Small wind turbine

Last updated
Diagram of a small wind turbine and repeller. WindCompilationW1.jpg
Diagram of a small wind turbine and repeller.
A 1 kW micro windmill installed in the suburbs of Lahore, Pakistan. Micro WindMill.jpg
A 1 kW micro windmill installed in the suburbs of Lahore, Pakistan.
Small wind turbine power output Small wind turbine power output.png
Small wind turbine power output

Small wind turbines, also known as micro wind turbines or urban wind turbines, are wind turbines that generate electricity for small-scale use. These turbines are typically smaller than those found in wind farms. Small wind turbines often have passive yaw systems as opposed to active ones. They use a direct drive generator and use a tail fin to point into the wind, whereas larger turbines have geared powertrains that are actively pointed into the wind.

Contents

They usually produce between 500 W and 10 kW, with some as small as 50 W. The Canadian Wind Energy Association considers small wind turbines to be up to 300 kW, [1] while the IEC 61400 standard defines them as having a rotor area smaller than 200 m2 and generating voltage below 1000 Va.c. or 1500 Vd.c.

Design

Blades

Turbine blades for small-scale wind turbines are typically 1.5 to 3.5 metres (4 ft 11 in – 11 ft 6 in) in diameter and produce 0.5-10 kW at their optimal wind speed. [1] Most small wind turbines are horizontal-axis wind turbines, [2] but vertical axis wind turbines (VAWTs) may have benefits in maintenance and placement, although they are less efficient at converting wind to electricity. [3] To optimize efficiency, the tip speed ratio (the ratio of blade tip speed to wind speed) and lift-to-drag ratio should be kept at optimal levels.

Ground mounted small wind turbines are typically supported by four guy-wire, and a gin pole used to raise and lower the tower. Full mounting sets called "tower kits" are available. NRBO in 1988 - geograph.org.uk - 341596.jpg
Ground mounted small wind turbines are typically supported by four guy-wire, and a gin pole used to raise and lower the tower. Full mounting sets called "tower kits" are available.

A range of synthetic materials including carbon fiber reinforced polymers, nanocomposites, [4] and E-glass-polyester are available. [5] Although natural fibers are susceptible to quality variations, high moisture uptake and low thermal stability that make them undesirable for larger blades, small turbines can still take advantage of them. [6] Wood can be used, and the type of wood should be chosen based on availability, cost and growth time, average density, high stiffness, and breaking strain. Coatings are generally used to reduce moisture, and white enamel with primer has been found to be particularly effective. [7] Sitka spruce (used in propellers), and Douglas Fir have been used in turbine blades. [8] Nepal has used small blade turbines made of coated timber including Sal, Saur, Sisau, Uttish, Tuni, Okhar, pine, and lakuri wood. [9] Beyond wood, bamboo-based composites may also be used in both large and small wind turbines due to their low density and carbon sequestration ability—which makes bamboo materials environmentally friendly. Furthermore, relative to wood, bamboo has higher fracture toughness, higher strength, lower processing costs and fast growth rate. Ongoing materials developments include bamboo laminates using resins and hybrid bamboo carbon-fiber materials. [10] Hemp, flax, wood and bamboo are all candidate blade materials for small turbines. [11]

Placement

Wind turbines small enough to be held by a single steel pipe are often secured with scaffold base plate mounted to a concrete foundation. A hinged design allows easy lowering for maintenance. Scaffold Base Plate.jpg
Wind turbines small enough to be held by a single steel pipe are often secured with scaffold base plate mounted to a concrete foundation. A hinged design allows easy lowering for maintenance.

