Smith-class destroyer

Last updated

USSFlusserDD20.jpg
USS Flusser
Class overview
NameSmith class
Operators US flag 48 stars.svg United States Navy
Preceded by Truxtun class
Succeeded by Paulding class
SubclassesFlusser
Built1908–1910
In commission1909–1919
Completed5
Scrapped5
General characteristics
Type Destroyer
Displacement
  • 700 long tons (710 t) (normal)
  • 902 long tons (916 t) (full load)
Length293 ft 10 in (89.56 m)
Beam26 ft 0 in (7.92 m)
Draft8 ft 0 in (2.44 m)
Installed power
Propulsion3 × shafts
Speed28 knots (52 km/h; 32 mph) (design)
Range2,800 nautical miles (5,200 km) at 10 knots (19 km/h; 12 mph)
Capacity304 long tons (309 t) coal (fuel)
Complement
  • 4 officers
  • 83 enlisted men
Armament

The Smith-class destroyers were the first ocean-going torpedo-boat destroyers in the United States Navy, and the first to be driven by steam turbines instead of the reciprocating engines fitted in the sixteen earlier and much smaller torpedo-boat destroyers ordered under the Act of 4 May 1898. Flusser and Reid are sometimes considered to be Flusser-class ships. Also, since Flusser was completed first, some period documentation refers to the entire class as Flussers. [1]

Contents

The first three of the class were ordered under the Act of 29 June 1906 "to have the highest practical speed, and to cost, exclusive of armament, not to exceed seven hundred and fifty thousand dollars each". The remaining pair were ordered under the Act of 7 March 1907 "to have the highest practical speed, and to cost, exclusive of armament, not to exceed eight hundred thousand dollars each". [1]

All of the ships served as convoy escorts in World War I, and several attacked U-boats. The latter four vessels were all sold in November 1919 following the end of World War I; Smith survived another two years as a bombing target until scrapped. [2]

Design

These were the first turbine-powered destroyers in US service, and the last to be coal-fired. Surprisingly, turbines were dictated by cost; when bids were opened, all of the turbine-powered proposals were lower than all of the reciprocating proposals. [1] The Smiths were greatly enlarged Truxtuns; at 900 tons full load they were 50% larger. The extra displacement went into increased armament and more powerful machinery to maintain the Truxtuns' 28- knot (52 km/h; 32 mph) speed. The raised forecastle improved seaworthiness. Also, the coal capacity was increased to 304 tons, nearly half the total full load displacement of the previous class. The increased size and range meant that these were the US Navy's first truly ocean-going destroyers, capable of operating with battleships on long voyages. The seizure of the Philippines in the Spanish–American War and the acquisition of Hawaii, both in 1898, had shown the need for long-range ships. Shortly before the Smith class entered service, the Great White Fleet of 1907–09 demonstrated that the US Navy was prepared to operate far from home. Ironically, these destroyers would quickly be nicknamed "flivvers" (after the small and shaky Model T Ford) for their small size when the subsequent "thousand tonners" (Cassin through Sampson classes) entered service in 1913. [3]

It was recognized that destroyers would now be fighting other destroyers rather than torpedo boats, and that destroyers also needed more offensive (aka torpedo) capability to take over the torpedo boats' role, while retaining the range and seakeeping qualities to operate with the battle fleet. [1] This was the beginning of the multiple missions that US destroyers would eventually be expected to perform, including anti-submarine warfare beginning in World War I and anti-air warfare beginning in the 1930s.

Armament

Compared with the Truxtuns, the gun armament was increased to five 3-inch (76 mm)/50 caliber guns; [4] smaller guns were deleted to maximize the number of larger guns. This followed a trend set by the rearmament of the British River-class destroyers in 1906, which reflected the "all big gun" design of the battleship HMS Dreadnought. A third 18-inch (457 mm) torpedo tube was added, and one torpedo reload per tube was provided. In 1911 it was noted that torpedoes fired from the stern mount at a ship's speed much above 20 knots ran erratically due to the stern wave deflecting them. [1]

In 1916, all had their single torpedo tubes replaced by twin mounts (with no reloads) while one 3-inch gun was removed. [2] This was an easy upgrade, as the new design twin mounts actually weighed less than the older single mounts. [1] They were equipped with one or two depth charge racks for convoy escort during World War I. [5]

Engineering

Unlike the earlier 16 destroyers, these turbine-driven vessels were triple-screw. The ships' steam turbines were direct drive and arranged in a similar manner to Sir Charles Parsons' Turbinia , with a high-pressure turbine on the center shaft exhausting to two low-pressure turbines on the outboard shafts. [6] Cruising turbines were also fitted on the outboard shafts to improve fuel economy at low speeds, a problem that would plague turbine-powered ships until fully geared turbines and higher steam pressures and temperatures were introduced during World War I. [7] To attempt to find a middle ground between the turbines' high efficient speed and the propellers' low efficient speed, the maximum shaft speed was 724 rpm, over twice that of a modern ship. [1]

All had two widely spaced pairs of funnels except for Smith, which had the first and fourth funnels separated from the middle pair.

