 | This article needs additional citations for verification .(February 2020) |
The Yamaha Niken is a 845 cc tilting three-wheeler motorcycle, manufactured since 2018 by Yamaha Motor and sold worldwide.
| | This article needs additional citations for verification .(February 2020) |
The Yamaha Niken is a 845 cc tilting three-wheeler motorcycle, manufactured since 2018 by Yamaha Motor and sold worldwide.
The Niken is a commercial version of the concept bike "MWT-9" announced by Yamaha in 2015. As part of Yamaha's LMW line of bikes - Leaning Multi Wheel - the Tricity with 125cc had previously appeared in 2014. The basic concept is that the two front wheels move in conjunction with each other when the vehicle body is tilted, while the body can be moved like a normal motorcycle.
The name Niken is a coined word meaning "two swords", referring to the dynamic movement of the front two wheels like a sword master's two blades.
The development concept was called "New Type of Agility & Controllability".
The model was shown as a concept vehicle at the 2015 Tokyo Motor Show, and launched at the 2017 show. It was announced for release in Japan on September 13, 2018, and order reception began on the same day.
Vehicle equipment: [1]
Water-cooled in-line three-cylinder engine, mechanically identical to the sports naked Yamaha MT-09 and Tracer 900, though the gear ratio and the ECU setup were changed.
The Niken arranges the front fork outboard of the front wheels, in order to allow a bank angle of 45 degrees allowing for higher corner speeds than the Tricity, which has the front fork inboard of the front wheels. The spacing of the front wheels is 410 mm. The newly developed steering mechanism achieves operability and steering very close to that of a normal motorcycle.
The front suspension uses parallel quadrilateral arms to support the cantilevered suspension. It is mounted outboard of the wheels to allow maximum lean and comprises two upside-down fork legs per side – a 43mm rear leg with adjustable preload and damping, and a 41mm front leg which holds the assembly in alignment. Steering forces are applied via a separate group of tie rods and linkages, including offset steering knuckles. They realize the Ackermann steering geometry, similar to most cars in that during a turn the inner wheel turns progressively more than the outside, as it traces a smaller radius in each corner. Stub axles on each side carry cast aluminum wheels of 15 inches size, using 120/70-15 tires. [2]
The additional mechanics lead to 263 kg weight, around 70 kg more than the classical MT-09 motorcycle with the same basic engine. [3]
According to the Japanese Road Traffic Law, as with the Tricity, the Niken falls under the requirements for three-wheeled vehicles specified in the notification by the Prime Minister and is classified as a Specific Motorcycle, more precisely a Specific Large Motorcycle. This type requires a Large Motorcycle driving license.
The application of the Road Traffic Act and the Road Act is equivalent to that of motorcycles, and the legal maximum speed is 60 km / h on general roads and 100 km / h on national highways. According to the Road Transport Vehicles Act, it is treated as a "motorcycle with sidecar" and is classified as a two-wheeled small car because of its displacement of 400cc or more. Therefore, it is subject to the automobile inspection registration system (vehicle inspection).
An anti-lock braking system (ABS) is a safety anti-skid braking system used on aircraft and on land vehicles, such as cars, motorcycles, trucks, and buses. ABS operates by preventing the wheels from locking up during braking, thereby maintaining tractive contact with the road surface and allowing the driver to maintain more control over the vehicle.
A tricycle, sometimes abbreviated to trike, is a human-powered three-wheeled vehicle.
Yamaha Motor Co., Ltd. is a Japanese mobility manufacturer that produces motorcycles, motorboats, outboard motors, and other motorized products. The company was established in the year 1955 upon separation from Nippon Gakki Co., Ltd. and is headquartered in Iwata, Shizuoka, Japan. The company conducts development, production and marketing operations through 109 consolidated subsidiaries as of 2012.
Countersteering is used by single-track vehicle operators, such as cyclists and motorcyclists, to initiate a turn toward a given direction by momentarily steering counter to the desired direction. To negotiate a turn successfully, the combined center of mass of the rider and the single-track vehicle must first be leaned in the direction of the turn, and steering briefly in the opposite direction causes that lean. The rider's action of countersteering is sometimes referred to as "giving a steering command".
A three-wheeler is a vehicle with three wheels. Some are motorized tricycles, which may be legally classed as motorcycles, while others are tricycles without a motor, some of which are human-powered vehicles and animal-powered vehicles.
A tilting three-wheeler, tilting trike, leaning trike, or even just tilter, is a three-wheeled vehicle and usually a narrow-track vehicle whose body and or wheels tilt in the direction of a turn. Such vehicles can corner without rolling over despite having a narrow axle track because they can balance some or all of the roll moment caused by centripetal acceleration with an opposite roll moment caused by gravity, as bicycles and motorcycles do. This also reduces the lateral acceleration experienced by the rider, which some find more comfortable than the alternative. The narrow profile can result in reduced aerodynamic drag and increased fuel efficiency. These types of vehicles have also been described as "man-wide vehicles" (MWV).