Small wind turbines must reach a certain wind speed, called the cut-in speed, to start generating electricity. This speed is usually around 4 metres per second (8.9 mph), [12] but some turbines can work at lower speeds. [13] To avoid obstacles, turbines are often placed on towers at least 9 m (30 ft) above anything within 150 m (490 ft). [14] Better locations for turbines are far from large upwind obstacles, as wind tunnel studies show significant negative effects from nearby obstacles can extend up to 80 times the obstacle's height downwind, [15] although this is an extreme case. Another option for placing a small turbine is using a model based on actual wind measurements to predict how nearby obstacles will affect local wind conditions at the potential turbine location, considering the size, shape, and distance to the obstacles. [16]

Small-scale rooftop turbines can be installed on a roof, but may face issues such as vibration and turbulence caused by the roof ledge, which can impact their power generation. These turbines often struggle to generate significant amounts of power, particularly in urban areas. [17]

Wiring

A high level wiring diagram for an off-grid hybrid wind/PV system. Micro Wind and Solar Wiring Diagram.svg
A high level wiring diagram for an off-grid hybrid wind/PV system.

The generators for small wind turbines are usually three-phase alternating current generators and the trend is to use the induction type, although some models utilize single-phase generators or direct current output. [18] [19]

After running the three phase AC wire through a slip ring and down to the receiving end, a three-phase rectifier is used to convert the AC to rectified DC for battery charging, especially in solar hybrid power systems. The rectifier should be mounted to a heat sink for cooling, with the option of adding a computer fan that is activated by a bimetal thermal switch for active cooling.

A three phase rectifier being used on a rooftop mounted urban wind turbine. Tridge rectifier.jpg
A three phase rectifier being used on a rooftop mounted urban wind turbine.

The DC end of the rectifier is then connected to the batteries. This connection should be as short as possible to avoid power losses, typically with a shunted digital wattmeter in between for monitoring. The batteries are then connected to a power inverter, which converts the power back to AC at a constant frequency for grid connectivity and end use.

Resistors being used as a diversion load which protect the turbine in the event of strong winds. Urbine resistor glog.jpg
Resistors being used as a diversion load which protect the turbine in the event of strong winds.

Dynamic braking is a technique used to regulate the speed of a turbine by discharging excess energy through a resistive load during high winds to prevent damage. The controller, activated when batteries reach a certain voltage, turns on the load using a solenoid or solid-state relay, the latter of which has the added benefit of "failing open". Proper tuning of the controller is important to prevent parasitic oscillations, which can be achieved through a delay function or using a stock PWM charge controller with a diversion function.

Cable resistant to UV radiation and temperature fluctuations, such as solar cable, should be used in cases where the wiring is exposed to the elements. The wire gauge across the whole system must be appropriate for the amount of current running through it. The resistance of the wire, which increases linearly with its length, should not create a voltage drop that is more than 2-5% of the total voltage drop.

Markets

Japan

In July 2012, a new feed-in tariff approved by Japanese Industry Minister Yukio Edano went into effect, promising to boost the country's production of wind and solar energy production. The country is aiming to increase renewable energy investment in part as a response to the Fukushima radiation crisis in March 2011. [20] The feed-in tariff applies to solar panels and small wind turbines and requires utilities to buy back electricity generated from renewable energy sources at government-established rates.

Small-scale wind power (turbines of less than 20 kW capacity) will be subsidized at least 57.75 JPY (about 0.74 USD per kwh). [21]

United Kingdom

Properties in rural or suburban parts of the UK can opt for a wind turbine with inverter to supplement local grid power. The UK's Microgeneration Certification Scheme (MCS) provides feed-in tariffs to owners of qualified small wind turbines. [22]

United States

A small-scale wind tower in rural Indiana, United States Wind-power-small-scale.jpg
A small-scale wind tower in rural Indiana, United States

In 2008, small wind turbines with capacities of 100 kW or less added a total of 17.3 MW of generating capacity in the US, according to the American Wind Energy Association (AWEA). This growth represented a 78% increase in the domestic market for small wind turbines. AWEA's "2009 Small Wind Global Market Study" attributed the increase to higher manufacturing volumes, thanks to private investment financing plant expansions, and rising electricity prices and public awareness of wind technologies driving residential sales.

