This article needs additional citations for verification .(September 2015) |
Pump action is a type of manual firearm action that is operated by moving a sliding handguard on the gun's forestock. When shooting, the sliding forend is pulled rearward to eject any expended cartridge and typically to cock the hammer or striker, and then pushed forward to load a new cartridge into the chamber. Most pump-action firearms use an integral tubular magazine, although some do use detachable box magazines. Pump-action firearms are typically associated with shotguns, although it has also been used in rifles, grenade launchers, and other types of firearms. A firearm using this operating mechanism is colloquially referred to as a pumpgun.
Because the forend is manipulated usually with the support hand, a pump-action firearm is much faster than a bolt-action and somewhat faster than a lever-action, as it does not require the trigger hand to be removed from the trigger while reloading. Also because the action is cycled in a linear fashion, it creates less torque that can tilt and throw the gun off aim when repeat-firing rapidly.
The first slide action patent was issued to Alexander Bain of Britain in 1854. [1] [2] The first pump action firearm with a magazine was technically the gun patented in America on the 22nd of May in 1866 by Josiah V. Meigs although the pump action was actuated via the trigger guard rather than a sliding handguard underneath the barrel. [3] The first magazine-using pump-action firearm to operate using a sliding handguard underneath the barrel was the firearm patented by William Krutzsch of Britain on the 27th of August in 1866, a few months after Meigs. [4] The first pump-action shotgun to be sold commercially and in substantial quantities was the Spencer 1882. [5] [6]
Many older pump-action shotguns can be fired faster than modern ones, as they often did not have a trigger disconnector, and were capable of firing a new round as fast as the pump action was cycled, with the trigger held down continuously. This technique is called a slamfire, and was often used in conjunction with the M1897 and M1912 shotguns in World War I trench warfare. [7]
Modern pump-action designs are a little slower than a semi-automatic shotgun, but the pump-action offers greater flexibility in selection of shotshells, allowing the shooter to mix different types of loads and for using low-power or specialty loads. Semi-automatic shotguns must use some of the energy of each round fired to cycle their actions, meaning that they must be loaded with shells powerful enough to reliably cycle. The pump-action avoids this limitation. In addition, like all manual action guns, pump-action guns are inherently more reliable than semi-automatic guns under adverse conditions, such as exposure to dirt, sand, or climatic extremes. Thus, until recently, military combat shotguns were almost exclusively pump-action designs. [8]
Like most lever-action rifles and shotguns, the majority of pump-action shotguns and rifles use a fixed tubular magazine. This makes for slow reloading, as the cartridges have to be inserted individually into the magazine of the firearm. However, some pump-action shotguns and rifles, including the Russian Zlatoust RB-12, Italian Valtro PM5, American Remington 7600 series, and the Mossberg 590M, use detachable box magazines.
A pump-action firearm is typically fed from a tubular magazine underneath the barrel, which also serves as a guide to the movable forend. The rounds are fed in one by one through a port in the receiver, where they are pushed forward. A latch at the rear of the magazine holds the rounds in place in the magazine until they are needed. If it is desired to load the gun fully, a round may be loaded through the ejection port directly into the chamber, or cycled from the magazine, which is then topped off with another round. Pump shotguns with detachable box magazines or even drums exist, and may or may not allow the magazine to be inserted without stripping the top round.
Nearly all pump-actions use a back-and-forward motion of the forend to cycle the action. Only a few pump-actions use the "reverse" or forward-and-back motion of the forend to cycle the action, a few examples are the Russian RMB-93 and South African NeoStead 2000. The forend is connected to the bolt by one or two bars; two bars are considered more reliable because it provides symmetric forces on the bolt and pump and reduces the chances of binding. The motion of the bolt back and forth in a tubular magazine model will also operate the elevator, which lifts the shells from the level of the magazine to the level of the barrel.
