Automatic Pistol, Caliber .45, M1911 | |
---|---|
Type | Semi-automatic pistol |
Place of origin | United States |
Service history | |
In service | 1911–present |
Used by | See Users |
Wars | As standard U.S. service pistol: In non-US standard use:
|
Production history | |
Designer | John Browning |
Designed |
|
Manufacturer | Colt Manufacturing Company, Smith & Wesson, Norinco, other companies |
Unit cost | $26.38 (1938), [11] equal to $571 now |
Produced | 1911–present |
No. built | 2,734,345 (produced by Colt) 4,294,345 (total including licensed copies) [12] |
Variants |
|
Specifications | |
Mass | 39 oz (1,100 g) empty, with magazine [10] [14] |
Length | 8.5 in (216 mm) [10] |
Barrel length |
|
Cartridge | .45 ACP |
Action | Short recoil operation [10] |
Muzzle velocity | 830 ft/s (253 m/s) [10] |
Effective firing range | 50 m (160 ft) |
Feed system | 7-, 8-, 9-, 10- or 12-round box magazines [15] |
The Colt M1911 (also known as 1911, Colt 1911, Colt .45, or Colt Government in the case of Colt-produced models) is a single-action, recoil-operated, semi-automatic pistol chambered for the .45 ACP cartridge. [10] The pistol's formal U.S. military designation as of 1940 was Automatic Pistol, Caliber .45, M1911 for the original model adopted in March 1911, and Automatic Pistol, Caliber .45, M1911A1 for the improved M1911A1 model which entered service in 1926. The designation changed to Pistol, Caliber .45, Automatic, M1911A1 in the Vietnam War era. [10]
Designed by John Browning, the M1911 is the best-known of his designs to use the short recoil principle in its basic design. The pistol was widely copied, and this operating system rose to become the preeminent type of the 20th century and of nearly all modern centerfire pistols. It is popular with civilian shooters in competitive events such as the International Defensive Pistol Association and International Practical Shooting Confederation. [16]
The U.S. military procured around 2.7 million M1911 and M1911A1 pistols during its service life. The pistol served as the standard-issue sidearm for the United States Armed Forces from 1911 to 1985. [17] It was widely used in World War I, [18] World War II, the Korean War, and the Vietnam War. The M1911A1 was replaced by the adoption of the 9mm Beretta M9 pistol as the standard U.S. military sidearm in 1985. However, the U.S. Army did not officially replace the M1911A1 with the Beretta M9 until October 1986; production and procurement delays kept the 1911A1 in service with some units past 1989. The 1911A1 has never been completely phased out. Modernized derivative variants of the M1911 are still in use by some units of the U.S. Army Special Forces, U.S. Marine Corps and the U.S. Navy.
