The M1917 Enfield, the "American Enfield", formally named "United States Rifle, cal .30, Model of 1917" is an American modification and production of the .303-inch (7.7 mm)Pattern 1914 Enfield (P14) rifle (listed in British Service as Rifle No. 3), which was developed and manufactured during the period 1917–1918. Numerically, it was the main rifle used by the American Expeditionary Forces in Europe during World War I. The Danish Sirius Dog Sled Patrol in Greenland still use the M1917, which performs reliably in Arctic conditions, as their service weapon.
Before World War I, the British had the Short Magazine Lee–Enfield (SMLE) as their main rifle. Compared to the German Mausers or U.S. 1903 Springfield, the SMLE's .303 rimmed cartridge, originally a black powder cartridge, was ill-suited for feeding in magazine or belt-fed weapons and the SMLE was thought to be less accurate than its competition at longer ranges. The long-range accuracy of the German 7×57mmMauser Model 1895 in the hands of Boer marksmen during the Boer War (1899-1902) made an impression on the British Army, and a more powerful, modern rifle was desired. Thus, even though improved Lee–Enfield variants (the SMLE) and .303 British Mark VII ammunition with pointed (spitzer) projectiles entered service after the Boer War in 1910, a committee was formed to develop an entirely new design of rifle and cartridge. The starting point was to copy many of the features of the Mauser system. The rifle was developed at the Royal Small Arms Factory at Enfield (arsenal) in the United Kingdom.
This development named the Pattern 1913 Enfield or P13, included a front locking, dual lug bolt action with Mauser type claw extractor as well as a new, powerful rimless .276 Enfield cartridge. The design carried over a Lee–Enfield type safety at the rear of the action and a bolt that cocked on closing to ease unlocking of the bolt during rapid fire. An advanced design, for the era, of aperture rear sight and a long sight radius were incorporated to maximize accuracy potential. Ease of manufacture was also an important criterion. However, the onset of World War I came too quickly for the UK to put it into production before the new cartridge could be perfected, as it suffered from overheating in rapid fire and bore fouling.
As it entered World War I, the UK had an urgent need for rifles, and contracts for the new rifle were placed with arms companies in the United States. They decided to ask these companies to produce the new rifle design in the old .303 British chambering for convenience of ammunition logistics. The new rifle was termed the "Pattern 14". In the case of the P14 rifle, Winchester and Remington were selected. A third manufacturer, Eddystone Arsenal – a subsidiary of Remington – was tooled up at the Baldwin Locomotive Works in Eddystone, Pennsylvania. Thus, three variations of the P14 and M1917 exist, labeled "Winchester," "Remington" or "Eddystone".
World War I
When the U.S. entered the war, it had a similar need for rifles. The Springfield Armory had delivered approximately 843,000 M1903 Springfield rifles, but due to the difficulties in production, rather than re-tool the Pattern 14 factories to produce the standard U.S. rifle, the M1903 Springfield, it was realized that it would be much quicker to adapt the British design. Although it might have been faster to retain chambering for the .303 British military cartridge, the design was modified for the U.S. .30-06 Springfield cartridge to simplify ammunition logistics. The Enfield design was well suited to the .30-06 Springfield; it was a big, strong action and was originally intended to employ a long, powerful, rimless bottlenecked cartridge. Accordingly, Remington Arms Co. altered the design for caliber .30-06 Springfield, under the close supervision of the U.S. Army Ordnance Department, which was formally adopted as the U.S. Rifle, Caliber .30, Model of 1917. In addition to Remington's production at Ilion, New York and Eddystone, Pennsylvania, Winchester produced the rifle at their New Haven, Connecticut plant, a combined total more than twice the 1903's production, and was the unofficial service rifle. Eddystone made 1,181,908 rifles – more than the production of Remington (545,541 rifles) and Winchester (465,980 rifles) combined.[2][3] Although standardization with interchangeable parts was intended, early Winchester rifles (including the first five-thousand with a simple W on the receiver rather than Winchester) used slightly differing parts, causing interchangeability issues with the rifles produced by Remington and Eddystone until Winchester corrected the problem in later production.[4]
Design changes were few; the stripper clip feed, internal box magazine, bolt face, chamber and rifling dimensions were altered to suit the .30-06 Springfield cartridge and the US pattern 5-round stripper clips, the stock was slightly redesigned, lightening it somewhat, and the volley fire sights on the left side of the weapon were deleted. The markings were changed to reflect the model and caliber change. A 16.5-inch blade bayonet, the M1917 bayonet was produced for use on the rifle; it was later used on several other small arms including the M97 and M12trench shotguns.