After firing a round, the bolt is unlocked and the forend is free to move. The shooter pulls back on the forend to begin the operating cycle. The bolt unlocks and begins to move to the rear, which extracts and ejects the empty shell from the chamber, cocks the hammer, and begins to load the new shell. In a tubular magazine design, as the bolt moves rearwards, a single shell is released from the magazine, and is pushed backwards to come to rest on the elevator.
As the forend reaches the rear and begins to move forward, the elevator lifts up the shell, lining it up with the barrel. As the bolt moves forward, the round slides into the chamber, and the final portion of the forend's travel locks the bolt into position. A pull of the trigger will fire the next round, where the cycle begins again.
Most pump-action firearms do not have any positive indication that they are out of ammunition, so it is possible to complete a cycle and have an empty chamber. The risk of running out of ammunition unexpectedly can be minimized in a tubular magazine firearm by topping off the magazine by loading new rounds to replace the rounds that have just been fired. This is especially important when hunting, as many locations have legal limits on the magazine capacity: for example, three rounds for shotguns and five rounds for rifles.
The BSA Machine Carbine used a unique pump-action that also required twisting the handguard.
Another variant was the Burgess Folding Shotgun from the late 19th century where instead of manipulating the forend to cycle the action, it had a sleeve around the grip area of the stock which the shooter would slide back and forward to cycle the gun. This was done because the forend based pump action was under patent at the time. [9]
Pump-action shotguns, also called pump shotguns, slide-action repeating shotguns or slide-action shotguns are the most commonly seen pump-action firearms. These shotguns typically use a tubular magazine underneath the gun barrel to hold the shells, though there are some variants that use a box magazine like most rifles. It's not uncommon to see extra ammunition stored in externally mounted "shell holder" racks (usually as "sidesaddle" on one side of the receiver, or on the buttstock) for quick on-field reloading. The shells are chambered and extracted by pulling/pushing the sliding fore-end enveloping the tubular magazine toward the user.
In modern shotguns, the fore-end can be replaceable and often include picatinny rails or M-LOK for mounting accessories such as a tactical light, and the traditional straight grip might be replaced with a pistol grip for a more stable control.
Modern pump shotgun designs, such as the Remington 870 and Mossberg 500, have a safety feature called a trigger disconnector, which disconnects the trigger from the sear as the bolt moves back, so that the trigger must be released and pulled again to fire the shotgun after it closes. Many early pump shotguns, such as the Winchester 1897, did not have trigger disconnectors, and would, if the trigger were held back, fire immediately upon closing. [7] Due to the higher rate of fire that this allows, some shooters prefer models without this feature, such as the Ithaca 37, [10] Stevens Model 520/620, [11] and Winchester Model 12. [7]
When used in rifles, this action is also commonly called a slide action. In the late 19th and early 20th century it was referred to as a trombone action, because it functioned similarly to the musical instrument of the same name. [12] Colt manufactured the Colt Lightning Carbine from 1884 to 1904 chambered in .44-40 caliber. [13] [14] The slide action Winchester Model 1890 chambered in .22 caliber was one of the most successful repeating rimfire rifle made by Winchester. Approximately 849,000 Model 1890 rifles were produced between 1890 and 1932. Later pump-action rifles were also manufactured by Winchester, Marlin, Browning and Remington. [15]
A "reverse pump-action" design can sometimes be found, where the extraction is done by pushing the fore-end forwards, and re-chambered by pulling backwards. One such 21st-century variant is the Krieghoff Semprio "in-line repeating rifle". [16] [17] The Semprio is a reverse pump-action system that ejects cartridges when the fore-end is pushed forward and loads the chamber when pulled backward. The Semprio's 7-lug bolt head design displays a locking surface of 65 mm2 (0.101 in2) compared to the 56 mm2 (0.087 in2) of the Mauser M98 bolt-action rifle. [18]
The term pump-action can also be applied to various airsoft guns and air guns, which use a similar mechanism to both load a pellet and compress a spring piston for power, or pneumatic guns where a pump is used to compress the air used for power. See the airgun article for information on how spring piston and pneumatic airguns work.