The M1911 pistol originated in the late 1890s as the result of a search for a suitable self-loading (or semi-automatic) pistol to replace the variety of revolvers in service at the time. [19]
The United States was adopting new firearms at a phenomenal rate; several new pistols and two all-new service rifles (M1892/96/98 Krag and M1895 Navy Lee), as well as a series of revolvers by Colt and Smith & Wesson for the Army and Navy, were adopted just in that decade.[ citation needed ]
The next decade would see a similar pace, including the adoption of several more revolvers and an intensive search for a self-loading pistol that would culminate in the official adoption of the M1911 after the turn of the decade.[ citation needed ]
Hiram S. Maxim had designed a self-loading rifle in the 1880s, but was preoccupied with machine guns. Nevertheless, the application of his principle of using cartridge energy to reload led to several self-loading pistols in 1896. The designs caught the attention of various militaries, each of which began programs to find a suitable one for their forces. In the U.S., such a program would lead to a formal test at the turn of the 20th century. [20]
During the end of 1899 and into 1900, a test of self-loading pistols was conducted, including entries from Mauser (C96 "Broomhandle"), Mannlicher (Mannlicher M1894), and Colt (Colt M1900). [19]
This led to a purchase of 1,000 DWM Luger pistols, chambered in 7.65mm Luger. During field trials, these ran into some problems, especially with stopping power. Other governments had made similar complaints. Consequently, DWM produced an enlarged version of the round, the 9×19mm Parabellum with fifty weapons chambered for it tested by the U.S. Army in 1903. [21]
American units fighting Tausūg guerrillas in the Moro Rebellion in Sulu during the Philippine–American War using the then-standard Colt M1892 revolver, .38 Long Colt, found it to be unsuitable for the rigors of jungle warfare, particularly in terms of stopping power, as the Moros had high battle morale and often used drugs to inhibit the sensation of pain. [22] The U.S. Army briefly reverted to using the M1873 single-action revolver in .45 Colt caliber, which had been standard during the late 19th century; the heavier bullet was found to be more effective against charging tribesmen. [23] The problems prompted the Chief of Ordnance, General William Crozier, to authorize further testing for a new service pistol. [23]
Following the 1904 Thompson-LaGarde pistol round effectiveness tests, Colonel John T. Thompson stated that the new pistol "should not be of less than .45 caliber" and would preferably be semi-automatic in operation. [23] This led to the 1906 trials of pistols from six firearms manufacturing companies (namely, Colt, Bergmann, Deutsche Waffen- und Munitionsfabriken (DWM), Savage Arms, Knoble, Webley, and White-Merrill). [23]
Of the six designs submitted, three were eliminated early on, leaving only the Savage, Colt, and DWM designs chambered in the new .45 ACP (Automatic Colt Pistol) cartridge. [23] These three still had issues that needed correction, but only Colt and Savage resubmitted their designs. There is some debate over the reasons for DWM's withdrawal—some say they felt there was bias and that the DWM design was being used primarily as a "whipping boy" for the Savage and Colt pistols, [24] though this does not fit well with the earlier 1900 purchase of the DWM design over the Colt and Steyr entries. In any case, a series of field tests from 1907 to 1911 were held to decide between the Savage and Colt designs. [23] Both designs were improved between each round of testing, leading up to the final test before adoption. [23]
Among the areas of success for the Colt was a test at the end of 1910 attended by its designer, John Browning. Six thousand rounds were fired from a single pistol over the course of two days. When the gun began to grow hot, it was simply immersed in water to cool it. The Colt gun passed with no reported malfunctions, while the Savage designs had 37. [23]
Following its success in trials, the Colt pistol was formally adopted by the Army on March 29, 1911, when it was designated "Model of 1911", later changed in 1917 to "Model 1911", and then "M1911" in the mid-1920s. The Director of Civilian Marksmanship began manufacture of M1911 pistols for members of the National Rifle Association of America in August 1912. Approximately 100 pistols stamped "N.R.A." below the serial number were manufactured at Springfield Armory and by Colt. [25] The M1911 was formally adopted by the U.S. Navy and Marine Corps in 1913. The .45 ACP "Model of 1911 U.S. Army" was used by both U.S. Army Cavalry troops and infantry soldiers during the United States' Punitive Expedition into Mexico against Pancho Villa in 1916. [26]
