Turbo-Thrift | |
---|---|
Overview | |
Manufacturer | Chevrolet |
Production | 1962–1988 1964–2001 (Brazil) 1964–1999 (South Africa) 1962–2001 (Argentina) |
Layout | |
Displacement | 194 cu in (3.2 L) 230 cu in (3.8 L) 250 cu in (4.1 L) 292 cu in (4.8 L) |
Cylinder bore | 3+9⁄16 in (90.5 mm) 3+7⁄8 in (98.4 mm) |
Piston stroke | 3+1⁄4 in (82.6 mm) 3.53 in (89.7 mm) 4+1⁄8 in (104.8 mm) |
Cylinder block material | Cast iron |
Cylinder head material | Cast iron |
Valvetrain | OHV 2 valves per cyl. |
Combustion | |
Fuel system | Rochester one barrel Carburetor Multi-port fuel injection |
Fuel type | Gasoline |
Oil system | Wet sump |
Cooling system | Water-cooled |
Dimensions | |
Length | 32.5 in (830 mm) |
Chronology | |
Predecessor | Chevrolet Stovebolt engine |
Successor | Chevrolet 90° V6 engine |
The Chevrolet Turbo-Thrift engine is a straight-six produced from 1962 to 2001 by the Chevrolet division of General Motors. The entire series of engines was commonly called Turbo-Thrift, although the name was first used on the 230 cubic inch version that debuted in 1963. [1] The new engine featured seven main bearings in lieu of the four bearing design of its predecessor, the "Stovebolt" engine, and was considerably smaller and approximately 100 lbs lighter. [2]
There were other major differences between the Turbo-Thrift engine and the Stovebolt:
The first use of the new engine series was the 194 cu in (3.2 L)Hi-Thrift version in the 1962 Chevy II; the following year, Chevrolet passenger cars adopted the 230 cu in (3.8 L) version across the range. Studebaker and Checker also began using the engine in 1965. [3] : 341 Chevrolet and GMC trucks, which previously used the Stovebolt and GMC V6 engines, also switched to using the Turbo-Thrift from 1963 through 1988, as did Pontiac in 1964 and 1965. A 153-cubic-inch (2.5 L) inline-4 version of this engine was also offered in the Chevy II/Nova line through the 1970 model year.
After several years of steadily declining sales (just 3,900 units in the 1972 model year), [3] : 881 the straight-six was dropped from Chevrolet's full-sized cars for 1973, the first time the full-sized Chevrolet had not been available with a six-cylinder since 1928. However, when the B-body line was downsized in 1977, the engine was reintroduced. [3] : 881 The base six cost about US$334 less than a V8, and weighed some 188 lb (85 kg) less. [3] : 881
Overseas, the engine was also mass-produced in Brazil. It was used in the Chevrolet Opala from 1969 (230) to 1992 (250). It was also used in light trucks, including the Chevrolet Veraneio. The Brazilian version of the GMT400 – the Brazilian Chevrolet Silverado – is powered with a 4.1 instead of the Vortec 4300 V6. Brazilian-produced sixes manufactured to the 2001 model year gained multipoint fuel injection, unlike the US-manufactured sixes, which retained the Rochester Monojet one-barrel carburetor. These inline-sixes and their four-cylinder siblings were converted for marine usage by Mercruiser and Volvo Penta, and also used in stationary applications (such as power generation) and in Clark forklifts. [4] Aftermarket port fuel injection and re-engineered cylinder heads have been the norm, although parts for the inline-six, such as aftermarket intake manifolds (from a three-carburetor setup or a single 4-barrel carburetor), exhaust headers, and hybrid cylinder heads based on Chevrolet's small-block engine are costlier than those for the small-block, unlike the rival AMC inline-six (which has a cult following with Jeep enthusiasts, especially with the 4.0 L). Chevrolet's inline-six engine was also manufactured in Argentina and South Africa.
