Glowplug

Last updated
Glow plug.JPG
A typical glowplug
Hot Glowplug powered by 12V battery.jpg
Glowplug in operation

In a diesel engine, a glowplug (also spelled glow plug) is a heating device used to aid starting of the engine in cold weather. This device is a pencil-shaped piece of metal with an electric heating element at the tip.

Contents

A glowplug system consists of either a single glowplug in the inlet manifold, or one glowplug per cylinder. In older systems, the driver is required to manually activate the glowplug system and wait approximately 20 seconds before starting the engine. Newer systems automatically activate the glowplug(s) before the engine is started and have a quicker warm-up time.

Design

Glow plugs installed in a small engine (beneath the horizonal bar Glow plugs.jpg
Glow plugs installed in a small engine (beneath the horizonal bar

Glowplugs are typically used as starting-aid devices, when the engine is being cranked by a starter motor, and in most cases switched off when the engine has reached a defined minimum operating temperature. Diesel engines, unlike common spark-ignition engines, do not use spark plugs to ignite the air-fuel mixture. Instead, they rely solely on compression to raise the temperature of the air to a point where the fuel combusts spontaneously when introduced to the hot, high pressure air. When the engine's surroundings are cold, the air's thermal energy – that it has previously received from the starter motor's compression work – is absorbed by the cylinder head and engine block, and eventually transferred to the air surrounding the engine. When the temperature of the air surrounding the engine comes below a certain value, depending upon cylinder head design, (40 °C for precombustion chamber injected, 20 °C for swirl chamber injected, and 0 °C for direct injected engines), the engine loses too much compression heat to reliably initiate combustion, and the engine fails to start. Glow plugs are used to help overcome this issue by introducing additional heat energy into the combustion chambers. [1]

A glowplug resembles a short metal pencil. The heating element is fitted into its tip. Glowplug filaments must be made of certain materials, such as platinum and iridium, that resist oxidation and high temperature. Certain diesel engines (especially direct-injection engines) do not use starting-aid devices such as glowplugs. Engines with a displacement of more than one litre per cylinder usually incorporate a flame-start system rather than glowplugs, if a starting aid system is required. [1]

Activation method

Glowplug indicator light in the dashboard of a car Glowplug.jpg
Glowplug indicator light in the dashboard of a car

For older vehicles, the driver needs to activate the glow plug for approximately 20 seconds before starting the engine. This is achieved by leaving the ignition switch in the "on" position, and only moving it to "start" once the glowplug has finished pre-heating the engine. Once the engine is running, some cars continue to use the glowplugs until the engine has reached its operating temperature, in order to reduce the diesel exhaust emissions. Similarly, some engines re-activate the glowplugs if the temperature of an engine under light loads reduces below a certain threshold, in order to improve the efficiency of the engine.

Many modern engines automatically activate the glowplugs when the operator unlocks the vehicle or opens the door to the car, thus simplifying the process and shortening the waiting time the operator has to wait before the engine will start. In addition, the time needed to pre-heat the engine is typically 6-8 seconds. [2] Some vehicles include a warning light on the dashboard that extinguished once the engine was pre-heated.

Glow plugs for model engines

Glow plugs in small model engines are quite different to those discussed above for full-size diesel engines. Full-size engines only use the glow plug for starting. Model engines use a glow plug as an integral part of the ignition system for the methanol-based fuel used by these engines.

Model engine glow plugs are also used to ignite pyrotechnic devices such as flash powder and smoke generators. [3]

See also

Related Research Articles

<span class="mw-page-title-main">Compression ratio</span> Ratio of the volume of a combustion chamber from its largest capacity to its smallest capacity

The compression ratio is the ratio between the volume of the cylinder and combustion chamber in an internal combustion engine at their maximum and minimum values.

