Washington (steamboat 1851)

Last updated
Washington (Willamette river steamer) 1852 ad.jpg
1852 newspaper advertisement for Washington
History
NameWashington
Ownerknown: Alexander S. Murray; S.D. Hinsdale; Allan, McKinlay & Co
Route Sacramento River, Willamette River, Umpqua River, (reported: Coos Bay, Coquille River)
In service1851
Out of serviceDecember 12, 1857
FateDestroyed by boiler explosion near Scottsburg, Oregon.
General characteristics
Typeiron-hulled inland/coastal steamboat.
Tonnage20 tons
Length40 ft (12.2 m)
Beam8 ft (2.4 m)
Depth4 ft (1.2 m)
Installed power steam engine
Propulsion propeller

Washington was an early steamboat operated in the states of California and Oregon. Washington was built in California and was initially operated on the Sacramento River. In 1851, the steamer was purchased and brought on a ship to the Oregon Territory, where it was operated on the Willamette River until the summer of 1853. Washington was sold again, and then transferred to the Oregon coast, where it operated on the Umpqua River, on the Coquille River and on Coos Bay. Washington was able to operate for shorter distances over the open ocean along the Oregon coast. The steamer was wrecked by a boiler explosion in December 1857, near Scottsburg, O.T., on the Umpqua river.

Contents

Design

Washington had an iron hull and driven by twin propellers. [1] [2] It was capable of operating with a single propeller if one was damaged. [3] Washington was 40 feet long with a beam of 8 feet and a depth of hold of 4 feet. [4] Overall size of the Washington was 20 tons. [4] It was manufactured in Philadelphia and shipped out to the west coast of the United States. [4]

Propeller-driven vessels operated at a disadvantage on the Willamette. Sidewheel steamers did better in shallow water, as was often encountered on the upper Willamette and its navigable tributaries. [5] Propellers had to be submerged to furnish power, and there was always the potential in low water of striking obstruction on the river bottom, which happened to the Washington at least once, in September 1851, on the lower Willamette river. [3] [5] This was less of a danger to the side-wheelers. [5]

Operations in California

Washington first operated in California on the Sacramento River. There the Washington was the first steamboat to ascend the Sacramento River from Sacramento to the mouth of the Feather River. She subsequently made regular trips to the landing there called Vernon. [6] : 77 

Pioneer steamboat captain Alexander Sinclair Murray (1827-1914) bought the boat in 1851, and had it transported to Oregon on board the bark Success. [7] [8] [9] Although an oceangoing vessel, Success was able to proceed up to Oregon City in June, 1851, covering, it was claimed, most of the distance on the river under sail. [10] On June 5, 1851, the bark Success was reported to have arrived in the Columbia river, carrying two river boats, one a steamboat, and the other a propeller. [11]

Willamette River service

Operations on the upper Willamette

In early June 1851, Murray and some others investigated whether a small steamboat could be operated on the Tualatin river. [12] Murray had Washington launched above Willamette Falls at Canemah and worked on the Willamette River to the Yamhill River. [2] It was hoped that Washington could go as far up the Willamette as Corvallis, then known as Marysville. [1]

Washington's first run up the Yamhill was on June 6, 1851. [13] Washington remained this route for a time, seeking cargoes from the nearby wheat farms. [13] With Washington in service, there were now two steamboats running on the Willamette river above the falls. [14] Three steamboats were running below. [14] Two years previously there had been no steamers at all on the Willamette. [14] The main competition at this time against Washington was another propeller-driven steamer, the Hoosier . [13] Washington was advertised as running from Canemah to Champoeg, where the boat would meet a connecting stage coach line for travellers bound for Salem, Oregon.