The new rifle was used alongside the M1903 Springfield, and quickly surpassed the Springfield design in numbers produced and units issued. By November 11, 1918, about 75% of the AEF in France were armed with M1917s.[5]
An M1917 Enfield rifle was used by Sergeant Alvin C. York on October 8, 1918, during the event for which he was awarded the Medal of Honor, as the U.S. 82nd Division's (which York was a part of) official history states the division had been issued the M1917 (Eddystone), then replaced them with the No 1 Mk III Lee-Enfield while training with the British in the north of France, then were reissued M1917 rifles (Eddystone).[6] According to his diary, Sergeant York also used a Colt M1911 semi-automatic pistol on that day.[7][8] (The film Sergeant York starring Gary Cooper in the title role, had York using an M1903 Springfield and a German Luger pistol.)
After the armistice, most M1917 rifles were placed in storage, although Chemical Mortar units continued to be issued them. During the 1920s and 1930s, many M1917 rifles were released for civilian use through the NRA, or were sold as surplus. Many were "sporterized", sometimes including rechambering to more powerful magnum hunting cartridges, such as .300 H&H Magnum and .300 Winchester Magnum. It was so popular as a sporting weapon that Remington manufactured about 30,000 new rifles as the Model 30 from 1921 to 1940. In 1934, Honduras procured a version of the rifle chambered for 7×57mm known as Model 1934.[9]
World War II
At the time of the American entry into World War II, the U.S. Army was still issuing the M1917 to chemical mortarmen. Perhaps due to M1 Garand (or M1903A3) shortages at the start of the war, the M1917 was also issued to artillerymen, and both mortarmen and artillerymen carried the M1917 in North Africa. Lieutenant Colonel Charles E. Peterson (USAR, retired; 1920–2005), a Major in the 101st Airborne in the Normandy action, reported seeing some M1917 rifles issued to rear-echelon U.S. troops in France during World War II. Other M1917 rifles were issued to the Philippine Commonwealth Army and Philippine Constabulary.[10] After the fall of the Philippines, M1917 rifles were used by Japanese police forces[11] as well as by U.S. and Filipino soldiers with the local guerrillas before the liberation of the Philippines. These rifles were also used by the Hukbalahap.[12]
Before and during World War II, stored rifles were reconditioned for use as reserve, training and Lend-Lease weapons; these rifles are identified by having refinished metal (sandblasted and Parkerized) and sometimes replacement wood (often birch). Some of these rifles were reconditioned with new bolts manufactured by the United Shoe Machinery Company that were stamped “USMC,” leading to the mistaken impression these were United States Marine Corps rifles.[13] Many were bought by the United Kingdom through the British Purchasing Commission for use by the Home Guard; 615,000 arrived in Britain in the summer of 1940, followed by a further 119,000 in 1941.[14] These were prominently marked with a red paint stripe around the stock to avoid confusion with the earlier P14 that used the British .303 round. Others were supplied to the Nationalist Chinese forces, to indigenous forces in the China-Burma-India theater, to Filipino soldiers under the Philippine Army and Constabulary units and the local guerrilla forces and to the Free French Army, which can occasionally be seen in wartime photographs. The M1917 was also issued to the Local Defence Force of the Irish Army during World War II, these were part-time soldiers akin to the British Home Guard. In an ironic reversal of names, in Irish service the M1917 was often referred to as the "Springfield"; presumably since an "Enfield" rifle was assumed to be the standard Irish MkIII Short Magazine Lee–Enfield, while "Springfield" was known to be an American military arsenal.
