The Ford Motor Company produced straight-six engines from 1906 until 1908 and from 1941 until 2016. In 1906, the first Ford straight-six was introduced in the Model K. The next was introduced in the 1941 Ford. Ford continued producing straight-six engines for use in its North American vehicles until 1996, when they were discontinued in favor of more compact V6 designs.
Ford Australia also manufactured straight-six engines in Australia for the Falcon and Territory models until 2016, when both vehicle lines were discontinued. Following the closure of the Australian engine plant, Ford no longer produces a straight-six gasoline engine.
First generation
The H series flathead six cylinder engine.
The first-generation Ford six-cylinder engines were all flatheads. They were the G- and H-series engines of 226cuin (3.7L) used in cars and trucks and the M-series of 254cuin (4.2L) used in larger Ford trucks and for industrial applications.
226
Introduced for the 1941 model year, the first Ford L-6 (designated G-series) displaced 226cuin (3.7L) and produced 90hp (67kW), the same as the Flathead V-8 that year. Like the V-8, it was also a flathead or L-head engine. In 1948, Ford raised the compression of the flathead six or L-6 (designated H-series or Rouge 226) so that it generated 95hp (71kW) and 180lb⋅ft (244N⋅m) of torque. The G- and H-series engines were used in the full-sized Ford cars and trucks to replace the smaller 136cuin (2.2L)Flathead V8 that was used in the 1937 Ford. Ford discontinued production of the H-series engine for the 1951 model year.
254
A 254cuin (4.2L) version of the L-6 (designated the M-series or Rouge 254) was used from 1950 to 1953 in F6-series Ford trucks (COE, dump, truck-tractor, etc.), and small Ford school buses. The M-series engine produced 115hp (86kW) and 212lb⋅ft (287N⋅m) of torque. They were also used in miscellaneous industrial applications, e.g., to power water pumps for irrigation purposes and within vineyards to manage risk by powering giant frost-control propellers on stands in the middle of rows of grapes.
The second generation was a newly designed inline-six, produced from 1952 through 1964; it shared many parts with Ford Y-blocks such as the entire valve train and the problems associated with the Y-block's lubrication system. These engines have the exhaust and intake on the driver's side and the distributor on the passenger side. It is referred to as Mileage Maker or I-Block Mileage Maker (with the "I" referring to "inline") in the passenger cars and Cost Clipper in the trucks.
215
A completely new OHV I-6 was offered for the 1952–53 F-Series. It displaced 215cuin (3.5L) and produced 101hp (75kW). It was also used in the 1952–53 Ford full-sized cars.
223
The 215 grew to 223cuin (3.7L) for the 1954 F-Series. Output was now 115hp (86kW) in the trucks and 120hp (89kW) in the 1954 Ford cars. Power was up to 137hp (102kW) in the 1956 trucks. While not the popular engine option, the 223 was the only inline-six offered in the Fairlane (until 1961), Galaxie, and F-Series trucks between 1955 and 1964, causing it to be not quite a rarity, but not easy to come across. The 223 was also used in 1963–1964 Ford trucks, which also used the Autolite 1100 carburetor with stamping C4TF-E and produced 145hp (108kW) with 206ft-lb of torque, and Mercury Meteor-Monterey in 1961. The 223 was also used in Onan 30EC generator sets and possibly others.[1]
262
A 262cuin (4.3L) I-6 version was also produced. The 262 I-6 was built from 1961 to 1964 for use in medium- and heavy-duty Ford trucks. This engine was also used for industrial applications.
Third generation
The third generation was produced at the Lima Engine plant in Lima, Ohio, from 1960 through 1984. Officially dubbed the Thriftpower Six, this engine line is sometimes referred to as the Falcon Six.
The 144cuin (2.4L) inline-six engine was first introduced in the 1960 Ford Falcon. The 144 was made from 1960 through 1964 and averaged 90hp (67kW) during the production run. While not known for being powerful or a stout engine, it proved to be economical and could get fairly good gas mileage for the time, up to 30mpg‑US (8L/100km). This small six was the basis for all the Ford "Falcon" straight-six engines. The intake manifold on this series was cast integrally with the cylinder head (this design was also used by Chevrolet with some of their later third-generation inline-sixes, the older engines had separate manifolds); as a result, they could not be easily modified for greater power. This engine had four main bearings and can be identified by the three core plugs on the side of the block.
