Alfa Romeo Twin Spark (TS) technology was used for the first time in the Alfa Romeo Grand Prix car in 1914.[1] In the early 1960s it was used in their race cars (GTA, TZ) to enable it to achieve a higher power output from its engines. And in the early and middle 1980s, Alfa Romeo incorporated this technology into their road cars to enhance their performance and to comply with stricter emission controls.
The TS series are all twin cam4-cylinder inline engines. The original 8-valve engine was derived from Alfa's Twin Cam family, and featured a light alloy (silicon enhanced aluminium alloy) block + head, wet-cooled iron cylinder liners, and the camshafts were driven by a single duplex timing chain. So, similar design to the earlier and famous Alfa Romeo Twin Cam engines, but with narrower valve angle and double ignition on this model.
The later 16-valve engines were part of Fiat's "Pratola Serra" (B family) modular engine series,[citation needed] and had a heavier cast-iron block engine, with an alloy head, and the camshafts were belt driven. The Twin Spark name comes from the fact that there are two spark plugs per cylinder. It was cast iron for its higher beam strength, less complexity and hence lower production costs. When new, these engines were notable for their high efficiency as demonstrated by the BMEP (brake mean effective pressures) exerted upon the piston crowns.
The two sparks plugs on the 8V Alfa Twin Spark engines fire at the same time and are symmetrically placed around the vertical line passing through the intake and exhaust valve centers. The flame front travels less distance which allows less ignition advance to be used. Also, leaner mixtures can also be tolerated for better fuel economy. The 8V engine also has 8 identical spark plugs. There is no room for a centrally positioned spark plug due to 2-valve design which uses rather large 44mm diameter inlet valve on the 2.0 engine. On the newer models using the 8V engine the system uses the popular wasted spark system as well. (as also used in Ford EDIS), combining one coil for 2 plugs on opposite phase sister cylinders like 1-4, 2-3 on 4 cylinder engine.
On the Alfa 16V Twin Spark engines one spark plug is ideally located in the centre of the cylinder, as is common in virtually all multi-valve configuration engines. In order to accommodate a second spark plug in the 4-valve combustion chamber, a smaller diameter spark plug is located the very edge of the combustion chamber between an inlet and an exhaust valve. The location of the additional plug means that its impact on maximum performance is marginal. However the engine is able to idle smoothly in very lean conditions (up to 18:1 AFR), this suggests the addition plug is here to improve combustion efficiency under light loads. The next generation Alfa fours, the JTS engines lost the second plugs gained direct injection and increased performance.
The TS 16V engines, 1.6, 1.8 and 2.0, all use a 10mm diameter and a 14mm diameter long life platinum electrode spark plug per cylinder. The spark plugs have a replacement interval of 100,000 kilometres (62,000mi).
16-valve Twin Spark Head.
The 16 Valve engine features individual 'coil over plug' ignition where the timing of the ignition is controlled directly by the Bosch engine management system, with each coil firing two spark plugs simultaneously. On the earlier CF1 and CF2 16 valve engines each coil fired the plug below it and (via a short plug lead) a plug in the other cylinder that was 360° crankshaft rotation out of phase (i.e. one coil would fire a spark plug in the cylinder nearing the top of the compression stroke, and also the a spark plug in the cylinder nearing the top of the exhaust stroke (in a 4-cylinder 4-stroke engine with a 180° crank pistons 1 & 4 and pistons 2 & 3 rise and fall as pairs). So in this configuration each coil services two spark plugs and each cylinder is serviced by two coils. In case of a coil failure one of two plugs would still work.
Ignition systems that fire a plug in a cylinder on its exhaust stroke are referred to as a wasted spark ignition system; as the spark ignites nothing and so is 'wasted'. Wasted spark systems are generally used as a production economy as half the number of coils are required (which consequently have to fire twice as many times), e.g. a four-cylinder four-stroke engine (with a single plug per cylinder) requires only 2 coils alternately firing every 180° of crankshaft rotation, each coil firing every 360° crank rotation to fire all four cylinders. In the 16 Valve Twin Spark 4 coils are required by the eight plugs, so production economy was unlikely to be a factor in the adoption of a wasted spark system.
