Saturn I4 engine

Saturn engine
Saturn engine
Overview
Manufacturer	Saturn Corporation
Also called	Single Cam; Twin Cam;
Layout
Configuration	Straight-4
Displacement	1.9 L; 116.0 cu in (1,901 cc)
Cylinder bore	82 mm (3.23 in)
Piston stroke	90 mm (3.54 in)
Cylinder block material	Aluminum
Cylinder head material	Aluminum
Valvetrain	SOHC 2 valves x cyl.; DOHC 4 valves x cyl. ;
Compression ratio	SOHC: 9.3:1; DOHC: 9.5:1;
Combustion
Fuel system	Throttle-body fuel injection ; Sequential MPFI ;
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	LK0: 85 hp (63 kW); L24: 100 hp (75 kW); LL0: 124 hp (92 kW);
Specific power	LK0: 44.7 hp (33.3 kW)/L; L24: 52.6 hp (39.2 kW)/L; LL0: 65.2 hp (48.6 kW)/L;
Torque output	LK0: 107 lb⋅ft (145 N⋅m); L24: 115 lb⋅ft (156 N⋅m); LL0: 122 lb⋅ft (165 N⋅m);
Dimensions
Dry weight	SOHC: 196.74 lb (89.24 kg); DOHC: 220.22 lb (99.89 kg);
Chronology
Successor	Ecotec engine (de facto)

Last updated February 28, 2024

The powerplant used in Saturn S-Series automobiles was a straight-4 aluminum piston engine produced by Saturn, a subsidiary of General Motors. The engine was only used in the Saturn S-series line of vehicles (SL, SC, SW) from 1991 through 2002. It was available in chain-driven SOHC or DOHC variants.

Engine block

The engine utilized a water-cooled aluminum block. The main bearing caps were made of ductile iron and held in place with two bolts each. The cylinder block bores had interference fit cast iron liners for the piston rings to sit against. The engine block was made from 319.1 aluminum alloy and the liners were made from grey iron.

Crankshaft

The crankshaft was supported by five main bearings with thrust taken at the middle bearing. 1991 and 1992 engines had a different crankshaft from 1993 and later engines, whose crankshafts had reluctor ring slots advanced ten degrees for easier starting. 1991 to 1998 crankshafts incorporated four counterweights, while those from 1999 to 2002 incorporated eight.

Connecting rods and pistons

From 1991 to 1998 the connecting rods were forged steel with standard type crank pin bearings. SOHC engines during that period used a dished piston design whereas the twin cam engines used a flat top piston with 2 recesses for the intake valves. Twin cam pistons received several re-designs throughout the production run aimed at reducing oil consumption issues. These included reducing the clearance between the top of the piston and the first compression ring, redesigning the skirts on the pistons and the oiling ports on the bottom of the pistons. For the 1999 model year all pistons were totally redesigned. Both engines used the flat top pistons with 2 valve recesses and featured a new hypereutectic design with coated skirts. Also for 1999 all connecting rods switched to a slightly longer powder forged design and cracked bearing caps. The piston pins floated in the connecting rod bushings. The pistons were cast aluminum alloy with the piston pins being retained with snap rings.

Timing chain

The timing chain was hydraulic tensioned and had a ratchet mechanism to keep the chain tight. The timing chain rode on one pivoting chain guide resting on the ratchet tensioner and one fixed guide attached to the engine block and cylinder head. The 1991 to 1998 DOHC engine had an upper timing chain guide in between the camshaft sprockets. The timing chain was lubricated via cast-off from the top of the cylinder head and one 'squirter' on the oil pump housing. The SOHC, 1991-1998 DOHC, and 1999-2002 DOHC engines all used different timing chain sets.

SOHC LK0/L24

The SOHC (LK0/L24) cylinder head had 8 valves and was made of lost foam cast aluminum. The camshaft was located in the center of the cylinder head and driven by a chain off the front crankshaft sprocket. Motion from the camshaft was transmitted to the eight valves by the hydraulic lifters and rocker arms.

The SOHC engine was used in the base model S-series vehicles (SC1, SL, SL1, SW1)

The LK0 engine first used TBI (Throttle Body Injection) for fuel delivery and was rated at 85 hp (63 kW) at 5000 rpm and 107 lb⋅ft (145 N⋅m) at 2400 rpm from 1991 to 1994.^[1]

The L24 engine received MPFI (Multi-Port Fuel Injection) in 1995 which increased power output to 100 hp (75 kW) at 5000 rpm and 115 lb⋅ft (156 N⋅m) at 2400 rpm. In 1999, these engines switched from the recessed top pistons of the previous models to all new flat top pistons that were also used in the twin cam models. The cylinder head was also redesigned to keep the compression ratio at 8.8:1 even with the flat top pistons and now featured provisions for an air injection reaction system. This engine was used from 1995 to 2002.^[2]

Some 1992 through 1998 L24 cylinder heads developed cracks in the fifth camshaft journal, located closest to #4 cylinder. The hairline crack would form between the oil feed port of that journal and the coolant passages in the cylinder head. Symptoms would range from overheating to low coolant, however, most cars affected by this issue exhibited oil migration into the cooling system. The resulting mixture of the two fluids would result in a thick brown "milkshake"-like mixture, visible in the coolant overflow tank.