As with all belligerents, Canada entered the Second World War short of small arms to equip its expanding military. 80,000 M1917s, designated “Rifle, Enfield .30/06,” were purchased in July 1940, along with 5,000,000 rounds of .30-06 ammunition. A further 20,000 were purchased in 1941. They were initially allotted to Canadian Army Basic and Advanced Training Centres, the Royal Military College of Canada and Canadian Army (Reserve) units. They would also be issued to the Veterans Guard of Canada, the Pacific Coast Militia Rangers and the Royal Canadian Air Force. The M1917 would fill a critical role in Canada's war effort, freeing .303-calibre weapons for front-line use or to be supplied to the UK after Dunkirk, when Canada provided 75,000 Ross Mark III rifles beginning on 22 May 1940.[15]
The M1917 was supplied to both Denmark and Norway after WWII as an interim weapon prior to the arrival of the M1 Garand.
Korean War and after
After World War II, the M1917 went out of front-line duty with the US forces. Chinese Communist forces used M1917 rifles during the Korean War.[16] This rifle was also used, unofficially, in small Middle-East and African conflicts as a military-assistance program supplied rifle.
Contemporary use
The M1917 is used as a ceremonial and drilling rifle, as with the M1903, M1 Garand, and M14. For military purposes, mainly as last resort against aggressive polar bears and muskoxen, the Danish Sirius Dog Sled Patrol (Slædepatruljen Sirius) still use the M1917, designated as Gevær M/53 (17) by the Danish, as their service weapon, due to the high reliability of these bolt-action rifles in the harsh conditions of high Arctic Greenland.[17]
Design details
M1917 Enfield breechM1917 Mauser M98 type boltM1917 ladder aperture sight
Due to the original P13 action being designed for a high-powered .276 Enfield round with a larger diameter case than the .30-06 Springfield, the magazine capacity for the smaller diameter .30-06 Springfield was six rounds, although stripper clips held only five cartridges.
Both P14 and M1917 rifles are noted for several design features. The rifle was designed with an iron sight line consisting of rear receiver aperture battle sight calibrated for 400yd (366m) with an additional ladder aperture sight that could be flipped up and was calibrated for 200–900yd (183–823m) in 100yd (91m) increments and 900–1,600yd (823–1,463m) in 50yd (46m) increments. The ladder aperture sight moves vertically on a slide, and hence was not able to correct for wind drift. The rear sight element was protected by sturdy "ears" and proved to be faster and more accurate than the typical mid-barrel sight offered by Mauser, Enfield or the Buffington battle sight of the M1903 Springfield. Future American rifles, such as the M1903A3 Springfield, M1 Garand and M1 carbine, would all use similar rear sights. The front sighting element consisted of a wing-protected front post, and was adjusted laterally and locked into position during assembly at the arsenal. The M1917 rear sight element was situated on an elongated receiver bridge, which added weight to the action, as well as lengthening the bolt. The M1917 has a 31.76in (806.7mm) sight radius. The battle sight radius is slightly shorter at 31.69in (804.9mm).[18] The M1917 action weighs 58oz (1,644g) versus 45oz (1,276g) for the M1903 Springfield.
The rifle maintains the British cock-on-closing feature, in which the bolt's mainspring is loaded and the rifle cocked as part of the return stroke of the bolt, which aided rapid fire, especially as the action heated up. Most bolt action designs after the Mauser 98 cocked as part of the opening stroke. The rifle has a characteristic "belly" due to a deeper magazine, allowing the rifle to hold six rounds of the US .30-06 cartridge in the magazine, and one in the chamber. The M1917 Enfield like the Mauser Gewehr 98 had no magazine cut-off mechanism, which when engaged permits the feeding and extraction of single cartridges only while keeping the cartridges in the magazine in reserve. In a manufacturing change from the Mauser 98 and the derivative Springfield, the bolt is not equipped with a third 'safety' lug. Instead, as on the earlier Model 1895 (Chilean) Mauser, the bolt handle recesses into a notch in the receiver, which serves as an emergency locking lug in the event of failure of the frontal locking lugs. This change saved machine time needed on the rifle bolt, cutting costs and improving production rates, and this alteration has since been adopted