The Hi-Thrift 194 was introduced as the optional engine in the 1962 Chevy II. Bore and stroke are 3+9⁄16 in × 3+1⁄4 in (90 mm × 83 mm), for a total displacement of 194 cu in (3,185 cc). [5] It was also optional in the 1964 G10 Chevy Van 1⁄2-ton vans, and standard in the G10 in 1965 and 1966; it was not available in the C/K10 1⁄2-ton trucks. [6] The engine produced peak power of 120 hp (89 kW) (gross) and 177 lb⋅ft (240 N⋅m) of torque. [7]
The 194 variant ended production in North America after 1967, but remained in use by General Motors' Argentinian subsidiary until the mid-1970s. GM de Argentina also developed a 109.7 cu in (1,797 cc) four-cylinder version called the "Chevrolet 110" for their Opel K 180 compact car. [8]
Pontiac's 215 cu in (3.5 L) (1964–1965) was a smaller bore of 3.75 in (95.25 mm) version of the 230 cu in (3.8 L) Chevrolet straight-six engine. One oddity is the crankshaft bolt pattern; in lieu of the Chevrolet V8 bolt pattern (also shared with the rest of the third-generation six), the Pontiac V8 bolt pattern is used.
The Turbo-Thrift 230 (also known as the High Torque 230 in Chevrolet trucks), with 230 cu in (3,768 cc) displacement, replaced the long-stroke 235 cu in (3.9 L) version of the Stovebolt six beginning in 1963. Bore and stroke were 3+7⁄8 in × 3+1⁄4 in (98 mm × 83 mm). It was also used by Chevrolet and GMC trucks, primarily for the half-tons. It produced a peak 140 hp (104 kW) at 4,400 rpm and 220 lb⋅ft (298 N⋅m) at 1,600 rpm. North American production of this variant ceased in 1970. It was also built in Latin America and was in production in South Africa until at least 1982, where it powered a multitude of different cars. A four-cylinder version of this engine was also built, the Super-Thrift 153.
The Turbo-Thrift 250 (also known as the High Torque 250 in trucks) version was introduced in 1966, with the same 3.875 in (98.4 mm) bore as the 230 and a longer 3.53 in (90 mm) stroke for a larger 249.8 cu in (4.1 L; 4,093 cc) displacement. Between 1975 and 1984, an integrated cylinder head was produced (intake manifold and cylinder head were a single casting with a bolt on exhaust manifold), with one-barrel intakes for passenger cars, and two-barrel intakes for trucks after 1978. The "integrated" cylinder head and intake manifold claimed to have resulted in increased low end torque and fuel economy inclusive of a smoother operation, lowering NVH (noise, vibration, and harshness).
The engine was sold in various states of tune and under several different RPO codes over its production life. The L22 was the passenger car version, sold until 1979. The LD4 was the truck version, sold until 1978. The LE3 replaced the LD4 in 1979 and was produced until 1984.
In the late 1970s, the Chevrolet 200, Chevrolet 229 and Buick 231 V6 engines gradually replaced the 250 straight six in passenger cars in North America, with use of the engine discontinued after the 1979 model year. The 250 engine continued to be used in GM trucks until 1984, after which it was replaced by the 4.3 L V6 (essentially a 350-cubic-inch (5.7 L) Chevy small-block V8 with the two rear cylinders removed). It was also used in a number of large sedans by Chevrolet of South Africa until 1982.
Production continued in Brazil (known as the 4.1 there) until 1998 in passenger cars, when the Chevrolet Omega A was replaced by rebadged Australian Holdens. It was used until 2001 in the Brazilian Chevrolet Silverado, after which the engine line was discontinued. Latter-day Brazilian-produced engines featured electronic multipoint fuel injection, distributorless ignition system and redesigned cylinder heads with smaller intake ports.
GM did not produce another straight-six engine in North America until the introduction of the GM Atlas engine in late 2001.