By the beginning of 1917, a total of 68,533 M1911 pistols had been delivered to U.S. armed forces by Colt's Patent Firearms Manufacturing Company and the U.S. government's Springfield Armory. However, the need to greatly expand U.S. military forces and the resultant surge in demand for the firearm in World War I saw the expansion of manufacture to other contractors besides Colt and Springfield Armory, including Remington-UMC and North American Arms Co. of Quebec. [27] Several other manufacturers were awarded contracts to produce the M1911, including the National Cash Register Company, the Savage Arms Company, the Caron Brothers Manufacturing of Montreal, the Burroughs Adding Machine Co., Winchester Repeating Arms Company, and the Lanston Monotype Company, but the signing of the Armistice resulted in the cancellation of the contracts before any pistols had been produced. [28]
Battlefield experience in World War I led to some more small external changes, completed in 1924. The new version received a modified type classification, M1911A1, in 1926 with a stipulation that M1911A1s should have serial numbers higher than 700,000 with lower serial numbers designated M1911. [29] The M1911A1 changes to the original design consisted of a shorter trigger, cutouts in the frame behind the trigger, an arched mainspring housing, a longer grip safety spur (to prevent hammer bite), a wider front sight, a shortened hammer spur, and simplified grip checkering (eliminating the "Double Diamond" reliefs). [23] These changes were subtle and largely intended to make the pistol easier to shoot for those with smaller hands. No significant internal changes were made, and parts remained interchangeable between the M1911 and the M1911A1. [23]
Working for the U.S. Ordnance Office, David Marshall Williams developed a .22 training version of the M1911 using a floating chamber to give the .22 long rifle rimfire recoil similar to the .45 version. [23] As the Colt Service Ace, this was available both as a pistol and as a conversion kit for .45 M1911 pistols. [23]
Before World War II, 500 M1911s were produced under license by the Norwegian arms factory Kongsberg Vaapenfabrikk , as Automatisk Pistol Model 1912. Then, production moved to a modified version designated Pistol Model 1914 and unofficially known as "Kongsberg Colt". The Pistol M/1914 is noted for its unusual extended slide stop which was specified by Norwegian ordnance authorities. Twenty-two thousand were produced between 1914 and 1940 but production continued after the German occupation of Norway in 1940 and 10,000 were produced for the German armed forces as Pistole 657 (n). [30]
Between 1927 and 1966, 102,000 M1911 pistols were produced as Sistema Colt Modelo 1927 in Argentina, first by the Dirección General de Fabricaciones Militares. A similar gun, the Ballester–Molina, was also designed and produced. [7]
The M1911 and M1911A1 pistols were also ordered from Colt or produced domestically in modified form by several other nations, including Brazil (M1937 contract pistol), Mexico (M1911 Mexican contract pistol and the Obregón pistol), and Spain (private manufacturers Star and Llama).[ citation needed ]
World War II and the years leading up to it created a great demand. During the war, about 1.9 million units were procured by the U.S. Government for all forces, production being undertaken by several manufacturers, including Remington Rand (900,000 produced), Colt (400,000), Ithaca Gun Company (400,000), Union Switch & Signal (50,000), and Singer (500). New M1911A1 pistols were given a parkerized metal finish instead of bluing, and the wood grip panels were replaced with panels made of brown plastic. The M1911A1 was a favored small arm of both U.S. and allied military personnel during the war. In particular, the pistol was prized by some British commando units and Britain's highly covert Special Operations Executive, as well as South African Commonwealth forces. [31] [32] [33]
The M1911A1 pistol was produced in very large quantities during the war. At the end of hostilities the government cancelled all contracts for further production and made use of existing stocks of weapons to equip personnel. Many of these weapons had seen service use, and had to be rebuilt and refinished prior to being issued. From the mid-1920s to the mid-1950s thousands of 1911s and 1911A1s were refurbished at U.S. arsenals and service depots. These rebuilds consisted of anything from minor inspections to major overhauls. Pistols that were refurbished at government arsenals will usually be marked on the frame/receiver with the arsenal's initials, such as RIA for Rock Island Armory or SA for Springfield Armory.[ citation needed ]
Among collectors today, the Singer-produced pistols in particular are highly prized, commanding high prices even in poor condition. [34]
From 1943 to 1945 a fine-grade russet-leather M1916 pistol belt set was issued to some generals in the U.S. Army. It was composed of a leather belt, leather enclosed flap-holster with braided leather tie-down leg strap, leather two-pocket magazine pouch, and a rope lanyard. The metal buckle and fittings were in gilded brass. The buckle had the seal of the U.S. on the center (or "male") piece and a laurel wreath on the circular (or "female") piece. The pistol was a standard-issue M1911A1 that came with a cleaning kit and three magazines.