Smith had four Mosher coal-fired boilers supplying steam to three steam turbines totaling 10,000  shp (7,500 kW) (design). [1] She made 28.35 kn (32.6 mph; 52.5 km/h) on trials at 9,946 shp (7,417 kW). Normal coal capacity was 304 tons. [1]

Ships in class

Ships of the Smith destroyer class [2] [6]
NameHull no.ShipyardLaid downLaunchedComm-
issioned		Decomm-
issioned		Fate
Smith DD-17 William Cramp & Sons, Philadelphia 18 March 190820 April 190926 November 19092 September 1919Bombing target until
sold 20 December 1921 to Joseph G. Hitner for scrapping
Lamson DD-18William Cramp & Sons18 March 190816 June 190910 February 191015 July 1919Sold November 1919 for scrapping
Preston DD-19 New York Shipbuilding, Camden, New Jersey 28 April 190814 July 190921 December 190917 July 1919Sold November 1919 to T. A. Scott of New London, Connecticut for scrapping
Flusser DD-20 Bath Iron Works, Bath, Maine 3 August 190820 July 190928 October 190914 July 1919Sold November 1919 for scrapping
Reid DD-21Bath Iron Works3 August 190817 August 19093 December 190931 July 1919Sold November 1919 to T. A. Scott of New London, Connecticut for scrapping

See also

Related Research Articles

<i>Clemson</i>-class destroyer Destroyer class of the US Navy

The Clemson class was a series of 156 destroyers which served with the United States Navy from after World War I through World War II.

<i>Wickes</i>-class destroyer Destroyer class of the US Navy

The Wickes-class destroyers were a class of 111 destroyers built by the United States Navy in 1917–19. Along with the 6 preceding Caldwell-class and 156 subsequent Clemson-class destroyers, they formed the "flush-deck" or "four-stack" type. Only a few were completed in time to serve in World War I, including USS Wickes, the lead ship of the class.

<i>Beagle</i>-class destroyer

The Beagle class was a class of sixteen destroyers of the Royal Navy, all ordered under the 1908-1909 programme and launched in 1909 and 1910. The Beagles served during World War I, particularly during the Dardanelles Campaign of 1915.

<i>Truxtun</i>-class destroyer Destroyer class of the US Navy

Three Truxtun-class destroyers were built for the United States Navy. Part of the original 16 destroyers authorized by Congress on 4 May 1898 for the fiscal year 1899 program, they were commissioned in 1902. They were very similar to their Bainbridge-class contemporaries, except for mounting six 6-pounder (57 mm) guns instead of five. They were considered the most successful of the first 16 US Navy destroyers, and were succeeded by the larger Smith class.

<i>Bainbridge</i>-class destroyer Destroyer class of the US Navy

The Bainbridge-class destroyers were a class of United States Navy Torpedo Boat Destroyers (TBDs) built between 1899 and 1903. The first class so designated, they comprised the first 13 of 16 TBDs authorized by Congress in 1898 following the Spanish–American War. One ship of the class was lost at sea during service in World War I: Chauncey, which collided with the British merchant ship SS Rose in 1917. The balance were decommissioned in 1919 and sold postwar in 1920, eleven to Joseph G. Hitner of Philadelphia, and the Hopkins to the Denton Shore Lumber Company in Tampa, Florida.

<i>Paulding</i>-class destroyer Destroyer class of the US Navy

The Paulding-class destroyers were a series of United States Navy destroyers derived from the Smith class with the torpedo tubes increased from three to six via twin mounts. They were the first destroyers in the US Navy with oil-fired boilers. The 21 Pauldings doubled the number of destroyers in the US Navy. The Paulding class derived its name from the class's lead ship, Paulding, named for Rear Admiral Hiram Paulding (1797–1878). Like the Smiths, they were nicknamed "flivvers" after the small and shaky Model T Ford once the larger "thousand tonner" destroyers entered service.

<i>Cassin</i>-class destroyer Destroyer class of the US Navy

Four destroyers in the United States Navy comprised the Cassin class. All served as convoy escorts during World War I. The Cassins were the first of five "second-generation" 1000-ton four-stack destroyer classes that were front-line ships of the Navy until the 1930s. They were known as "thousand tonners" for their normal displacement, while the previous classes were nicknamed "flivvers" for their small size, after the Model T Ford.

<i>Aylwin</i>-class destroyer Destroyer class of the US Navy

The Aylwin class was a class of four destroyers in the United States Navy; all served as convoy escorts during World War I. The Aylwins were the second of five "second-generation" 1000-ton four-stack destroyer classes that were front-line ships of the Navy until the 1920s. They were known as "thousand tonners". All were scrapped in 1935 to comply with the London Naval Treaty.

<i>OBrien</i>-class destroyer Destroyer class of the US Navy

The O'Brien class of destroyers was a class of six ships designed by and built for the United States Navy shortly before the United States entered World War I. The O'Brien class was the third of five classes of destroyers that were known as the "thousand tonners", because they were the first U.S. destroyers over 1,000 long tons (1,016 t) displacement.

