The Holden V8 engine, also known colloquially as the Iron Lion engine, is an overhead valve (OHV) V8 engine that was produced by the Australian General Motors subsidiary, Holden (GMH), between 1969 and 2000.
The engine was initially fitted to the Holden HT series in 1969 and was later utilised in a series of updated versions in the Torana and Commodore ranges. The final iteration, the heavily revised HEC 5000i, was phased out of Holden passenger vehicles with the release of the VT Series II Commodore and the WH Statesman and Caprice in June 1999, both of which featured the 5.7L Gen III V8 imported from the United States. However, the engine remained in production for a little while longer and continued to be available in the Commodore VS Series III utility (which sold alongside the VT sedan and wagon as no similar vehicle was available in that range) until the new generation VU Ute debuted in late 2000.
In addition to being Holden's mainstream performance engine throughout its production run, higher performance versions were fitted to limited-edition vehicles available through Holden Dealer Team Special Vehicles (HDT) and later Holden Special Vehicles (HSV). It was also utilised within limited production vehicles from other manufacturers as well as in kit cars.
In 1964 Ford and Chrysler in the US released V8 versions of their respective Falcon and Valiant models which Holden expected to soon be released in locally assembled or produced versions. In response, in January 1965 the company's engineering division initiated a forward engine program review and concluded that by 1969 a V8 option was a necessity for Holden, with forecasts of 35 per cent of all Holdens sold in 1970 to be V8s, rising to 50 per cent by 1975. Initially six capacities from 237–308cuin (3,880–5,050cc) were planned over a 12-year life cycle, but early in the design phase this was reduced to just two, an 'economy' 253ci (4143cc) and an enlarged 'performance' 308ci (5044cc) version, which became known as the 4.2L[lower-alpha 1] and 5.0L respectively.[2]
Design targets of a weight of 525lb (238kg), which was lighter than equivalent US engines, and a net output of and 161hp (120kW) at 4000rpm and 263lb⋅ft (357N⋅m) at 2400rpm were set for the 308, which was mechanically identical to the 253 except for a larger bore and bigger pistons, along with heavier counterweights on the crankshaft to compensate for the increased reciprocating mass. Originally an alloy inlet manifold was specified to reduce weight, but this was changed to iron when problems were encountered in the casting process. The exhaust manifolds were also cast iron but the timing case cover remained as an alloy item.[2][3]
The initial pre-production engine was the 253, which not only met but greatly exceeded the design targets. The complete engine assembly from fan to flywheel and all auxiliaries weighed in at 460lb, around 12% less than the design target, while net output for the higher compression (9.0:1) version fitted with a 2-barrel carburettor[lower-alpha 2] was 185hp (138kW) with 262lb.ft of torque, which matched or exceeded the targets set for the larger 308. The design was also very compact with a width of 22 inches, and was only 80lb heavier than the 186cuin (3,050cc) straight six, but producing over 40% (55hp (41kW)) more power than that engine in standard form. The first running engine was delivered in October 1966. Unfortunately, the engine failed after just four days testing from a seized oil pump; however, the problem was found to be caused by swarf residue rather than a fault in the design or the quality of the components. Further testing proved that the engine was smoother and more durable than Holden's six cylinder, no mean feat as the 186 was considered a smooth and reliable engine in its day.[3][5]
The new engines were initially intended to be offered as part of the 1968 Holden HK range, but production issues caused the project to run behind schedule and consequently 307ci Chevrolet engines imported from Canada were used instead. Initially the 283ci engine was to be used but it was replaced in North America for the 1968 GM model year with the 307ci engine hence it was used instead for HK. GMH had already planned to use the 327ci Chevrolet engine in the HK GTS327 and it would have originally been fitted in the HK range alongside 253 and 308 if things had gone as planned. The 253 made its public debut in the Holden Hurricane concept car at the 1969 Melbourne International Motor Show, albeit it in a highly modified form featuring increased 10.1:1 compression, big cam and solid lifters, and producing over 250hp (190kW). The new engines saw their production release soon after in the HT model range, with the 253 being used for manual vehicles whilst the 307 SBC was retained for automatic vehicles. The 308 however debuted in the HT Brougham at the same time but as automatic only (two different imported 350ci Chevrolet engines (auto and manual versions) replaced the 327 and thus the HK GTS327 became the HT GTS350). The 253 was initially only available with a 2-barrel carburettor while the 308 was only ever available with a 4-barrel carburettor (except for when it was used in Bedford trucks in the late 70's).[2] Once the Canadian 307ci engines were used up the 308 became available across all models in the HT range, including the 2-door Monaro coupe. At the same time an automatic option was made available behind the 253 and a manual was available behind the 308 (previously automatic only when 308 was only available in Brougham).