On the later CF3 (2001 on Euro 3 emissions standard) 16v TS the four coils fire both spark plugs in one cylinder (so not 1 & 4 and 2 & 3 as pairs), and may not be a wasted spark system. The potential benefits of each coil being associated with one cylinder being: halving the firing frequency - the coil is only required to fire every 720° crankshaft rotation rather than every 360° crankshaft rotation. This would double coil saturation time, reducing coil load and improving spark quality at high rpm. Some Bosch engine management system have the ability to advance and retard ignition timing in individual cylinders, which would be impossible in the CF1 and CF2 configurations as each cylinder is serviced by two coils, but could be used in the CF3 setup.
16-valve Twin Spark with older cover.
The engines also incorporate two other devices to enhance the performance under operation, the Camshaft Phase Variator and the Variable Intake Length Control (or Modular Inlet Manifold in Alfaspeak) on the later (plastic cam cover) 1.8- and 2.0-litre versions. Where both these variable systems are deployed they are controlled in tandem by the Bosch Motronic Engine Management ECU in response to rpm, load, and throttle position. According to Fiat Auto S.p.A. DTE electronic service documentation for the 156 Twin Spark (1.8/2.0):
"To optimise the quantity of air drawn into the engine the control unit checks: inlet timing on two angle positions (and) geometry of inlet ducts at two lengths (only 1.8/2.0 TS). At maximum torque speed the control unit sets the "open" phase: cam advanced by 25°, inlet casing long ducts (Only 1.8/2.0 TS). At the maximum power speed the control unit sets the "closed" phase: cam in normal position, inlet box short ducts. At idle speed the control unit sets the "closed" phase: cam in normal position and inlet box short ducts. In the other engine operating conditions, the control unit selects the most suitable configuration to optimise performance - consumption - emissions. During overrunning, the inlet ducts of the box are always short."[2]
The advancing of the inlet camshaft opens and closes the intake valves earlier in the inlet cycle. This allows the filling of the cylinders with air/fuel mix to begin and end earlier when in advanced position thus starting to compress the mix earlier. Or the compression phase to begin later (when in not advanced cam state) by delaying the intake valve closure. The actual compression of the gases can begin only after the closure of the inlet valves so by varying the intake valve closure moment (with the variator) the effective compression ratio can be reduced in not-advanced position. This has benefits as a way to reduce the effective compression ratio but still keep the expansion ratio as before so to lower the compression phase mechanical losses. When the intake valve is also opened earlier in relation to the closing of the exhaust valves, the valve overlap (the period both inlet and exhaust valves are simultaneously open) is also increased at this mode. This promotes the scavenging effect of the exiting exhaust which causes a partial vacuum in the cylinder to further assist in filling the cylinder with a fresh charge. Also this increased overlap, may cause part of the exhaust gases to re-enter in this way make it function like internal EGR.
As with similar inlet cam phasing systems like BMW VANOS the phasing is returned to the retarded state at higher rpm to improve power and efficiency as inlet gas dynamics change with rpm. The short inlet ducts being tuned to the higher frequency and thus shorter inlet duct pressure wave.
On the 16V engines the camshaft variator is used to enhance the performance/emissions but also might be the source to the common 'diesel noise' problem often seen on high mileage used models which used the earlier internals of the variator. The same variator system is also used in many Fiat/Lancia engines like one used in Lancia Kappa 5-cylinder engine, some Fiat Bravo/Fiat Marea engines, Fiat Barchetta, Fiat Coupe, Fiat Stilo etc. models.
Modular Inlet Manifold
The Alfa Romeo Modular Inlet Manifold is a variable intake system fitted to the later CF2 1.8 and 2.0 litre Twin Spark engines.[citation needed] It operates by switching between two separate air intake runners of different lengths (one pair for each cylinder) to either shorten or lengthen the path from the end of the intake runner (within the plenum) to the inlet valves. The system is manifold vacuum-assisted servo-operated, and controlled directly by the Bosch engine management system, as described above. Tuned-length inlet runners operate by using the harmonics created by within the inlet tract/runner by the opening and closing of the inlet valves and flow of gas during the inlet cycle. Each runner is effectively a velocity stack which reflects a positive pressure wave back down the inlet runner to maximise cylinder filling with fuel/air mix. The rpm band over which the pressure wave arrives at the open inlet valves and is able to assist in the cylinder filling is set by the length of the runner and is a relatively narrow. Swapping between runners of differing length broadens the rpm band over which benefits of the tuned inlet runners are achieved, leading to a flatter torque curve and consequently more power across the rev range.
