AAUSat-3

Last updated

AAUSat-3
AAUSAT3-FM.jpg
AAUSat-3 flight model
NamesAAUSAT3
Aalborg University CubeSat-3
Mission type Technology demonstration
Operator Aalborg University
COSPAR ID 2013-009B
SATCAT no. 39087
Website space.aau.dk/aausat3
Mission duration1 month (planned)
18 months (achieved)
Spacecraft properties
SpacecraftAalborg University CubeSat-3
Spacecraft type1U CubeSat
Bus CubeSat
Manufacturer Aalborg University
Launch mass0.8 kg (1.8 lb)
Dimensions10 × 10 × 11.3 cm (3.9 × 3.9 × 4.4 in)
Start of mission
Launch date25 February 2013, 12:31 UTC [1]
Rocket Polar Satellite Launch Vehicle (PSLV-CA) (PSLV-C20)
Launch site Satish Dhawan Space Centre, First Launch Pad (FLP)
Contractor Indian Space Research Organisation
Entered serviceMarch 2013
End of mission
Deactivated1 October 2014
Last contact17 September 2014
Orbital parameters
Reference system Geocentric orbit [2]
Regime Low Earth orbit
Perigee altitude 775 km (482 mi)
Apogee altitude 793 km (493 mi)
Inclination 98.62°
Period 100.60 minutes
Instruments
Automatic Identification System (AIS)
←  AAUSat-2
AAUSat-5  →
 

AAUSat-3, (Aalborg University CubeSat-3), [3] is the third CubeSat built and operated by students from the Aalborg University in Denmark. It was launched on 25 February 2013 from the Satish Dhawan Space Centre in India on a Polar Satellite Launch Vehicle (PSLV) launch vehicle (PSLV-C20). AAUSat-3 carries two Automatic Identification System (AIS-1 and AIS-2)) receivers as the main payload.

Contents

Educational objective

The primary purpose of satellite construction at University of Aalborg is to give the students engineering experience beyond what is normally achieved within a master's degree program. The design, implementation, and manufacturing were carried out by students, with only two exceptions: the manufacturing of the mechanical structure (carried out by the department workshop in alu7075), and the raw non-mounted PCBs. The project is funded mainly by Aalborg University and by Danish Maritime Safety Administration (DaMSA ), along with other sponsors. [3]

Scientific objective

The purpose of the satellite project was to find out if it was possible to receive Automatic Identification System (AIS) signals from a 1U CubeSat. [3]

The spacecraft was designed to operate on a non-centralized basis so it would be able to continue functioning even when certain subsystems failed. It carried two automated identification system (AIS) receivers - one based on SDR principle. The images recorded by the satellite were later transmitted to the ground station located at Aalborg University, from which they were made accessible for the general public. [4]

History

Student satellite activities at Aalborg University (AAU) started in 2003 as a result of AAU's involvement in the first pure Danish research satellite, Ørsted, which was successfully launched in 1999. AAUSat-3's predecessors were AAU CubeSat (launched in 2003), and AAUSat-2 (launched in 2008). Students from AAU also participated in SSETI EXPRESS (launched in 2005), a student satellite initiative by European Space Agency (ESA) Education. The construction of AAUSat-3 began in the fall of 2007. [3]

The satellite prototype was tested on a stratospheric balloon flight in October 2009 as part the BEXUS (Balloon Experiments for University Students) program, which allows European students to test scientific experiments in high altitude conditions. The balloon test served as an excellent opportunity to test the AIS receivers with an extended field of view (FOV) and to acquire realistic samples for further development of the final payload receivers. The payload on BEXUS was called NAVIS (North Atlantic Vessel Identification System). [3]

Operations

8124 AIS messages received in 11 hours on 8 March 2013. Aisfromaausat3-8march2013.png
8124 AIS messages received in 11 hours on 8 March 2013.