5.0L; 307.8cuin (5,044cc) V8
The 253 and 308 soldiered on essentially unchanged into the HG Holden and HQ Holden Series. The V8 engine also appeared from 1971 in the Statesman range of large size luxury cars which Holden established as a separate marque replacing the Holden-badged Brougham. Initially both the 253 and 308 (and imported 350ci engine) were offered in the HQ V8 Statesman model and 308 standard in HQ Deville but after HQ both the 6cyl and V8 Statesman (Custom) models were dropped leaving the 308 powered HJ Statesman Deville as the base Statesman variety. This continued for the HX, HZ and WB.
At the end of HQ (and earlier for LH Torana release) the 253 and 308 engines were referred to by their metric names: 4.2L and 5.0L. Apart from minor external changes like cable throttle and things to make it fit the Torana properly the 4.2L engine in HJ and LH was the same as the HQ engine. At the HQ to HJ transition GMH changed the power output figures on all engines from "advertised horsepower" to proper GM20 test "SAE Gross hp". The power ratings on all engines dropped. The HT-HQ advertised power figures for the 253 and 308 were respectively: 185hp and 240hp. The SAE Gross figures for these engines was 175hp and 227hp. GMH Technical and Engineering literature shows these revised power figures for HJ but it took a while for it to appear in Sales literature - LX Torana release information shows the 4.2L as 175hp and the 5.0L as 250hp. The HJ 5.0L was a very different engine to the HT-HQ 308 though. It got a raise in compression from 9:1 to 9.7:1 and got a new camshaft which was basically the same valve timing as used in the HK-HQ SBC engines (prior to HJ the 308 used the 253's smaller camshaft but retarded 5 degrees). The revised 5.0L was SAE Gross rated as 250hp which was a 23hp gain on the HQ 308. In LH SLR5000 Toranas built after HJ release and LX SLR5000 and SS with RPO L31 built prior to HX Holden this revised 5.0L engine created a very fast car. The revised 5.0L engine performed so well that GMH dropped the planned 400ci engine from HJ Caprice and other optioned HJ Holden as the emissions strangled 400ci SBC out of North America was no benefit over the local 5.0L. The flip side of the extra power and torque meant that the Trimatic transmission that was used prior to HJ was not strong enough for the revised 5.0L in a full size Holden or Statesman so it was replaced with the imported TH400 transmission.
