lake rivers. In 1924, Metlako was renamed B. H. Smith Jr., operating under that name until 1931, when the steamer was abandoned. As Bonita, in September 1900, this vessel was the first steamer to pass through the Yamhill locks.

<i>Albany</i> (1868 sternwheeler)

Albany was a stern-wheel driven steamboat that operated on the Willamette River from 1868 to 1875. This vessel should not be confused with the later sternwheeler Albany, which ran, also on the Willamette River, from 1896 to 1906, when it was rebuilt and renamed Georgie Burton.

<i>Robert Young</i> (sternwheeler) American stern-wheel driven steamboat

Robert Young was a stern-wheel driven steamboat that operated on the Columbia and Willamette rivers from 1918 to 1935. This vessel was originally named Nespelem, and operated under that name until 1920. From 1920 to 1935, this vessel was owned by the Western Transportation Company or one of its subsidiaries, and was employed primarily in service to paper mills.

<i>No Wonder</i> (sternwheeler)

No Wonder was a stern-wheel driven steamboat that operated on the Willamette, Columbia and Cowlitz rivers from 1889 to 1930. No Wonder was originally built in 1877 as Wonder, which was dismantled in 1888, with components being shifted over to a new hull, which when launched in late 1889 was called No Wonder.

<i>Gazelle</i> (motor vessel)

Gazelle was a gasoline powered launch that operated on the Willamette and Columbia river from 1905 to 1911. For short periods of time Gazelle was operated on the Oregon Coast, on Yaquina Bay and also as an off-shore fishing vessel, in the Coos Bay area.

<i>Mascot</i> (sternwheeler)

Mascot was a sternwheel-driven steamboat built in 1890 which operated primarily on a route running from Portland, Oregon down the Willamette and Columbia rivers to points on the Lewis and Lake rivers. Points served included the town of Woodland, Washington, on the main branch of the Lewis, and La Center, Washington on the east fork.

<i>La Center</i> (sternwheeler)

La Center was a small stern-wheel steamboat that operated from 1912 to 1931, mostly on the Lewis and Lake rivers in southwest Washington, on a route to and from Portland, Oregon along the lower Columbia and lower Willamette rivers.

<i>Northwest</i> (sternwheeler)

Northwest was a steamboat that operated on the Columbia, Cowlitz and lower Willamette rivers from 1889 to 1907. In 1907 Northwest was transferred to Alaska, where it sank on the Skeena River

<i>Jessie Harkins</i>

Jessie Harkins was a propeller-driven steamboat that operated on the Columbia River starting in 1903. It was rebuilt at least twice. Originally Jessie Harkins was one of the larger gasoline-engined vessels to operate on the Columbia River. Jessie Harkins was built for the Harkins Transportation Company.

<i>Joseph Kellogg</i> (sternwheeler)

Joseph Kellogg was a stern-wheel driven steamboat that operated on the Willamette, Columbia, and Cowlitz rivers for the Kellogg Transportation Company. It was named after the company's founder, Joseph Kellogg (1812-1903). The sternwheeler Joseph Kellogg was built in 1881 at Portland, Oregon.

<i>Chester</i> (sternwheeler)

Chester was a shallow draft steamboat built in 1897 that ran until 1917, mostly on the Cowlitz River in southwestern Washington.

<i>Clara Parker</i> (sternwheeler)

Clara Parker was a sternwheel-driven steamboat which was operated on the lower Columbia and lower Willamette rivers in the 1880s. The steamer ran for about ten years out of Astoria, Oregon in towing and jobbing work. In 1890 Clara Parker was rebuilt and renamed Astorian.

<i>Relief</i> (1906 sternwheeler)

Relief was a stern-wheel steamboat that operated on the Columbia and Willamette rivers and their tributaries from 1906 to 1931. Relief had been originally built in 1902, on the Columbia at Blalock, Oregon, in Gilliam County, and launched and operated as Columbia, a much smaller vessel. Relief was used primarily as a freight carrier, first for about ten years in the Inland Empire region of Oregon and Washington, hauling wheat and fruit, and after that was operated on the lower Columbia river.

<i>N.S. Bentley</i>

N.S. Bentley, commonly referred to as simply Bentley, was a stern-wheel driven steamboat that operated on the Willamette rivers. Launched in East Portland in December 1886, Bentley ran until 1896, when it was rebuilt and renamed Albany. Bentley was owned by the Oregon Pacific Railway, and was used as part of a rail and marine link from Portland to San Francisco, running down the Willamette, then to Yaquina Bay, and then by ocean steamer south to California. In 1896, Bentley was rebuilt and renamed Albany.

<i>Undine</i> (Columbia River sternwheeler) American passenger steamboat

Undine was a sternwheel-driven steamboat that operated from 1887 to 1935 on the Columbia and lower Willamette rivers. From 1935 to 1940 the same vessel was operated under the name The Dalles.

<i>Mountain Gem</i> (sternwheeler)

Mountain Gem was a sternwheel-driven steamboat that operated on the Snake and Columbia rivers from 1904 to 1912, when the machinery was removed and installed in a different, newly built steamboat. Mountain Gem remained on the U.S. merchant vessel registry until 1922 or later. Although Mountain Gem was not abandoned until 1924, there is no evidence it was used after 1912.

<i>Ilwaco</i> (steamship)

Ilwaco was a small riverine and coastal steamship built in 1890 which was operated as a passenger vessel for the Ilwaco Railway and Navigation Company, and later served in other roles, including tow and freight boat, cannery tender and fish packing vessel. Ilwaco was originally named Suomi.

Callendar Navigation Company

The Callendar Navigation Company, sometimes seen as the Callendar Transportation Company, started in business in the early 1900s. Callendar was formed in the early 1900s, and was based in Astoria, Oregon. Callender was to become one of six large towing companies of the Columbia and Willamette rivers in the early decades of the 1900s, the others being Shaver Transportation, Smith Transportation, Hosford, Knappton Towing Co., and Willamette and Columbia River Towing Co. In 1922, Callendar Navigation merged with Knappton Towboat Co., which existed, with a name change in 1990, and which became part of Foss Marine in 1993.

References

Printed sources

On-line newspapers and journals

Images

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.