The Alfa Romeo 75 (Type 161, 162B), sold in North America as the Milano, is a compact executive car produced by the Italian automaker Alfa Romeo between 1985 and 1992. The 75 was commercially quite successful: in only three years, 236,907 cars were produced,[3] and by the end of production in 1992, around 386,767 had been built.[4]
The 75 was the last model released before Alfa Romeo was acquired by Fiat. (The Alfa Romeo 164 was the last model developed independently.)
Overview
The 75 was introduced in May 1985[5] to replace the Giulietta (with which it shared many components), and was named to celebrate Alfa Romeo's 75th anniversary. The body, designed by head of Centro Stile Alfa Romeo Ermanno Cressoni, was styled in a striking wedge shape, tapering at the front with square headlights and a matching grille (similar features were applied to the Cressoni-designed 33).
At the 1986 Turin Auto Show, a prototype of an estate bodystyle of the 75 was presented, an attractive forerunner of the later 156 Sportwagon. This version was, however, never put into production, being cancelled after Fiat took control of Alfa Romeo. The car, dubbed the 75 Turbo Wagon, was made by Italian coachbuilder Rayton Fissore using a 75 Turbo as the basis.[6] However, two estate concept models were unveiled 1987 Geneva Motor Show; one was the Turbo Wagon and the other was a 2.0-litre version named the Sportwagon.[7]
Technical features
Alfa Romeo 75 Twin Spark 2.0 LUS-market Milano Quadrifoglio Verde, with the 3-litre V6
The 75 featured some unusual technical features, most notably the fact that it was almost perfectly balanced from front to rear.[8] This was achieved by using a transaxle configuration — mounting a standard five-speed gearbox and clutch at the rear, integrated with the rear differential. The front suspension design is a torsion bar and shock absorber combination and the rear an expensive de Dion tube assembled with shock absorbers; these designs were intended to optimise the car's handling; moreover, the rear brake discs were fitted at the centre of the rear axle, near the gearbox-differential group. The engine's crankshaft is bolted directly to the two-segment driveshaft, which runs the length of the underside of the car, from the engine block to the gearbox, and rotates at the speed of the engine. The shaft segments are joined with elastomeric 'doughnuts' to prevent vibration and engine/gearbox damage. The 2.0 litre Twin Spark and the 3.0 litre V6 are equipped with a limited slip differential.[9]
The 75 featured a then-advanced dashboard-mounted diagnostic computer, called Alfa Romeo Control, capable of monitoring the engine systems and alerting drivers of potential faults.
The 75's engine range at launch featured four-cylinder 1.6, 1.8 and 2.0 litre petrol carbureted engines, a 2.0 litre intercooled turbodiesel engine made by VM Motori,[10] and a 2.5 litre fuel injected V6 engine. The 75 Turbo was introduced in 1986, which featured a fuel-injected 1.8 litre twin-cam engine using aGarrett T3 turbocharger, intercooler and oil cooler.[11]
Post facelift modelInterior (V6 Milano model)
In 1987, a 3.0 litre V6 was added to the range and the 2.0 litre Alfa Romeo Twin Cam engine was redesigned to have now two spark plugs per cylinder, which engine was named "Twin Spark". With fuel injection and variable valve timing, this engine produced 148PS (109kW; 146hp). This was an early example of a production engine using variable valve timing, though the first to do so was Alfa Romeo's own Spider in 1980. In North America, where the car was known as the Milano, only the 2.5 and 3.0 litre V6 engines were available, from 1987 to 1989.
The North American 2.5 litre engines were fundamentally different from their European counterparts. Due to federal regulations, some modifications were required. Most noticeable from the outside were the 'America' bumpers, with the typical rubber accordion like extensions in them. Furthermore, these bumpers had thick (and heavy) shock-absorbing material inside, and in addition, they were mounted to the vehicle on shock absorbers. To accommodate these shock absorbers, the 'America'-bodies were slightly different from the European ones. Other changes relative to the European model were:
A 67-litre fuel tank which was located behind the rear seats, reducing the boot capacity from 500L (18cuft) to 300L (11cuft).