From 1972 to 1981 a modified M1911A1 called the RIA M15 General Officer's Model was issued to general officers in the U.S. Army and U.S. Air Force. From 1982 to 1986 the regular M1911A1 was issued. Both came with a black leather belt, open holster with retaining strap, and a two-pocket magazine pouch. The metal buckle and fittings were similar to the M1916 General Officer's Model except it came in gold metal for the Army and in silver metal for the Air Force.
After World War II, the M1911 continued to be a mainstay of the U.S. Armed Forces in the Korean War and the Vietnam War, where it was used extensively by tunnel rats. [35] It was used during Desert Storm in specialized U.S. Army units and U.S. Navy Mobile Construction Battalions (Seabees), and has seen service in both Operation Iraqi Freedom and Operation Enduring Freedom, with U.S. Army Special Forces Groups and Marine Corps Force Reconnaissance Companies. [36]
However, by the late 1970s, the M1911A1 was acknowledged to be showing its age. Under political pressure from Congress to standardize on a single modern pistol design, the U.S. Air Force ran a Joint Service Small Arms Program to select a new semi-automatic pistol using the NATO-standard 9mm Parabellum pistol cartridge. After trials, the Beretta 92S-1 was chosen. The Army contested this result and subsequently ran its own competition in 1981, the XM9 trials, eventually leading to the official adoption of the Beretta 92F on January 14, 1985. [37] [38] [39] By the late 1980s production was ramping up despite a controversial XM9 retrial and a separate XM10 reconfirmation that was boycotted by some entrants of the original trials, cracks in the frames of some pre-M9 Beretta-produced pistols, and despite a problem with slide separation using higher-than-specified-pressure rounds that resulted in injuries to some U.S. Navy special operations operatives. This last issue resulted in an updated model that includes additional protection for the user, the 92FS, and updates to the ammunition used. [40] During the Gulf War of 1990–1991, M1911A1s were deployed with reserve component U.S. Army units sent to participate in Operations Desert Shield and Desert Storm.
By the early 1990s, most M1911A1s had been replaced by the Beretta M9, though a limited number remain in use by special units. The U.S. Marine Corps (USMC) in particular were noted for continuing the use of M1911 pistols for selected personnel in MEU(SOC) and reconnaissance units (though the USMC also purchased over 50,000 M9 pistols.[ citation needed ]) For its part, the United States Special Operations Command (USSOCOM) issued a requirement for a .45 ACP pistol in the Offensive Handgun Weapon System (OHWS) trials. This resulted in the Heckler & Koch OHWS becoming the MK23 Mod 0 Offensive Handgun Weapon System (itself being heavily based on the 1911's basic field strip), beating the Colt OHWS, a much-modified M1911. Dissatisfaction with the stopping power of the 9 mm Parabellum cartridge used in the Beretta M9 has actually promoted re-adoption of pistols based on the .45 ACP cartridge such as the M1911 design, along with other pistols, among USSOCOM units in recent years, though the M9 has been predominant both within SOCOM and in the U.S. military in general. [36] Both U.S. Army Special Forces Units and SFOD-D continue to use modernized M1911s, such as the M45 MEU(SOC) and a modified version of the Colt Rail Gun (a 1911 model with an integrated picatinny rail on the underside of the frame) designated as the M45A1 CQBP (Close Quarters Battle Pistol). [41] [42]
Browning's basic M1911 design has seen very little change throughout its production life. [10] [ page needed ] The basic principle of the pistol is recoil operation. [10] [ page needed ] As the expanding combustion gases force the bullet down the barrel, they give reverse momentum to the slide and barrel which are locked together during this portion of the firing cycle. After the bullet has left the barrel, the slide and barrel continue rearward a short distance. [10] [ page needed ]
At this point, a link pivots the rear of the barrel down, out of locking recesses in the slide, and the barrel is stopped by making contact with the lower barrel lugs against the frame. As the slide continues rearward, a claw extractor pulls the spent casing from the firing chamber and an ejector strikes the rear of the case, pivoting the casing out and away from the pistol through the ejection port. The slide stops its rearward motion then, and is propelled forward again by the recoil spring to strip a fresh cartridge from the magazine and feed it into the firing chamber. At the forward end of its travel, the slide locks into the barrel and is ready to fire again.