<span class="mw-page-title-main">Diesel engine</span> Type of internal combustion engine

The diesel engine, named after Rudolf Diesel, is an internal combustion engine in which ignition of the fuel is caused by the elevated temperature of the air in the cylinder due to mechanical compression; thus, the diesel engine is called a compression-ignition engine. This contrasts with engines using spark plug-ignition of the air-fuel mixture, such as a petrol engine or a gas engine.

<span class="mw-page-title-main">Fuel injection</span> Feature of internal combustion engines

Fuel injection is the introduction of fuel in an internal combustion engine, most commonly automotive engines, by the means of an injector. This article focuses on fuel injection in reciprocating piston and Wankel rotary engines.

A stratified charge engine describes a certain type of internal combustion engine, usually spark ignition (SI) engine that can be used in trucks, automobiles, portable and stationary equipment. The term "stratified charge" refers to the working fluids and fuel vapors entering the cylinder. Usually the fuel is injected into the cylinder or enters as a fuel rich vapor where a spark or other means are used to initiate ignition where the fuel rich zone interacts with the air to promote complete combustion. A stratified charge can allow for slightly higher compression ratios without "knock," and leaner air/fuel ratio than in conventional internal combustion engines.

<span class="mw-page-title-main">Four-stroke engine</span> Internal combustion engine type

A four-strokeengine is an internal combustion (IC) engine in which the piston completes four separate strokes while turning the crankshaft. A stroke refers to the full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:

  1. Intake: Also known as induction or suction. This stroke of the piston begins at top dead center (T.D.C.) and ends at bottom dead center (B.D.C.). In this stroke the intake valve must be in the open position while the piston pulls an air-fuel mixture into the cylinder by producing vacuum pressure into the cylinder through its downward motion. The piston is moving down as air is being sucked in by the downward motion against the piston.
  2. Compression: This stroke begins at B.D.C, or just at the end of the suction stroke, and ends at T.D.C. In this stroke the piston compresses the air-fuel mixture in preparation for ignition during the power stroke (below). Both the intake and exhaust valves are closed during this stage.
  3. Combustion: Also known as power or ignition. This is the start of the second revolution of the four stroke cycle. At this point the crankshaft has completed a full 360 degree revolution. While the piston is at T.D.C. the compressed air-fuel mixture is ignited by a spark plug or by heat generated by high compression, forcefully returning the piston to B.D.C. This stroke produces mechanical work from the engine to turn the crankshaft.
  4. Exhaust: Also known as outlet. During the exhaust stroke, the piston, once again, returns from B.D.C. to T.D.C. while the exhaust valve is open. This action expels the spent air-fuel mixture through the exhaust valve.

In spark ignition internal combustion engines, knocking occurs when combustion of some of the air/fuel mixture in the cylinder does not result from propagation of the flame front ignited by the spark plug, but when one or more pockets of air/fuel mixture explode outside the envelope of the normal combustion front. The fuel-air charge is meant to be ignited by the spark plug only, and at a precise point in the piston's stroke. Knock occurs when the peak of the combustion process no longer occurs at the optimum moment for the four-stroke cycle. The shock wave creates the characteristic metallic "pinging" sound, and cylinder pressure increases dramatically. Effects of engine knocking range from inconsequential to completely destructive.

Pre-ignition in a spark-ignition engine is a technically different phenomenon from engine knocking, and describes the event wherein the air/fuel mixture in the cylinder ignites before the spark plug fires. Pre-ignition is initiated by an ignition source other than the spark, such as hot spots in the combustion chamber, a spark plug that runs too hot for the application, or carbonaceous deposits in the combustion chamber heated to incandescence by previous engine combustion events.

Indirect injection in an internal combustion engine is fuel injection where fuel is not directly injected into the combustion chamber.

Dieseling or engine run-on is a condition that can occur in spark-plug-ignited, gasoline-powered internal combustion engines, whereby the engine keeps running for a short period after being turned off, drawing fuel through the carburetor, into the engine and igniting it without a spark.

