A gas check is a gasket type component of firearms ammunition. Gas checks are used when non-jacketed bullets are used in high pressure cartridges. The use of a gas check inhibits the buildup of lead in the barrel and improves accuracy. [1]
Contents
A gas check is a gasket type component of firearms ammunition. Gas checks are used when non-jacketed bullets are used in high pressure cartridges. The use of a gas check inhibits the buildup of lead in the barrel and improves accuracy. [1]
Gas checks are most commonly found in the form of a thin cup or disc made of a ductile metal. Copper, zinc, aluminum, and alloys such as brass have been used. A bullet designed to accept a gas check has a rebated base shank which permits attachment of the check without altering the maximum diameter of the bullet. The shallow cup-shaped check is mechanically attached to the reduced shank of the bullet by swaging.
High pressures, such as those commonly encountered in maximum loadings of magnum revolver cartridges or rifle cartridges, often result in significant problems when coupled with cast or swaged lead bullets. It was long thought that the high temperatures melted the base of the bullet, but this is no longer thought to be the case. Instead, the high pressures allow propellant gas to escape past the bullet, causing gas cutting, which increases lead deposits in the barrel and unbalances the bullet. A gas check provides a thin layer of harder but still malleable metal on the base of the bullet that obturates to provide a seal and prevents the propellant gas leakage that causes gas cutting, and helps the bullet grip the rifling. [1] [2] [3] [4] [5]
While most commercial cartridges operating at high pressure use jacketed bullets, gas checked bullets are popular with "handloaders" who can recycle lead to make cast bullets, and then must only pay for the gas check. Custom lead bullets, such as those for obsolete calibers, wildcat cartridges, or for special purposes, are easily made with inexpensive casting or swaging equipment. In contrast, manufacturing jacketed bullets requires far more expensive equipment to draw the jackets and swage in the core, so is generally limited to commercial projectile producers. As a result, although it is possible for hobbyists to manufacture jacketed bullets, many of them take the easier option and use gas checked bullets instead.
The most common use of gas checks are found in .44 Magnum, .357 Magnum, and 10mm Auto which were developed from non-magnum cartridges by firearm enthusiasts such as Elmer Keith. By loading the large capacity cases designed for black powder with large charges of smokeless powder, velocities well in excess of 1000 ft/s (300 m/s) were produced from handguns for the first time. At these velocities and pressures traditional soft lead bullets would quickly foul the barrel with lead deposits, so gas checked bullets were used in these experimental cartridges. [3]
The other common use of gas checked bullets is in obsolete military rifles. Many of these rifles used calibers that were unique to the rifle; low levels of commercial production and dwindling supplies of surplus ammunition quickly result in high ammunition prices. Many of these rifles use unusual bore diameters; for example, both the British 7.7×56mmR and Soviet 7.62×54mmR rifle cartridges use bore diameters larger than US .30 caliber (7.62 mm) standard bullets, resulting in a much smaller supply of suitable bullets—often just a single full metal jacket bullet design in the weight used by the military loading. Custom made bullets also allow the bullet to be carefully sized to match the bore, which can vary considerably in surplus rifles, and provide both more accuracy and more flexibility. Gas checks allow these bullets to be pushed to higher velocities without undue fouling of the barrel and attendant problems. [2]
Handloading, or reloading, is the practice of making firearm cartridges by assembling the individual components, rather than purchasing mass-assembled, factory-loaded ammunition.
A bullet is a kinetic projectile, a component of firearm ammunition that is shot from a gun barrel. Bullets are made of a variety of materials, such as copper, lead, steel, polymer, rubber and even wax. Bullets are made in various shapes and constructions, including specialized functions such as hunting, target shooting, training and combat. Bullets are often tapered, making them more aerodynamic. Bullet sizes are expressed by their weights and diameters in both imperial and metric measurement systems. For example: 55 grain .223 caliber bullets are of the same weight and caliber as 3.56 gram 5.56mm caliber bullets. Bullets do not normally contain explosives but strike or damage the intended target by transferring kinetic energy upon impact and penetration. Bullets shot by firearms can be used for target practice or to injure or kill animals or people.
A cartridge or a round is a type of pre-assembled firearm ammunition packaging a projectile, a propellant substance and an ignition device (primer) within a metallic, paper, or plastic case that is precisely made to fit within the barrel chamber of a breechloading gun, for the practical purpose of convenient transportation and handling during shooting. Although in popular usage the term "bullet" is often informally used to refer to a complete cartridge, it is correctly used only to refer to the projectile.
The .38 Special, also commonly known as .38 S&W Special, .38 Smith & Wesson Special, .38 Spl, .38 Spc,, or 9x29mmR is a rimmed, centerfire cartridge designed by Smith & Wesson.
A centerfire cartridge is a firearm metallic cartridge whose primer is located at the center of the base of its casing. Unlike rimfire cartridges, the centerfire primer is typically a separate component seated into a recessed cavity in the case head and is replaceable by reloading.