In 1961, the 170cuin (2.8L) became an option for the Falcon and Comet lines. The 170 Special Six was a stroked version of the 144, increasing the stroke from 2.5 to 2.94in (63.5 to 74.7mm). The original 1965 Ford Mustang used a 101hp (75kW) version from March (production start) through July 1964. The Econoline van and Ford Bronco received a heavier-duty version with mechanical valve lifters. This engine had four main bearings and can be identified by the three core plugs on the side of the block. The 170 Special was dropped from production in 1972.
As used in the Argentinian-made Ford Falcon from 1962 until 1970, this engine produced 96hp (72kW) at 4400rpm.
187
From 1965 to 1969, Ford Argentina produced a specific 186.7cuin (3.1L; 3,060cc) block similar to the earlier 200cuin (3.3L), with four main bearings and a 3.126in (79.4mm) stroke) but with a 3.56in (90.4mm) bore. It was replaced by the 188cuin (3.1L) from 1969. Power was rated at 116hp (87kW).
200
The 200.0cuin (3.3L; 3,278cc) inline-six model was introduced in the middle of 1963 with 3.685 by 3.126in (93.6 by 79.4mm) bore and stroke, and shared the four main bearing design of the 170. Early 200s can be identified by three core plugs. Beginning in 1965, the 200s were upgraded to seven main bearings to reduce harmonic vibrations and increase durability. The 1965 and later engines can be identified by four core plugs and the casting code C5DE-H. The 1965 Mustang (August 1964 onward) used this engine as standard, rated at 120hp (89kW). The Mustang continued to use the 200 as its base engine until it was dropped in 1971. Starting in 1966, a six-bolt bellhousing flange block was introduced. Beginning in 1980, one version of the 200 block was redesigned with a bell housing flange and a low-mount starter very similar to the low-mount starter 250 inline-six. This version is easily identified by starter location down by the oil pan rail and is referred to as the Big Bell 200. The big bell design is uncommon, but sought after by I-6 performance enthusiasts because it can be modified to accept a Ford small block V8 six bolt bell housing. There were concurrent high-mount starter 200 blocks made till 1983 model year, and they are more common than low-mount starter 200s.
When Ford launched the third-generation Fox body Mustang in 1979, the original engine lineup included the Cologne V6. The same engine was also offered in the hugely successful Ford of Europe Capri Mk II. The 2.8L V6 engine was a popular option for the US Mustang and the European Capri Mk II, and as a result, the Cologne engine plant could not meet the demand for engines for both continents. As a result, the Cologne 2.8L V6 was dropped from the Mustang's engine lineup in the middle of the 1979 production year and replaced with the 200 Falcon inline-six, which was then referred to as the 3.3L engine. The engine and front suspension K-member were transferred from the Fairmont, which helped reduce costs instead of having to redesign the Mustang for a different engine.
The 200 was used in the Ford Maverick and Mercury Comet and continued in the Ford Fairmont and Mercury Zephyr until they were discontinued at the end of the 1983 model year. The 1975–80 Ford Granada and Mercury Monarch offered the 200 inline-six as the standard engine. For 1981–82 the Ford Granada was redesigned and common with an expanded line of Mercury Cougars which used the 200 inline-six as the standard engine. From mid-year 1980 through 1982 the Ford Thunderbird and Mercury Cougar XR-7 used the 200 inline-six as the standard engine. The Ford LTD and Mercury Marquis, introduced in 1983 as the successors to the Granada and Cougar (non-XR7 models), carried over the 200 engine until it was replaced by the 3.8L Essex V6 for 1984.
Ford was also having problems meeting demand for its 2.3L OHC engine, which was used in a multitude of models worldwide. In anticipation of another engine shortage, the Ford engine plant in Lima, Ohio, which was already producing the 2.3-liter OHC engine, decided they could modify the Falcon inline six block casting molds to remove cylinders 4 and 5 to create a four-cylinder engine. A cast-iron high-swirl cylinder head was developed, and the new 2.3L engine was designated the HSC to differentiate it from the same displacement 2.3L OHC design. This engine shared many common parts with the 200, and it is common for persons rebuilding their 200 engines to use the 2.3L HSC pistons as a cheap replacement.[citation needed]
The 250cuin (4.1L) inline-six engine was offered in 1969 in the Mustang, and 1970 in compact Ford cars (Maverick). The 250 was a stroked 200, made by increasing the stroke from 3.126 to 3.91in (79.4 to 99.3mm). Output was 155hp (116kW) in the Mustang, and the 250 became the base engine in 1971. The Ford Granada and Mercury Monarch offered the 250 inline-six for the 1975–1980 model years, when it was replaced by the 200 inline-six.