On June 19, 1851, Captain Murray was reported to have "arrived with his iron, steam propeller" apparently the Washington. [15] Murray was reported to be confident of navigating to Salem at any time of the year. [15] The arrival of the new steamer was praised by the editor of the Oregon City weekly newspaper, Oregon Spectator as a sign of progress. [15]

On the morning of Thursday, June 26, 1851, Washington, with Capt. Murray in command, departed Oregon City on what was intend to be a run south to Corvallis, then known as Marysville. [10] As of June 26, 1851 in addition to the two operating boats on the upper Willamette, the Hoosier and the newly arrived Washington, there was another belonging to Captain Bissel, which was expected to be compete in four or five weeks. [10] The firm of Hedges & Barlow were building a new sidewheeler, the Canemah, which they expected to have running sometime in September. [10]

On its first trip, Washington went up the Yamhill River to Dayton, where the boat's crew was well received. [16] Washington remained at Dayton overnight, leaving the next morning for Salem, where they arrived at about 4:00 p.m on Friday, June 27. [16]

Washington was also welcomed at Salem, where the citizens fired off a saluting cannon, and made firewood and other supplies available to the steamer free of charge. [16] After about two hours at Salem, Washington proceeded further upstream to Cincinnati Landing, now known as Eola, where the boat was greeted by the proprietor of the place, A.C.R. Shaw. [16]

Cincinnati was a small landing 3 miles west of Salem, in Polk County, 200 yards up Rickreall Creek, which was then known as the La Creole River. [16] Washington under Captain Murray was the first steamboat to reach Eola. [13]

Advertisement for the steamer Washington, placed in the Oregon Spectator, July 22, 1851. Steamboat Washington ad 1851.jpg
Advertisement for the steamer Washington, placed in the Oregon Spectator, July 22, 1851.

To facilitate steamboat service, the citizens of Cincinnati Landing went to the extent of digging a canal from the Willamette to the La Creole River. [17] Washington was reported to have negotiated the canal without difficulty. [17]

Low water problems

Murray had placed Washington into regular service on the river on July 3, 1851. [18] In early July 1851, the river below the falls went down about 3.5 feet. [19] While navigation was reported to be unimpeded, there was just 18 inches of water on the bars above the falls. [19] Washington scrapped bottom in several places downriver from Salem, while the Hoosier was able to continue regular trips to Dayton. [19] The upper river proved to be too shallow for Washington, and freight could be found elsewhere for the vessel. [1]

Transfer to lower Willamette

In early August 1851, Washington was hauled around the falls to the lower Willamette river. [1] [5] [9] The river at that time was said to be unusually low, but still 10 or 15 inches above extreme low water. [20] The withdrawal of Washington left the Hoosier, for a time, as the only steamboat running on the upper Willamette. [20]

On the lower Willamette Washington ran between Portland, Oregon, and Oregon City, joining a small flotilla of steamboats which included Eagle, Blackhawk, Major Redding, Allan and Columbia. [1] [9] Washington was the largest of the vessels running on the lower river at that time. [3]

With very few people living in either Portland and Oregon City, competition was fierce. [1] As of November 18, 1851, Washington was running regularly between Oregon City and Portland, carrying "large quantities" of freight to the landing at Oregon City below the falls, to be portaged there and then shipped to points on the upper river. [21] [22] Service above the falls as far as Marysville was then conducted by two sternwheelers, Canemah and Multnomah, each making one trip a week. [22]

For a stretch of several days in mid-February, 1852, all steamboat service between Oregon City and Portland was suspended when both Washington and another iron-hulled propeller, the Eagle were taken off the route, apparently as a result of mechanical breakdowns. [23]

Return to upper Willamette

In spring 1853, Washington was taken back above the falls, back to the upper Willamette river, where it was operated only a few months, until July 1853. [7] Murray replaced Washington with a new wooden sidewheeler, the Portland. [8]

Sale to coastal interests

In July 1853, Washington was purchased for use on the Umpqua river by Allan, McKinlay & Co., an Oregon City concern which had a branch operation on the Umpqua. [9] Pioneer steamboat man William H. Troup (1828–1882), the father of steamboat captains James and Claud Troup, went with Washington as the vessel's engineer. [7]