Side-markers in the bumpers
Exhaust silencer sticking out from under the bumper on the right side of the vehicle instead of at the centre
Reinforcements in the doors (side impact bar) and boot lid
Hooks underneath the bonnet (engine hood), to keep the bonnet in position in a crash
The North American cars also had optional levels of equipment (depending on the version: Milano Silver, Gold, Platinum, or Verde). L/h and r/h electrically adjustable outside mirrors, electrically reclining seats and cruise control were usually optional in Europe. The car was also available with a 3-speed ZF automatic gearbox option for the 2.5-litre V6. Other, more common options such as electrically operated rear windows and an A/C system were standard in the USA. The US market cars also had different upholstery styles and different dashboard instrumentation indicating speed in mph, oil pressure in psi and coolant temperature in degrees F, and as a final touch, the AR control was different, and included a seat belt warning light. Some North American specification Milanos were also sold in Switzerland (When catalytic converters were made mandatory in 1987).
The European-spec 2.5 V6 (2.5 6V Iniezione or 2.5QV) was officially sold only between 1985 and 1987, although some of them were not registered until 1989. Relatively few of them were sold (about 2,800 units), especially when the 155PS (114kW; 153hp) 1.8 Turbo was launched, which in some countries was cheaper for taxation reasons because of its lower displacement. To better differentiate between the V6 and the inline fours, the 2.5-litre engine was bored out to 2,959 cc's to deliver 188PS (138kW; 185hp) and this new engine was introduced as the 3.0 America in 1987. As its type designation suggests, the 3.0 only came in the US-specification, with the impact-bumpers and in-boot fuel tank. However, the European 'Americas' were not equipped with side-markers or the door, bonnet and boot lid reinforcements. Depending on the country of delivery, the 3.0 America might be equipped with a catalytic converter.
In 1988, engines were updated again, the carbureted version of the 1.8-litre engine was replaced with a fuel injected variant and a new and bigger diesel engine was added to the range. At the end of 1989, the carbureted version of the 1.6-litre engine was updated to have fuel injection and in 1990 the 1.8-litre turbo and 3.0-litre V6 got some more power and updated suspension. The 3.0 V6 was now equipped with a Motronic digital fuel injection system instead of the previous analog electronic L-Jetronic injection system. The 1.8L turbo was now also available in 'America'-spec, but strangely enough, was not available in the USA market. The 3.0 V6 did make it to the United States and was sold as the Milano Verde.[11]
Model
Units produced
1.6
99,522
1.6 IE
27,989
1.8
45,138
1.8 IE
48,270
1.8 Turbo/America/Q.V.
6,536
2.0
18,971
2.0 Twin Spark
57,084
2.5 6v Q.V/Milano
12,611
3.0 V6/America/Q.V./
6,753
2.0 TD
46,273
2.4 TD
6,110
Total
375,257
Turbo Evoluzione
Alfa Romeo 75 Turbo Evoluzione
500 examples of the Turbo Evoluzione were produced in the spring of 1987 to meet Group A requirements as a more potent variant of the 75 turbo to homologate aerodynamic changes to the racing model.[12] The car had many modifications when compared to the standard turbo model. The engine was de-bored from 80 mm to 79.6 mm in order to have a capcity of 1,762cc (normally 1,779cc) in order to prevent the race entry from competing in the Class 1 category where it would be highly disadvantageous against the competition. While the claimed power was the same as in the standard turbo, the thicker cylinder walls made the engine better suited to power upgrades than was the standard 75 Turbo engine in competition trim. All 500 cars were left hand drive and a large number of them were sold in the home market of Italy[13][14]
Replacing the previous 3.0 L, this engine from the 164 featured Motronic fuel injection rather than the earlier L-Jetronic. This model was known as the "Potenziata."