In 2019, much of the US demand for small wind turbines was for power generation at remote locations, and for purposes of site assessment for large scale wind power installations. [23]

The US small wind industry also benefits from the global market, as it controls about half of the global market share. US manufacturers garnered $77 million of the $156 million that was spent throughout the world on small wind turbine installations. A total of 38.7 MW of small wind power capacity was installed globally in 2008. [24]

In the United States, residential wind turbines with outputs of 2–10 kW typically cost between US$12,000 and US$55,000 installed (US$6 per watt), although there are incentives and rebates available in 19 states that can reduce the purchase price for homeowners by up to 50 percent, to $3 per watt. [25] The US manufacturer Southwest Windpower estimates a turbine to pay for itself in energy savings in 5 to 12 years. [26] [27]

The dominant models on the market, especially in the United States, are horizontal-axis wind turbines.[ citation needed ]

To enable consumers to make an informed decision when purchasing a small wind turbine, a method for consumer labeling has been developed by IEA Wind Task 27 in collaboration with IEC TC88 MT2. In 2011 IEA Wind published a Recommended Practice, which describes the tests and procedures required to apply the label. [28]

Croatia

Hybrid system, 2400W windturbines, 4000W solar modules, island Zirje, Croatia Hybrid system, 2400W windturbines, 4000W solar modules, island Zirje, Croatia.jpg
Hybrid system, 2400W windturbines, 4000W solar modules, island Žirje, Croatia

Croatia is an ideal market for small wind turbines due to Mediterranean climate and numerous islands with no access to the electric grid. In winter months when there is less sun, but more wind, small wind turbines are a great addition to isolated renewable energy sites (GSM, stations, marinas etc.). That way solar and wind power provide consistent energy throughout the year.

Germany

In Germany the feed-in tariff for small wind turbines has always been the same as for large turbines. This is the main reason the small wind turbine sector in Germany developed slowly. In contrast, small photovoltaic systems in Germany benefited from a high feed-in tariff, at times above 50 Euro-Cent per kilowatt hour.

In August 2014 the German renewable energy law was adjusted, also affecting the feed-in tariffs for wind turbines. For the operation of a small wind turbine with a capacity below 50 kilowatt the tariff amounts to 8.5 Euro-Cent for a period of 20 years.

Due to the low feed-in tariff and high electricity prices in Germany, the economic operation of a small wind turbine depends on a large self-consumption rate of the electricity produced by the small wind turbine. Private households pay on average 35,7 Euro-Cent per kilowatt hour for electricity (19% VAT included). [30]

As part of the German renewable energy law 2014 a fee on self-consumed electricity was introduced in August 2014. The regulation does not apply to small power plants with a capacity below 10 kilowatt. With an amount of 1.87 Euro-Cents the fee is low. [31]

Manufacturing

DIY construction

Some hobbyists have built wind turbines from kits, sourced components, or from scratch. DIY wind turbines are usually smaller (rooftop) turbines of approximately 1 kW or less. [32] [33] [34] [35] These small wind turbines are usually tilt-up or fixed / guyed towers. [36] [37]

Do it yourself or DIY-wind turbine construction has been made popular by magazines such as OtherPower and Home Power. [38]

Organizations such as Practical Action have designed DIY wind turbines that can be easily built by communities in developing nations and are supplying concrete documents on how to do so. [39] [40]

Local manufacturing

Designs of DIY small wind turbines date back to the early 1970s, and were further developed by the back-to-the-land movement of the late 1970s in the United States and Europe. [41]

Locally manufactured small wind turbines, being small-scale, low-cost, socially-embedded, adoptive to local contexts and based on the open sharing of knowledge, have been framed under or associated with the perspectives of appropriate or intermediate technology, convivial technology, degrowth, open design and open manufacturing.

See also

Related Research Articles

<span class="mw-page-title-main">Wind power</span> Electrical power generation from wind

Wind power is the use of wind energy to generate useful work. Historically, wind power was used by sails, windmills and windpumps, but today it is mostly used to generate electricity. This article deals only with wind power for electricity generation. Today, wind power is generated almost completely with wind turbines, generally grouped into wind farms and connected to the electrical grid.