Year | Compression Ratio | Power [A] | Torque [A] | Notes | Reference |
---|---|---|---|---|---|
1966–1970 | 8.5:1 | 155 hp (116 kW) @ 4200 rpm | 235 lb⋅ft (319 N⋅m) @ 1600 rpm | [12] [15] [16] [19] [20] [21] [22] [23] [17] [24] [25] [26] [27] [28] [29] | |
1971 | 145 hp (108 kW) @ 4200 rpm | 230 lb⋅ft (312 N⋅m) @ 1600 rpm | [30] [31] | ||
1972 | 110 hp (82 kW) @ 3800 rpm | 185 lb⋅ft (251 N⋅m) @ 1600 rpm | [32] [33] | ||
1973–1974 | 8.25:1 | 100 hp (75 kW) @ 3600 rpm | 175 lb⋅ft (237 N⋅m) @ 1600 rpm | [34] [35] [36] [37] [38] | |
1975–1976 | 105 hp (78 kW) @ 3800 rpm | 185 lb⋅ft (251 N⋅m) @ 1200 rpm | "Integrated" cylinder head introduced | [39] [40] [41] [42] | |
1977 | 8.3:1 | 110 hp (82 kW) @ 3800 rpm | 195 lb⋅ft (264 N⋅m) @ 1600 rpm | L22, Federal emissions; LD4, light-duty emissions | [43] [44] |
90 hp (67 kW) @ 3600 rpm | 180 lb⋅ft (244 N⋅m) @ 1600 rpm | L22, California emissions | |||
8.0:1 | 100 hp (75 kW) @ 3600 rpm | 175 lb⋅ft (237 N⋅m) @ 1800 rpm | LD4, heavy-duty emissions | ||
1978 | 8.1:1 | 110 hp (82 kW) @ 3800 rpm | 190 lb⋅ft (258 N⋅m) @ 1600 rpm | L22, Federal emissions | [45] [46] |
90 hp (67 kW) @ 3600 rpm | 175 lb⋅ft (237 N⋅m) @ 1600 rpm | L22, California emissions | |||
100 hp (75 kW) @ 3800 rpm | 185 lb⋅ft (251 N⋅m) @ 1600 rpm | LD4, light/medium-duty California emissions | |||
8.0:1 | 115 hp (86 kW) @ 3800 rpm | 195 lb⋅ft (264 N⋅m) @ 1600 rpm | LD4, light-duty Federal emissions | ||
100 hp (75 kW) @ 3600 rpm | 175 lb⋅ft (237 N⋅m) @ 1800 rpm | LD4, heavy-duty Federal emissions | |||
1979 | 8.0:1 | 115 hp (86 kW) @ 3800 rpm | 200 lb⋅ft (271 N⋅m) @ 1600 rpm | L22, Federal emissions | [47] [48] |
8.2:1 | 90 hp (67 kW) @ 3600 rpm | 175 lb⋅ft (237 N⋅m) @ 1600 rpm | L22, California emissions | ||
8.3:1 | 130 hp (97 kW) @ 4000 rpm | 210 lb⋅ft (285 N⋅m) @ 2000 rpm | LE3, light/medium-duty Federal emissions | ||
125 hp (93 kW) @ 4000 rpm | 205 lb⋅ft (278 N⋅m) @ 2000 rpm | LE3, light-duty California emissions; C/K10 trucks and G10 vans only | |||
130 hp (97 kW) @ 4000 rpm | 205 lb⋅ft (278 N⋅m) @ 2000 rpm | LE3, light/medium-duty California emissions; C20 trucks and G20/G30 vans only | |||
1980 | 130 hp (97 kW) @ 4000 rpm | 210 lb⋅ft (285 N⋅m) @ 2000 rpm | LE3, light-duty Federal emissions | [49] | |
125 hp (93 kW) @ 4000 rpm | 205 lb⋅ft (278 N⋅m) @ 2000 rpm | LE3, light-duty California emissions; C/K10 trucks and G10 vans only | |||
130 hp (97 kW) @ 4000 rpm | 205 lb⋅ft (278 N⋅m) @ 2000 rpm | LE3, medium-duty California emissions; C20 trucks and G20/G30 vans only | |||
1981–1982 | 115 hp (86 kW) @ 3800 rpm | 200 lb⋅ft (271 N⋅m) @ 2000 rpm | LE3, Federal emissions | [50] [51] | |
105 hp (78 kW) @ 3600 rpm | 195 lb⋅ft (264 N⋅m) @ 1600 rpm | LE3, California emissions | |||
1983 | 120 hp (89 kW) @ 4000 rpm | 205 lb⋅ft (278 N⋅m) @ 2000 rpm | LE3, Federal emissions | [52] | |
110 hp (82 kW) @ 3600 rpm | 200 lb⋅ft (271 N⋅m) @ 2000 rpm | LE3, California emissions | |||
1984 | 115 hp (86 kW) @ 3600 rpm | 200 lb⋅ft (271 N⋅m) @ 2000 rpm | LE3, Federal emissions | [53] | |
110 hp (82 kW) @ 3600 rpm | 200 lb⋅ft (271 N⋅m) @ 1600 rpm | LE3, California emissions |
A power and torque figures in this table are SAE gross until 1971; thereafter, they are SAE net |
When long distance racing restarted in Brazil in 1973, the Chevrolet Opala and the Ford Maverick were the main contenders. The Maverick's engine was almost one liter larger than the Opala's, however. Drivers Bob Sharp and Jan Balder, who shared a ride to second place in the "24 Hours of Interlagos" in August of that year in an Opala, pressured General Motors do Brasil to field a more powerful racing engine.