However, if the fired round was the last in the magazine, the slide will lock in the rearward position, which notifies the shooter to reload by ejecting the empty magazine and inserting a loaded magazine, and facilitates (by being rearwards) reloading the chamber, which is accomplished by either pulling the slide back slightly and releasing, or by pushing down on the slide stop, which releases the slide to move forward under spring pressure, strip a fresh cartridge from the magazine, and feed it into the firing chamber. [10] [ page needed ]
Other than grip screws there are no fasteners of any type in the 1911 design. The main components of the gun are held in place by the force of the main spring. The pistol can be "field stripped" by partially retracting the slide, removing the slide stop, and removing the barrel bushing. Full disassembly (and subsequent reassembly) of the pistol to its component parts can be accomplished using several manually removed components as tools to complete the disassembly.[ citation needed ]
The military mandated a grip safety and a manual safety. [10] [ page needed ] A grip safety, sear disconnect, slide stop, half cock position, and manual safety (located on the left rear of the frame) are on all standard M1911A1s. [10] Several companies have developed a firing pin block safety. Colt's 80 series uses a trigger operated one and several other manufacturers, including Kimber and Smith & Wesson, use a Swartz firing-pin safety, which is operated by the grip safety. [43] [44] Language cautioning against pulling the trigger with the second finger was included in the initial M1911 manual [45] and later manuals up to the 1940s.
The same basic design has been offered commercially and has been used by other militaries. In addition to the .45 ACP (Automatic Colt Pistol), models chambered for .38 Super, 9×19mm Parabellum, 7.65mm Parabellum, 9mm Steyr, [46] .400 Corbon, and other cartridges were offered. The M1911 was developed from earlier Colt semi-automatic designs, firing rounds such as .38 ACP. The design beat out many other contenders during the government's selection period, during the late 1890s and early 1900s, up to the pistol's adoption. The M1911 officially replaced a range of revolvers and pistols across branches of the U.S. armed forces, though a number of other designs have seen use in certain niches. [47]
Despite being challenged by newer and lighter weight pistol designs in .45 caliber, such as the Glock 21, the SIG Sauer P220, the Springfield XD and the Heckler & Koch USP, the M1911 shows no signs of decreasing popularity and continues to be widely present in various competitive matches such as those of USPSA, IDPA, IPSC, and Bullseye. [13]
In 1986, the USMC Precision Weapon Section (PWS) at Marine Corps Base Quantico began customizing M1911A1s for reconnaissance units. The units served in a new Marine Corps program Marine expeditionary unit (special operations capable) (MEU(SOC)). [48] [49] [50] The pistol was designated the M45 MEU(SOC). [51] Hand-selected Colt M1911A1 frames were gutted, deburred and were then assembled with after-market grip safeties, ambidextrous thumb safeties, triggers, improved high-visibility sights, accurized barrels, grips, and improved Wilson magazines. [49] [52] These hand-made pistols were tuned to specifications and preferences of end users. [53]
In the late 1980s, the Marines laid out a series of specifications and improvements to make Browning's design ready for 21st-century combat, many of which have been included in MEU(SOC) pistol designs, but design and supply time was limited. [53] Discovering that the Los Angeles Police Department was pleased with their special Kimber M1911 pistols, a single source request was issued to Kimber for just such a pistol despite the imminent release of their TLE/RLII models. [54] Kimber shortly began producing a limited number of what would be later termed the Interim Close Quarters Battle pistol (ICQB). Maintaining the simple recoil assembly, 5-inch barrel (though using a stainless steel match grade barrel), and internal extractor, the ICQB is not much different from Browning's original design. [54]
In July 2012, the USMC awarded Colt a $22.5 million contract for up to 12,000 M45A1 pistols with an initial order of 4036 pistols to replace the M45 MEU(SOC) pistol. [55] [56] The Marine Corps issued the M45A1 to Force Reconnaissance companies, Marine Corps Special Operations Command (MARSOC) and Special Reaction Teams from the Provost Marshal’s Office. [51] The new 1911 was designated M45A1 or "Close Quarters Battle Pistol" CQBP. The M45A1 features a dual recoil spring assembly, Picatinny rails and is cerakoted tan in color.