Power was re-evaluated at 98hp (73kW) for 1972 (because of power rating changes) and 88hp (66kW) the next year. This engine had seven main bearings, and can be identified by the five core plugs on the side of the block. The block uses a low-mount starter and six bellhousing bolts, sharing its bellhousing pattern with the 302 and 351 Windsor V8s, late (1965–68) 289, early 4.6L V8, and the 240 and 300 inline-six. Production of the 250 ended in 1980.
Produced at the Cleveland Engine plant in Brook Park, Ohio, from 1964 through 1996, the 240 and 300 inline-six engines are well known for their durability. These engines employed seven main bearings and used long-wearing timing gears instead of a chain or belt.
Both the 240 and the 300, no matter the application, used a single-barrel Autolite 1100/1101 (or Carter YF/A) carburetor until the introduction of electronic fuel injection in 1987. With proper gearing, many F-Series trucks and Broncos achieve 20mpg‑US (12l/100km). This fact was heavily used by Ford's advertising campaign (some television advertisements and written literature even claimed 30mpg‑US (8l/100km)), since the V8 engines in these trucks rarely achieved over 14mpg‑US (17L/100km).
The fuel economy of the 300 makes the engine a popular choice among truck enthusiasts that want both power and economy. The addition of performance parts (such as intake and exhaust manifolds with a four-barrel carburetor) place the engine power output near the same levels as the stock "HO" (High Output) version of the optional 351 V8, with little or no change in economy.[citation needed]
240
The 240cuin (3.9L) inline-six for 1965–1972 full-sized cars (continued to 1974 in fleet models) and 1965–1974 trucks and vans produced 150hp (112kW) (gross). In stationary service (generators and pumps) fueled by LPG or natural gas, this engine is known as the CSG-639. The 240 had a bore of 4in (102mm) and a stroke of 3.18in (81mm).
300
Ford 300 irrigation pump. This one is equipped with extra cooling devices due to the radiators on these units being inadequate to cool the engine in very hot weather
The 300cuin (4,918cc) six was first offered in the F-Series for 1965. It is essentially a 240cuin (3.9L) with a longer stroke of 3.98in (101mm). The two engines are nearly identical; the differences are in the rotating assembly and combustion chamber sizes in the head (the heads are interchangeable). It produced 170hp (127kW) (gross). The 300 became the base F-Series engine in 1978 at 114hp (85kW) (horsepower number changes due to Ford switching to net power ratings in 1971). Power outputs were increased to roughly 122hp (91kW) during the early 1980s, before fuel injection was introduced. This became the primary engine of the line, eclipsing the 240. Unlike the Falcon engine, it featured separate intake and exhaust manifolds, which could be easily replaced with aftermarket manifolds offering the promise of even more power, through the installation of larger carburetors and a higher flowing exhaust system.
Also during the late 1960s and early 1970s, the 300 was used in larger vehicles such as dump trucks, many weighing into the 15,000lb (6,804kg) to 20,000lb (9,072kg) range. These engines were equipped with a higher flow HD (Heavy Duty) exhaust manifold and forged crankshafts and rods, as the engines would be constantly working in the 3,000–4,000rpm range. Due to their high-flowing design, enthusiasts often seek these manifolds out because they allow turbochargers to be easily retrofitted to the engine.[citation needed]
Beginning in 1978, the engine displacement was advertised in metric, becoming "4.9L." Fuel injection and other changes in 1987 increased output to 150 horsepower (112kW) with an 8.8:1 compression ratio. Even though this engine was renowned for its durability, low-end torque, and ease of service, it was gradually phased out. Production ended in 1996, making it the last inline-six gasoline engine offered in a Ford car or light truck in North America. It was replaced by the 4.2L Essex V6 for 1997 in the redesigned F-150, as well as the E-150 and E-250.
The 300 was mated to the Ford C6, E4OD, and AOD automatic transmissions, and the Mazda M5OD, ZF S5-42 and S5-47, 5-speed manual transmissions, and the Borg-Warner T18, Tremec RTS, and New Process NP435 4-speed manual transmissions.
Race car driver Scott Donohue raced a rally truck with a Ford 300 inline-six in it and won the Baja 1000 three times. This engine is also used by Stewart & Stevenson in the MA Baggage Tow Tractor,[2] and Harlan in their standard tow tractors,[3] as well as a multitude of other pieces of equipment, such as ski lifts, power generators, wood chippers, tractors, and, until they converted to diesel engines, most UPS trucks. In stationary service (generators and pumps) fueled with LPG or natural gas, this engine is known as the CSG-649.
Applications:
1965–1996 Ford F-Series (F-100, F-150, F-250, F-350, and F-600)[4]
The Australian Ford straight-six as seen in an XD series Ford Falcon, following adoption of a crossflow design in 1976, and an alloy cylinder head in 1980.