In addition air-flow within the stock intake tubing between the throttle plate and airbox has also been maximised. This includes an 'inlet trumpet' at the end of the intake pipe within the airbox (often referred to as the "cone" by Alfisti) which is designed to improve airflow and fuel metering by reducing turbulence, (and may reflect positive pressure waves back down the intake tube). There is much discussion on about improving performance by removing the trumpet or 'de-coning' as it is often referred to,[citation needed] as the trumpet is thought by some to restrict air flow due to its small inlet cross-section. While "de-coning" results improvement in inlet cross-section any benefit is likely to be off set by the 'pinch effect' of an unradiused inlet, which is 0.6 - 0.5 the efficiency of a trumpet radius on the same diameter inlet[3]
Variable valve timing
Variable valve timing gave the Twin Spark engine very good performance for its cubic capacity, but it is one of the weaker areas of the 16-valve engine. The original variator that controls the cam timing is prone to wear or jam, although replacement part carries a different part number and has improved reliability. Symptoms are a slight loss of performance and a diesel type rattle from the top of the engine, which appears at startup and gradually lasts for longer.[4] It is therefore advisable to get the variator changed regardless of its apparent condition at the 36,000 mile (60,000km) cambelt replacement. The variator problem is not often seen in the earlier 8V Twin Spark version, as these use a different type of cam timing variator system, this is also the case for later 16v versions used in the Alfa Romeo 156 and the 147 where the weak variator was addressed.
Variable valve timing (VVT) is the process of altering the timing of a valve lift event in an internal combustion engine, and is often used to improve performance, fuel economy or emissions. It is increasingly being used in combination with variable valve lift systems. There are many ways in which this can be achieved, ranging from mechanical devices to electro-hydraulic and camless systems. Increasingly strict emissions regulations are causing many automotive manufacturers to use VVT systems.
The GM Ecotec engine, also known by its codename L850, is a family of all-aluminium inline-four engines, displacing between 1.4 and 2.5 litres. Confusingly, the Ecotec name was also applied to both the Buick V6 Engine when used in Holden Vehicles, as well as the final DOHC derivatives of the previous GM Family II engine; the architecture was substantially re-engineered for this new Ecotec application produced since 2000. This engine family replaced the GM Family II engine, the GM 122 engine, the Saab H engine, and the Quad 4 engine. It is manufactured in multiple locations, to include Spring Hill Manufacturing, in Spring Hill, Tennessee, with engine blocks and cylinder heads cast at Saginaw Metal Casting Operations in Saginaw, Michigan.
A W8 engine is an eight-cylinder piston engine with four banks of two cylinders each, arranged in a W configuration.
The GM High Feature engine is a family of modern DOHC V6 engines produced by General Motors. The series was introduced in 2004 with the Cadillac CTS and the Holden Commodore (VZ).
In automotive engineering a multi-valve or multivalve engine is one where each cylinder has more than two valves. A multi-valve engine has better breathing and may be able to operate at higher revolutions per minute (RPM) than a two-valve engine, delivering more power.
A wasted spark system is a type of ignition system used in some four-stroke cycle internal combustion engines. In a wasted spark system, the spark plugs fire in pairs, with one plug in a cylinder on its compression stroke and the other plug in a cylinder on its exhaust stroke. The extra spark during the exhaust stroke has no effect and is thus "wasted". This design halves the number of components necessary in a typical ignition system, while the extra spark, against much reduced dielectric resistance, barely impacts the lifespan of modern ignition components. In a typical engine, it requires only about 2–3 kV to fire the cylinder on its exhaust stroke. The remaining coil energy is available to fire the spark plug in the cylinder on its compression stroke.
The Lamborghini V10 is a ninety degree (90°) V10 petrol engine which was developed for the Lamborghini Gallardo automobile, first sold in 2003.
The Toyota JZ engine family is a series of inline-6 automobile engines produced by Toyota Motor Corporation. As a replacement for the M-series inline-6 engines, the JZ engines were 24-valve DOHC engines in 2.5- and 3.0-litre versions.