<span class="mw-page-title-main">Wind farm</span> Group of wind turbines

A wind farm or wind park, or wind power plant, is a group of wind turbines in the same location used to produce electricity. Wind farms vary in size from a small number of turbines to several hundred wind turbines covering an extensive area. Wind farms can be either onshore or offshore.

<span class="mw-page-title-main">Microgeneration</span> Small-scale heating and electric power creation

Microgeneration is the small-scale production of heat or electric power from a "low carbon source," as an alternative or supplement to traditional centralized grid-connected power.

<span class="mw-page-title-main">Renewable energy in Australia</span>

Renewable energy in Australia is based mainly on biomass, solar, wind, and hydro generation technologies. Over a third of all electricity generated in Australia is renewable energy, a proportion that is increasing in line with global trends, with a target to phase out coal power before 2040. In 2021 Australia overtook China in terms of renewable energy proportion, and as of 2024 has almost caught up with the European Union, but is still far behind Germany who overtook Australia in 2004. Wind and rooftop solar energy in particular have grown since 2010.

<span class="mw-page-title-main">Wind power in India</span>

Wind power generation capacity in India has significantly increased in recent years. As of 30 September 2024, the total installed wind power capacity was 47.36 gigawatts (GW). India has the fourth largest installed wind power capacity in the world. Wind power capacity is mainly spread across the southern, western, and northwestern states. The onshore wind power potential of India was assessed at 132 GW with minimum 32% CUF at 120 m above the local ground level (agl). Whereas, the estimated potential at minimum 25% CUF is 695 GW at 120 agl.

Financial incentives for photovoltaics are incentives offered to electricity consumers to install and operate solar-electric generating systems, also known as photovoltaics (PV).

<span class="mw-page-title-main">Solar power in the United Kingdom</span>

Solar power has a small but growing role in electricity production in the United Kingdom.

The American Wind Energy Association (AWEA) was a Washington, D.C.–based national trade association formed in 1974, representing wind power project developers, equipment suppliers, service providers, parts manufacturers, utilities, researchers, and others involved in the wind industry.

<span class="mw-page-title-main">Renewable energy in the United Kingdom</span>

Renewable energy in the United Kingdom contributes to production for electricity, heat, and transport.

<span class="mw-page-title-main">Community wind energy</span> Local ratepayer-owned air current power

Community wind projects are locally owned by farmers, investors, businesses, schools, utilities, or other public or private entities who utilize wind energy to support and reduce energy costs to the local community. The key feature is that local community members have a significant, direct financial stake in the project beyond land lease payments and tax revenue. Projects may be used for on-site power or to generate wholesale power for sale, usually on a commercial-scale greater than 100 kW.

<span class="mw-page-title-main">Wind turbine</span> Machine that converts wind energy into electrical energy

A wind turbine is a device that converts the kinetic energy of wind into electrical energy. As of 2020, hundreds of thousands of large turbines, in installations known as wind farms, were generating over 650 gigawatts of power, with 60 GW added each year. Wind turbines are an increasingly important source of intermittent renewable energy, and are used in many countries to lower energy costs and reduce reliance on fossil fuels. One study claimed that, as of 2009, wind had the "lowest relative greenhouse gas emissions, the least water consumption demands and the most favorable social impacts" compared to photovoltaic, hydro, geothermal, coal and gas energy sources.

The United States has the second largest electricity sector in the world, with 4,178 Terawatt-hours of generation in 2023. In 2023 the industry earned $491b in revenue at an average price of $0.127/kWh.

<span class="mw-page-title-main">Electricity sector in Sri Lanka</span>

The electricity sector in Sri Lanka has a national grid which is primarily powered by hydroelectric power and thermal power, with sources such as photovoltaics and wind power in early stages of deployment. Although potential sites are being identified, other power sources such as geothermal, nuclear, solar thermal and wave power are not used in the power generation process for the national grid.