AAUSat-3 was launched on 25 February 2013 on PSLV-C20. Operations were a success. 9,000 AIS messages were received on a daily basis and downloaded to the mission control center (MCC), located in Aalborg, Denmark. All subsystems were tested and running. The first 100 days of operation were very successful. No degradation of the satellite was observed, all subsystems were working, and the primary payload – an AIS receiver – was working correctly. [3]

Two critical situations occurred during the first 100 days:

28 February 2013 at 06:08: The last message for some days was received. During the previous 24 hours, battery voltage was decreasing, and temperature readings indicated that AAUSat-3 was steady pointing the side without solar cells towards the Sun. During the last pass over Aalborg, it was observed that battery voltage was slowly decreasing. The situation was discussed and analyzed during the day, and it was decided to instruct AAUSAT3 on all upcoming passes to switch off beacon mode because it was using power. No further attempt was taken to make contact during the weekend in order to preserve and recharge the satellite's battery. All passes were supervised. There was total silence until 4 March at 17:52 where the ground station in Aalborg requestes and received a beacon. The beacon showed an uptime of 1 day 19 hours, that everything was working, and that more than 7,000 AIS messages had been received. Everything went back to normal. The requested beacon also showed a high number of reboots, possibly due to low battery voltage. Due to this event, AAUSat-3 was set to tumble slowly – 2 rotations for every 100-minute orbit – to avoid a repetition of the problem.

24 May 2013: The power system (EPS) on AAUSAT3 rejected multi-frame communication packages from the ground. During four passes (500 minutes), the students analyzed the situation and inspected the C source for the EPS server, and a solution was found. A new package was sent to AAUSat-3, and normal EPS operation was re-established. During the event, the rest of the satellite – due to the decentralized design – was working. During the first 100 days, close to 800,000 AIS packages were received and downloaded.

10–11 June 2013: Two new software images for the SDR AIS receiver (AIS-2) were uploaded. It took approximately 1.5 paths to upload a full AIS receiver image. The satellite showed improvement and was newly capable of sampling and decoding in real time. First metrics showed a capacity of around 6,000 AIS messages per hour on average.

25 February 2014: One year up in space. AAUSAT3 was fully functioning, and AIS measurements were done on a regular basis. A ground station was established at Thule (Qaanaaq), Greenland, for extended download capacity. Energy production was stable but low, so the mission was interleaved with hours or days for charging batteries. New uploaded algorithms showed reception of approximately 8,000 messages per hour and real-time performance, which meant that decoding took less time than sampling and was carried out in parallel. Due to the ground station at Thule, it was possible to carry out real-time supervision, measuring and downloading at the same time. So only a few seconds after detection, the information was available in Aalborg at the MCC.

17 September 2014: The last message was received from the satellite. [3]

1 October 2014: The project at AAU declared the end of the AAUSat-3 mission due to battery problems (continuous decline in power production). The project is grateful for the experience gained throughout the mission.

Satellite subsystem strategy

AAUSat-3 was based on a decentralized concept with no dedicated master. The idea behind this approach was to achieve a modular satellite that, in many cases, would be able to function even when certain subsystems failed. For that reason, the must-have subsystems (EPS and COM) were designed to be simple and robust, whereas subsystems like AIS-2 were by necessity more complex, with a concomitant higher failure rate. [3]

The power system (EPS) acts as intelligent supervisor and watchdog. AAUSat-3 consists of several sub-systems:

EPSElectronic Power Supplyat90can1288 MHz FreeRTOS 32kB add RAM
COMCommunication Moduleat90can12816 MHz FreeRTOS 32 kB added RAMADF702x radio
ADCS1Attitude Determination and Control 1at90can1288 MHz FreeRTOS 32 kB added RAMdetumbling
ADCS2Attitude Determination and Control 2arm 7x0 MHz FreeRTOS xx kB added RAMdetermination and control
AIS1Automatic Identification Systemat90can1288 MHz FreeRTOS 32 kB added RAMADF702x for AIS receive
AIS2Automatic Identification SystemBF537XXX MHz μClinux ADF702x for AIS receiveReceive all channels simultaneously
LOGOnboard logging system FreeRTOS
FPFlightPlanner FreeRTOS

On the ground segment, there were:

All internal and satellite-to-ground communication was carried out using CSP protocol.

Technical specifications

The technical specifications was: [4] [3]

Dimensions100 × 100 × 113 mm CubeSat standard
Mass800 grams
Expected lifetimeMinimum 1 month
Attitude determination system Sun sensors, gyro sensors, magnetometers
Attitude control systemMagnetic coils
PowerSolar-cell panels located in satellite surface
Batteries Li-ion 8.2V 2200 mAh
Power bus3.3 and 5V regulated
Antenna COM - UHF tx/rxdipole (Be-Cu)
Antenna AIS (VHF)dipole (Be-Cu)

See also

Related Research Articles

CubeSat 10×10×10 cm nanosatellites

A CubeSat is a type of miniaturized satellite for space research that is made up of multiple cubic modules of 10 cm × 10 cm × 10 cm size. CubeSats have a mass of no more than 1.33 kilograms (2.9 lb) per unit, and often use commercial off-the-shelf (COTS) components for their electronics and structure. CubeSats are put into orbit by deployers on the International Space Station, or launched as secondary payloads on a launch vehicle. As of August 2021, more than 1600 CubeSats have been launched and more than 90 have been destroyed in launch failures.