With local production of the Ford Falcon starting in 1960, Ford Australia began to offer the same inline-six engines as offered in North America. In Australia, the engine underwent significant updates to its design over the following decades, including a move to a crossflow layout, electronic ignition, alloy cylinder heads, fuel injection, overhead camshaft and later multi-valve double overhead camshaft design, variable intake runners, variable valve timing, and ultimately turbocharging. It remained in production for 56 years, retaining the same bore centres of the original 1960 Falcon engine throughout its evolution.[6]
144, 170, and 200, 3.1 and 3.6 litre
Initially, the 90hp (67kW) 144 and 101hp (75kW) 170 cu in 'Pursuit' engines were offered. The 121hp (90kW) 200 cu in 'Super Pursuit' engine option added in February 1964 with the introduction of the XM Falcon, at which time the 144 and 170 underwent changes to cylinder head, camshaft and exhaust design that increased their outputs to 96hp (72kW) and 111hp (83kW) respectively.[7] In 1965, all three engines received a revised camshaft for increased low-speed performance with the introduction of the XP Falcon.[8][9] The 144 remained in production until the late 1966 introduction of the larger, second generation XR Falcon.[10]
In 1968, coinciding with the release of the XT Falcon, the deck height of the design was increased to make room for increased crankshaft stroke, resulting in displacements of 188 and 221 cu in (badged 3.1 and 3.6 litres).[11] These engines featured a seven-bearing crankshaft and shared a common 3.68in (93.5mm) bore, with strokes of 2.94 or 3.46in (74.7 or 87.9mm) respectively.[12] They superseded the 170 and 200 engines in the Australian Falcon lineup. The 188 and 221 also powered the Argentine Falcon range from 1970 to 1991.
200 and 250
In 1970, in conjunction with the release of the XY Falcon, Ford Australia enlarged capacities to 200 and 250 cu in., reverting to imperial cubic inch measurements for identification. Bore and stroke dimensions for the Australian engines were identical to their US counterparts of the same capacities, but the structure of the engine was different; both Australian engines shared a common block with the crankshaft positioned lower in the block to accommodate the longer stroke of the 250, whereas the US 250 engines had increased deck height.[13] The head was of similar design to previous models, with an integral intake catering for a single-barrel Bendix-Stromberg carburettor. Outputs for the 200 and 250 cu in. engines were rated at 130hp (97kW) and 155hp (116kW) respectively.[14] From September 1972 both 200 and 250 cu in variants also became available on locally manufactured Ford Cortinas,[15] and by 1974 the 250 was now the standard engine for the locally-assembled Ford F series truck range.[16]
As a performance option for the XY Falcon and subsequent XA Falcon, Ford developed the 2V (two-venturi) variant of the 250 cu in. engine. The cylinder head, which in all respects was similar to the previous integral "log head" intake, with the exception of a removable aluminium intake which mounted a Bendix-Stromberg WW two-barrel carburettor. To take advantage of the much improved breathing ability that the removable intake brought to the new head, the 250-2V also featured a better-breathing exhaust manifold.[14] Output was rated at 170hp (127kW), and road tests noted a reduction in 0 to 60mph (97km/h) acceleration time from 14 to 10.7 seconds over a Falcon equipped with the standard single-barrel 250 cu in. engine.[17] For years, the 250-2V cylinder head was very popular for racing and many have been imported to North America, where owners of cars with the Falcon inline six have upgraded their engines with the higher-performance cylinder head.
Crossflow, Alloy Head, Alloy Head II and EFI
The cast iron crossflow head was introduced to the Ford Australia straight-six in 1976. As well as the Falcon/Fairmont range, the engine was also fitted to locally-built variants of the Ford Cortina, as seen here.
From 1 July 1976, new emission standards came into effect with Australian Design Rule 27A, which set limits for the emissions of hydrocarbons, carbon monoxide, and oxides of nitrogen.[18] To meet the new requirements, compression ratios were dropped, and the engines now featured an exhaust gas recirculation valve and positive crankcase ventilation. In an effort to maintain horsepower outputs, Ford Australia updated the engines with a new cast-iron crossflow head design with larger, canted valves, and an aluminium water-heated intake manifold to improve gas flow and warm-up. Only the block, crankshaft, pistons and conrods were carried over from the old engine.[19] Whereas the previous integral "log head" engine borrowed from the Ford FE engine family design, the new crossflow engine borrowed from the Ford Cleveland engine family. Introduced with the XC Falcon, engine displacements remained 200 and 250 cu in, but were now badged 3.3 and 4.1 litres, respectively, and power and torque outputs were expressed in metric units. While quoted power outputs dropped from 130 to 107 horsepower (97 to 80kW) for the 3.3, and from 155 to 123 horsepower (116 to 92kW) for the 4.1, power was now measured using the DIN rather than SAE gross method. Ford claimed the new crossflow engines had a performance gain of approximately ten per cent over their reverse-flowXB Falcon predecessors,[20][19] which were rated at 95 horsepower (71kW) and 111 horsepower (83kW) respectively when tested to the same DIN method.