Homogeneous Charge Compression Ignition (HCCI) is a form of internal combustion in which well-mixed fuel and oxidizer are compressed to the point of auto-ignition. As in other forms of combustion, this exothermic reaction releases energy that can be transformed in an engine into work and heat.

<span class="mw-page-title-main">Hot-bulb engine</span> Internal combustion engine

The hot-bulb engine is a type of internal combustion engine in which fuel ignites by coming in contact with a red-hot metal surface inside a bulb, followed by the introduction of air (oxygen) compressed into the hot-bulb chamber by the rising piston. There is some ignition when the fuel is introduced, but it quickly uses up the available oxygen in the bulb. Vigorous ignition takes place only when sufficient oxygen is supplied to the hot-bulb chamber on the compression stroke of the engine.

<span class="mw-page-title-main">Model engine</span>

A model engine is a small internal combustion engine typically used to power a radio-controlled aircraft, radio-controlled car, radio-controlled boat, free flight, control line aircraft, or ground-running tether car model.

<span class="mw-page-title-main">Glow plug (model engine)</span>

A glow plug engine, or glow engine, is a type of small internal combustion engine typically used in model aircraft, model cars and similar applications. The ignition is accomplished by a combination of heating from compression, heating from a glow plug and the catalytic effect of the platinum within the glow plug on the methanol within the fuel.

<span class="mw-page-title-main">Push start</span>

Push starting, also known as bump starting, roll starting, clutch starting, popping the clutch or crash starting, is a method of starting a motor vehicle with an internal combustion engine and with a manual transmission and with a mechanical fuel pump and a mechanically driven generator or alternator. By pushing or letting the vehicle roll downhill then engaging the clutch at the appropriate speed the engine will turn over and start. The technique is most commonly employed when other starting methods are unavailable.

Trionic T5.5 is an engine management system in the Saab Trionic range. It controls ignition, fuel injection and turbo boost pressure. The system was introduced in the 1993 Saab 9000 2.3 Turbo with B234L and B234R engine.

<span class="mw-page-title-main">Carbureted compression ignition model engine</span>

A carbureted compression ignition model engine, popularly known as a model diesel engine, is a simple compression ignition engine made for model propulsion, usually model aircraft but also model boats. These are quite similar to the typical glow-plug engine that runs on a mixture of methanol-based fuels with a hot wire filament to provide ignition. Despite their name, their use of compression ignition, and the use of a kerosene fuel that is similar to diesel, model diesels share very little with full-size diesel engines.

Internal combustion engines come in a wide variety of types, but have certain family resemblances, and thus share many common types of components.

<span class="mw-page-title-main">Cold start (automotive)</span>

A cold start is an attempt to start a vehicle's engine when it is cold, relative to its normal operating temperature, often due to normal cold weather. A cold start situation is commonplace, as weather conditions in most climates will naturally be at a lower temperature than the typical operating temperature of an engine.

<span class="mw-page-title-main">Internal combustion engine</span> Engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber

An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to. This replaced the external combustion engine for applications where the weight or size of an engine were more important.

<span class="mw-page-title-main">4 VD 14,5/12-1 SRW</span> Motor vehicle engine

The 4 VD 14,5/12-1 SRW is an inline four-cylinder diesel engine produced by the VEB IFA Motorenwerke Nordhausen from 1967 to 1990. The engine was one of the standard modular engines for agricultural and industrial use in the Comecon-countries. Approximately one million units were made.

References

  1. 1 2 Konrad Reif (ed.): Dieselmotor-Management im Überblick. 2nd edition. Springer, Wiesbaden 2014, ISBN   978-3-658-06554-6. p. 136
  2. ↑ Robert Bosch GmbH (2010-03-24). "Glow Plugs". Bosch. Archived from the original on 2012-07-16. Retrieved 2012-07-07.
  3. ↑ "Glo-Plugs". TheatreFX. Archived from the original on 19 April 2019. Retrieved 9 January 2016.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.