By coincidence, engine development manager Roberto B. Beccardi had already been working on such a performance engine project out of his own initiative, but had lacked factory support or approval. Thus, in July 1974, GM started to offer the 250-S engine as an option for the Opala 4100. It was slightly different from the version launched two years later: the project engine was similar to the four-cylinder units, did not get a vibration damper, and used the cooling fan from the standard 2500, with four blades instead of six.
The Opala was now much faster than the Maverick GT and Ford did not waste time. It quickly homologated a version with four-barrel carburetor, called "Quadrijet" in Brazil (no relationship to GM's own Rochester Quadrajet), with performance roughly equivalent to the 250.[ citation needed ]
The 250-S has 171 hp (126 kW) and 229.7 lb⋅ft (311 N⋅m) at 2,400 rpm.
The High Torque 292 engine, displacing 292 cubic inches (4.8 L), was used in Chevrolet and GMC trucks beginning in 1963 and Step-Van/Value-Vans beginning in 1964. It was also the standard engine in the Chevy Van/GMC Vandura G20 and G30 from 1975 to 1978. It is differentiated from the 194/230/250 engines by a 1+3⁄4 inches (44.5 mm) taller block deck and relocated passenger-side engine mount. Although it had had a larger displacement than its 261-cubic-inch (4.3 L) Stovebolt predecessor it was approximately 2 inches (51 mm) shorter and 1⁄4 inch (6.4 mm) lower. [54] Flywheel bolt pattern is the same as the six and V8, with 1⁄2 inch (12.7 mm) bolts for the flywheel if produced after the 1966 model year.
Production of the engine was shifted to Mexico in 1980, and later variants of this engine were marketed as the High Torque 4.8 L and by its RPO code L25 It retained the separate intake (with a Rochester Monojet carburetor) and exhaust manifolds as used with the short deck motors (194–250).
Availability of the 4.8 L engine was slowly curtailed from the late 1970s until production ceased entirely in 1989, and it was replaced by the 4.3 L V6. By 1987, it was only available (outside of California) as an option in 3⁄4-ton and 1-ton R/V-series trucks, and as the base engine in P20 and P30 Step-Vans.
Year | Compression Ratio | Power [A] | Torque [A] | Notes | Reference |
---|---|---|---|---|---|
1963 | 8.0:1 | 165 hp (123 kW) @ 3800 rpm | 280 lb⋅ft (380 N⋅m) @ 1600 rpm | [13] | |
1964–1970 | 170 hp (127 kW) @ 4000 rpm | 275 lb⋅ft (373 N⋅m) @ 1600 rpm | [14] [15] [20] [23] [25] [27] [29] | ||
1971 | 165 hp (123 kW) @ 4000 rpm | 270 lb⋅ft (366 N⋅m) @ 1600 rpm | [31] | ||
1972 | 125 hp (93 kW) @ 3600 rpm | 225 lb⋅ft (305 N⋅m) @ 2400 rpm | [33] | ||
135 hp (101 kW) @ 3800 rpm | 240 lb⋅ft (325 N⋅m) @ 2000 rpm | CS50, SS50 trucks | |||
1973–1978 | 120 hp (89 kW) @ 3600 rpm | 215 lb⋅ft (292 N⋅m) @ 2000 rpm | [35] [38] [40] [42] [44] [46] | ||
1979–1982 | 7.8:1 | 115 hp (86 kW) @ 3400 rpm | 215 lb⋅ft (292 N⋅m) @ 1600 rpm | [48] [49] [50] [51] | |
1983–1986 | 115 hp (86 kW) @ 3600 rpm | 215 lb⋅ft (292 N⋅m) @ 1600 rpm | [52] [53] [55] [56] | ||
1987–1989 | 115 hp (86 kW) @ 4000 rpm | 210 lb⋅ft (285 N⋅m) @ 800 rpm | Only available in R/V-series trucks outside California for 1987 and 1988 Also available in P20 and P30 vans | [57] [58] |
A power and torque figures in this table are SAE gross until 1971; thereafter, they are SAE net |
GMC is a division of American automotive manufacturer General Motors (GM) for trucks and utility vehicles. GMC currently makes SUVs, pickup trucks, vans, and light-duty trucks. In the past, GMC also produced fire trucks, ambulances, heavy-duty trucks, military vehicles, motorhomes, transit buses, and medium duty trucks.
