Kerosene lamp

Last updated

A kerosene lamp produced by the factory of Karlskrona Lampfabrik in Sweden c. 1890s A kerosene lamp produced by the factory of Karlskrona Lampfabrik in Sweden c. 1890s.jpg
A kerosene lamp produced by the factory of Karlskrona Lampfabrik in Sweden c. 1890s
Swiss flat-wick kerosene lamp. The knob protruding to the right adjusts the wick, and hence the flame size. SwissKeroseneLamp.jpg
Swiss flat-wick kerosene lamp. The knob protruding to the right adjusts the wick, and hence the flame size.

A kerosene lamp (also known as a paraffin lamp in some countries) is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may be used for portable lighting. Like oil lamps, they are useful for lighting without electricity, such as in regions without rural electrification, in electrified areas during power outages, at campsites, and on boats. There are three types of kerosene lamp: flat-wick, central-draft (tubular round wick), and mantle lamp. Kerosene lanterns meant for portable use have a flat wick and are made in dead-flame, hot-blast, and cold-blast variants.

Contents

Pressurized kerosene lamps use a gas mantle; these are known as Petromax, Tilley lamps, or Coleman lamps, among other manufacturers. They produce more light per unit of fuel than wick-type lamps, but are more complex and expensive in construction and more complex to operate. A hand-pump pressurizes air, which forces liquid fuel from a reservoir into a gas chamber. Vapor from the chamber burns, heating a mantle to incandescence and providing heat.

Kerosene lamps are widely used for lighting in rural areas of Africa and Asia, where electricity is not distributed or is too costly. As of 2005, kerosene and other fuel-based illumination methods consume an estimated 77 billion litres (20 billion US gallons) of fuel per year, equivalent to 8.0 million gigajoules (1.3 million barrels of oil equivalent) per day. [1] [2] This is comparable to annual U.S. jet-fuel consumption of 76 billion litres (20 billion US gallons) per year. [3] [ improper synthesis? ]

History

In 1813, John Tilley invented the hydro-pneumatic blowpipe. [4] In 1818, William Henry Tilley, gas fitters, was manufacturing gas lamps in Stoke Newington. [5]

In 1846, Abraham Pineo Gesner invented a substitute for whale oil for lighting, distilled from coal. Later made from petroleum, kerosene became a popular lighting fuel. Modern and most popular versions of the paraffin lamp were later constructed by Polish inventor and pharmacist Ignacy Łukasiewicz, in Lviv in 1853. [6] [7] [8] [9] It was a significant improvement over lamps designed to burn vegetable or sperm oil.

In 1914, the Coleman Lantern pressure lamp was introduced by the Coleman Company. [10] [11] [12]

In 1919, Tilley High-Pressure Gas Company started using kerosene as a fuel for lamps. [13]

Types

Flat-wick lamp

New Zealand Railways lamp on the Weka Pass Railway Railway Lamp.jpg
New Zealand Railways lamp on the Weka Pass Railway

A flat-wick lamp is a simple type of kerosene lamp, which burns kerosene drawn up through a wick by capillary action. If this type of lamp is broken, it can easily start a fire. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce.

The chimney is used for a more important duty. The mantle/wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the mantle, just as a chimney in a house. This has a cooling effect and keeps the mantle from overheating. Without a properly installed chimney, a definite safety condition exists. This is even more important if using Aladdin lamps. They also have a thinner chimney to induce a faster airflow. This information should be adhered to regardless of the type of lantern in use.

The lamp burner has a flat wick, usually made of cotton. The lower part of the wick dips into the fount and absorbs the kerosene; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the kerosene that the wick has absorbed burns and produces a clear, bright, yellow flame. As the kerosene burns, capillary action in the wick draws more kerosene up from the fuel tank. All kerosene flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above.

This type of lamp was very widely used by railways, both on the front and rear of trains and for hand signals, due to its reliability. At a time when there were few competing light sources at night outside major towns, the limited brightness of these lamps was adequate and could be seen at sufficient distance to serve as a warning or signal.