Washington, then owned by Allan, McKinlay & Co, was rigged in schooner fashion for the voyage to the Umpqua. [24] In mid-August 1853, Washington departed Oregon City for the Umpqua, where, if it arrived safely, it was to be used as a tow boat. [24] No similar vessel was then in operation on that river. [24] On August 26, 1853, it was reported in Oregon City that Washington had arrived safely and undamaged at Scottsburg, despite having encountered some heavy weather on the way. [25]

Umpqua River service

Advertisement for steamer Washington service on the Umpqua river, 1854 Steamer Washington ad 1854.png
Advertisement for steamer Washington service on the Umpqua river, 1854

The head of navigation on the Umpqua River was a former Hudson's Bay Company outpost, called Scottsburg, O.T., In the mid-1850s, Scottsburg was the center of business and transport activity in southwestern Oregon. [26] The population in this area was increasing due to incoming settlers and mining activity. [26]

As of April 28, 1854, Washington made tri-weekly trips between Scottsburg and the mouth of the Umpqua River, departing from Allan, McKinlay & Company's wharf at Scottsburg on Mondays, Wednesdays and Fridays. [27] The company's owners advertised that "a good scow for the transportation of cattle is always in readiness." [27] One of Washington's owners was Capt. Sylvester Hinsdale (1824–1870), a former seaman and a merchant at Gardiner, Oregon, on the Umpqua River. [7]

On November 11, 1854, Washington was placed on a winter schedule, running, under Capt. J.U. Harris from the Allan, McKinlay & Co. wharf in lower Scottsburf every Saturday evening, carrying the U.S. mails, to Gardiner, Providence, Winchester Bay (then known as Umpqua City), and Pyramid Rock. [28] Washington returned to Scottsburg on Sunday morning, departing from Umpqua City at 8:00 a.m. [28]

The boat was advertised as being ready to "meet vessels at all other times, and receive freight and passengers for every point within the bounds of navigation on the Umpqua river. [28] Washington was still running on the winter schedule on February 24, 1855. [28]

Operations on the Coos and Coquille rivers

William H. Troup, engineer on the Washington William H. Troup (steamboat captain).jpg
William H. Troup, engineer on the Washington

Washington was operated on Coos Bay, again with Wm. H. Troup as engineer, and for a short time on the Coquille River. [1] [7] [29] Washington also ran on the open ocean in addition to riverine service.

On August 19, 1853, Washington departed Scottsburg, bound for Coos Bay. [30] Washington reached Umpqua City, now known as Winchester Bay, near the mouth of the river that same day. The next day, Saturday, August 19, Washington tried to cross the bar of the Umpqua, but the weather was too rough. [30] The next day however, Sunday, August 20, Washington was able to cross the bar and, despite bad weather during the voyage, reached and crossed the Coos Bay bar, and landed at the then newly founded town of Oregon. [30] Washington was able to use coal from the Coos Bay coal fields rather than wood as fuel for the boiler. [30]

Boiler explosion

Washington's career terminated with a boiler explosion in December 1857. [1] [7] About noon on Saturday, December 12, 1857, the boiler exploded on Washington, scalding five persons who were on board. [31] The extent of the injuries was not known at the time of the first report. [31] The boat was reported to have been left "a total wreck. [31] The incident occurred just downriver from Scottsburg. [1] [31] Washington was then the only steamer capable of transporting goods from Fort Umpqua to Scottsburg, [31]