Wind power in Indiana was limited to a few small water-pumping windmills on farms until 2008 with construction of Indiana's first utility-scale wind power facility, Goodland with a nameplate capacity of 130 MW. As of March of 2024, Indiana had a total of 2,743 MW of wind power capacity installed, ranking it 12th among U.S. states. Wind power was responsible for 4.8% of in-state electricity production in 2016.

IEC 61400 is an international standard published by the International Electrotechnical Commission (IEC) regarding wind turbines.

A feed-in tariff (FIT) is paid by energy suppliers in the United Kingdom if a property or organisation generates their own electricity using technology such as solar panels or wind turbines and feeds any surplus back to the grid. The FIT scheme was imposed on suppliers by the UK government, and applied to installations completed between July 2009 and March 2019.

<span class="mw-page-title-main">Hi-VAWT</span> Taiwanese renewable energy solutions provider

Hi-VAWT is a renewable energy solutions provider headquartered in Linkou District, New Taipei City, Taiwan. Hi-VAWT has installations in many countries/territories worldwide, and on every continent including Antarctica. The company also a member of Taiwan Wind Turbine Industry Association.

<span class="mw-page-title-main">Wind power in Thailand</span>

Wind power in Thailand amounted to an installed production capacity of 224.5 MW as of the end of 2014. Installed capacity was 112 MW at the end of 2012, with 111 MW added in 2013, and a minor amount added in 2014. This ranked Thailand 46th in the world by installed capacity as of 2015.

There is enormous potential for renewable energy in Kazakhstan, particularly from wind and small hydropower plants. The Republic of Kazakhstan has the potential to generate 10 times as much power as it currently needs from wind energy alone. But renewable energy accounts for just 0.6 percent of all power installations. Of that, 95 percent comes from small hydropower projects. The main barriers to investment in renewable energy are relatively high financing costs and an absence of uniform feed-in tariffs for electricity from renewable sources. The amount and duration of renewable energy feed-in tariffs are separately evaluated for each project, based on feasibility studies and project-specific generation costs. Power from wind, solar, biomass and water up to 35 MW, plus geothermal sources, are eligible for the tariff and transmission companies are required to purchase the energy of renewable energy producers. An amendment that introduces and clarifies technology-specific tariffs is now being prepared. It is expected to be adopted by Parliament by the end of 2014. In addition, the World Bank's Ease of Doing Business indicator shows the country to be relatively investor-friendly, ranking it in 10th position for investor protection.

<span class="mw-page-title-main">Renewable energy in South Africa</span>

Renewable energy in South Africa is energy generated in South Africa from renewable resources, those that naturally replenish themselves—such as sunlight, wind, tides, waves, rain, biomass, and geothermal heat. Renewable energy focuses on four core areas: electricity generation, air and water heating/cooling, transportation, and rural energy services. The energy sector in South Africa is an important component of global energy regimes due to the country's innovation and advances in renewable energy. South Africa's greenhouse gas (GHG) emissions is ranked as moderate and its per capita emission rate is higher than the global average. Energy demand within the country is expected to rise steadily and double by 2025.