Central-draft (tubular round wick) lamp

A central-draft lamp is a continuation of the principles used in the Argand lamp from 1780. It also uses a tubular round wick and it also has air intake under the flame into the glass chimney. Since whale oil used in the Argand lamp has a high viscosity it was necessary to place the oil reservoir higher than the flame of the lamp itself in order to let the oil flow by pressure caused by gravity. Kerosene has a much lower viscosity and can be transported through the wick by capillary action. This made it possible to install the oil reservoir below the flame. Oil reservoirs were made with a hollow tube in the middle that transported air from below the oil reservoir into the flame. [14] The tubular woven wick (or flat wick rolled into a tube, the seam of which is then stitched together to form the complete wick) is placed around this tube. The tubular wick is then mounted into a "carrier", which is some form of a toothed rack that engages into the gears of the wick-raising mechanism of the burner and allows the wick to be raised and lowered. The wick rides in between the inner and outer wick tubes; the inner wick tube (central draft tube) provides the "central draft" or draft that supplies air to the flame spreader. When the lamp is lit, the central draft tube supplies air to the flame spreader that spreads out the flame into a ring of fire and allows the lamp to burn cleanly.

Air flow in a central draft kerosene lamp Centre draft lamp explained.jpg
Air flow in a central draft kerosene lamp

Side-draft (flat wick folded round) lamp

In 1865 the Berlin based company Wild & Wessel invented the Kosmos Brenner. [15] This lamp used a flat wick that was folded open at the bottom and gradually folded round at the top. This allowed for air flow in the centre of flame just like in centre-draft burner. Only here the air intake is done above the oil reservoir and under the burner itself. This avoids the need of a hollow tube all along the hight of the reservoir. This make it easier to use ceramic or glass oil reservoirs. While the Kosmos Brenner doesn't use a flame spreader other side draft kerosene lamps do. Examples are the Ideal Brenner and the Matador Brenner from Ehrich and Graetz

The Ideal burner. A "Side-draft" kerosene lamp with flame spreader Idealbrenner.JPG
The Ideal burner. A "Side-draft" kerosene lamp with flame spreader


Duplex lamp (2 parallel flat wicks) lamp

In 1865 the Duplex lamp also came on the market. It was a very popular type of kerosene lamp in Great Britain.

Mantle lamp

An 85 mm Chance Brothers Incandescent Petroleum Vapour Installation, which produced the light for the Sumburgh Head lighthouse until 1976. Sumburgh Lighthouse Lamp.jpg
An 85 mm Chance Brothers Incandescent Petroleum Vapour Installation, which produced the light for the Sumburgh Head lighthouse until 1976.

A variation on the "central-draft" lamp is the mantle lamp. The mantle is a roughly pear-shaped mesh made of fabric placed over the burner. The mantle typically contains thorium or other rare-earth salts; on first use the cloth burns away, and the rare-earth salts are converted to oxides, leaving a very fragile structure, which incandesces (glows brightly) upon exposure to the heat of the burner flame. Mantle lamps are considerably brighter than flat- or round-wick lamps, produce a whiter light and generate more heat. Mantle lamps typically use fuel faster than a flat-wick lamp, but slower than a center-draft round-wick, as they depend on a small flame heating a mantle, rather than having all the light coming from the flame itself.

Mantle lamps are nearly always bright enough to benefit from a lampshade, and a few mantle lamps may be enough to heat a small building in cold weather. Mantle lamps, because of the higher temperature at which they operate, do not produce much odor, except when first lit or extinguished. Like flat- and round-wick lamps, they can be adjusted for brightness; however, caution must be used, because if set too high, the lamp chimney and the mantle can become covered with black areas of soot. A lamp set too high will burn off its soot harmlessly if quickly turned down, but if not caught soon enough, the soot itself can ignite, and a "runaway lamp" condition can result.

All unpressurized mantle lamps are based on the Argand lamp that was improved by the Clamond basket mantle. These lamps were popular from 1882 until shortly after WWII, when rural electrification made them obsolete. Aladdin Lamps is the only maker of this style lamp today. [16] Even they, are now marketing electric fixtures that fit the old style lamps.

Large fixed pressurized kerosene mantle lamps were used in lighthouse beacons for navigation of ships, brighter and with lower fuel consumption than oil lamps used before. [17] An early version of the gas mantle lamp, kerosene was vaporized by a secondary burner, which pressurized the kerosene tank that supplied the central draught. Like all gas mantle lamps, the only purpose of the burner is to hold the flame that heats the mantle, which is 4-5 times as bright as the wick itself. The Coleman Lantern is the direct descendant of this type lamp.