Alfa Romeo and its racing department Alfa Corse raced the 75 Turbo Group A in the World Touring Car Championship in the 1987 season. There were six official entries, two were run directly by Alfa Corse, two by Brixia Corse, one by Albatech, and one by the Swedish team Q-Racing. Team drivers included Formula One veterans such as Nicola Larini, Gabriele Tarquini, Alessandro Nannini, Jacques Laffite, and Mario Andretti as well as World Sportscar champion Jean-Louis Schlesser.[15] The Class 2 car had enough power (approximately 320bhp (239kW; 324PS)) to be on par with the new and more track focused BMW M3. However, Alfa Romeo had very little success in the WTCC and with the whole season descending into a political farce, Alfa Romeo team boss Cesare Fiorio withdrew the team before the overseas races.[16]
Australian driver Colin Bond, winner of the 1975Australian Touring Car Championship and 1969 Hardie-Ferodo 500, had been racing the GTV6 since 1984. Remaining loyal to Alfa Romeo, he ran a Caltex sponsored Alfa 75 in the 1987 Australian Touring Car Championship, replacing the GTV6. Bond's new 75 was built by the Italian Luigi team, but Bond found that the engine produced about 200bhp (149kW; 203PS) rather than the promised 320bhp (239kW; 324PS). This saw him finish in a distant 9th place in the championship while the team's engine builder, Melbourne based Alfa expert tuner Joe Beninca, tried to reclaim the lost 120bhp (89kW; 122PS). This was finally achieved by converting the car to right hand drive, allowing for an exhaust system that did not wind around the steering rack. Bond also drove the end of season endurance races including the Bathurst race of the WTCC. After Bond qualified in 21st, co-driver Lucio Cesario destroyed the front of the 75 in a crash at the top of the mountain on lap 34 of the race, forcing the car's withdrawal from the Calder Park and Wellington races of the WTCC. The car was repaired in time for the Australian Grand Prix support races in Adelaide where Bond qualified for a second place start and finished 5th in the car's "down under" swansong. Bond was the only driver to embrace the 75 in Australia but switched to race the all-conquering Ford Sierra RS500 starting in 1988 in a bid to return to the winners circle.
The British Alfa Romeo Dealer Team ran a pair of cars in the 1986–87 seasons with drivers Rob Kirby and John Dooley. Racing in Class B, the team started with the V6 version of the 75, alongside their older GTV6, before upgrading to the 75 turbo. They were able to match the pace of the Ford Escort RS turbos but once Frank Sytner's BMW M3 appeared, they were rendered uncompetitive.[citation needed]
Related Research Articles
The V6 PRV engine is an overhead cam V6 automobile engine designed and manufactured by the company "Française de Mécanique" for PRV, an alliance of Peugeot, Renault and Volvo Cars. Sold from 1974 to 1998, it was produced in four displacements between 2.5 L and 3.0, and in both SOHC and DOHC and 2-valve and 4-valve per cylinder configurations. Originally carbureted, it adopted fuel-injection for improved emissions compliance and improved performance, and was offered in turbo and biturbo versions in a limited number of vehicles made by Renault, Chrysler Motors, and French supercar manufacturer Venturi.
The SEAT León, also spelled Leon in some other languages, is a small family car built by the Spanish car manufacturer SEAT since October 1999.
The Audi 80 is a compact executive car produced by the Audi subdivision of the Volkswagen Group across four generations from 1966 to 1996. It shared its platform with the Volkswagen Passat from 1973 to 1986 and was available as a saloon, and station wagon — the latter marketed by Audi as the Avant. The coupé and convertible models were not badged as members of the range, but used a derivative of the same platforms.
The Alfa Romeo 156 is a compact executive car produced by the Italian automobile manufacturer Alfa Romeo. It was introduced at the 1997 Frankfurt Motor Show as the replacement for the Alfa Romeo 155. The 156 received a positive reception and in the following year went on to win the 1998 European Car of the Year award. The 156 saloon was discontinued in Europe late in 2005, while the Q4 Crosswagon continued in production until the end of 2007.
The Alfa Romeo 33 is a small family car produced by the Italian automaker Alfa Romeo between 1983 and 1995. From a mechanical standpoint it was essentially an evolution of its predecessor, the Alfasud, whose floorpan, chassis and drivetrain were carried over — albeit with simplifications to the suspension and braking system, eschewing the Alfasud's inboard front brakes for instance. The Nissan-based Alfa Romeo Arna was launched shortly thereafter, offering a similarly sized but lower priced car.
The Alfa Romeo 164 is a four-door executive saloon manufactured and marketed by Italian automaker Alfa Romeo from 1987 to 1998, styled by Pininfarina, and cooperatively designed and sharing platforms and numerous elements with the Fiat Croma, Saab 9000 and Lancia Thema.
