Southall rail crash

Last updated

Southall rail crash
Southall rail crash.jpg
The remains of Coach G of the High Speed Train
Details
Date19 September 1997;26 years ago (1997-09-19)
13:20
Location Southall
CountryEngland
Line Great Western Main Line
Operator Great Western Trains (InterCity 125), Hanson (freight train)
Cause Signal passed at danger
Statistics
Trains2
Passengers212
Deaths7
Injured139
List of rail accidents in the United Kingdom

The Southall rail crash occurred on 19 September 1997, on the Great Western Main Line at Southall, West London. An InterCity 125 high speed passenger train (HST) failed to slow down in response to warning signals and collided with a freight train crossing its path, causing seven deaths and 139 injuries.

Contents

The passenger train operating company had failed to inform Railtrack and the signaller that the automatic warning system (AWS), which warns drivers of adverse signals, had been turned off in the cab of the HST. As a result, the signaller set a route which would stop the HST and allow the freight train to cross in front of it. If the signaller had known that the AWS in the express was not working, he would have been prevented by the operating rules from setting a conflicting route. The HST driver did not apply the brakes until it was too late because he was packing his bag and did not see the cautionary signals. [1] He was charged with manslaughter by gross negligence, but the charges were later dropped.

Great Western Trains, whose managing director survived the crash in one of the most badly affected carriages, was fined for failure to ensure that the HST had their automatic warning system working during long journeys.

Accident

The collision occurred as the 10:32 Great Western Trains (GWT) InterCity 125 HST returned from Swansea toward London Paddington. The train was formed of Class 43 power car 43173, eight Mark 3 carriages, and power car 43163. The driver at the time of the collision, Larry Harrison, boarded the train at Cardiff. [1]

Earlier that day, the HST's previous driver, James Tunnock, had found a fault with the Automatic Warning System (AWS) that prevented the brakes from releasing. In response, he isolated (disabled) the AWS at 06:00 but did not report the failure to the signaller and to Railtrack as was required to enable extra signalling precautions. A fault with the AWS in the London-end power car had also been reported on the previous day, but testing at the OOC Maintenance Depot overnight failed to reveal any fault, and the train was passed for service. [1] :Paragraph 6.26

As the HST approached Southall East Junction, the driver failed to heed two warning signals (a double yellow followed by a single yellow) without slowing the train down, and only reacted by applying the emergency brake when the red danger signal came into view. [2] As the tracks on the Up Main Line straightened ahead of the HST, the driver saw the Hanson-operated Class 59 locomotive 59101 Village of Whatley a mile in the distance, moving "at a funny angle," and realised that it was crossing his path. The freight train, which was formed of 20 empty bogie hopper wagons, was coming from London on the Down Relief line toward the north side, and had been signalled to cross the main lines at Southall East Junction on its way into Southall Yard on the south side. The driver of the freight train, Alan Bricker, observed the approaching HST and expected it to stop, but was alarmed by its speed and apparent brake application. He tried to accelerate his train out of its path of the HST, but to no avail. [1] A collision was now inevitable. The HST was travelling at 125 mph (201 km/h) when the driver saw the danger signal, so even though he applied the emergency brake, the collision occurred at more than 80 mph (130 km/h). [1] [2]

The later accident inquiry report found that:

  1. At 13:20, the front power car of the HST collided with a 22-tonne (22-ton) hopper car.
  2. Two seconds later, coach H collided with a hopper. The HST power car severed the brake pipes of the freight train, causing the stranded rear hopper wagons to stop immediately. A coupling from one of the hoppers was then severed by the derailed and damaged front power car as it passed by, causing debris to land on the track.
  3. Four seconds into the accident, with the HST still travelling at 60 mph (97 km/h), coach H collided with the severed coupling from the freight train, and began to topple away from the freight train onto its left side. It slid on its side for a further four seconds. Two people died in this carriage, falling from the destroyed coach windows and then crushed under the sliding coach H.
  4. Eight seconds into the accident, with both the forward HST power car and coach H clear forward of the scene, coach G—the second coach in the HST formation—hit the now stationary rear of the freight train. The freight wagons were driven back and jackknifed.
  5. Both coach G and the struck hopper wagon lifted into the air. The hopper wagon was restrained in its movement, and collided and jammed up against the nearby overhead line stanchions. The front of coach G was flattened as it slid under the hopper.
  6. Ten seconds into the accident, the rear of the HST, led by coach F, collided with the now stationary coach G. The energy release of the still moving rear of the HST bent the structure of coach G into a distinct half-curve at its midpoint. Five people died in coach G, which was almost completely destroyed.
  7. The rear of the HST, led by coach F, collided with the stationary rear of the freight train. Coach F was left derailed.

Seven passengers died; six at the scene and one in hospital. [1]

The HST driver said he was aware of the isolated AWS but admitted to a lack of focus, referring to putting items in his bag before the incident twice in his tape-recorded conversation with signallers at the nearest trackside telephone:

"I'm okay, yeah, I was just putting me stuff away in the bag the A, the A, the, the AWS has been isolated because some, some brake problem, I believe, so, I had no AWS so, I put me stuff away in the bag and the next thing I knew, I was coming up against red, up, such coming through, through...Through Southall, yeah"... ..."I was just putting me stuff away in the bag, like I would normally do, you see. (signaller: Right.) And all of a sudden I was whizzing through Hayes with a red at Southall (signaller: Right.) I see the slow train crossing over then" [1] :Annex 08

If the AWS or the ATP equipment on the HST had been working, the chance of the accident occurring would have been highly unlikely. Functioning AWS would have given the HST driver an audible warning that he was running towards a signal at danger and needed to start braking. [1] Failure to press the AWS cancelling button to acknowledge the warning would have caused the emergency brake to apply. The train was also fitted with fully operational Automatic Train Protection (ATP) equipment, both at trackside and in the London-end power car, but it was not switched on because neither drivers Harrison nor Tunnock were then qualified to drive with ATP. From 1996, 125 mph (201 km/h) high speed trains were driven by one driver only, following the removal of a requirement for a second driver. [1]

Aftermath

Following this accident and the Ladbroke Grove rail crash, First Great Western (as GWT had become) required all its trains to have ATP switched on. If the equipment is faulty, the train is taken out of service. It emerged after the incident that the reset switch of the warning system had contamination on its electrical contact surfaces which rendered its performance intermittent, hence its disabling at Oxford the day before the crash. [1]

The HST driver and operator were charged with manslaughter, but the charges were later dropped. [3] GWT was fined £1.5 million for not having a system to ensure HSTs were not operated for long journeys with AWS inoperative. [4]

View of the aftermath from a passing train Southall Rail Crash geograph-4012046-by-Ben-Brooksbank.jpg
View of the aftermath from a passing train

The action of the signaller in stopping a high-speed passenger train to allow a slow freight train to cross in front of it has been criticised. However, this is standard procedure when regulating trains to minimise overall delay; there was no reason for the signaller to expect that the HST driver would not stop at the red signal protecting the crossover. At the time there was no requirement for the signaller to have been informed that the HST was in service with its AWS isolated. The Rail Safety and Standards Board rulebook was revised to cover this:

"Driver.....if you become aware that the AWS has become defective when it is required to be in operation, you must.....tell the signaller" [5]

A public inquiry into the incident was formally opened on 24 February 1998, with Professor John Uff appointed to chair by the Health and Safety Commission with the consent of the Secretary of State for Environment, Transport and the Regions. The report was published on 24 February 2000 with 93 recommendations to improve rail safety. [6]

The key point identified in the report was that drivers had become increasingly reliant on AWS with single-manning and high speeds, and that it was no longer acceptable to run trains at full speed if the equipment was inoperative. The rulebook was changed, so that if AWS is isolated the train may only run at high speed with a competent person accompanying the driver in the cab. [5] This person must have full knowledge of the route and know how to stop the train:

"If a competent person is provided....proceed at normal permissible speed to the location where the train can be dealt with. During poor visibility, the train speed must not exceed 40 mph (65 km/h)"

or

"If a competent person is not provided...proceed at a speed not exceeding 40 mph (65 km/h), or any lower permissible speed that may apply, to the location where a competent person is available or to the location where the train can be dealt with" [5]

Among survivors in the two most severely stricken coaches in front of the buffet car were Richard George, then managing director of GWT, who played a valuable role in establishing calm, and four injured members of staff in the buffet car, who quickly organised help for passengers. [1]

After the completion of the inquiry, power car 43173 was scrapped at a remote site, MoD Shoeburyness. As of 2021, power car 43163, which sustained minor damage in the accident, is in service with Abellio ScotRail, having been transferred to the fleet in 2018 among other HSTs.

In 2003, a memorial plaque was unveiled at 51°30′20″N0°22′42″W / 51.5055°N 0.3782°W / 51.5055; -0.3782 .

Related Research Articles

The Ladbroke Grove rail crash was a rail accident which occurred on 5 October 1999 at Ladbroke Grove in London, England, when two passenger trains collided almost head-on after one of them had passed a signal at danger. With 31 people killed and 417 injured, it was one of the worst rail accidents in 20th-century British history.

<span class="mw-page-title-main">InterCity 125</span> British high-speed diesel passenger train

The InterCity 125 (originally Inter-City 125) or High Speed Train (HST) is a diesel-powered high-speed passenger train built by British Rail Engineering Limited between 1975 and 1982. A total of 95 sets were produced, each comprising two Class 43 power cars, one at each end, and a rake of seven or eight Mark 3 coaches. The name is derived from its top operational speed of 125 mph (201 km/h). At times, the sets have been classified as British Rail Classes 253, 254 and 255.

The Train Protection & Warning System (TPWS) is a train protection system used throughout the British passenger main-line railway network, and in Victoria, Australia.

<span class="mw-page-title-main">Signal passed at danger</span> Train passing stop signal without authority

A signal passed at danger (SPAD), known in the United States as a stop signal overrun (SSO) and in Canada as passing a stop signal, is an event on a railway where a train passes a stop signal without authority. This is also known as running a red.

<span class="mw-page-title-main">Automatic Warning System</span>

Automatic Warning System (AWS) is a railway safety system invented and predominantly used in the United Kingdom. It provides a train driver with an audible indication of whether the next signal they are approaching is clear or at caution. Depending on the upcoming signal state, the AWS will either produce a 'horn' sound, or a 'bell' sound. If the train driver fails to acknowledge a warning indication, an emergency brake application is initiated by the AWS. However if the driver correctly acknowledges the warning indication by pressing an acknowledgement button, then a visual 'sunflower' is displayed to the driver, as a reminder of the warning.

<span class="mw-page-title-main">Glenbrook rail accident</span> Australian railway collision

The Glenbrook rail accident occurred on 2 December 1999 at 8:22 am on a curve east of Glenbrook railway station on the CityRail network between Glenbrook and Lapstone, in the Blue Mountains of New South Wales, Australia. Seven passengers were killed and 51 passengers were taken to hospital with injuries when a CityRail electric interurban train collided with the rear wagon of the long-haul Perth-to-Sydney Indian Pacific.

On 8 February 1986, twenty-three people were killed in a collision between a Canadian National Railway freight train and a Via Rail passenger train called the Super Continental, including the engine crews of both trains. It was the deadliest rail disaster in Canada since the Dugald accident of 1947, which had thirty-one fatalities, and was not surpassed until the Lac-Mégantic rail disaster in 2013, which resulted in 47 deaths.