Kerosene lantern

Dead-flame Kerosene-lamp-01.JPG
Dead-flame

A kerosene lantern, also known as a "barn lantern" or "hurricane lantern", is a flat-wick lamp made for portable and outdoor use. They are made of soldered or crimped-together sheet-metal stampings, with tin-plated sheet steel being the most common material, followed by brass and copper. There are three types: dead-flame, hot-blast, and cold-blast. Both hot-blast and cold-blast designs are called tubular lanterns and are safer than dead-flame lamps, as tipping over a tubular lantern cuts off the oxygen flow to the burner and will extinguish the flame within seconds. [18]

Hot-blast Tranby house 49 gnangarra.jpg
Hot-blast
Cold-blast Kerosine lamp.jpg
Cold-blast

The earliest portable kerosene "glass globe" lanterns, of the 1850s and 1860s, were of the dead-flame type, meaning that it had an open wick, but the airflow to the flame was strictly controlled in an upward motion by a combination of vents at the bottom of the burner and an open topped chimney. This had the effect of removing side-to-side drafts and thus significantly reducing or even eliminating the flickering that can occur with an exposed flame.

Later lanterns, such as the hot-blast and cold-blast lanterns, took this airflow control even further by partially or fully enclosing the wick in a "deflector" or "burner cone" and then channeling the air to be supplied for combustion at the wick while at the same time pre-heating the air for combustion.

The hot-blast design, also known as a "tubular lantern" due to the metal tubes used in its construction, was invented by John H. Irwin and was patented on May 4, 1869 . [19] As noted in the patent, the "novel mode of constructing a lantern whereby the wind, instead of acting upon the flame in such a manner as to extinguish it, serves to support or sustain and prevent the extinguishment thereof." This improvement essentially redirected wind which might normally tend to extinguish the flame of an unprotected dead-flame lantern, instead is redirected, slowed, pre-heated, and supplied to the burner to actually support and promote the combustion of the fuel.

Later, Irwin improved upon this design by inventing and patenting his cold-blast design on May 6, 1873 . [20] This design is similar to his earlier "hot-blast" design, except that the oxygen-depleted hot combustion byproducts are redirected and prevented from recirculating back to the burner by redesigning the intake products, so that only oxygen-rich, fresh air is drawn from the atmosphere into the lamp ("the inlets for fresh air are placed out of the ascending current of products of combustion, and said products are thereby prevented from entering [the air intake]" [20] ). The primary benefit of this design compared to the earlier "hot-blast" design was to maximize the amount of oxygen available for combustion by ensuring that only fresh air is supplied to the burner, thereby increasing the brightness and stability of the flame. [Note 1]

Safety

Combustion

Contamination of lamp fuel with even a small amount of gasoline results in a lower flash point and higher vapor pressure for the fuel, with potentially dangerous consequences. Vapors from spilled fuel may ignite; vapor trapped above liquid fuel may lead to excess pressure and fires. Kerosene lamps are still extensively used in areas without electrical lighting; the cost and dangers of combustion lighting are a continuing concern in many countries. [21]

Inhalation

The World Health Organization considers kerosene to be a polluting fuel and recommends that “governments and practitioners immediately stop promoting its household use”. [22] Kerosene smoke contains high levels of harmful particulate matter, and household use of kerosene is associated with higher risks of cancer, respiratory infections, asthma, tuberculosis, cataract, and adverse pregnancy outcomes. [23]

Performance

Flat-wick lamps have the lowest light output, center-draft round-wick lamps have 3–4 times the output of flat-wick lamps, and pressurized lamps have higher output yet; the range is from 8 to 100 lumens. A kerosene lamp producing 37 lumens for 4 hours per day for a month (120 hours) consumes about 3 litres (6.3 US pt; 5.3 imp pt) of kerosene. [24]

Oil lamp output in candlepower (CP), lumens and incandescent electric watts equivalent [ citation needed ]
Flat-wick widthCandlepowerLumensWatts [25]
3/8"4503.3
1/2"7885.9
5/8"91137.5
3/4"101258.3
7/8"–1"1215110.1
1-1/2"2025116.7
2× 1", 1-1/16", 1-1/8"3037725
2× 1-1/2"50628.542
1-1/4" round "Dressel Belgian"6784256
1-1/2" round "Rayo"80100066.6
2-1/2" round "Firelight" or "store" lamp3003771251

12.57 lumens = 1 CP

See also

Notes

  1. ↑ It is worth noting that the terms "hot-blast" and "cold-blast" do not appear directly in either of John Irwin's patents. It is likely these terms came into use later or were possibly marketing terms invented by sellers of kerosene lamps.