The 43mm GM-94 is a pump-action grenade launcher developed by the KBP design bureau for use by Russian special forces. It carries three rounds in an above-the-barrel tubular magazine.
Another pump-action grenade launcher is the China Lake grenade launcher, which saw usage by the U.S. Navy SEALS in the Vietnam War in limited numbers.
A shotgun is a long-barreled firearm designed to shoot a straight-walled cartridge known as a shotshell, which discharges numerous small spherical projectiles called shot, or a single solid projectile called a slug. Shotguns are most commonly used as smoothbore firearms, meaning that their gun barrels have no rifling on the inner wall, but rifled barrels for shooting sabot slugs are also available.
In firearm designs, the term single-shot refers to guns that can hold only a single round of ammunition inside and thus must be reloaded manually after every shot. Compared to multi-shot repeating firearms ("repeaters"), single-shot designs have no moving parts other than the trigger, hammer/firing pin or frizzen, and therefore do not need a sizable receiver behind the barrel to accommodate a moving action, making them far less complex and more robust than revolvers or magazine/belt-fed firearms, but also with much slower rates of fire.
In firearms terminology, an action is the functional mechanism of a breech-loading firearm that handles the ammunition cartridges, or the method by which that mechanism works. Actions are technically not present on muzzleloaders, as all those are single-shot firearms with a closed off breech with the powder and projectile manually loaded from the muzzle. Instead, the muzzleloader ignition mechanism is referred to as the lock.
Winchester rifle is a comprehensive term describing a series of lever action repeating rifles manufactured by the Winchester Repeating Arms Company. Developed from the 1860 Henry rifle, Winchester rifles were among the earliest repeaters. The Model 1873 was particularly successful, being marketed by the manufacturer as "The Gun That Won the West".
The Winchester Model 1897, also known as the Model 97, M97, Riot Gun, or Trench Gun, is a pump-action shotgun with an external hammer and tube magazine manufactured by the Winchester Repeating Arms Company. The Model 1897 was an evolution of the Winchester Model 1893 designed by John Browning. From 1897 until 1957, over one million of these shotguns were produced. The Model 1897 was offered in numerous barrel lengths and grades, chambered in 12 and 16 gauge, and as a solid frame or takedown. The 16-gauge guns had a standard barrel length of 28 in (71 cm), while 12-gauge guns were furnished with 30 in (76 cm) barrels. Special length barrels could be ordered in lengths as short as 20 in (51 cm) or as long as 36 in (91 cm). Since the time the Model 1897 was first manufactured, it has been used to great effect by American military personnel, law enforcement officers, and hunters.
A repeating rifle is a single-barreled rifle capable of repeated discharges between each ammunition reload. This is typically achieved by having multiple cartridges stored in a magazine and then fed individually into the chamber by a reciprocating bolt, via either a manual or automatic action mechanism, while the act of chambering the round typically also recocks the hammer/striker for the following shot. In common usage, the term "repeating rifle" most often refers specifically to manual repeating rifles, as opposed to self-loading rifles, which use the recoil, gas, or blowback of the previous shot to cycle the action and load the next round, even though all self-loading firearms are technically a subcategory of repeating firearms.
A lever action is a type of action for repeating firearms that uses a manually operated cocking handle located around the trigger guard area that pivots forward to move the bolt via internal linkages, which will feed and extract cartridges into and out of the chamber, and cock the firing pin mechanism. This contrasts to other type of repeating actions such as the bolt-action, pump-action, semi-automatic, fully automatic, and/or burst mode actions. A firearm using this operating mechanism is colloquially referred to as a levergun.
A magazine, often simply called a mag, is an ammunition storage and feeding device for a repeating firearm, either integral within the gun or externally attached. The magazine functions by holding several cartridges within itself and sequentially pushing each one into a position where it may be readily loaded into the barrel chamber by the firearm's moving action. The detachable magazine is sometimes colloquially referred to as a "clip", although this is technically inaccurate since a clip is actually an accessory device used to help load ammunition into a magazine or cylinder.