The Yamaha XS650 is a mid-size motorcycle made by Yamaha Motor Company. The standard model was introduced in October 1969,and produced through 1979. The "Special" cruiser model was introduced in 1978 and produced through 1985. The XS650 began with the 1955 Hosk SOHC 500 twin. After about 10 years of producing 500 twin, Hosk engineers designed a 650 cc twin. Later the Hosk company was acquired by Showa Corporation, and in 1960 Yamaha had bought Showa with Hosk's early design of 650 cc twin.
The six main types of motorcycles are generally recognized as standard, cruiser, touring, sports, off-road, and dual-purpose. Sport touring is sometimes recognized as a seventh category or integrated with the touring category.
Hub-center steering (HCS) is one of several different types of front-end suspension/steering mechanisms used in motorcycles and cargo bicycles. Hub-center steering is characterized by the steering pivot points being inside the hub of the wheel, rather than above the wheel in the headstock as in the traditional layout. Most hub-center arrangements employ a swingarm that extends from the bottom of the engine/frame to the center of the front wheel.
Bicycle and motorcycle dynamics is the science of the motion of bicycles and motorcycles and their components, due to the forces acting on them. Dynamics falls under a branch of physics known as classical mechanics. Bike motions of interest include balancing, steering, braking, accelerating, suspension activation, and vibration. The study of these motions began in the late 19th century and continues today.
A motorcycle's suspension serves a dual purpose: contributing to the vehicle's handling and braking, and providing safety and comfort by keeping the vehicle's passengers comfortably isolated from road noise, bumps and vibrations.
A motorcycle fork connects a motorcycle's front wheel and axle to its frame, typically via a yoke, also known as a triple clamp, which consists of an upper yoke joined to a lower yoke via a steering stem, a shaft that runs through the steering head, creating the steering axis. Most forks incorporate the front suspension and front brake, and allow the front wheel to rotate about the steering axis so that the bike may be steered. Most handlebars attach to the top clamp in various ways, while clip-on handlebars clamp to the fork tubes, either just above or just below the upper triple clamp.
Bicycle and motorcycle geometry is the collection of key measurements that define a particular bike configuration. Primary among these are wheelbase, steering axis angle, fork offset, and trail. These parameters have a major influence on how a bike handles.
Originally designed in 1966 by Leonard R Jordan Jr, the steering damper or steering stabiliser is a damping device designed to inhibit an undesirable, uncontrolled movement or oscillation of a vehicle steering mechanism, a phenomenon known in motorcycling as the death wobble. The stabilizer absorbs unwanted energy in the side to side motion allowing the forks and shocks to work properly. Many things can cause a motorcycle chassis to get upset such as slamming on brakes, rough road, and lastly improper setup. An upset chassis can be a great deal of danger for the rider often times resulting in a crash. A steering stabilizer slows those movements down resulting in the rider feeling more comfortable on the motorcycle.
Motorcycle components and systems for a motorcycle are engineered, manufactured, and assembled in order to produce motorcycle models with the desired performance, aesthetics, and cost. The key components of modern motorcycles are presented below.
The Yamaha TX500 is a two-cylinder standard motorcycle built by Yamaha and sold in 1973 and 1974. Early models closely resembled the Triumph Bonneville in style. In 1975 the bike was renamed XS500 and then continued to be updated until 1978 when sales ended in the USA. In Europe, the model was available through 1980.
The Yamaha Tricity is a tilting three-wheeler motor scooter made by Yamaha Motor Company. It is part of Yamaha's LMW offering along with the Niken.
Motorcycle braking systems have varied throughout time, as motorcycles evolved from bicycles with an engine attached, to the 220 mph (350 km/h) prototype motorcycles seen racing in MotoGP. Most systems work by converting kinetic energy into thermal energy (heat) by friction. On motorcycles, approximately 70% of the braking effort is performed by the front brake. This however can vary for individual motorcycles; longer-wheelbase types having more weight biased rearward, such as cruisers and tourers, can have a`greater effort applied by the rear brake. In contrast, sports bikes with a shorter wheelbase and more vertical fork geometry can tolerate higher front braking loads. For these reasons, motorcycles tend to have a vastly more powerful front brake compared to the rear.
A narrow-track vehicle is a vehicle that leaves a narrow ground track as it moves forward. Narrow-track vehicles may have lateral stability when stationary but usually lean into turns to prevent falling towards the outside.
| Standard | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sport | |||||||||||||
| MotoGP | |||||||||||||
| Touring / Sport touring | |||||||||||||
| Power cruiser | |||||||||||||
| Cruisers |
| ||||||||||||
| Supermoto | |||||||||||||
| Dual-sport / Enduro / Off-road | |||||||||||||
| Agricultural | |||||||||||||
| Motocross | |||||||||||||
| Scooter | |||||||||||||
| Tricycle | |||||||||||||
| First models | |||||||||||||