References

  1. 1 2 Small Wind Turbine Purchasing Guide (PDF) (Report). Canadian Wind Energy Association. pp. 3–4. Archived from the original (PDF) on 2 March 2013. Retrieved 1 March 2016.
  2. ↑ Gipe, Paul. Wind energy basics: a guide to home- and community-scale wind energy systems. Chelsea Green Publishing, 2009. Accessed: 18 December 2010. ISBN   1-60358-030-1 ISBN   978-1-60358-030-4
  3. ↑ LuvSide. "5 Disadvantages of Vertical Axis Wind Turbine (VAWT) | The Windy Blog". www.luvside.de/en/. Retrieved 2021-03-11.
  4. ↑ Thirumalai, Durai Prabhakaran Raghavalu; Kale, Sandip A.; Prabakar, K., eds. (2015). Renewable Energy and Sustainable Development. ISBN   9781634634649.
  5. ↑ Sessarego, Matias; Wood, David (2015). "Multi-dimensional optimization of small wind turbine blades". Renewables: Wind, Water, and Solar. 2 (1): 9. Bibcode:2015RWWS....2....9S. doi: 10.1186/s40807-015-0009-x . ISSN   2198-994X.
  6. ↑ Kalagi, Ganesh; Patil, Rajashekar; Nayak, Narayan (2016). "Natural Fiber Reinforced Polymer Composite Materials for Wind Turbine Blade Applications" (PDF). International Journal of Scientific Development and Research. 1: 28–37.
  7. ↑ Sinha, Rakesh; Acharya, Parash; Freere, Peter; Sharma, Ranjan; Ghimire, Pramod; Mishnaevsky, Leon (2010). "Selection of Nepalese Timber for Small Wind Turbine Blade Construction". Wind Engineering. 34 (3): 263–276. Bibcode:2010WiEng..34..263S. doi:10.1260/0309-524X.34.3.263. ISSN   0309-524X. S2CID   110333693.
  8. ↑ Wood, David (2011), "Blade Design, Manufacture, and Testing", Small Wind Turbines, Green Energy and Technology, Springer London, pp. 119–143, doi:10.1007/978-1-84996-175-2_7, ISBN   9781849961745
  9. ↑ Mishnaevsky, Leon; Freere, Peter; Sinha, Rakesh; Acharya, Parash; Shrestha, Rakesh; Manandhar, Pushkar (2011). "Small wind turbines with timber blades for developing countries: Materials choice, development, installation and experiences". Renewable Energy. 36 (8): 2128–2138. Bibcode:2011REne...36.2128M. doi:10.1016/j.renene.2011.01.034. S2CID   110380390.
  10. ↑ Holmes, John W.; Brøndsted, Povl; Sørensen, Bent F.; Jiang, Zehui; Sun, Zhengjun; Chen, Xuhe (2009). "Development of a Bamboo-Based Composite as a Sustainable Green Material for Wind Turbine Blades". Wind Engineering. 33 (2): 197–210. Bibcode:2009WiEng..33..197H. doi:10.1260/030952409789141053. ISSN   0309-524X. S2CID   110079336.
  11. ↑ Bron̜dsted, Povl; Nijssen, Rogier P. L., eds. (2013). Advances in wind turbine blade design and materials. Oxford: Woodhead Publishing. ISBN   9780857097286. OCLC   864361386.
  12. ↑ Small Wind Turbine Purchasing Guide (PDF) (Report). Canadian Wind Energy Association. p. 6. Archived from the original (PDF) on 2 March 2013. Retrieved 1 March 2016.
  13. ↑ Luleva, Mila (28 October 2013). "Small-Scale "Dragonfly" Wind Turbine Works at Low Wind Speeds". Green Optimistic. Retrieved 18 September 2015.
  14. ↑ Hugh Piggott (6 January 2007). "Windspeed Measurement In The City". Scoraigwind.com. Retrieved 4 December 2011.
  15. ↑ "Wind tunnel measurements near an obstacle". Ntrs.nasa.gov. 15 October 2011. Retrieved 4 December 2011.
  16. ↑ Brunskill, Andrew W.; Lubitz, William David (4–7 January 2010). Written at Orlando, Florida. Development of an Empirical Obstacle Wake Model for Small Wind Turbine Micrositing. Session: WE-4: Wind Turbine Inflow, Siting, and Wind Farm Analysis. 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. Reston, VA: American Institute of Aeronautics and Astronautics. doi:10.2514/6.2010-828. AIAA 2010-828. Retrieved 2024-11-25. (For more details, see: Brunskill, Andrew William (March 2010). A Neural Network Based Wake Model for Small Wind Turbine Siting Near Obstacles (PDF) (M.Sc.A. thesis). Ontario, Canada: University of Guelph. ISBN   978-0-494-67483-3. MR67483. ProQuest   814731543 . Retrieved 2024-11-25.)