<span class="mw-page-title-main">1967 Thirsk rail crash</span> Train crash in Yorkshire, England on 31 July 1967

The Thirsk rail crash occurred on 31 July 1967 at Thirsk, Yorkshire, England on the British Rail East Coast Main Line.

<span class="mw-page-title-main">Spa Road Junction rail crash</span>

The Spa Road Junction rail crash was an accident on the British railway system which occurred during the peak evening rush hour of 8 January 1999 at Spa Road Junction in Bermondsey, in South East London.

<span class="mw-page-title-main">Zoufftgen train collision</span>

The 2006 Zoufftgen train collision occurred around 11.45 am on 11 October 2006, near Zoufftgen, Moselle, France, some 20 metres from the border with Luxembourg, on the Metz–Luxembourg railway line. Two trains collided head-on while one track of a double track line was out of service for maintenance. Six people, including the drivers of both trains, were killed: two Luxembourgers and four French. Twenty more were injured in the accident, two seriously.

<span class="mw-page-title-main">Wembley Central rail crash</span> 1984 railway accident in London, England

The Wembley Central rail crash was a fatal railway accident that occurred on 11 October 1984 just outside Wembley Central railway station, Greater London.

<span class="mw-page-title-main">1984 Eccles rail crash</span>

The 1984 Eccles rail crash occurred on 4 December 1984 at Eccles, Greater Manchester, when an express passenger train collided at speed with the rear of a freight train of oil tankers. The driver of the express and two passengers were killed, and 68 people were injured. The cause of the accident was determined to be that the driver of the express train had passed a signal at danger.

The Coton Hill rail crash was a train crash which occurred on 11 January 1965, at Coton Hill, near Shrewsbury in Shropshire, England.

The Knowle and Dorridge rail crash was a fatal rail crash that occurred at Dorridge railway station in the West Midlands, England, on 15 August 1963. Three people died in the crash after a signalman's error routed a small freight train into the path of an express passenger train which slowed but could not stop before colliding with it.

<span class="mw-page-title-main">2015 Wootton Bassett rail incident</span> Charter train passed a signal at danger

On 7 March 2015, a steam-hauled charter train passed a signal at danger and subsequently came to a stand across a high-speed mainline junction near Wootton Bassett Junction, Wiltshire, England. Another train, which had right of way, had passed through the junction 44 seconds earlier and no collision occurred nor was any damage done.

On 3 February 2003, a Comeng electric multiple unit train rolled away from Broadmeadows station in Melbourne, Australia, before it ran for nearly 17 kilometres (11 mi) out of control without a driver and eventually crashed into another train about to depart Spencer Street station. Train controllers attempted several times to stop or redirect the train, but were limited in their ability to intervene, instead being forced to alter the route of other trains to avert a more serious collision. Eleven people on board the stationary train were injured; authorities did not know until after the crash if any passengers were on board the runaway. An investigation identified driver error as the cause of the accident, but the runaway event prompted significant debate about the role of government authorities and private operators in ensuring safety and reliability on the Melbourne rail network.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 Professor John Uff QC FREn. "The Southall Rail Accident Inquiry Report" (PDF). HSE Books. Retrieved 7 November 2011.
  2. 1 2 "Seven die as HST ploughs into stone empties". Rail Magazine . No. 315. 8 October 1997. pp. 6–11.
  3. Rail crash manslaughter charges dropped BBC News 2 July 1999
  4. Record fine after Southall crash BBC News 27 July 1999
  5. 1 2 3 "Online Rulebook - Module: TW5 Defective or isolated vehicles and on-train equipment - Section 4.5 (If the AWS is defective or isolated)" (PDF). RSSB. Retrieved 10 June 2016.
  6. "Health and Safety Executive: Southall Rail Accident Inquiry and the Joint Inquiry into Train Protection Systems". The National Archives. Retrieved 6 June 2022.

51°30′23″N0°22′30″W / 51.50639°N 0.37500°W / 51.50639; -0.37500