With the introduction of the 1979 XD Falcon, changes to compression ratio, ignition advance and revisions to port design for improved gas flow saw modest increases to power and torque outputs.[21] In June 1980, Ford Australia updated the crossflow design with a new aluminium head casting developed in conjunction with Honda, and introduced electronic ignition.[22] Dubbed Alloy Head and introduced as part of a mid-life update of the XD Falcon, the revised engines featured a high-swirl, lean-burn combustion chamber design that enabled higher compression ratios to be used while still meeting emissions requirements.[23] The use of aluminium alloy meant that the engines were 22.4 kilograms (49lb) lighter, and had improved warm-up time. Power outputs for the 3.3 and 4.1 litre engines now raised to 84kW (113hp) and 94kW (126hp) respectively, with reductions in fuel consumption of seven to ten per cent.[24] Until 1982, the engines were fitted with a single-barrel Bendix-Stromberg carburettor, but with the introduction of the XE Falcon from March 1982, both 3.3 and 4.1 litre engines were fitted with a Weber two-stage carburettor. It featured two venturi, with the second venturi coming into operation only when the first venturi opening exceeded two-thirds.[25] Power outputs for the new engines, designated Alloy Head II, increased to 90kW (120hp) and 105kW (141hp) respectively,[26][27] and fuel economy improved over that of the previous Alloy Head engines with single-barrel carburettor.
In March 1983, direct-port fuel injection using BoschJetronic LE was offered as an option on the 4.1L engine.[28] With the release of the XF Falcon the following year, the injected 4.1 was upgraded with Ford's EEC-IV engine management system with Multi Point Electronic Fuel Injection (MP-EFI). Changes to the carburettor-based engine were made to accommodate the EFI system. The cylinder head intake ports had been modified to provide clearance for the injectors, and a new intake manifold was designed and many other changes were made in the engine bay to accommodate the new fuel system.
In response to Australian Design Rule 37, which required all new cars sold after 1 January 1986 to operate with unleaded petrol,[29] Falcon engines were modified for running on regular grade 91 RON unleaded fuel and equipped with catalytic converters. Despite revisions that included a higher-lift camshaft and revised combustion chamber shape,[30] power and torque outputs for the carburetted 3.3 and 4.1 litre engines fell to 88kW (118hp) and 97.5kW (130.7hp), although maximum power output from the 4.1 EFI engine increased slightly to 121kW (162hp).[31] While the OHV six-cylinder engines were replaced by OHC variants across the Ford Australia passenger car range in 1988, the carburetted 4.1 litre engine remained in production until 1993 along with the ute and panel van variants of the XF Falcon for which it was the only engine offered.[32]
OHC and Intech
The straight six as seen in the performance-oriented 1994-1996 EF series Ford Falcon XR6. By this time, it had evolved from an OHV to a SOHC design, featuring multipoint fuel injection and a dual-resonance intake manifold.
In 1988, the inline six engines underwent a major redesign for the EA26 Falcon and now featured a new single overhead cam (SOHC) crossflow aluminium head. Two engine sizes were offered, based on a common 91.86mm (3.617in) cylinder bore. The smaller engine, dubbed 3.2 litre, featured a 79.30mm (3.122in) stroke and a swept volume of 3,157 cubic centimetres (193cuin). The larger engine, dubbed 3.9 litre, shared the 99.31mm (3.910in) stroke of the previous 4.1 litre engine for a swept volume of 3,949 cubic centimetres (241cuin). Electronic fuel injection was now used across with range, with the 90kW (121hp) 3.2 litre engine equipped with throttle body injection, and the 3.9 litre engine available with a choice of 120kW (161hp) throttle body injected or 139kW (186hp) multipoint fuel injected variants.[33]
The updated design featured camshaft and auxiliary shafts driven by a duplex chain, and chain rive to the distributor and the oil pump shafts. The camshaft was supported on the cylinder head by using 'topless' bearings; bearing liners were not used. The camshaft was held in position using valve spring pressure, with hydraulic lash adjusters mounted on the rocker arms were used to provide zero valve lash.