Notes

  1. 1 2 3 4 5 6 7 8 9 Mills, Randall V. (1947). Sternwheelers up Columbia -- A Century of Steamboating in the Oregon Country. Lincoln NE: University of Nebraska. pp. 21, 95, 130, 203. ISBN   0-8032-5874-7. LCCN   77007161.
  2. 1 2 Affleck, Edward L. (2000). A Century of Paddlewheelers in the Pacific Northwest, the Yukon, and Alaska. Vancouver, BC: Alexander Nicholls Press. p. 28. ISBN   0-920034-08-X.
  3. 1 2 3 Schnebly, D.J., ed. (September 23, 1851). "The propeller Washington, on her downward trip …". Oregon Spectator . Vol. 6, no. 3. Oregon City, O.T.: Robert Moore. p. 2 col. 1.
  4. 1 2 3 "Appendix MM: Steamboats Out of Service". Report of the Chief of Engineers, U. S. Army: Improvement of Rivers and Harbors in Oregon and in Washington Territory. Vol. 2 pt. 3. Washington, DC: U.S. Government Printing Office. 1880. p. 2274.
  5. 1 2 3 4 Schnebly, D.J., ed. (August 5, 1851). "The steamer "Washington" has been taken from above the falls …". Oregon Spectator . Oregon City, O.T.: Robert Moore. p. 2 col. 2.
  6. ↑ Memorial And Biographical History Of Northern California: Containing a History of this Important Section of the Pacific Coast from the Earliest Period of Its Occupancy to the Present Time, Lewis Publishing Company, Chicago, 1891
  7. 1 2 3 4 5 6 Wright, E.W., ed. (1895). Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. pp.  33–34, 34 n.2, 43, 45, 185 n.10. LCCN   28001147.
  8. 1 2 Harry, De Witt; Morton, Emma Hyatt (January 4, 1920). "Fresh Water Salts Investigate Rivers of Romance". The Sunday Oregonian. Vol. XXXIX, no. 1. Portland, OR. Magazine section, p. 1 col.6.
  9. 1 2 3 4 Oregon Pioneer Association (1886). "1878 Annual Address by Hon. William Strong". Constitution and Quotations. Salem, OR. p. 22.{{cite book}}: CS1 maint: location missing publisher (link)
  10. 1 2 3 4 Schnedly, D.J., ed. (June 26, 1851). "Prospects Brightening". Oregon Spectator . Vol. 5, no. 42. Oregon City, O.T.: Robert Moore. p. 2 col. 2.
  11. ↑ Schnebly, D.J., ed. (June 5, 1851). "Two steamers are new in the Columbia on the bark Success ..." Oregon Spectator . Vol. 5, no. 39. Oregon City, O.T. p. 2 col. 1.
  12. ↑ Schnedly, D.J., ed. (June 12, 1851). "Several parties have been up exploring the Tualitin river …". Oregon Spectator . Vol. 5, no. 40. Oregon City, O.T.: Robert Moore. p. 2 col. 2.
  13. 1 2 3 4 Corning, Howard McKinley (1973). Willamette Landings -- Ghost Towns of the River (2nd ed.). Portland, OR: Oregon Historical Society. pp. 62, 132, 181. ISBN   0875950426.
  14. 1 2 3 Schnebly, D.J., ed. (July 3, 1851). "There were lying at our landing one day last wee, three steamers below the falls …". Oregon Spectator . Vol. 5, no. 43. Oregon City, O.T.: Robert Moore. p. 2 col. 1.
  15. 1 2 3 Schnebly, D.J., ed. (June 19, 1851). "Capt. Murray has arrived with his iron, steam propeller …". Oregon Spectator . Oregon City, O.T. p. 2 col. 1.