Saturn released unadvertised policy which would cover this issue, extending the warranty on the cylinder head to 6 years or 100,000 miles (160,000 km). Repair required the replacement of the cylinder head. and flushing of the coolant system. Badly affected cars would see coolant in the oil, as well as oil in the coolant, and would require the replacement of the complete engine assembly. Until the cylinder head casting was redesigned some time in 1998, some vehicles would require this repair more than once, and replacement cylinder heads could develop the same crack.

It was estimated that between 2% and 5% of SOHC Saturn S-Series vehicles were affected by this defect. DOHC engines had a different cylinder head, and did not suffer the same issue.

DOHC LL0

The 1991-1998 DOHC cylinder head had 16 valves and was made of lost foam cast aluminium. The camshafts were held in the cylinder head with bearing caps and driven by a chain off the front crankshaft sprocket. Motion from the camshafts was transmitted to the 16 valves by direct-acting hydraulic lifters.

LL0 cylinder heads were changed slightly in 1995, when Saturn adopted electronic, linear EGR mechanisms, over the previous vacuum actuated design. The head casting was changed to accommodate different mounting surface of the new valve. (1994 CA emissions engines used an adapter to mount the LEGR valve.)

A new LL0 cylinder head appeared in 1999 using a roller camshaft with hydraulic lifters and rocker arms, but power was unchanged. Also for 1999 provisions for a new air injection reaction system was introduced aimed at improving engine emissions.

All LL0 engines used MPFI and were rated at 124 hp (92 kW) at 6000 rpm^[3] and 122 lb⋅ft (165 N⋅m) at 4800 rpm.^[4] The DOHC engine was used in the upper-level model S-series vehicles (SC, SC2, SL2, SW2).

Gallery

LK0/L24 head
Crankshafts
1991-1998 connecting rod

Related Research Articles

<span class="mw-page-title-main">Camshaft</span> Mechanical component that converts rotational motion to reciprocal motion

A camshaft is a shaft that contains a row of pointed cams, in order to convert rotational motion to reciprocating motion. Camshafts are used in piston engines, mechanically controlled ignition systems and early electric motor speed controllers.

The GM Ecotec engine, also known by its codename L850, is a family of all-aluminium inline-four engines, displacing between 1.4 and 2.5 litres. Confusingly, the Ecotec name was also applied to both the Buick V6 Engine when used in Holden Vehicles, as well as the final DOHC derivatives of the previous GM Family II engine; the architecture was substantially re-engineered for this new Ecotec application produced since 2000. This engine family replaced the GM Family II engine, the GM 122 engine, the Saab H engine, and the Quad 4 engine. It is manufactured in multiple locations, to include Spring Hill Manufacturing, in Spring Hill, Tennessee, with engine blocks and cylinder heads cast at Saginaw Metal Casting Operations in Saginaw, Michigan.

The Northstar engine is a family of high-performance 90° V engines produced by General Motors between 1993 and 2011. Regarded as GM's most technically complex engine, the original double overhead cam, four valve per cylinder, aluminum block/aluminum head V8 design was developed by Oldsmobile R&D, but is most associated with Cadillac's Northstar series.

The LA engines are a family of pushrod OHV small-block 90° V-configured gasoline engines built by Chrysler Corporation. They were factory-installed in passenger vehicles, trucks and vans, commercial vehicles, marine and industrial applications from 1964 through 2003. Their combustion chambers are wedge-shaped, rather than polyspherical, as in the predecessor A engine, or hemispherical in the Hemi. LA engines have the same 4.46 in (113 mm) bore spacing as the A engines.

The Chrysler 1.8, 2.0, and 2.4 are inline-4 engines designed originally for the Dodge and Plymouth Neon compact car. These engines were loosely based on their predecessors, the Chrysler 2.2 & 2.5 engine, sharing the same 87.5 mm (3.44 in) bore. The engine was developed by Chrysler with input from the Chrysler-Lamborghini team that developed the Chrysler/Lamborghini Formula 1 V12 engine in the early 1990s.

<span class="mw-page-title-main">Ford Modular engine</span> Engine family produced by Ford Motor Company

The Ford Modular engine is Ford Motor Company's overhead camshaft (OHC) V8 and V10 gasoline-powered small block engine family. Introduced in 1990, the engine family received its “modular” designation by Ford for its new approach to the setup of tooling and casting stations in the Windsor and Romeo engine manufacturing plants.

The Mazda B-series engine - not to be confused with the Mazda B-Series truck - is a small-sized, iron-block, inline four-cylinder with belt-driven SOHC and DOHC valvetrain ranging in displacement from 1.1 to 1.8 litres. It was used from front-wheel drive economy applications to the turbocharged full-time 4WD 323 GTX and rear-wheel drive Miata as well as numerous other models. The Mazda B-series is a "non-interference" design, meaning that breakage of its timing belt does not result in damage to valves or pistons, because the opening of the valves, the depth of the combustion chamber and the shaping of the piston crown allow sufficient clearance for the open valves in any possible piston position.