In 1974, both the 253 and 308 engines (now called 4.2L and 5.0L) were added to the Torana range for the first time in the LH series (after an aborted attempt by Holden Dealer Team boss Harry Firth to introduce the V8 to the smaller LJ in 1972 which was stopped by the "supercar scare"). In fact the SLR5000 only weighed 40kg more than the XU-1. Some of the lower performance Toranas were light, but the six-cylinder LJ XU-1 weighs 1140 kg while the SLR5000 L34 only weighed 1180 kg with the high performance V8. The engines were also offered on the revised LX released in 1976, which from July of that year saw emission-controlled versions of the 'Red' engines introduced to comply with the new ADR27A regulations on fuel and exhaust emissions. The V8 was dropped as an option in the final model in the Torana series, the UC released in 1978. There was a high performance version of the 308 engine built in 1973 by Repco for the Formula 5000 series. It was built as a 302ci (4940cc) engine using a slightly smaller bore than the production 308 (3.960" versus the 308's 4"). It was a far stronger block than the production block and featured 4 bolt mains and 11.7:1 compression with either Lucas fuel injection or Weber carburettors. GMH asked REPCO to use some of the ideas and parts for this engine and produced the higher performance 308 engine (engine code L34). The LH SLR5000 was released that used a standard 5.0L engine. A little while into LH, GMH built a limited number of SLR5000 vehicles (263) with an engine code L34 along with a whole host of other parts fitted to it for manufacturers championship endurance rounds. And you had to use the complete car complianced with the motor. The whole car was homoligated. In the A9X they had to use the L34 motor. Due to the Supercar scare the car which was the fastest production car in the world (in the future all hot 308s were aftermarket delivered not Holden Production line) still lower in HP.HDT HSV. It had more power than most of its combinations in the future mainly due to its high compression motor. It had larger valves, and a four-barrel inlet, 750cfm carb. Due to the rules of the day race teams could put any carby with same number of venturies and modify the exhaust from the first join. So the as delivered headers were not that good lowering the as delivered cars power down to near stock. But when set up for race it had excessive amounts of power. Cam and carby were open as well so the cars internals where heavy duty and designed to flow. But cam carby and exhaust due to cams rules could keep it tame. The L34 was never advertised except when wheels found out about it. Only cams licensed teams could buy one. The car eventually was nicknamed the L34 The letters L34 were the engine code and thats how the L34 got its name. The L34 had the code on the model plate there is nothing on an A9X that states its an A9X and the A9X had to use the L34 motor from an L34 to rsce.
In 1978 with the introduction of the new smaller Commodore as Holden's family car, the final versions of the 'Red' 253 and 308 were available with the initial VB. In 1980 the revised VC saw the introduction of the revised 'Blue' series of engines, available in both capacities, which continued through to the VH in 1982. The VC also saw the introduction of high-performance versions of the engine but mostly L34 parts still. All performance parts on parts list at HDT state L34. in limited-edition vehicles produced in partnership with Peter Brock's Holden Dealer Team (HDT), with various models subsequently appearing through to the VL range in 1987, when relations between the two companies soured and Holden severed its ties with HDT.
With the release of the 'Black' engine in the VK Commodore in 1984, the 253 was dropped as an option and the 308 was the only capacity of the V8 now available in the Commodore. However, the smaller engine continued to be available in the Holden WB commercial vehicles e.g. the One Tonner cab chassis until the end of 1984. In 1985, a destroked version of the 308, known as the 304 but still sold as a 5.0L engine, was introduced to allow the VK to compete with a lower minimum weight (1325kg, a saving of 75kg) under the 4501-5000cc regulations of Group Atouring car racing.[6]
In 1988 fuel injection appeared for the first time on a Holden V8 engine, on the VL Commodore SS Group A produced by Holden Special Vehicles (HSV), Holden's new performance partnership with British-based Tom Walkinshaw Racing (TWR); however, this was not a standard production engine, which still continued to feature a carburettor. Later that year the VN introduced the 5000i engine with new cylinder heads and multi-point fuel injection which represented the most extensive redesign of the standard production Holden V8 since its launch in 1969. This engine continued in all subsequent Commodores until 1999 (2000 for the VS Series III Ute), when it was replaced by the US-made all-alloy Gen III LS1 5.7L V8 in the VT Series II.