A sabot is a supportive device used in firearm/artillery ammunitions to fit/patch around a projectile, such as a bullet/slug or a flechette-like projectile, and keep it aligned in the center of the barrel when fired. It allows a narrower projectile with high sectional density to be fired through a barrel of much larger bore diameter with maximal accelerative transfer of kinetic energy. After leaving the muzzle, the sabot typically separates from the projectile in flight, diverting only a very small portion of the overall kinetic energy.
The .22 Long Rifle or simply .22 LR is a long-established variety of .22 caliber rimfire ammunition originating from the United States. It is used in a wide range of rifles, pistols, revolvers, smoothbore shotguns, and submachine guns.
Internal ballistics, a subfield of ballistics, is the study of the propulsion of a projectile.
In the field of firearms and airguns, obturation denotes necessary barrel blockage or fit by a deformed soft projectile. A bullet or pellet, made of soft material and often with a concave base, will flare under the heat and pressure of firing, filling the bore and engaging the barrel's rifling. The mechanism by which an undersized soft-metal projectile enlarges to fill the barrel is, for hollow-base bullets, expansion from gas pressure within the base cavity and, for solid-base bullets, "upsetting"—the combined shortening and thickening that occurs when a malleable metal object is struck forcibly at one end.
The .458 Winchester Magnum is a belted, straight-taper cased, big five game rifle cartridge. It was introduced commercially in 1956 by Winchester and first chambered in the Winchester Model 70 African rifle. It was designed to compete against the .450 Nitro Express and the .470 Nitro Express cartridges used in big bore British double rifles. The .458 Winchester Magnum remains one of the most popular large game cartridges, and most major ammunition manufacturers offer a selection of .458 ammunition.
The .416 Rigby is a rifle cartridge designed in 1911 by London based gunmaker John Rigby & Company, for hunting dangerous game. It is the first cartridge to use a bullet of .416 inch diameter. The rifles, as built by John Rigby & Co., were initially made up on the Magnum Mauser 98 action, although in later years, some were made on standard length actions, a perfect example being the rifle used by legendary professional hunter Harry Selby. Other famous users of the cartridge were Commander David Enderby Blunt, John Taylor, and Jack O'Connor.
The .444 Marlin (10.9×57mmR) is a rifle cartridge designed in 1964 by Marlin Firearms and Remington Arms. It was designed to fill in a gap left by the older .45-70 when that cartridge was not available in any new lever action rifles; at the time it was the largest lever-action cartridge available. The .444 resembles a lengthened .44 Magnum and provides a significant increase in velocity. It is usually used in the Marlin 444 lever-action rifle.
The .30-378 Weatherby Magnum is a .30 caliber, belted, bottle-necked rifle cartridge. The cartridge was developed in response to a US Army military contract in 1959. While still unreleased to the public, the cartridge went on to set world records for accuracy including the first ten 10X in 1,000 yards (910 m) benchrest shooting. It is currently the highest velocity .30 caliber factory ammunition available.
Overpressure ammunition, commonly designated as +P or +P+, is small arms ammunition that has been loaded to produce a higher internal pressure when fired than is standard for ammunition of its caliber, but less than the pressures generated by a proof round. This is done typically to produce rounds with a higher muzzle velocity and stopping power, such as ammunition used for defensive or hunting purposes. Because of this, +P ammunition is typically found in handgun calibers which might be used for defensive purposes.
The 8×68mm S rebated rim bottlenecked centerfire rifle cartridge was developed in the 1930s by August Schüler of the August Schüler Waffenfabrik, Suhl, Germany as a magnum hunting cartridge that would just fit and function in standard-sized Mauser 98 bolt-action rifles. The bore has the same lands and grooves diameters as the German 7.92×57mm Mauser service cartridge. This is one of the early examples where a completely new rifle cartridge was developed by a gunsmith to fit a specific popular and widespread type of rifle.
The .351 Winchester Self-Loading is an American rifle cartridge designed in 1906.
The following are terms related to firearms and ammunition topics.
The .325 Winchester Short Magnum, commonly known as the 325 WSM is an 8mm caliber rebated rim bottlenecked centerfire short magnum medium bore cartridge. The cartridge was introduced by Winchester Ammunition in 2005.
A cast bullet is made by allowing molten metal to solidify in a mold. Most cast bullets are made of lead alloyed with tin and antimony; but zinc alloys have been used when lead is scarce, and may be used again in response to concerns about lead toxicity. Most commercial bullet manufacturers use swaging in preference to casting, but bullet casting remains popular with handloaders.
The .276 Enfield (7×60mm) was an experimental rebated rim bottlenecked centerfire military rifle cartridge developed in conjunction with the Pattern 1913 Enfield (P'13) rifle. Development was discontinued by the onset of World War I.