The Chevrolet S-10 is a compact pickup truck produced by Chevrolet. It was the first domestically-built compact pickup of the big three American automakers. When it was first introduced as a "quarter-ton pickup" in 1981 for the 1982 model year, the GMC version was known as the S-15 and later renamed the GMC Sonoma. A high-performance version of the latter was released in 1991, called "Syclone." The pickup was also sold by Isuzu as the Hombre from 1996 through 2000, but only in North America. There was also an SUV version, the Chevrolet S-10 Blazer/GMC S-15 Jimmy. An electric version was leased as a fleet vehicle in 1997 and 1998. These models are sometimes internally referred to as the S/T series to denote two and four wheel drive models respectively despite all versions being badged with 'S' nomenclature.
The Chevrolet C/K is a series of trucks that was manufactured by General Motors from the 1960 to 2002 model years. Marketed by both the Chevrolet and GMC divisions, the C/K series encompassed a wide range of vehicles. While most commonly associated with pickup trucks, the model line also included chassis-cab trucks and medium-duty trucks and served as the basis for GM full-size SUVs. Through its entire production, the model line competed directly against the Ford F-Series and the Dodge D series.
The Chevrolet Stovebolt engine is a straight-six engine made in two versions between 1929 and 1962 by the Chevrolet Division of General Motors. It replaced the company's 171-cubic-inch (2.8 L) inline-four as their sole engine offering from 1929 through 1954, and was the company's base engine starting in 1955 when it added the small block V8 to the lineup. It was completely phased out in North America by 1962, but GM continued to build it in Brazil until 1979. It was replaced by the Chevrolet Turbo-Thrift engine.
The Chevrolet Express is a series of full-size vans produced by General Motors since 1996. The successor to the Chevrolet G-series van, the Express is produced in passenger and cargo variants. Alongside the standard van body, the line is offered as a cutaway van chassis; the latter vehicle is a chassis cab variant developed for commercial-grade applications, including ambulances, buses, motorhomes, and small trucks.
The Chevrolet Chevy II/Nova is a small automobile manufactured by Chevrolet, and produced in five generations for the 1962 through 1979, and 1985 through 1988 model years. Built on the X-body platform, the Nova was the top selling model in the Chevy II lineup through 1968. The Chevy II nameplate was dropped after 1968, with Nova becoming the nameplate for all of the 1969 through 1979 models. It was replaced by the 1980 Chevrolet Citation introduced in the spring of 1979. The Nova nameplate returned in 1985, produced through 1988 as a S-car based, NUMMI manufactured, subcompact based on the front wheel drive, Japan home-based Toyota Sprinter.
The Pontiac straight-6 engine is a family of inline-six cylinder automobile engines produced by the Pontiac Division of General Motors Corporation in numerous versions beginning in 1926.
The Chevrolet Opala is a Brazilian mid-size car sold under the Chevrolet brand in South America from 1969 to 1992, by General Motors do Brasil. It was derived from the German Opel Rekord Series C, Opel Commodore Series A, but used local design styling and engines derived from North American designs. GM manufactured about one million units including the Opala sedan, Opala Coupé, and the station wagon variant, the Opala Caravan. It was replaced by the Chevrolet Omega in 1992, also an Opel spinoff. It was the first passenger car built by GM in Brazil by the General Motors do Brasil division. A luxury version of the Opala was marketed as the Chevrolet Diplomata.
The GM A platform was a rear wheel drive automobile platform designation used by General Motors from 1925 until 1959, and again from 1964 to 1981. In 1982, GM introduced a new front wheel drive A platform, and existing intermediate rear wheel drive products were redesignated as G-bodies.
The GMC Brigadier is a series of heavy-duty trucks that were assembled by the GMC Truck and Coach Division of General Motors. The second generation of the H/J-series heavy-duty conventionals, the Brigadier was produced from 1978 to late 1989, as a WhiteGMC for the last year and a half. Slotted between the largest medium-duty C/K trucks and the GMC General, the Brigadier was a Class 7-8 short-hood conventional similar to the Ford L-Series and Mack Model R. Configured in both straight truck and semi-tractor layouts, the Brigadier saw use in short-haul, vocational, and severe-service applications.