  16. 1 2 3 4 5 Schnebly, D.J., ed. (July 3, 1851). "The Washington, Capt. Murray owner, leaving Oregon City on Thursday last …". Oregon Spectator . Vol. 5, no. 43. Oregon City, O.T.: Robert Moore. p. 2 col. 1.
  17. 1 2 Schnebly, D.J. (ed.). "Internal Improvements". Oregon Spectator (letter). Vol. 5, no. 45. Oregon City, O.T.: Robert Moore. p. 2 col. 6.
  18. ↑ Schnebly, D.J., ed. (July 22, 1851). "Steam Navigation above the Falls". Oregon Spectator (advertisement). Vol. 7, no. 46. Oregon City, O.T.: Robert Moore. p. 3 col. 2.
  19. 1 2 3 Schnebly, D.J., ed. (July 10, 1851). "The river below the falls …". Oregon Spectator . Vol. 5, no. 45. Oregon City, O.T.: T.F. McElroy & C.W. Smith. p. 2 col. 6.
  20. 1 2 Schnebly, D.J., ed. (August 5, 1851). "The river above is said to be unusually low for this time of the year …". Oregon Spectator . Oregon City, O.T.: Robert Moore. p. 2 col. 2.
  21. ↑ Schnebly; Culver, eds. (November 18, 1851). "The propeller Washington has been running regularly …". Oregon Spectator . Oregon City, O.T. p. 2 col. 3.
  22. 1 2 Schnebly; Culver, eds. (December 30, 1851). "The steamers "Eagle" and "Washington" have been plying regularly for some time …". Oregon Spectator . Vol. 6, no. 17. Oregon City, O.T. p. 2 col. 3.
  23. ↑ Schnebly, D.J., ed. (February 24, 1852). "The propellers Washington and Eagle". Oregon Spectator . Vol. 6, no. 24. Oregon City, O.T.: Robert Moore. p. 1 col. 2.
  24. 1 2 3 Schnebly, D.J., ed. (August 19, 1853). "The steam propeller, Washington, having been fitted up in schooner style …". Oregon Spectator . Vol. 6, no. 27. Oregon City, O.T. p. 2 col. 5.
  25. ↑ Schnebly, D.J., ed. (August 26, 1853). "We learn from Messrs. Allan, McKinlay & Co. that the propeller Washington arrived …". Oregon Spectator . Vol. 6, no. 28. Oregon City, O.T. p. 2 col. 2.
  26. 1 2 Moser, Stephen A. (May 1976). Umpqua River Navigability Study. Salem, Oregon: State of Oregon, Division of State Lands. pp. 33–37.
  27. 1 2 Lyons, D.J., ed. (May 5, 1854). "The Steamer Washington". The Umpqua Weekly Gazette (advertisement). Vol. 1, no. 2. Scottsburg, O.T.: Beggs, Wm. J. p. 4 col. 5.
  28. 1 2 3 4 "Winter Arrangement: The Steamer Washington, Capt. J.U. Harris". The Umpqua Weekly Gazette (advertisement). Vol. I, no. 43. Scottsburg, O.T.: Boyd & Blakely. February 24, 1855. p. 4 col. 4.
  29. ↑ Timmen, Fritz (1973). Blow for the Landing -- A Hundred Years of Steam Navigation on the Waters of the West. Caldwell, ID: Caxton Printers. p. 200. ISBN   0-87004-221-1. LCCN   73150815.
  30. 1 2 3 4 "For the Oregon Spectator … From a letter dated Koose Bay, Lower Umpqua, Aug. 26, 1853". Oregon Spectator . Oregon City, O.T. September 16, 1853. p. 2 col. 1.
  31. 1 2 3 4 5 "From Oregon: Explosion of a Steamboat Boiler". Sacramento Daily Union. Vol. 14, no. 2, 099. James Anthony & Co. December 17, 1857. p. 1 col. 5.