Design
The Holden V8 is a water-cooled naturally-aspirated 4-stroke gasoline engine featuring eight cylinders arranged in a 90 degrees vee-formation. It is an overhead valve design featuring two valves per cylinder with a camshaft centrally located in the engine block above the crankshaft, driven by a timing chain attached to toothed sprockets, with the camshaft in turn driving the distributor and oil pump. Valve actuation is by hydraulic lifters and pushrods to rocker arms (roller lifters in some models) in the cylinder heads; the lifter bore angle in the engine block is 45 degrees from the block centerline. A belt-driven radiator fan and water pump are located on the front of the engine block taking drive from the main pulley, as is the alternator. The cast iron engine block features a separate pressed steel non-stress bearing sump assembly with the crankshaft located within five main bearing journals secured with 2-bolt bearing caps; 4-bolt main bearing caps featured on later performance versions.[2][3]
Aftermarket Holden V8 alloy cylinder heads showing different valve layouts; pre-1988 (top) and post-1988 (bottom)
The cast iron cylinder heads are a cross-flow design with wedge-shaped combustion chambers and a single spark plug. In early versions of the engine the inlet and exhaust valves were arranged in a "mirrored" configuration around a longitudinal midpoint in each head i.e. I-E-I-E-E-I-E-I. The co-located exhaust valves in the two centre combustion chambers resulted in a "hot spot" making the heads prone to warping or cracking, especially in performance versions of the engine. For the fuel-injected 5000i version introduced in the 1988 VN Commodore, the cylinder heads were redesigned to a repeated I-E design (a similar layout was previously utilised for the HSV VL Group A SV) for all combustion chambers, delivering better heat distribution and thus greater reliability.[2][7]
Depending upon the application, induction was either carburettor or fuel-injection (multi-point or sequential, depending on the year). For the 1986 VL Commodore, the engine was modified to run on unleaded fuel which carried forth to all subsequent models.[2][4][7][8][9]
Applications
Initially offered in 4.1 and 5.0L; 252.8 and 307.8cuin (4,142 and 5,044cc) versions, the engines were intended to be offered as part of the 1968 Holden HK range, but the project ran behind schedule and instead became part of the 1969 HT model range. In the HT, the Holden V8 sold alongside the 350-cubic-inch (5.7L)Chevrolet Small-Block engine until 1974 with the introduction of the HJ series.[10]
5.0L; 307.8cuin (5,044cc) V8
The V8 engine also appeared from 1971 in the Statesman range of large size luxury cars which Holden established as a separate marque, replacing the Holden badged Brougham. In 1974, both the 253 and 308 engines were added to the Torana range for the first time in the LH series (after an aborted attempt by Holden Dealer Team boss Harry Firth to introduce the V8 to the smaller LJ Torana range in 1972 which was stopped by the Supercar scare). The engines were also offered on the LX model range introduced in 1976, but not the final UC range which appeared in 1978.
Both engine capacities were offered on the first VB Commodores which appeared in 1978. The 253 version was not available in the VK Commodore range, released in 1984, but continued in Holden WB commercials until their cessation in late 1984. In 1985, the special editions modified by Holden and their official after-market tuner, Peter Brock's HDT Special Vehicles, began introducing the 5.0L; 304.3cuin (4,987cc) version of the engine, created to slip underneath the 5,000cc (305cuin) engine capacity cut-off in Group Atouring car regulations, allowing Commodore competitors to run at a lower competition weight. This slight shrinking of the traditional Holden 308 saw the Group A Commodore's racing weight drop from 1,400 to 1,325kg (3,086 to 2,921lb). Due to the complex Group A regulations, this also allowed the racing cars to run bigger wheels and tyres without any drop in power. Indeed, the VK Commodore SS Group A was one of the fastest cars in the world of Group A racing when it hit the tracks in 1986.
HDT Special Vehicles also offered a more powerful version of the engine enlarged to 5.6L; 344.4cuin (5,643cc) in some of its VL models between 1986 and 1988, including the controversial Calais Director. This engine, making as much as 231kW (310hp), was an expensive option, particularly once Holden severed ties with HDT in February 1987, which drastically increased the prices of all HDT models, and consequently very few of the 5.6-litre motors were made. Bore and stroke is 102.4mm ×85.7mm (4.03in ×3.37in).
Fuel injection replaced the carburettors initially on the VL Commodore SS Group A SV, again with Group A touring car racing in mind, this car produced by Holden's new performance vehicle partner Holden Special Vehicles (HSV) in partnership with British-based Tom Walkinshaw Racing (TWR). While Group A disappeared after the VN model range, the fuel injected 5.0-litre; 304.3-cubic-inch (4,987cc) engine, often referred to by its nickname, The Iron Lion, was offered in Commodores until the VS III Commodore utility in 2000, although there were no longer V8 VS III utilities available for sale during the latter part of 2000.