<span class="mw-page-title-main">Nissan KA engine</span> Reciprocating internal combustion engine

The KA engines were a series of four-stroke inline-four gasoline piston engines manufactured by Nissan, which were offered in 2.0 and 2.4 L. The engines blocks were made of cast-iron, while the cylinder heads were made of aluminum.

The Mitsubishi Sirius or 4G6/4D6 engine is the name of one of Mitsubishi Motors' four series of inline-four automobile engines, along with Astron, Orion, and Saturn.

Honda's first production V6 was the C series; it was produced in displacements from 2.0 to 3.5 liters. The C engine was produced in various forms for over 20 years (1985–2005), having first been used in the KA series Legend model, and its British sister car the Rover 800-series.

The Hyundai Beta engines are 1.6 L to 2.0 L I4 built in Ulsan, South Korea.

The Honda F-Series engine was considered Honda's "big block" SOHC inline four, though lower production DOHC versions of the F-series were built. It features a solid iron or aluminum open deck cast iron sleeved block and aluminum/magnesium cylinder head.

The Volvo B21 is a slanted straight-four engine first used in the Volvo 200 series, meant to replace the B20. The B21 and all derived engines are often referred to as red block engines for the red paint applied to the block. The primary differences when compared to the B20 was the switch to a SOHC in place of the older pushrod configuration, and an aluminum crossflow cylinder head versus the iron head of the B20.

The Subaru EJ engine is a series of four-stroke automotive engines manufactured by Subaru. They were introduced in 1989, intended to succeed the previous Subaru EA engine. The EJ series was the mainstay of Subaru's engine line, with all engines of this series being 16-valve horizontal flat-fours, with configurations available for single, or double-overhead camshaft arrangements. Naturally aspirated and turbocharged versions are available, ranging from 96 to 310 hp. These engines are commonly used in light aircraft, kit cars and engine swaps into air-cooled Volkswagens, and are also popular as a swap into copy wasserboxer engined Volkswagen T3/Vanagon. Primary engineering on the EJ series was done by Masayuki Kodama, Takemasa Yamada and Shuji Sawafuji of Fuji Heavy Industries, Subaru's parent company.

The Family II is a straight-4 piston engine that was originally developed by Opel in the 1970s, debuting in 1981. Available in a wide range of cubic capacities ranging from 1598 to 2405 cc, it simultaneously replaced the Opel CIH and Vauxhall Slant-4 engines, and was GM Europe's core mid-sized powerplant design for much of the 1980s, and provided the basis for the later Ecotec series of engines in the 1990s.

The Mercedes-Benz OM606 is a 3.0 litres (2,996 cc) inline-six cylinder (R6/I6) double overhead camshaft (DOHC) diesel engine with indirect injection manufactured by Mercedes-Benz between 1993 and 2001. It replaced the single overhead camshaft (SOHC) OM603 engine.

The Mercedes-Benz OM605 is a 2.5 L (2,497 cc) inline-five cylinder (R5/I5) double overhead camshaft (DOHC) diesel engine with indirect injection manufactured by Mercedes-Benz between 1993 and 2001. It replaced the single overhead camshaft (SOHC) OM602 engine.

The Mercedes-Benz OM604 is a 2.0 litres (1,997 cc) and 2.2 litres (2,155 cc) inline-four cylinder (R4/I4) double overhead camshaft (DOHC) diesel engine with indirect injection manufactured by Mercedes-Benz between 1993 and 1998. It replaced the single overhead camshaft (SOHC) OM601 engine. Unlike other Mercedes Benz diesels at the time that used a Bosch inline injection pump the OM604 used the Lucas electronically controlled rotary distributor injection pump (EVE) which is less reliable. The seals of the Lucas injection pumps become brittle over time and leak, a seal kit is available

References

↑ "1991 Saturn S-Series Features & Specs". edmunds.com. 1991. Retrieved 2012-10-30.
↑ "1995 Saturn S-Series Features & Specs". edmunds.com. 1995. Retrieved 2012-10-30.
↑ Saturn corporation specification sheet as shown on website http://www.saturnfans.com/photos/showphoto.php?photo=53949
↑ "1992 Saturn S-Series Features & Specs". edmunds.com. 1992. Retrieved 2012-10-30.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[Edmunds-1] "1991 Saturn S-Series Features & Specs". edmunds.com. 1991. Retrieved 2012-10-30.

[Edmunds2-2] "1995 Saturn S-Series Features & Specs". edmunds.com. 1995. Retrieved 2012-10-30.

[3] Saturn corporation specification sheet as shown on website http://www.saturnfans.com/photos/showphoto.php?photo=53949

[Edmunds3-4] "1992 Saturn S-Series Features & Specs". edmunds.com. 1992. Retrieved 2012-10-30.

[1]

[2]

[3]

[4]