by many commercial bolt-action rifle designs for the same reasons. The unusual 'dog-leg' shaped bolt handle is low profile and places the bolt knob just rearwards of the trigger close to the firer's hand, facilitating rapid cycling and fire. Like the Lee–Enfield, P13 and P14, the safety falls under the firer's thumb and can be operated silently. The M1917 Enfield bolt locking lugs had a 4 degree helical angle with matching angles on the receiver lug seats (the technical term is interrupted threading). This means that final head space is not achieved until the bolt handle is turned down all the way. The design probably used helical locking lugs to allow for chambering imperfect or dirty ammunition and that the closing cam action is distributed over the entire mating faces of both bolt and receiver lugs. This is one reason the bolt closure feels smooth. The angled lugs had no tendency to unwind with chamber pressure since the "angle of repose" of smooth, lubricated steel surfaces is approximately 8 degrees. One advantage was that when the bolt handle was turned up the lugs cleared each other immediately so full effort was applied to the extraction cam. The trigger had a mechanical interlock to prevent firing unless the bolt was fully locked. The location of the safety on the right rear of the receiver has also been copied by most sporting bolt-action rifles since, as it falls easily under the firer's thumb. The trigger pull is ≥ 3lbf (13.3N). One notable design flaw was the leaf spring that powered the ejector, which could break off and render the ejector inoperable. A combat-expedient repair method was to slip a bit of rubber under the bolt stop spring.[19] A redesigned ejector, incorporating a small coil spring in place of the fragile leaf spring, was developed and can be fitted to the M1917 to remedy this issue.
The M1917 was well-suited to the rimless .30-06 Springfield round which came closer in overall length and muzzle energy to the original .276 Enfield high-velocity round for which the rifle had been designed than the rimmed, less powerful .303 British round of the P14. The M1917's barrel had a 1 in 10 in (254mm) twist rate and retained the 5-groove left hand twist Enfield-type rifling of the P14, in contrast to the 4-groove right hand twist rifling of the M1903 Springfield and other US designed arms. The M1917 had a long 26-inch heavyweight barrel compared to the lighter 24-inch barrel of the M1903 Springfield. With the longer sighting plane, the M1917 proved generally more accurate at long distances than the M1903, at the expense of greater weight. The M1917 weighed 9lb 3oz (4.17kg) empty – the M1903 Springfield weighed 8lb 11oz (3.94kg) empty – and a rifle with sling, oiler, and fixed bayonet weighed over 11lb (4.99kg). The M1917's long barrel and issued 16.5in (419mm) blade bayonet proved too lengthy and cumbersome for trench fighting, while its weight and overall length made the rifle difficult to use for some smaller-statured soldiers. During World War I the average height of United States soldiers was 5ft 7.5in (1.71m).[20]
Many M1917 Enfield rifles were refurbished during World War II with newly manufactured High Standard barrels with 4-groove rifling and Johnson Automatics barrels which had 2-groove rifling.[21]
Variants
The M1917 action made from nickel-steel proved very strong, and was used as the basis for a variety of commercial and gunsmith-made sporting rifles in standard and magnum calibers between the world wars and after. Later, Remington Arms redesigned the M1917, removing the "ears" and changing it to cock-on-open, to become the Remington Model 30 series of rifles in the interwar period, which were produced from leftover receivers and barrels.
During the Great Depression Model 30s weren't selling well, and the company decided to develop a M1917 derivative targeted to Central and South American militaries. This found only one buyer in Honduras, where strongman general T. C. Andino elected in 1932 started a military modernization program. Remington Model 1934 rifles based on Model 30 actions with M1917 leftover parts, but fitted with a Mauser-type V sight, more familiar for soldiers using Honduran Mauser Model 1895 already in service, were produced in 7×57mm as service rifles for Honduras.[22] In 1934 500 Remington Model 1934 were delivered and in 1935 2,500.
Additional surplus rifles were bought by European arms distributors and converted to 7.92×57mm Mauser, then sold for use in the civil war in Spain during the 1930s.