The Chevrolet 90° V6 family of V6 engines began in 1978 with the Chevrolet 200 cu in (3.3 L) as the base engine for the all new 1978 Chevrolet Malibu. The original engine family was phased out in early 2014, with its final use as the 4.3 L (262 cu in) V6 engine used in Chevrolet and GMC trucks and vans. Its phaseout marks the end of an era of Chevrolet small-block engine designs dating back to the 1955 model year. A new Generation V 4.3 L (262 cu in) V6 variant entered production in late 2013, based on the LT1 small block V8 and first used in the 2014 Silverado/Sierra 1500 trucks.
The Chevrolet 153 cu in engine was an inline-four engine designed in the early 1960s for use in the Chevy II. It is a four-cylinder variant of the Turbo-Thrift six-cylinder engine. After 1970, GM ceased production of the 153 engine in North America because of low demand, but the engine continued to be used in cars in other markets around the world, notably in South Africa and South America. The engine was also standard equipment in the Jeep DJ-5A—used by the United States Postal Service—until American Motors bought Kaiser Jeep in 1970 and replaced the engine with the AMC straight-six in the DJ-5B. Currently descendants of the 153 engine are used in industrial and marine applications. The 153 engine is entirely different from the 151 cu in (2.5 L) Iron Duke engine introduced by Pontiac in 1977, most noticeably never having featured the Pontiac engine's crossflow cylinder head, but the two are often confused today.
The Chevrolet Van or Chevy Van is a range of vans that was manufactured by General Motors from the 1964 to 1996 model years. Introduced as the successor for the rear-engine Corvair Corvan/Greenbrier, the model line also replaced the panel van configuration of the Chevrolet Suburban. The vehicle was sold both in passenger van and cargo van configurations as well as a cutaway van chassis that served as the basis for a variety of custom applications.
The Chevrolet Series CA Eagle and Master is an American vehicle manufactured by Chevrolet in 1933 to replace the 1932 Series BA Confederate. The car was called "Eagle" early in the 1933 production year. When it was joined by the cheaper Chevrolet Standard Six later in February, 1933 the Eagle name was changed to "Master" to provide Chevrolet with a two-car range, and for the first time in ten years they manufactured two models on different wheelbases. Starting in 1926, GM introduced the short lived General Motors companion make program where Oakland, Oldsmobile, Buick and Cadillac had "companion" models added to each division. The only division that didn't get a "junior" brand was Chevrolet; instead, the lower-priced Standard series was introduced.
The first generation of the C/K series is a range of trucks that was manufactured by General Motors from the 1960 to 1966 model years. Marketed by both the Chevrolet and GMC divisions, the C/K trucks replaced the previous Task Force generation of trucks. The first General Motors pickup trucks developed on a dedicated truck platform, the C/K series included pickup trucks, chassis-cab trucks, and medium/heavy commercial trucks.
The second generation of the C/K series is a range of trucks that was manufactured by General Motors. Marketed by both the Chevrolet and GMC divisions from the 1967 to 1972 model years, this generation was given the "Action Line" moniker by General Motors. As with its predecessor, the second generation C/K included full-size pickup trucks, chassis cab trucks, and medium-duty commercial trucks.
The fourth generation of the C/K series is a range of trucks that was manufactured by General Motors. Marketed by the Chevrolet and GMC brands from the 1988 to the 2002 model years, this is the final generation of the C/K model line. In a branding change, GMC adopted the GMC Sierra nameplate for all its full-size pickup trucks, leaving the C/K nomenclature exclusive to Chevrolet.
The Chevrolet Step-Van is a multi-stop truck made by General Motors from 1940 to 1999.
Saginaw Metal Casting Operations is an automobile engine foundry plant in Saginaw, Michigan. Opened under GM management in 1919, the factory produces engine blocks and cylinder heads for General Motors vehicles. The factory currently occupies 1.9 million square feet on 490 acres. Historically in September 1927 it was known as the Chevrolet Grey Iron Foundry. In the past when it was called GM-Saginaw Product Company (SPC) a cloverleaf casting symbol mark was cast onto the iron component.
...the 230 inch version that appeared in the full-size 1963 Chevys, finally replacing the venerable 235 incher "Blue Flame" was called Turbo-Thrift, and the family is typically known by that name.