In 2019, the USMC selected the SIG Sauer M18 to replace the M45A1. [57] The Marines began the roll out of the M18 in 2020. [58] The replacement was completed by October 2022. [59]
Since its inception, the M1911 has lent itself to easy customization. Replacement sights, grips, and other aftermarket accessories are the most commonly offered parts. Since the 1950s and the rise of competitive pistol shooting, many companies have been offering the M1911 as a base model for major customization. These modifications can range from changing the external finish, checkering the frame, to hand fitting custom hammers, triggers, and sears. Some modifications include installing compensators and the addition of accessories such as tactical lights and even scopes. [61] A common modification of John Browning's design is to use a full-length guide rod that runs the full length of the recoil spring. This adds weight to the front of the pistol, but does not increase accuracy, and does make the pistol slightly more difficult to disassemble. [62] As of 2002, custom guns could cost over and are built from scratch or on existing base models. [63] Some notable companies offering custom M1911s include Dan Wesson Firearms, Les Baer, Nighthawk Custom, Springfield Custom Shop, and Wilson Combat. [64] IPSC models are offered by BUL Armory, Strayer Voigt Inc (Infinity Firearms).[ citation needed ]
Many military and law enforcement organizations in the U.S. and other countries continue to use (often modified) M1911A1 pistols including Los Angeles Police Department SWAT and S.I.S., the FBI Hostage Rescue Team, FBI regional SWAT teams, and 1st Special Forces Operational Detachment—Delta (Delta Force).[ citation needed ]
The M1911A1 is popular among the general public in the U.S. for practical and recreational purposes. The pistol is commonly used for concealed carry thanks in part to a single-stack magazine (which makes for a thinner pistol that is, therefore, easier to conceal), personal defense, target shooting, and competition as well as collections. Numerous aftermarket accessories allow users to customize the pistol to their liking. There are a growing number of manufacturers of M1911-style pistols and the model continues to be quite popular for its reliability, simplicity, and patriotic appeal. Various tactical, target and compact models are available. Price ranges from a low end of around $400 for basic models imported from Turkey (TİSAŞ and GİRSAN) and the Philippines (Armscor, Metro Arms, and SAM Inc.) to more than $4,000 for the best competition or tactical versions (Wilson Combat, Ed Brown, Les Baer, Nighthawk Custom, and Staccato). [65]
Due to an increased demand for M1911 pistols among Army Special Operations units, who are known to field a variety of M1911 pistols, the U.S. Army Marksmanship Unit began looking to develop a new generation of M1911s and launched the M1911-A2 project in late 2004. [13] The goal was to produce a minimum of seven variants with various sights, internal and external extractors, flat and arched mainspring housings, integral and add-on magazine wells, a variety of finishes and other options, with the idea of providing the end-user a selection from which to select the features that best fit their missions. [13] The AMU performed a well-received demonstration of the first group of pistols to the Marine Corps at Quantico and various Special Operations units at Ft. Bragg and other locations. [13] The project provided a feasibility study with insight into future projects. [13] Models were loaned to various Special Operations units, the results of which are classified. An RFP was issued for a Joint Combat Pistol but it was ultimately canceled. [13] Currently,[ when? ] units are experimenting with an M1911 pistol in .40 S&W, which will incorporate lessons learned from the A2 project. Ultimately, the M1911A2 project provided a testbed for improving existing M1911s. An improved M1911 variant becoming available in the future is a possibility. [13]