By late 1988, the 90kW (121hp) 3.2 litre engine was no longer competitive against the 125kW (168hp) base engine option offered in the newly-released Holden Commodore and was discontinued by the end of that year, leaving the two 3.9 litre engines as the only choices.[33] In 1992, in conjunction with a mid-life update of the EB Falcon, the cylinder bore was increased to 92.25 millimetres (3.632in), increasing swept volume to 3,984 cubic centimetres (243cuin). Dubbed 4.0 litre and now available only with multipoint fuel injection, the engine was rated at 148kW (198hp).[34]
During 1992, a high output variant of the 4.0 litre engine, featuring a modified cylinder head and camshaft developed by Tickford Vehicle Engineering, was introduced.[35] Fitted to the sports-oriented Falcon S-XR6 (renamed Falcon XR6 with the updated ED Falcon in 1993) it developed 161kW (216hp), only 4kW (5hp) less than the optional 5.0 litre V8 also offered with the EB and ED Falcon.[36]
In conjunction with the release of the EF Falcon range in 1994, Ford introduced a dual resonance intake manifold aimed at providing greater low-speed torque, branding the system Computer Torque Control. While the torque peak of the standard engine increased by only 9N⋅m (7lbf⋅ft) to 357N⋅m (263lbf⋅ft), Ford claimed that mid-range torque was now as much as 28N⋅m (21lbf⋅ft) higher.[37] Power increased to 157kW (211hp) for the standard engine, and 164kW (220hp) for the high-output XR6 variant. The engine management system was upgraded to Ford's EEC V, and the distributor was replaced by a three-coil ignition system with each coil firing two spark plugs.[38] However, the subsequent EL Falcon reverted to a distributor/coil ignition setup.
Ford Australia redesigned the I-6 again, naming it the Intech, in 1998 alongside the introduction of the Ford Falcon (AU), and increased the main bearing size and added a ladder style main stud girdle integral with the oil pan to increase low end rigidity. The engine also received variable camshaft timing technology in some XR6 models, Fairlane/LTD models and the Fairmont Ghia which allowed the ECU to advance or retard camshaft timing depending on engine speed, which results in a broader power band. The Composite Headgasket from the previous models was replaced with a Multi-Layer-Steel (MLS) gasket. Power outputs for the base model Falcon Forte, Fairmont, and the standard XR6 were unchanged from their EL series predecessors, but a new 172kW (231hp) XR6 VCT model was offered. The Fairmont Ghia, Fairlane and LTD models were also equipped with a 168kW (225hp) variant of the VCT engine.
Barra
The 245kW (329hp) turbocharged variant of the DOHC 24-valve six. The Barra engines all featured variable cam timing on both camshafts.
In 2002, the engine underwent a significant upgrade receiving dual overhead cams (DOHC) with variable cam timing and coil-on-plug ignition. The engine gained the nickname "Barra", named after the "Barramundi" code name used during the development of the Ford Falcon (BA), and a numerical suffix was used to identify the engine variant by its output in kilowatts. Producing 182kW (244hp) and 380N⋅m (280lb⋅ft) in Barra 182 form, it debuted in the Ford Falcon (BA) of 2002 and also powered the Ford Territory introduced in 2004. In October 2005, alongside the introduction of the Ford Falcon (BF) and Ford Territory (SY), these outputs rose to 190kW (250hp) and 383N⋅m (282lb⋅ft). In 2008 the Barra was upgraded a final time, debuting in the Ford Falcon (FG) with power outputs of 195kW (261hp) and 391N⋅m (288lb⋅ft).
Turbocharged versions were also manufactured. The initial version, known as Barra 240T with 240kW (322hp) and 450N⋅m (330lb⋅ft) of torque was offered between 2002 and 2005 in the BA Falcon XR6 Turbo, as well as the Territory Turbo. This was followed in the BF and BF Mk II XR6 Turbo (between 2005 and 2008) by the Barra 245T producing 245kW (329hp) of power and 480N⋅m (350lb⋅ft) of torque, which in turn was followed by the Barra 270T from 2008-2016 in the FG and FG X XR6 Turbo and G6E Turbo models producing 270kW (362hp) of power and 533N⋅m (393lb⋅ft) of torque.