  17. ↑ Leake, Jonathan (2006-04-16). "Home wind turbines dealt killer blow". The Sunday Times. UK. Retrieved 2009-07-13.
  18. ↑ Forsyth, Trudy (20 May 2009). "Small Wind Technology" (PDF). National Renewable Energy Laboratory. Archived from the original (PDF) on 17 March 2013. Retrieved 20 September 2013.
  19. ↑ "Endurance E-3120-50 kW Wind Turbine from Endurance Wind Power". AZoNetwork. 13 May 2010. Retrieved 20 September 2013.
  20. ↑ "Japan approves renewable subsidies in shift from nuclear power". Reuters. 2012-06-18. Retrieved 18 June 2012.
  21. ↑ "Japan Approves Feed-in Tariffs". Reuters. 2012-06-22. Retrieved 22 June 2012.
  22. ↑ "Feed-In Tariffs Scheme (FITs)". MCS. Retrieved 29 December 2012.
  23. ↑ Casey, Tina (2019-09-19). "What's Up With The Micro Wind Turbines? They're Up!". CleanTechnica. Retrieved 2019-09-21.
  24. ↑ "EERE News: AWEA: U.S. Market for Small Wind Turbines Grew 78% in 2008". Apps1.eere.energy.gov. Retrieved 4 December 2011.
  25. ↑ Shevory, Kristina (13 December 2007). "Homespun Electricity, From the Wind". The New York Times. Retrieved 4 December 2011.
  26. ↑ "Southwest Windpower". Windenergy.com. Archived from the original on 11 January 2012. Retrieved 4 December 2011.
  27. ↑ "Wind Power for Commercial Projects: Case Studies". XZERES. Retrieved 18 September 2015.
  28. ↑ "IEA Wind Home Page". Ieawind.org. Retrieved 4 December 2011.
  29. ↑ "Kako i zašto ostvarujemo najbolje rezultate" (in Hungarian). Veneko. Retrieved 18 September 2015.
  30. ↑ "Index on the development of the electricity price for households in Germany in the years 1998 to 2023". de.statista.com. 27 September 2024. Retrieved 14 October 2024.
  31. ↑ "German Small Wind Turbine Portal". klein-windkraftanlagen.com. 15 June 2012. Retrieved 4 February 2015.
  32. ↑ "British Wind and Energy Agency's DIY wind turbines page". Bwea.com. Archived from the original on 4 December 2011. Retrieved 4 December 2011.
  33. ↑ "Common FAQs of wind turbine construction and info for proper building". Wind-turbine-24v.com. Retrieved 4 December 2011.
  34. ↑ "Overview of wind turbine construction and info for proper building". Otherpower.com. Retrieved 4 December 2011.
  35. ↑ Diy wind turbine 1kw. Youtube. 7 May 2015. Archived from the original on 2015-08-24. Retrieved 18 September 2015.
  36. ↑ "Smaller wind turbines usually of tilt-up or fixed design". Archived from the original on 1 October 2011. Retrieved 4 December 2011.
  37. ↑ "Modified Chispito Wind Turbine". Greenterrafirma.com. Retrieved 4 December 2011.
  38. ↑ "OtherPower and Home Power as popular diy microgeneration magazines" (PDF). Retrieved 4 December 2011.
  39. ↑ "Practical action producing info to construct DIY wind turbines for the developing world". Practicalaction.org. Retrieved 4 December 2011.
  40. ↑ "Basics on diy small scale windturbines and domestic power consumption" (PDF). Retrieved 4 December 2011.
  41. ↑ Latoufis, Kostas C.; Pazios, Thomas V.; Hatziargyriou, Nikos D. (March 2015). "Locally Manufactured Small Wind Turbines: Empowering communities for sustainable rural electrification". IEEE Electrification Magazine. 3 (1): 68–78. doi:10.1109/MELE.2014.2380073. ISSN   2325-5897. S2CID   868486.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.