The Springfield Custom Professional Model 1911A1 pistol is produced under contract by Springfield Armory for the FBI regional SWAT teams and the Hostage Rescue Team. [66] This pistol is made in batches on a regular basis by the Springfield Custom Shop, and a few examples from most runs are made available for sale to the general public at a selling price of approximately US$2,700 each.[ citation needed ]
On March 18, 2011, the U.S. state of Utah—as a way of honoring M1911 designer John Browning, who was born and raised in the state—adopted the Browning M1911 as the "official firearm of Utah". [117]
John Moses Browning was an American firearm designer who developed many varieties of military and civilian firearms, cartridges, and gun mechanisms, many of which are still in use around the world. He made his first firearm at age 13 in his father's gun shop and was awarded the first of his 128 firearm patents on October 7, 1879, at the age of 24. He is regarded as one of the most successful firearms designers of the 19th and 20th centuries and a pioneer of modern repeating, semi-automatic, and automatic firearms.
A semi-automatic pistol is a repeating handgun that automatically ejects and loads cartridges in its chamber after every shot fired, but only one round of ammunition is fired each time the trigger is pulled. The pistol's fire control group disconnects the trigger mechanism from the firing pin/striker until the trigger has been released and reset manually, unlike the self-cycled firing mechanism in fully automatic pistols.
The .45 ACP, also known as .45 Auto, .45 Automatic, or 11.43×23mm is a rimless straight-walled handgun cartridge designed by John Moses Browning in 1904, for use in his prototype Colt semi-automatic pistol. After successful military trials, it was adopted as the standard chambering for Colt's M1911 pistol. The round was developed due to a lack of stopping power experienced in the Moro Rebellion in places like Sulu. The issued ammunition, .38 Long Colt, had proved inadequate, motivating the search for a better cartridge. This experience and the Thompson–LaGarde Tests of 1904 led the Army and the Cavalry to decide that a minimum of .45 caliber was required in a new handgun cartridge.
The Heckler & Koch MK 23, MK 23 MOD 0, Mark 23, or USSOCOM MARK 23 is a semi-automatic large-frame pistol chambered in .45 ACP, designed specifically to be an offensive pistol. The USSOCOM version of the MK23 came paired with a laser aiming module (LAM) and suppressor. The USSOCOM MK23 was adopted by the United States Special Operations Command (USSOCOM) for special operations units, beating out the nearest competitor, Colt's OHWS. Development of the pistol began in 1991 as special operations representatives identified the need for an "Offensive Handgun Weapons System—Special Operations Peculiar", and delivery of the pistols began in May 1996 to the special operation units.
The Vis or Vis 35 is a Polish 9×19mm caliber, single-action, semi-automatic pistol. Its design was inspired by the Colt 1911 pistol designed by American John Moses Browning.
The Remington Model 51 is a small pocket pistol designed by John Pedersen and manufactured by Remington Arms in the early 20th century for the American civilian market. Remington manufactured approximately 65,000 Model 51 pistols in .32 ACP and .380 ACP calibers from 1918 to 1926, though small numbers were assembled into the mid-1930s.
The Beretta M9, officially the Pistol, Semiautomatic, 9mm, M9, is the designation for the Beretta 92FS semi-automatic pistol used by the United States Armed Forces. The M9 was adopted by the United States military as their service pistol in 1985.