HAMSAT also known as HAMSAT INDIA, VU2SAT and VO-52 is a microsatellite weighing 42.5 kilograms (93.7 lb), providing amateur radio satellite communications services for Indian and international amateur radio operators. This satellite carries the in-orbit designation of VO-52, and is an OSCAR series satellite.

AAU CubeSat

AAU CubeSat was a CubeSat built and operated by students from Aalborg University in Denmark. AAU CubeSat was launched on 30 June 2003 from the Plesetsk Cosmodrome on a Russian "Rockot" rocket.

The Canadian Advanced Nanospace eXperiment (CanX) program is a Canadian CubeSat nanosatellite program operated by the University of Toronto Institute for Aerospace Studies, Space Flight Laboratory (UTIAS/SFL). The program's objectives are to involve graduate students in the process of spaceflight development, and to provide low-cost access to space for scientific research and the testing of nanoscale devices. The CanX projects include CanX-1, CanX-2, the BRIght Target Explorer (BRITE), and CanX-4&5.

AAUSat-2

AAUSat-2, also spelled as AAUSAT-II, is the second student-built CubeSat built and operated by students from Aalborg University in Denmark. It was launched 28 April 2008 05:53:51 UTC from Satish Dhawan Space Centre in India on a Polar Satellite Launch Vehicle (PSLV) launch vehicle. AAUSat-2 carries a gamma radiation sensor.

Compass-1

Compass-1 is a German amateur CubeSat picosatellite, built and operated in the late 2000s by Aachen University of Applied Science. It was launched by the Indian Space Research Organisation, aboard a PSLV rocket as a secondary payload to the CartoSat-2A primary spacecraft on 28 April 2008. It was launched into a Geocentric orbit with an altitude of 597 km. Its primary mission is remote sensing; however, it also contains some technology demonstration experiments regarding the use of small satellites and GPS tracking.

Resourcesat-2 Indian Earth observation satellite

Resourcesat-2 is a follow on mission to Resourcesat-1 and the eighteenth Indian remote sensing satellite built by Indian Space Research Organisation (ISRO). The new satellite provides the same services as the original Resourcesat-1, but was also designed to "provide data with enhanced multispectral and spatial coverage". Compared to Resourcesat-1, LISS-4 multispectral swath has been enhanced from 23 km to 70 km based on user needs. Suitable changes including miniaturization in payload electronics have been incorporated in Resourcesat-2.

ITUpSAT1, short for Istanbul Technical University picoSatellite-1) is a single CubeSat built by the Faculty of Aeronautics and Astronautics at the Istanbul Technical University. It was launched on 23 September 2009 atop a PSLV-C14 satellite launch vehicle from Satish Dhawan Space Centre, Sriharikota, Andhra Pradesh in India, and became the first Turkish university satellite to orbit the Earth. It was expected to have a minimum of six-month life term, but it is still functioning for over two years. It is a picosatellite with side lengths of 10 centimetres (3.9 in) and a mass of 0.990 kilograms (2.18 lb).

SSETI Express was the first spacecraft to be designed and built by European students and was launched by the European Space Agency. SSETI Express is a small spacecraft, similar in size and shape to a washing machine. On board the student-built spacecraft were three CubeSat picosatellites, extremely small satellites weighing around one kg each. These were deployed one hour and forty minutes after launch. Twenty-one university groups, working from locations spread across Europe and with very different cultural backgrounds, worked together via the internet to jointly create the satellite. The expected lifetime of the mission was planned to be 2 months. SSETI Express encountered an unusually fast mission development: less than 18 months from kick-off in January 2004 to flight-readiness.

Jugnu, is an Indian technology demonstration and remote sensing CubeSat satellite which was operated by the Indian Institute of Technology Kanpur. Built under the guidance of Dr. N. S. Vyas, it is a nanosatellite which will be used to provide data for agriculture and disaster monitoring. It is a 3-kilogram (6.6 lb) spacecraft, which measures 34 centimetres (13 in) in length by 10 centimetres (3.9 in) in height and width. Its development programme cost around 25 million rupee. It has a design life of one year.