HSV vehicles featured a variety of more powerful versions of the 5.0-litre, which were also available on regular V8 Holdens as part of the SV Enhanced package. Additionally, from 1994 with the VR series, a 5.7-litre; 349.8-cubic-inch (5,733cc) "stroker" was standard on the HSV GTS and optional on the HSV Senator, and later on the Statesman/Caprice-based Grange from that model's introduction in 1996.
↑ When converted to metric, although 253 cubic inches translates to 4.146 litres, this engine was always officially referred to by Holden as having a displacement of 4.2 litres, and not 4.1L as mathematical convention would dictate.
↑ More performance could be achieved from a 4-barrel carburettor, but the 253 was seen as the economy engine. Later ADR27A-compliant engines were fitted with a 4-barrel carburettor to compensate for the reduction in power resulting from the new regulations.[4]
Related Research Articles
The Holden Commodore is a series of automobiles that were sold by former Australian manufacturer Holden from 1978 to 2020. They were manufactured from 1978 to 2017 in Australia and from 1979 to 1990 in New Zealand, with production of the locally manufactured versions in Australia ending on 20 October 2017.
The Holden Monaro is a car that was manufactured by General Motors' Australian division Holden. It has a front-engine, rear-wheel-drive layout and was produced with a two-door coupé body from 1968 to 1975 and again from 2001 to 2006 and with a 4-door sedan body from 1973 to 1977.
Holden Special Vehicles (HSV) was the officially designated performance vehicle division for Holden. Established in 1987 and based in Clayton, Victoria, the privately owned company modified Holden models such as the standard wheelbase Commodore, long wheelbase Caprice and Statesman, and commercial Ute for domestic and export sale. HSV also modified other non-Holden cars within the General Motors lineup in low volumes.
The Holden Torana is a mid-sized car that was manufactured by Holden from 1967 to 1980. The name apparently comes from a word meaning "to fly" in an unconfirmed Aboriginal Australian language. The original HB series Torana was released in 1967 and was a four-cylinder compact vehicle closely based on the British Vauxhall Viva HB series of 1966–1970.
The Holden Caprice is a full-size car which was produced by Holden in Australia from 1990 to October 2017. The similar Holden Statesman, which was also introduced in 1990 as a model below the Caprice, was discontinued in September 2010. Between 1971 and 1984, Holden marketed their long-wheelbase sedans under the Statesman marque.
The Holden Kingswood is a full-size car that was developed and manufactured in Australia by Holden, from the beginning of the HK series in 1968 through to the conclusion of the WB series in 1985. Prior to 1968, the full-size Holden range of family cars comprised the Holden Standard, the Holden Special, and Holden Premier models. Initially, the HK range of models included the basic Holden Belmont, the Kingswood, and the luxury-oriented Holden Premier, all of which were manufactured in a choice of sedan and station wagon bodies. Commercial variants were offered in three types: coupé utility, panel van, and later from 1971, a heavy-duty Holden One Tonner cab chassis. The utility (ute) version was originally marketed in both Belmont and Kingswood configurations. However, after the Belmont name was deleted from commercials at the end of HQ in late 1974, the base model commercials were sold only with the "Holden" badge.
Super Sport, or SS, is the signature performance option package offered by the Chevrolet division of General Motors on a limited number of its vehicles. All SS models come with distinctive "SS" markings on their exterior. The SS package was first made available for the 1961 Impala. Some of the other models bearing the SS badge include the Camaro, Chevelle, El Camino, Impala, Monte Carlo, Nova and Chevrolet Pickup Trucks. Current SS models are produced by the GM Performance Division.
The Holden Dealer Team (HDT) was Holden's semi-official racing team from 1969 until 1986, primarily contesting Australian Touring Car events but also rallying, rallycross and Sports Sedan races during the 1970s. From 1980 the Holden Dealer Team, by then under the ownership of Peter Brock, diversified into producing modified road-going Commodores and other Holden cars for selected dealers via HDT Special Vehicles.
The Holden Commodore (VC) is a mid-size car that was produced by Holden, from 1980 to 1981. It was the second iteration of the first generation of the Holden Commodore.