The Toyota S Series engines are a family of straight-four petrol engines with displacements between 1.8 and 2.2 litres, produced by Toyota Motor Corporation from January 1980 to August 2007. The S series has cast iron engine blocks and aluminium cylinder heads.
The Toyota E engine family is a straight-four piston engine series, and uses timing belts rather than chains. The E engines were the first multi-valve engines from Toyota designed with economy, practicality and everyday use in mind. Like many other Toyota engines from the era, the E engine series features a cast iron block, along with an aluminium cylinder head. E engines are lighter than earlier Toyota engines, due to the hollow crankshaft, thinned casting of the cylinder block, and several other reductions in auxiliaries as well as in the engine itself. Carbureted versions include a newly designed, variable-venturi carburetor. All of these changes improved economy and emissions. The members of the E engine family, range from 1.0 L to 1.5 L. The E family supplanted the K engines in most applications. A large number of parts in the E engine series are interchangeable between each other.
The Alfa Romeo Twin Cam engine is an all-alloy inline-four engine series produced by Alfa Romeo from 1954 to 1994. In Italian it is known as the "bialbero" ("twin-shaft"), and has also been nicknamed the "Nord" (North) engine in reference to its being built in Portello, Milan, in the North of Italy and to distinguish it from the Alfa Romeo Boxer engine built in the South (Sud) for the Alfasud.
The JTS engine is a gasoline direct injection engine produced by Alfa Romeo. It exists in two forms, straight-4 and V6, and was introduced into the Alfa lineup in 2002.
The Subaru EJ engine is a series of four-stroke automotive engines manufactured by Subaru. They were introduced in 1989, intended to succeed the previous Subaru EA engine. The EJ series was the mainstay of Subaru's engine line, with all engines of this series being 16-valve horizontal flat-fours, with configurations available for single, or double-overhead camshaft arrangements. Naturally aspirated and turbocharged versions are available, ranging from 96 to 310 hp. These engines are commonly used in light aircraft, kit cars and engine swaps into air-cooled Volkswagens, and are also popular as a swap into copy wasserboxer engined Volkswagen T3/Vanagon. Primary engineering on the EJ series was done by Masayuki Kodama, Takemasa Yamada and Shuji Sawafuji of Fuji Heavy Industries, Subaru's parent company.
Variable valve timing (VVT) is a system for varying the valve opening of an internal combustion engine. This allows the engine to deliver high power, but also to work tractably and efficiently at low power. There are many systems for VVT, which involve changing either the relative timing, duration or opening of the engine's inlet and exhaust valves.
The Ferrari flat-12 engine family is a series of flat-12 DOHC petrol engines produced by Ferrari from 1964 to 1996. The first racing Ferrari flat-12, the Mauro Forghieri-designed Tipo 207, was introduced in the Ferrari 1512 F1 car in 1964. Later flat-12 racing engines were used in Ferrari Formula One and sports racing cars from 1968 until 1980, including the 212 E Montagna, 312 B series, 312 PB and 312 T series. The roadgoing flat-12 engines were introduced with the 365 GT4 BB and were produced in various versions until the end of F512M production in 1996.
The Fiat Pratola Serra modular engines are a family of engines produced by the Fiat Group since 1994 and used in Fiat, Alfa Romeo, Lancia and Jeep vehicles. They are named after the Pratola Serra municipality in which they're being produced.
The Volkswagen-Audi V8 engine family is a series of mechanically similar, gasoline-powered and diesel-powered, V-8, internal combustion piston engines, developed and produced by the Volkswagen Group, in partnership with Audi, since 1988. They have been used in various Volkswagen Group models, and by numerous Volkswagen-owned companies. The first spark-ignition gasoline V-8 engine configuration was used in the 1988 Audi V8 model; and the first compression-ignition diesel V8 engine configuration was used in the 1999 Audi A8 3.3 TDI Quattro. The V8 gasoline and diesel engines have been used in most Audi, Volkswagen, Porsche, Bentley, and Lamborghini models ever since. The larger-displacement diesel V8 engine configuration has also been used in various Scania commercial vehicles; such as in trucks, buses, and marine (boat) applications.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