X Force was the name given to a portion of the Chinese Army equipped and trained by the US during World War II. One of the weapons given to X Force was the M1917 rifle. These rifles were too big for the small-statured Chinese soldiers so the barrels and stocks were shortened from an overall length of 46 inches for the standard M1917 to a 41-inch rifle.[23]
Norway: In 1952 Norway received 24,992 P-17 rifles from Britain in exchange for their inventory of .303 rifles which were acquired during and after WW2.[35]
In firearm designs, the term single-shot refers to guns that can hold only a single round of ammunition inside and thus must be reloaded manually after every shot. Compared to multi-shot repeating firearms ("repeaters"), single-shot designs have no moving parts other than the trigger, hammer/firing pin or frizzen, and therefore do not need a sizable receiver behind the barrel to accommodate a moving action, making them far less complex and more robust than revolvers or magazine/belt-fed firearms, but also with much slower rates of fire.
A semi-automatic rifle is an auto-loading rifle that fires a single cartridge with each pull of the trigger, the part that fires the bullet. It uses part of the fired cartridge's energy to eject the case and automatically loads another cartridge into its chamber. This is in contrast to bolt-action or lever-action rifles, which require the user to manually chamber a new round before they can fire again, and fully automatic rifles, which fire continuously while the trigger is held down.
Bolt-action is a type of manual firearm action that is operated by directly manipulating the bolt via a bolt handle, most commonly placed on the right-hand side of the firearm. The majority of bolt-action firearms are rifles, but there are also some variants of shotguns and handguns that are bolt-action.
Mauser, originally the Königlich Württembergische Gewehrfabrik, was a German arms manufacturer. Their line of bolt-action rifles and semi-automatic pistols was produced beginning in the 1870s for the German armed forces. In the late 19th and early 20th centuries, Mauser designs were also exported and licensed to many countries, which adopted them as military and civilian sporting firearms. The Gewehr 98 in particular was widely adopted and copied, becoming one of the most copied firearms designs and it is the foundation of many of today's sporting bolt-action rifles. Around 10 millions Gewehr 98 style rifles were produced.
A semi-automatic firearm, also called a self-loading or autoloading firearm, is a repeating firearm whose action mechanism automatically loads a following round of cartridge into the chamber and prepares it for subsequent firing, but requires the shooter to manually actuate the trigger in order to discharge each shot. Typically, this involves the weapon's action utilizing the excess energy released during the preceding shot to unlock and move the bolt, extracting and ejecting the spent cartridge case from the chamber, re-cocking the firing mechanism, and loading a new cartridge into the firing chamber, all without input from the user. To fire again, however, the user must actively release the trigger, and allow it to "reset", before pulling the trigger again to fire off the next round. As a result, each trigger pull only discharges a single round from a semi-automatic weapon, as opposed to a fully automatic weapon, which will shoot continuously as long as the ammunition is replete and the trigger is kept depressed.
The M1903 Springfield, officially the U.S. Rifle, Caliber .30, M1903, is an American five-round magazine-fed, bolt-action service repeating rifle, used primarily during the first half of the 20th century.
The Pedersen device was an experimental weapon attachment for the M1903 Springfield bolt action rifle that allowed it to fire a .30 caliber (7.62 mm) pistol-type cartridge in semi-automatic fire mode. The attachment was developed to allow an infantryman to convert "their rifle to a form of submachine gun or automatic rifle" in approximately 15 seconds.
The .30-06 Springfield cartridge, 7.62×63mm in metric notation, and called the .30 Gov't '06 by Winchester, was introduced to the United States Army in 1906 and later standardized; it remained in military use until the late 1970s. In the cartridge's name, ".30" refers to the nominal caliber of the bullet in inches; "06" refers to the year the cartridge was adopted, 1906. It replaced the .30-03 Springfield, 6mm Lee Navy, and .30-40 Krag cartridges. The .30-06 remained the U.S. Army's primary rifle and machine gun cartridge for nearly 50 years before being replaced by the 7.62×51mm NATO and 5.56×45mm NATO, both of which remain in current U.S. and NATO service. The cartridge remains a very popular sporting round, with ammunition produced by all major manufacturers.
The Winchester Model 70 is a bolt-action sporting rifle. It has an iconic place in American sporting culture and has been held in high regard by shooters since it was introduced in 1936, earning the moniker "The Rifleman's Rifle". The action has some design similarities to Mauser designs and it is a development of the earlier Winchester Model 54, itself being based on a Mauser 98–type action.