Ford Australia's high-performance division, Ford Performance Vehicles (FPV), created even more powerful turbocharged variants. The first turbocharged straight six-engined car from FPV was the BA Mk II F6 Typhoon (2004), which produced 270kW (362hp) of power and 550N⋅m (410lb⋅ft) of torque. The first power and torque upgrade came with the FG range of 2008, which saw outputs rise to 310kW (416hp) of power at 5500rpm and 565N⋅m (417lb⋅ft) of torque. This engine, the Barra 310T, was the first Australian-built engine to achieve over 100hp (75kW) per litre.[39]
The ultimate iteration of the Barra engine was installed in the limited-production FG X XR6 Sprint (limited to 500 units) of 2016. This engine produced 325kW (436hp) at 6000rpm and 576N⋅m (425lb⋅ft) at 2750rpm. The engine features an overboost function that can increase output to 370kW (496hp) and 650N⋅m (480lb⋅ft) for up to ten seconds.[40]
Ford Australia had intended to discontinue production of the straight six engine at their engine plant in Geelong in 2010 and replace it in the Falcon and Territory models with an imported V6 engine, although later reversed this decision in favour of upgrading the Barra to meet then-upcoming Euro IV emissions standards.[41][42] This would prove to be only a temporary stay of execution as the Geelong factory eventually closed on 26 September 2016, following Ford's decision in May 2013 to discontinue the Falcon and Territory and cease manufacture of vehicles in Australia.[43] The last Australian-built Ford, and the last Ford passenger vehicle to be fitted with a straight-six engine, rolled off the production line at the Broadmeadows Assembly Plant on 7 October 2016. It was a Kinetic Blue FG X Falcon XR6 sedan, equipped with the naturally-aspirated Barra 195 straight six engine.[44]
Ford Falcon (Australia) straight-six engine specifications
370kW (496hp) and 650N⋅m (479lb⋅ft) with overboost function.
FPV F6 model
Capacity
Induction
Valvetrain
Fuel
Power
Torque
Notes
BA MkII, BF
4.0L
EFI
DOHC
Unleaded
270kW (362hp)
550N⋅m (406lb⋅ft)
FG
4.0L
EFI
DOHC
Unleaded
310kW (416hp)
565N⋅m (417lb⋅ft)
Related Research Articles
The straight-six engine is a piston engine with six cylinders arranged in a straight line along the crankshaft. A straight-six engine has perfect primary and secondary engine balance, resulting in fewer vibrations than other designs of six or fewer cylinders.
The Ford Falcon is a full-size car that was manufactured by Ford Australia from 1960 to 2016. From the XA series of 1972 onward, each Falcon and range of derivates have been designed, developed, and built in Australia, following the phasing out of the American-influenced Falcon of 1960 to 1971, which had been re-engineered locally as the XK to XY series for the harsher Australian conditions. The luxury-oriented Ford Fairmont model joined the range from 1965. Luxury long-wheelbase derivative versions called the Ford Fairlane and LTD arrived in 1967 and 1973 respectively with production ending in 2007.
The Ford small-block is a series of 90° overhead valve small-block V8 automobile engines manufactured by the Ford Motor Company from July 1961 to December 2000.
The Ford Pinto engine was the unofficial name for a four-cylinder internal combustion engine built by Ford Europe. In Ford sales literature, it was referred to as the EAO or OHC engine and because it was designed to the metric system, it was sometimes called the "metric engine". The internal Ford codename for the unit was the T88-series engine. European Ford service literature refers to it as the Taunus In-Line engine. In North America it was known as the Lima In-Line (LL), or simply the Lima engine due to its being manufactured at Lima Engine in Lima, Ohio.
The Ford Modular engine is Ford Motor Company's overhead camshaft (OHC) V8 and V10 gasoline-powered small block engine family. Introduced in 1990, the engine family received its “modular” designation by Ford for its new approach to the setup of tooling and casting stations in the Windsor and Romeo engine manufacturing plants.
The Ford Cologne V6 is a series of 60° cast iron block V6 engines produced by the Ford Motor Company from 1962 to 2011 in displacements between 1.8 L; 110.6 cu in (1,812 cc) and 4.0 L; 244.6 cu in (4,009 cc). Originally, the Cologne V6 was installed in vehicles intended for Germany and Continental Europe, while the unrelated British Essex V6 was used in cars for the British market. Later, the Cologne V6 largely replaced the Essex V6 for British-market vehicles. These engines were also used in the United States, especially in compact trucks.
The Essex V6 is a 90° V6 engine family built by the Ford Motor Company at the Essex Engine Plant in Windsor, Ontario, Canada. This engine is unrelated to Ford's British Essex V6. Introduced in 1982, versions of the Essex V6 engine family were used in subcompact through to large cars, vans, minivans, and some pickup trucks. The Essex V6 was last used in the 2008 regular-cab F-150, after which it was succeeded by a version of the Ford Cyclone engine. An industrial version of the engine was available until 2015.