The M15 General Officers is a .45 ACP pistol developed by the U.S. Army's Rock Island Arsenal from stock M1911 pistols as a replacement for the aging Colt Model 1903 and Model 1908 Pocket Hammerless pistols. The pistol was issued to United States Army general officers as a personal weapon.
The M1917 Revolvers were six-shot, .45 ACP, large frame double action revolvers adopted by the United States Military in 1917, to supplement the standard M1911 pistol during World War I. There were two variations of the M1917, one made by Colt and the other by Smith & Wesson. They used moon-clips to hold the cartridges in position, facilitate reloading, and to aid in extraction since revolvers had been designed to eject rimmed cartridges and .45 ACP rounds were rimless for use with the magazine-fed M1911. After World War I, they gained a strong following among civilian shooters. A commercial rimmed cartridge, the .45 Auto Rim, was also developed, so M1917 revolvers could eject cartridge cases without using moon-clips.
The Colt Model 1903 Pocket Hammerless is a .32 ACP caliber, self-loading, semi-automatic pistol designed by John Browning and built by Colt Patent Firearms Manufacturing Company of Hartford, Connecticut. The Colt Model 1908 Pocket Hammerless is a variant introduced five years later in .380 ACP caliber. Despite the title "hammerless", the Model 1903 does have a hammer. The hammer is covered and hidden from view under the rear of the slide, this allows the pistol to be carried in and withdrawn from a pocket quickly and smoothly without snagging.
The Colt OHWS was a semi-automatic pistol created by Colt to compete for the United States Special Operations Command Offensive Handgun Weapon System (OHWS) tender. The winner of this competition would become the standard-issue handgun for most US special forces groups. The OHWS contract was awarded to Heckler & Koch for their MK23 Mod 0 pistol, and Colt scrapped the project.
The Joint Service Small Arms Program, abbreviated JSSAP, was created to coordinate weapon standardization between the various United States armed service branches.
The Colt Model 1900 is a short-recoil operated "self-loading", or semi-automatic .38 caliber handgun introduced by Colt's Manufacturing Company at the turn of the 20th century. The M1900 was the first firearm to be chambered in .38 ACP and was the first handgun to utilize short-recoil operation.
The Colt Commander is a single-action, semi-automatic, magazine-fed, and recoil-operated handgun based on the John M. Browning–designed M1911. It was the first mass-produced American pistol with an aluminium alloy frame and the first Colt pistol to be chambered in 9mm Parabellum.
The Grizzly Win Mag pistols were conceived, invented, designed, engineered and developed in the 1980s by the sole inventor, Perry Arnett, who licensed his patent for an interchangeable caliber semi-automatic pistol to L.A.R. Manufacturing Inc. Perry Arnett's designs were initially flawed and were improved upon by Heinz Augat. The L.A.R. Grizzly was one of the most powerful semi-automatic pistol ever commercially produced, after the Mateba Unica 6.
The Ballester–Molina is a pistol designed and built by the Argentine company Hispano Argentina Fábrica de Automóviles SA (HAFDASA). From 1938 to 1940 it bore the name Ballester–Rigaud.
The MEU(SOC) pistol, officially designated the M45 MEUSOC, is a magazine-fed, recoil-operated, single-action, semiautomatic pistol chambered for the .45 ACP cartridge. It is a variant of the M1911 for use by the Force Recon Element of the United States Marine Corps' Marine Expeditionary Units from 1985 until 2022. It is assigned NATO Stock Number 1005-01-370-7353.
The Colt New Service is a large frame, large caliber, double-action revolver made by Colt from 1898 until 1941. Made in various calibers, the .45 Colt version with a 5½" barrel, was adopted by the U.S. Armed Forces as the Model 1909.
The Colt Officer's Model or Colt Officer's ACP is a single-action, semi-automatic, magazine-fed, and recoil-operated handgun based on the John M. Browning designed M1911. It was introduced in 1985 as a response from Colt to numerous aftermarket companies making smaller versions of the M1911 pistol.