The Alfa Romeo 155 is a compact executive car produced by Italian automobile manufacturer Alfa Romeo between 1992 and 1998. It was unveiled in January 1992 at Barcelona, with the first public launch in March 1992, at the Geneva Motor Show. A total of 195,526 units were made before it was replaced by the 156.
The Ferrari Dino engine is a line of mechanically similar V6 and V8 engines produced by Ferrari for about 40 years from the late 1950s into the early 2000s.
The Alfa Romeo 159 is a car built by Italian marque Alfa Romeo between 2004 and 2011. It is a large family car in the compact-executive market segment with four-door saloon and five-door estate variants. Introduced at the 2005 Geneva Motor Show, as a replacement for the 156, the 159 used the GM/Fiat Premium platform, shared with the Alfa Romeo Brera and Spider as well as the Kamal and Visconti concept cars.
The Peugeot 605 is an executive car produced by the French manufacturer Peugeot between 1989 and 1999, with a facelift in 1995.
The Alfa Romeo GTV and the Alfa Romeo Spider are sports cars produced by the Italian automobile manufacturer Alfa Romeo from 1993 to 2004. The GTV is a 2+2 coupé, while the Spider is a two-seater roadster. Production totaled 38,891 units for the Spider and 42,937 units for the GTV.
The Alfa Romeo 166 is an executive car produced by the Italian automaker Alfa Romeo, between 1996 and June 2007. The car was designed by Centro Stile Alfa Romeo, under the control of Walter de Silva, and was facelifted in September 2003.
The Alfa Romeo Alfasud Sprint is a boxer-engined coupé produced by the Italian manufacturer Alfa Romeo from 1976 to 1989, and based on the Alfa Romeo Alfasud. 116,552 units of the Alfasud Sprint and Sprint were built in total. The Sprint was sold in Europe, South Africa, Australia, and New Zealand.
The Alfa Romeo Alfa 6 is an executive car produced by the Italian automaker Alfa Romeo from 1979 to 1986. Its name refers to the six cylinders of the Alfa Romeo V6 engine, which made its first appearance on this car.
The Alfa Romeo 90 is an executive car produced by Italian car manufacturer Alfa Romeo between 1984 and 1987.
The Alfa Romeo Alfetta is a front-engine, five-passenger saloon and fastback coupé manufactured and marketed by Italian automaker Alfa Romeo from 1972 to 1987 with a total over 400,000 units produced during its production run.
The Alfa Romeo Twin Cam engine is an all-alloy inline-four engine series produced by Alfa Romeo from 1954 to 1994. In Italian it is known as the "bialbero" ("twin-shaft"), and has also been nicknamed the "Nord" (North) engine in reference to its being built in Portello, Milan, in the North of Italy and to distinguish it from the Alfa Romeo Boxer engine built in the South (Sud) for the Alfasud.
The Alfa Romeo V6 engine is a 60° V6 engine made by Alfa Romeo from 1979 to 2005. It was developed in the early 1970s by Giuseppe Busso, and first used on the Alfa 6 with a displacement of 2.5 L (2,492 cc) and a SOHC 12-valve cylinder head. Later versions ranged from 1,996 to 3,179 cc and had DOHC 24-valve valvetrains. The original design had short pushrods for the exhaust valves in a design similar to earlier Lancia Fulvia engines. The first DOHC version was in the 1993 Alfa Romeo 164, with an aluminium alloy engine block and head with sodium filled exhaust valves.
The Alfa Romeo MiTo is a front-wheel drive, three-door supermini designed by Centro Stile Alfa Romeo and presented in 2008 at Castello Sforzesco in Milan with an international introduction at the British Motor Show in 2008. The MiTo was marketed across a single generation from 2008 to 2018, sharing the Fiat Small platform with the Fiat Grande Punto. Production reached 293,428 at FCA's Mirafiori plant.
Colin Bond Racing was an Australian motor racing team that competed in the Australian Touring Car Championship between 1984 and 1993.
References
↑ "Designer". ajovalo.net. Retrieved 8 February 2012.
1 2 "Alfa Romeo 75". carsfromitaly.net. Archived from the original on 31 July 2007. Retrieved 7 August 2007.
↑ "The 75". www.alfaromeo75.it (in Italian). Retrieved 4 August 2007.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