<i>Tucker</i>-class destroyer Destroyer class of the US Navy

The Tucker class of destroyers was a ship class of six ships designed by and built for the United States Navy shortly before the United States entered World War I. The Tucker class was the fourth of five classes of destroyers that were known as the "thousand tonners", because they were the first U.S. destroyers over 1,000 long tons (1,016 t) displacement.

<i>Sampson</i>-class destroyer Destroyer class of the US Navy

The Sampson-class destroyers served in the United States Navy during World War I. Commissioned in 1916 and 1917, the class was a modification of the O'Brien and Tucker classes, with the number of 21-inch (533 mm) torpedo tubes increased from four twin-mounts to four triple-mounts. The Sampsons were the final six ships of the 26 "thousand tonner" destroyers. They were the largest and most heavily armed of the "thousand tonners", and the subsequent "flush deck" classes differed mainly in hull design and the engineering plant.

USS <i>Flusser</i> (DD-289) Clemson-class destroyer

USS Flusser (DD-289) was a Clemson-class destroyer built for the United States Navy during World War I.

<i>Caldwell</i>-class destroyer Destroyer class of the US Navy

The Caldwell class was a class of six "flush deck" United States Navy destroyers built during World War I and shortly after. Four served as convoy escorts in the Atlantic; the other two were completed too late for wartime service. Two were scrapped during the 1930s, but four survived to serve throughout World War II, three of these in service with the Royal Navy under the Destroyers for Bases Agreement and the fourth as a high speed transport.

<i>Farragut</i>-class destroyer (1934) 1934 Destroyer class of the US Navy

The Farragut-class destroyers were a class of eight 1,365-ton destroyers in the United States Navy and the first US destroyers of post-World War I design. Their construction, along with the Porter class, was authorized by Congress on 29 April 1916, but funding was delayed considerably. Limited to 1,500 tons standard displacement by the provisions of the London Naval Treaty of 1930, the ships were laid down beginning in 1932 and were completed by 1935. After 12 years since the last of the previous class of American destroyers was commissioned, the Farraguts were commissioned in 1934 and 1935.

<i>Porter</i>-class destroyer Destroyer class of the US Navy

The Porter-class destroyers were a class of eight 1,850-ton large destroyers in the United States Navy. Like the preceding Farragut-class, their construction was authorized by Congress on 26 April 1916, but funding was delayed considerably. They were designed based on a 1,850-ton standard displacement limit imposed by the London Naval Treaty; the treaty's tonnage limit allowed 13 ships of this size, and the similar Somers class was built later to meet the limit. The first four Porters were laid down in 1933 by New York Shipbuilding in Camden, New Jersey, and the next four in 1934 at Bethlehem Steel Corporation in Quincy, Massachusetts. All were commissioned in 1936 except Winslow, which was commissioned in 1937. They were built in response to the large Fubuki-class destroyers that the Imperial Japanese Navy was building at the time and were initially designated as flotilla leaders. They served extensively in World War II, in the Pacific War, the Atlantic, and in the Americas. Porter was the class' only loss, in the Battle of the Santa Cruz Islands on 26 October 1942.

<i>Somers</i>-class destroyer Destroyer class of the US Navy

The Somers-class destroyer was a class of five 1850-ton United States Navy destroyers based on the Porter class. They were answers to the large destroyers that the Japanese navy was building at the time, and were initially intended to be flotilla leaders. They were laid down from 1935–1936 and commissioned from 1937–1939. They were built to round-out the thirteen destroyers of 1,850 tons standard displacement allowed by the tonnage limits of the London Naval Treaty, and were originally intended to be repeat Porters. However, new high-pressure, high-temperature boilers became available, allowing the use of a single stack. This combined with weight savings allowed an increase from two quadruple center-line torpedo tube mounts to three. However, the Somers class were still over-weight and top-heavy. This was the first US destroyer class to use 600 psi (4,100 kPa) steam superheated to 850 °F (454 °C), which became standard for US warships built in the late 1930s and World War II.

<span class="mw-page-title-main">3-inch/50-caliber gun</span> Naval gun

The 3"/50 caliber gun in United States naval gun terminology indicates the gun fired a projectile 3 inches (76 mm) in diameter, and the barrel was 50 calibers long. Different guns of this caliber were used by the U.S. Navy and U.S. Coast Guard from 1900 through to 1990 on a variety of combatant and transport ship classes.

<i>Chester</i>-class cruiser Class of American naval ships

The three Chester-class cruisers were the first United States Navy vessels to be designed and designated as fast "scout cruisers" for fleet reconnaissance. They had high speed but little armor or armament. They were authorized in January 1904, ordered in fiscal year 1905, and completed in 1908. In 1920 all scout cruisers were redesignated as "light cruisers" (CL).

<i>Guadiana</i>-class destroyer

The Guadiana class was a class of four destroyers employed by the Portuguese Navy between 1913 and 1942. This class is often alternatively referred as the Douro class.

References

Bibliography

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.