Related Research Articles

<span class="mw-page-title-main">Steamboats of the Oregon Coast</span> 19th century steamboats in Oregon, US

The history of steamboats on the Oregon Coast begins in the late 19th century. Before the development of modern road and rail networks, transportation on the coast of Oregon was largely water-borne. This article focuses on inland steamboats and similar craft operating in, from south to north on the coast: Rogue River, Coquille River, Coos Bay, Umpqua River, Siuslaw Bay, Yaquina Bay, Siletz River, and Tillamook Bay. The boats were all very small, nothing like the big sternwheelers and propeller boats that ran on the Columbia River or Puget Sound. There were many of them, however, and they came to be known as the "mosquito fleet."

<i>Altona</i> (sternwheeler)

The steamship Altona operated from 1890 to 1907 on the Willamette River in the U.S. state of Oregon. In 1907, she was transferred to Alaska.

<i>Gazelle</i> (1854 sidewheeler) American ship

Gazelle was an early sidewheeler on the Willamette River in what is now the U.S. state of Oregon. She did not operate long, suffering a catastrophic boiler explosion on April 8, 1854, less than a month after her trial voyage. This was the worst such explosion ever to occur in the Pacific Northwest states. The wrecked Gazelle was rebuilt and operated for a few years, first briefly as the unpowered barge Sarah Hoyt and then, with boilers installed, as the steamer Señorita. A victim of the explosion was D.P. Fuller, age 28, who is buried in Lone Fir Cemetery in Portland, Oregon.

<i>Multnomah</i> (1851 sidewheeler)

The Multnomah was one of the first steamboats to operate on the Willamette and Yamhill rivers. This vessel should not be confused with the Multnomah, a steamboat built in Portland, Oregon in 1885, which was larger and of a much different design.

<i>Shoalwater</i> (sidewheeler 1852)

The steamboat Shoalwater was the sixth steamer to operate on the upper Willamette River, which refers to the part of the river above Willamette Falls at Oregon City. In a short career of six years, Shoalwater was renamedFenix, Franklin, and Minnie Holmes. Shoalwater was the first steamboat in Oregon to suffer a boiler explosion, although no fatalities resulted.

<i>Elwood</i> (sternwheeler) Steamboat

Elwood was a sternwheel steamboat which was built to operate on the Willamette River, in Oregon, but which later operated on the Lewis River in Washington, the Stikine River in Canada, and on Puget Sound. The name of this vessel is sometimes seen spelled "Ellwood". Elwood is probably best known for an incident in 1893, when it was approaching the Madison Street Bridge over the Willamette River in Portland, Oregon. The bridge swung open to allow the steamer to pass. However, a streetcar coming in from the east end of the bridge failed to notice the bridge was open, and ran off into the river in the Madison Street Bridge disaster.

<i>Jennie Clark</i> American steamboat

Jennie Clark, also seen spelled Jenny Clark, was the first sternwheel-driven steamboat to operate on the rivers of the Pacific Northwest, including British Columbia. This vessel was commonly known as the Jennie when it was in service. The design of the Jennie Clark set a pattern for all future sternwheel steamboats built in the Pacific Northwest and in British Columbia.

<i>Portland</i> (sidewheeler 1853)

Portland was a side wheel steamer built at Portland, Oregon in the summer of 1853. This vessel was chiefly remembered for its dramatic destruction in 1857 by being washed over Willamette Falls, an incident which killed its captain and a deckhand. The death of the captain, Arthur Jamieson, was one of at least four brothers, all steamboat officers, who were killed in three separate steamboating accidents occurring between 1857 and 1861 in Oregon and in British Columbia.

<i>Black Hawk</i> (steamboat)

Black Hawk was one of three small iron-propeller driven steamboats manufactured in Philadelphia in about 1850 and shipped to the west coast of United States to be placed in river service. The other boats were Eagle and Major Redding. These boats were some of the earliest steamers to operate on the Willamette and Columbia rivers. They could carry about 12 passengers and perhaps a ton of cargo. The boats had to be small to make the run to Oregon City, which passed through the Clackamas rapids a short distance downriver from the town.

<i>Wallamet</i> (1853 sidewheeler)

Wallamet was a sidewheel-driven steamboat that operated on the Willamette and Columbia rivers in Oregon and later on the Sacramento and San Joaquin rivers in California. Built in a Mississippi river style that was not suited to the conditions of these rivers, and suffering from construction defects, Wallamet was not a financially successful vessel. The name of this vessel is often seen spelled as Willamette.

<i>Three Sisters</i> (sternwheeler)

Three Sisters was a sternwheel-driven steamboat that operated on the Willamette River from 1886 to 1896. The steamer was built as an extreme shallow-draft vessel, to permit it to reach points on the upper Willamette river such as Corvallis, Harrisburg and Eugene, Oregon during summer months when water levels in the river were generally low. The vessel was also known for having been washed up on a county road in Oregon during a flood in 1890.