A breechblock is the part of the firearm action that closes the breech of a breech loading weapon before or at the moment of firing. It seals the breech and contains the pressure generated by the ignited propellant. Retracting the breechblock allows the chamber to be loaded with a cartridge.
The Ithaca 37, also known as the Ithaca Model 37, is a pump-action shotgun made in large numbers for the civilian, law enforcement and military markets. Based on a 1915 patent by firearms designer John Browning for a shotgun initially marketed as the Remington Model 17, it utilizes a novel combination ejection/loading port on the bottom of the gun which leaves the sides closed to the elements.
The Winchester Model 1912, also commonly known as the Winchester 1912, Model 12, or M12, is an internal-hammer pump-action shotgun with an external tube magazine. Popularly named the Perfect Repeater at its introduction, it largely set the standard for pump-action shotguns over its 51-year high-rate production life. From August 1912 until first discontinued by Winchester in May 1964, nearly two million Model 12 shotguns were produced in various grades and barrel lengths. Initially chambered for 20 gauge only, the 12 and 16 gauge versions came out in 1913, and the 28 gauge version came out in 1934. A .410 version was never produced; instead, a scaled-down version of the Model 12 known as the Model 42, directly derived from scaled drawings of the Model 12, was produced in .410.
Break action is a type of firearm action in which the barrel(s) are hinged much like a door and rotate perpendicularly to the bore axis to expose the breech and allow loading and unloading of cartridges. A separate operation may be required for the cocking of a hammer to fire the new round. There are many types of break-action firearms; break actions are universal in double-barreled shotguns, double-barreled rifles, combination guns, and are commonly found in single shot pistols, rifles, shotguns, including flare guns, grenade launchers, air guns, and some older revolver designs. They are also known as hinge-action, break-open, break-barrel, break-top, or, on old revolvers, top-break actions.
The Model 1200 is a pump-action shotgun that was manufactured by the Winchester-Western Division of Olin Corporation, starting 1964. It was redesignated the Model 1300 in 1978 with minimal changes. Production ceased in 2006 when the U.S. Repeating Arms Company, the subsequent manufacturer, went bankrupt. A militarized version of the Model 1200 was acquired by the U.S. Army for use during the Vietnam War. It is still in active service within various conflicts throughout the 21st century.
The following are terms related to firearms and ammunition topics.
The Fabarm FP6 is a pump-action combat shotgun that was manufactured by the Italian firearms company Fabbrica Bresciana Armi S.p.A. (FABARM) and sold by Heckler & Koch. It was intended for civilian and law enforcement use.
The Kel-Tec KSG is a bullpup 12-gauge pump-action shotgun designed by Kel-Tec. It has two tube magazines which the user of the gun can switch between manually. Each tube holds up to seven 2.75-inch (70 mm) 12-gauge shotshells or six 3-inch (76 mm) shotshells. The Kel-Tec KSG has an overall length of 633mm. Kel-Tec has also introduced a larger variant, called the KSG25, which holds 24+1 rounds to the originals 14+1 rounds.
The DP-12 is a bullpup 12-gauge pump action double-barreled shotgun designed by Standard Manufacturing. It has two tube magazines, each of which feeds its own barrel. Each magazine tube can hold up to seven 2.75-inch (70 mm) 12-gauge shotshells or six 3-inch (76 mm) shotgun shells; 16 or 14 (3") in total with indicator windows.
A repeating firearm or repeater is any firearm that is capable of being fired repeatedly before having to be manually reloaded with new ammunition from the magazine.
Spencer 1882 is a pump-action shotgun designed by Christopher Miner Spencer and Sylvester Howard Roper, which was produced by the former's Spencer Arms Company from 1882 to 1889 or 1892, and subsequently by Francis Bannerman & Sons from 1890 to 1907. The design is credited as the first commercially successful pump-action shotgun to be the released to the markets, preceding John Browning's Winchester Model 1893 and Model 1897.