SARAL Indian Earth observation satellite

SARAL is a cooperative altimetry technology mission of Indian Space Research Organisation (ISRO) and Centre National d'Études Spatiales (CNES). SARAL performs altimetric measurements designed to study ocean circulation and sea surface elevation.

CubeSat Space Protocol (CSP) is a small network-layer delivery protocol designed for CubeSats. The idea was developed by a group of students from Aalborg University in 2008, and further developed for the AAUSAT3 CubeSat mission that was launched in 2013. The protocol is based on a 32-bit header containing both network and transport layer information. Its implementation is designed for embedded systems such as the 8-bit AVR microprocessor and the 32-bit ARM and AVR from Atmel. The implementation is written in C and is ported to run on FreeRTOS and POSIX and pthreads-based operating systems such as Linux. Support for Mac OS X and Microsoft Windows will be available in version 1.1. The three-letter acronym CSP was adopted as an abbreviation for CAN Space Protocol because the first MAC-layer driver was written for CAN-bus. The physical layer has since been extended to include several other technologies, and the name was therefore extended to the more general CubeSat Space Protocol without changing the abbreviation.

SwissCube-1

SwissCube-1 is a Swiss satellite operated by École Polytechnique Fédérale de Lausanne (EPFL). The spacecraft is a single unit CubeSat, which was designed to conduct research into nightglow within the Earth's atmosphere, and to develop technology for future spacecraft. It has also been used for amateur radio. It was the first Swiss satellite to be launched.

RAX-2

RAX-2 is a CubeSat satellite built as a collaboration between SRI International and students at the University of Michigan College of Engineering. It is the second spacecraft in the RAX mission. The RAX-1 mission ended after approximately two months of operation due to a gradual degradation of the solar panels that ultimately resulted in a loss of power. RAX team members applied the lessons learned from RAX-1 to the design of a second flight unit, RAX-2, which performs the same mission concept of RAX-1 with improved bus performance and additional operational modes. Science measurements are enhanced through interactive experiments with high power ionospheric heaters where FAI will be generated on demand.

VesselSat-1 was a miniaturized satellite built and owned by LuxSpace, which was operated by Orbcomm under lease. VesselSat-1 and its sister satellite, VesselSat-2 were used by Orbcomm to compensate the functionality of the malfunctioning Orbcomm-QL satellites.

CUTE-1.7 + APD II, or CUTE-1.7 + APD 2, is a Japanese nanosatellite which was launched in 2008 as a follow-up to the CUTE-1.7 + APD satellite. It was built and is operated by the Tokyo Institute of Technology.

EQUiSat

EQUiSat was a 1U CubeSat designed and built by Brown Space Engineering, an undergraduate student group at Brown University's School of Engineering. EQUiSat's mission was to test a battery technology that had never flown in space which powered an beacon that was designed to be visible from Earth.

Nanoracks CubeSat Deployer Device to deploy CubeSats into orbit from the International Space Station

The Nanoracks CubeSat Deployer (NRCSD) is a device to deploy CubeSats into orbit from the International Space Station (ISS).

Swayam

Swayam is a 1-U picosatellite (CubeSat) developed by the undergraduate students of College of Engineering, Pune. They have successfully completed assembly of the flight model having a size of 1-U and weight of 990 grams under the guidance of Indian Space Research Organisation (ISRO) in January 2015. The structural design of the satellite, design of its electronic and control systems as well as the manufacturing of the satellite was carried out by the students. The project was completed over a span of 8 years and more than 200 students worked on it. The Satellite was launched by ISRO on June 22, 2016 along with Cartosat-2C by Polar Satellite Launch Vehicle C-34 from the second launch pad at Satish Dhawan Space Center, Sriharikota, India. The satellite is to be placed in low earth orbit (LEO) around the Earth at a height of 515 km.

References

  1. ↑ McDowell, Jonathan (21 July 2021). "Launch Log". Jonathan's Space Report. Retrieved 26 October 2021.
  2. ↑ "AAUSAT-3". Heavens Above. Retrieved 21 November 2013.
  3. 1 2 3 4 5 6 7 8 9 "AAUSat-3 (Aalborg University CubeSat-3)". ESA eoPortal Directory. Retrieved 26 October 2021.
  4. 1 2 "AAUSAT 3". NASA. 21 October 2021. Retrieved 26 October 2021.PD-icon.svgThis article incorporates text from this source, which is in the public domain .
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.