Related Research Articles

<span class="mw-page-title-main">Bunsen burner</span> Laboratory device used to make fire from fuel and oxidizer gases

A Bunsen burner, named after Robert Bunsen, is a kind of ambient air gas burner used as laboratory equipment; it produces a single open gas flame, and is used for heating, sterilization, and combustion.

Kerosene, or paraffin, is a combustible hydrocarbon liquid which is derived from petroleum. It is widely used as a fuel in aviation as well as households. Its name derives from κηρός (kērós) meaning "wax", and was registered as a trademark by Nova Scotia geologist and inventor Abraham Gesner in 1854 before evolving into a generic trademark. It is sometimes spelled kerosine in scientific and industrial usage.

<span class="mw-page-title-main">Candle</span> Wick embedded in solid flammable substance

A candle is an ignitable wick embedded in wax, or another flammable solid substance such as tallow, that provides light, and in some cases, a fragrance. A candle can also provide heat or a method of keeping time. Candles have been used for over two millennia around the world, and were a significant form of indoor lighting until the invention of other types of light sources. Although electric light has largely made candle use nonessential for illumination, candles are still commonly used for functional, symbolic and aesthetic purposes and in specific cultural and religious settings.

<span class="mw-page-title-main">Oil lamp</span> Lamp used for lighting by burning oil

An oil lamp is a lamp used to produce light continuously for a period of time using an oil-based fuel source. The use of oil lamps began thousands of years ago and continues to this day, although their use is less common in modern times. They work in the same way as a candle but with fuel that is liquid at room temperature, so that a container for the oil is required. A textile wick drops down into the oil, and is lit at the end, burning the oil as it is drawn up the wick.

<span class="mw-page-title-main">Lantern</span> Portable lighting device

A lantern is a source of lighting, often portable. It typically features a protective enclosure for the light source – historically usually a candle, a wick in oil, or a thermoluminescent mesh, and often a battery-powered light in modern times – to make it easier to carry and hang up, and make it more reliable outdoors or in drafty interiors. Lanterns may also be used for signaling, as torches, or as general light-sources outdoors.

<span class="mw-page-title-main">Gas mantle</span> Device for generating bright light when heated by a flame

An incandescent gas mantle, gas mantle or Welsbach mantle is a device for generating incandescent bright white light when heated by a flame. The name refers to its original heat source in gas lights which illuminated the streets of Europe and North America in the late 19th century. Mantle refers to the way it hangs like a cloak above the flame. Gas mantles were also used in portable camping lanterns, pressure lanterns and some oil lamps.

<span class="mw-page-title-main">Gas lighting</span> Type of artificial light

Gas lighting is the production of artificial light from combustion of a fuel gas such as methane, propane, butane, acetylene, ethylene, hydrogen, carbon monoxide, coal gas or natural gas. The light is produced either directly by the flame, generally by using special mixes of illuminating gas to increase brightness, or indirectly with other components such as the gas mantle or the limelight, with the gas primarily functioning to heat the mantle or the lime to incandescence.

<span class="mw-page-title-main">Ami Argand</span> Genevan physicist and chemist

François-Pierre-Amédée Argand, known as Ami Argand was a Genevan physicist and chemist. He invented the Argand lamp, a great improvement on the traditional oil lamp.

<span class="mw-page-title-main">Kerosene heater</span> Typically a portable, unvented, kerosene-fueled, space heating device

A kerosene heater, also known as a paraffin heater, is typically a portable, unvented, kerosene-fueled, space heating device. In Japan and other countries, they are a primary source of home heat. In the United States and Australia, they are a supplemental heat or a source of emergency heat during a power outage. Most kerosene heaters produce between 3.3 and 6.8 kilowatts.

<span class="mw-page-title-main">Primus stove</span> Company

The Primus stove was the first pressurized-burner kerosene (paraffin) stove, developed in 1892 by Frans Wilhelm Lindqvist, a factory mechanic in Stockholm. The stove was based on the design of the hand-held blowtorch; Lindqvist's patent covered the burner, which was turned upward on the stove instead of outward as on the blowtorch. The same year, Lindqvist partnered with Johan Viktor Svenson and established J.V. Svenson's Kerosene Stove Factory for manufacturing the new stoves which were sold under the name Primus. The first model was the No.1 stove, which was quickly followed by a number of similarly designed stoves of different models and sizes. Shortly thereafter, B.A. Hjorth & Co., a tool and engineering firm begun in Stockholm in 1889, acquired the exclusive rights to sell the Primus stove.