The .30-03 Springfield (7.62×65mm) was a short-lived cartridge developed by the United States in 1903, to replace the .30-40 Krag in the new Springfield 1903 rifle. The .30-03 was also called the .30-45, since it used a 45 grain powder charge; the name was changed to .30-03 to indicate the year of adoption. It used a 220 grain roundnose bullet. It was replaced after only three years of service by the .30-06, firing a spitzer bullet that had better ballistic performance.
The M1917 bayonet was designed to be used with the US M1917 Enfield .30 caliber rifle, as well as seven different models of U.S. trench shotguns. The blade was 17 in (43 cm) long with an overall length of 22 in (56 cm). It will not fit the M1903 .30 caliber (Springfield) or the M1 .30 caliber (Garand) US service rifles as they have different bayonet ring (barrel) and attachment stud dimensions.
The Pattern 1913 Enfield (P'13) was an experimental rifle developed by the Royal Small Arms Factory for the British Army as a result of its combat experience in the Second Boer War from 1899 to 1902. The weapon was to serve as a replacement for the Short Magazine Lee–Enfield (SMLE). An advanced chamber design allowed for a high-velocity .276 Enfield rimless round, which was more powerful than the service-issued .303 British cartridge. Introduction of the P'13 was rendered impractical by the outbreak of the First World War.
The Rifle, .303 Pattern 1914 was a British service rifle of the First World War period, principally manufactured under contract by companies in the United States. It was a bolt-action weapon with an integral 5-round magazine. It served as a sniper rifle and as second-line and reserve issue, until declared obsolete in 1947. The Pattern 1914 Enfield was the successor to the Pattern 1913 Enfield experimental rifle and the predecessor of the U.S. Rifle M1917 Enfield.
The origins of the modern British military rifle are within its predecessor the Brown Bess musket. While a musket was largely inaccurate over 100 yards (91 m), due to a lack of rifling and a generous tolerance to allow for muzzle-loading, it was cheap to produce and could be loaded quickly. The use of volley or mass firing by troops meant that the rate of fire took precedence over accuracy.
The Springfield Model 1892–99 Krag–Jørgensen rifle is a Norwegian-designed bolt-action rifle that was adopted in 1892 as the standard United States Army military longarm, chambered for U.S. caliber .30-40 Krag cartridges. All versions and variants were manufactured under license by the Springfield Armory between 1892 and 1903 and famously served as the longarm during the Spanish–American War.
An intermediate cartridge is a rifle/carbine cartridge that has significantly greater power than a pistol cartridge but still has a reduced muzzle energy compared to fully powered cartridges, and therefore is regarded as being "intermediate" between traditional rifle and handgun cartridges.
The Remington Model 30 is a US sporting rifle of the inter-war period based on the military P14/M1917 Enfield rifle action, which was manufactured for the British and US governments during World War I. Initial specimens used surplus military parts with some modifications in order to consume the stock of parts, though further modifications were made as production progressed and later rifles were produced from newly manufactured parts. Most early rifles were in the military .30-06 calibre used in the M1917 but it became available in a variety of chamberings. It was the first high-powered bolt-action sporting rifle produced by Remington. Some would beg to differ as Remington made the Remington Lee factory sporting rifle from 1899-1909, 1446 were built in a variety of calibers.
The Mauser Model 1893 is a bolt-action rifle commonly referred to as the Spanish Mauser, though the model was adopted by other countries in other calibers, most notably the Ottoman Empire. The M1893 was based on the experimental M1892 rifle, which Paul Mauser developed for the Spanish Army as part of a program to correct deficiencies in the earlier 1889, 1890, and 1891 series of Mauser rifles. The M1893 introduced a short staggered-column box magazine that fit flush with the bottom of the stock; the magazine held five smokeless 7×57mm Mauser rounds, which could be reloaded quickly by pushing a stripper clip from the top of the open bolt.
The .276 Enfield (7×60mmRB) was an experimental rebated rim tapered bottlenecked centerfire military rifle cartridge developed in conjunction with the Pattern 1913 Enfield (P'13) rifle. Development was discontinued by the onset of World War I.
↑ Reyeg, Fernando M.; Marsh, Ned B. (December 2011). The Filipino Way of War: Irregular Warfare through the Centuries (Master Thesis). Naval Postgraduate School. pp.79–80, 97. hdl:10945/10681.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