<i>Unio</i> (sternwheeler)

Unio was a small sternwheel-driven steamboat which operated on the Willamette and Yamhill rivers from 1861 to 1869. This vessel is primarily remembered for its having been named Unio when built in 1861, in the first year of the American Civil War, and then having the name completed, to Union, by a new, staunchly pro-Union owner, James D. Miller. Union appears to have sunk in 1869, been salvaged, and then dismantled, with the machinery going to a new steamer then being built for service on the Umpqua River.

<span class="mw-page-title-main">People's Transportation Company</span> Defunct steamboat company that operated in Oregon, United States

The People's Transportation Company operated steamboats on the Willamette River and its tributaries, the Yamhill and Tualatin rivers, in the State of Oregon from 1862 to 1871. For a brief time this company operated steamers on the Columbia River, and for about two months in 1864, the company operated a small steamer on the Clackamas River.

<i>James Clinton</i> (sternwheeler)

James Clinton was a steamboat which operated on the upper Willamette River from 1856 to 1861. Although the Clinton was said to have been "not a very good boat.", it was the first steamer ever to reach Eugene, Oregon. James Clinton was destroyed in April 1861, when a large fire broke out at Linn City, Oregon in a shoreside structure near to where the vessel was moored.

<i>Oregon</i> (sidewheeler 1852)

Oregon was a side-wheel driven steamboat that operated on the Willamette River in the state of Oregon from 1852 to 1854. The steamer was not economically successful and became a total loss by sinking after a short career.

<i>Alice</i> (sternwheeler)

Alice was a stern-wheel driven steamboat that operated on the Willamette and Columbia rivers in the 1870s and 1880s. Alice was the largest vessel built above Willamette Falls and was considered in its day to be the "Queen of the River". This steamer was rebuilt after near-destruction in a fire at Oregon City, Oregon in May 1873. In 1876, it was withdrawn from the upper Willamette River and transferred to the Columbia River, where it was worked as a towboat moving ocean-going ships to and from Portland and Astoria, Oregon, near the mouth of the Columbia River.

<i>Wenat</i> (sternwheeler)

Wenat was a stern-wheel steamboat that, under the name Swan, was built and operated, briefly, on the Tualatin River, in the state of Oregon. In 1858, Swan was sold, moved to the lower Willamette River, renamed Cowlitz, and placed on a route between Portland, Oregon the Cowlitz River.

<i>Dayton</i> (sternwheeler)

Dayton was a steamboat which operated on the Willamette and Columbia rivers from 1868 to 1881. Dayton operated on the Willamette from 1868 to 1876, mostly upriver from Willamette Falls, including a route on the Yamhill River to Dayton, Oregon, after which the steamer was named. From 1876 to 1881, Dayton was employed on a run from Portland to Monticello, W.T., which was located on the site of what is now Longview, Washington.

<i>Occident</i> (sternwheeler)

Occident was a steamer that operated on the Willamette River and occasionally its tributary, the Santiam River from 1875 to about 1890. Occident was designed primarily for freight work, and did not have passenger accommodations. This Occident should not be confused with the smaller steam launch Occident, apparently propeller-driven, which operated out of Astoria, Oregon in the 1890s.

<i>Relief</i> (1906 sternwheeler)

Relief was a stern-wheel steamboat that operated on the Columbia and Willamette rivers and their tributaries from 1906 to 1931. Relief had been originally built in 1902, on the Columbia at Blalock, Oregon, in Gilliam County, and launched and operated as Columbia, a much smaller vessel. Relief was used primarily as a freight carrier, first for about ten years in the Inland Empire region of Oregon and Washington, hauling wheat and fruit, and after that was operated on the lower Columbia river.

References

Books

On line historic newspaper collections

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.