The Holden Commodore (VN) is a full-size car that was produced by Holden from 1988 to 1991. It was the first iteration of the second generation of this Australian made model, which was previously a mid-size car, as well as the first Commodore available as a coupé utility. The new range included the luxury variants, Holden Berlina (VN) and Holden Calais (VN) and, from 1990, introduced the commercial Holden Utility (VG).
The Holden was a full-sized car produced by the company of the same name across 5 generations from 1948 until 1984. The Holden is also commonly referred to by their model designation and also the H Series. The Holden was introduced to be Australia's car, being the first full scale produced automobile exclusive to the country. Prior to which, General Motors Holden's Ltd. assembled imported CKD kits from overseas General Motors subsidiaries such as Chevrolet, Buick, Vauxhall and more. And the only other cars built in the country being Ford and Chrysler vehicle bodies fitted to imported chassis. The Holden was an instant success among Australians, being the first production car built solely for Australia's unique, rough roads.
The Holden Commodore (VL) is a mid-size car that was produced by Holden from 1986 to 1988. It was the final iteration of the first generation of the Holden Commodore and included the luxury variant, Holden Calais (VL). Between February 1986 and August 1988, 151,801 VL model Commodores were built.
The Holden Commodore (VK) is a mid-size car that was produced by Holden from 1984 to 1986. It was the fourth iteration of the first generation of the Holden Commodore and introduced the luxury variant, Holden Calais (VK) sedan.
Statesman is an automotive marque created in 1971 by the Australian General Motors subsidiary, Holden. Statesman vehicles were sold through Holden dealerships, and were initially based on the mainstream Holden HQ station wagon platform, thereby providing more interior room and generally more luxurious features than their Holden-branded sedan siblings. Production ceased with the last of the WB series cars in January 1985.
The Holden HQ series is a range of automobiles that was produced by Holden in Australia from 1971 to 1974. The HQ was released on 15 July 1971, replacing the Holden HG series. It was the first ground-up redesign of the Holden line since its original release in 1948, and included an all-new body, chassis, and suspension. The HQ was later developed into a series of successor models, finally ending production when the WB series was discontinued in 1985.
The SS was an option package for a range of Holden vehicles, featuring V8 engines, unique interiors, body kits, louder and higher flowing exhaust systems, that generally express a more aggressive and performance-centered feel over non-SS models. The SS badge is an acronym for "Super Sport", and was initially used in 1961 by General Motors, Holden's parent company.
The Holden straight-six motor is a series of straight-six engines that were produced by General Motors Holden at their Port Melbourne plant between 1948 and 1986. The initial Grey motor was so dubbed because of the colour of the cylinder block, later motors came in the form of a Red, Blue, Black, and the four-cylinder Starfire engine. These engines were fitted to all Australian designed Holdens of the same years, and the four-cylinder Starfire notably also found its way into the Toyota Corona (XT130). The Grey motor is a different engine from the others, while the Red, Blue, Black, and even the Starfire are all inter-related with many common parts and castings.
The Holden Utility (VG) is a full-size utility that was produced by the Australian manufacturer Holden from 1990 to 1991. It was based upon the Holden Commodore VN) released in 1988, and was the first utility in Holden's Commodore range. It was not badged as part of the Commodore range.
The Holden Special Vehicles VL SS Group A SV, aka. Walky, was a limited production homologation racecar produced by Holden's performance vehicles department, HSV in Clayton, Victoria. It was HSV's debut model after Holden cut ties with the proceeding Holden Dealership Team (HDT), and has become an icon of Australian automotive manufacturing. Based on the VL series Holden Commodore, the Commodore was shipped to HSV having only the Panorama Silver Paintwork and lack of some standard equipment to determine their future, HSV then removed any further pieces and built the car up to spec by hand, this process continued to be used by HSV until its closure in 2020, 33 years later. There were initially 500 Group As slated for production, but due to demand, was extended by 250 to a total of 750, that 250 vehicle extension proved to be a bad idea, after news of the upcoming VN Commodore-based Group A was leaked.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
Holden (General Motors)