The Ford HSC engine is an automobile gasoline engine from the Ford Motor Company, sold from 1984 until 1994. HSC stands for High Swirl Combustion. It was made in two displacements: 2.3 L and 2.5 L, and used in only two model lines: the Ford Tempo/Mercury Topaz and the Ford Taurus/Mercury Sable.
The Ford flathead V8 is a V8 engine with a flat cylinder head introduced by the Ford Motor Company in 1932 and built by Ford through 1953. During the engine's first decade of production, when overhead-valve engines were used by only a small minority of makes, it was usually known simply as the Ford V‑8, and the first car model in which it was installed, the Model 18, was often called simply the "Ford V-8" after its new engine. An automotive milestone as the first affordable V8, it ranks as one of the company's most important developments. The engine was intended to be used for big passenger cars and trucks; it was installed in such until 1953, making the engine's 21-year production run for the U.S. consumer market longer than the 19-year run of the Ford Model T engine. It was also built independently by Ford licensees.. The engine was named on Ward's list of the 10 best engines of the 20th century. It was a staple of hot rodders in the 1950s, and it remains famous in the classic car hobbies even today, despite the huge variety of other popular V8s that followed.
Ford Performance Vehicles was the Melbourne-based, premium performance arm of automobile manufacturer Ford Australia. The company produced a range of Ford-based models from 2002 to 2014 under the FPV marque name.
Barra is a name for an engine range created by Ford Australia, including the inline-6 and unrelated SOHC V8 in the Ford Australia Falcon between 2002 and 2016. The inline-6 engines are unique to the Australian manufactured Falcon and Territory and were developed and manufactured in Geelong, Victoria. The Barra was first introduced in the BA Falcon, named after the "Barramundi" code name used during the development of the BA update engine. The V8 engine, from Windsor, Ontario, were discontinued with the FG model whereas the I6 engines continued production until 26 September 2016, coinciding with the end of production of the Falcon and Territory on 7 October.
The Ford Falcon (BA) is a full-sized car produced by Ford Australia from 2002 to 2005. It was the second significantly re-engineered iteration of the sixth generation of the Falcon, and also included the Ford Fairmont (BA)—the luxury-oriented version. This platform also formed the basis of the Ford Territory sport utility vehicle.
The Ford Falcon (AU) is a full-size car that was produced by Ford Australia from 1998 to 2002. It was the sixth generation Ford Falcon and also included the Ford Fairmont (AU)—the luxury-oriented model range. The AU series replaced the EL Falcon and was constructed on the (at the time) new EA169 platform which continued to harbour Falcon models until 2010 when the BF wagon was discontinued, and Ford Territory models until 2011. The AU series was replaced by the updated BA series.
The Ford Falcon (EL) is a full-size car that was produced by Ford Australia from 1996 to 1998. It was the fifth and final iteration of the fifth generation of the Falcon and also included the Ford Fairmont (EL)—the luxury-oriented version.
The Ford Falcon (EF) was a full-size car that was produced by Ford Australia from 1994 to 1996. It was the fourth significantly updated iteration of the fifth generation of the Falcon and also included the luxury-oriented Ford Fairmont (EF).
The Ford Falcon (FG) is a full-sized car that was produced by Ford Australia from 2008 to 2014. It was the first iteration of the seventh and last generation of the Falcon. Its range no longer featured the Fairmont luxury badge, replaced instead by the G Series.
The Ford Falcon (XE) is a full-size car that was produced by Ford Australia from 1982 until 1984. It was the second iteration of the fourth generation of the Falcon and also included the Ford Fairmont (XE)—the luxury-oriented version.
The Ford Falcon (XF) is a full-sized car that was produced by Ford Australia from 1984 to 1988. It was the third iteration of the fourth generation of the Falcon and also included the Ford Fairmont (XF)—the luxury-oriented version. Between 1993 and 1999, this series provided the platform for the Falcon utility (XG and XH) that was sold alongside the fifth-generation Ford Falcon sedans and wagons.
Tickford Vehicle Engineering (TVE) was a company responsible for numerous automotive projects and upgrades for Ford Australia between 1991 and 2002. In 1999, TVE setup Ford Tickford Experience (FTE) as a competitor to Holden Special Vehicles (HSV). In 2002, the operations changed to Ford Performance Vehicles (FPV), coinciding with Tickford's global operations being bought out by Prodrive.
The Ford Falcon (FG X) is a full-size car that was produced by Ford Australia. Introduced in 2014, it is a restyled second and final iteration of the seventh generation Falcon FG. While external and drive train changes were significant, the interior was carried over from the 2008-2014 FG model. This was the last locally produced model by Ford Australia.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