<span class="mw-page-title-main">Tilley lamp</span> Pressurized kerosene lamps made by the Tilley company in the UK

The Tilley lamp is a kerosene pressure lamp.

<span class="mw-page-title-main">Argand lamp</span> Type of oil lamp

The Argand lamp is a type of oil lamp invented in 1780 by Aimé Argand. Its output is 6 to 10 candelas, brighter than that of earlier lamps. Its more complete combustion of the candle wick and oil than in other lamps required much less frequent trimming of the wick.

<span class="mw-page-title-main">R. E. Dietz Company</span> Lighting products manufacturer

R. E. Dietz Co., Ltd. is a lighting products manufacturer best known for its hot blast and cold blast kerosene lanterns. The company was founded in 1840 when its founder, 22-year-old Robert Edwin Dietz, purchased a lamp and oil business in Brooklyn, New York. Though famous for well-built indoor and outdoor kerosene lanterns, it was a major player in the automotive lighting industry from the 1920s into the 1960s.

<span class="mw-page-title-main">Petromax</span> Brand of paraffin lamp

Petromax was one of the brand names from Ehrich & Graetz. The company used it for their pressurised kerosene lamp that uses a incandescent mantle. They are as synonymous with the paraffin lamp in Continental Europe as Tilley lamps are in Britain and Coleman lanterns are in the United States. Today's company Petromax GmbH sells not only pressurised paraffin lamps lamps but also other products for camping and outdoor use.

Camphine was the British trade name of a 19th-century lamp fuel made from purified spirits of turpentine. Generally prepared by distilling turpentine with quicklime, it gave off a brilliant light. It was burned in chimney lamps that produced a strong draft to prevent smoking. Invented in 1838, it was a popular domestic lamp fuel until the 1860s. Camphine was alternatively spelled camphene, especially in the United States.

<span class="mw-page-title-main">Carcel lamp</span> Oil lamp with a clockwork pump mechanism

The Carcel lamp was an efficient lighting device used in the nineteenth century for domestic purposes and in France as the standard measure for illumination.

<span class="mw-page-title-main">Blowtorch</span> Fuel-burning tool for applying flame and heat for various applications

A blowtorch, also referred to as a blowlamp, is an ambient air fuel-burning tool used for applying flame and heat to various applications, usually in metalworking.

<span class="mw-page-title-main">Luminous flame</span>

A luminous flame is a burning flame which is brightly visible. Much of its output is in the form of visible light, as well as heat or light in the non-visible wavelengths.

A Wells light was a large paraffin-fuelled (kerosene) blowlamp used for engineering work, particularly for illumination, in Victorian times. At a time before widespread electrical lighting, they were the most common form of high-powered portable illumination used for construction work, particularly railways, civil engineering, shipyards and ironworks.

References

  1. ↑ Jean-Claude Bolay, Alexandre Schmid, Gabriela Tejada Technologies and Innovations for Development: Scientific Cooperation for a Sustainable Future, Springer, 2012 ISBN   2-8178-0267-5 page 308.
  2. ↑ Mills, E. (May 27, 2005). "ENVIRONMENT: The Specter of Fuel-Based Lighting". Science. 308 (5726): 1263–1264. doi:10.1126/science.1113090. ISSN   0036-8075. PMID   15919979. S2CID   129749450.
  3. ↑ "Jet fuel consumption by country, around the world". TheGlobalEconomy.com. Retrieved June 26, 2021.
  4. ↑ Tilley, John (April 1814). "LIX. Description of a hydro-pneumatic blow-pipe for the use of chemists, enamellers, assayers, and glass-blowers". The Philosophical Magazine. 43 (192): 280–284. doi:10.1080/14786441408638024.
  5. ↑
  6. ↑ "The Petroleum Trail". Archived from the original on August 28, 2009.
  7. ↑ "Lukasiewicz, Ignacy". Encyclopedia of World Biography. Encyclopedia.com.
  8. ↑ "Pharmacist Introduces Kerosene Lamp, Saves Whales". History Channel. Archived from the original on June 9, 2019. Retrieved June 9, 2019.
  9. ↑ "Ignacy Łukasiewicz (1822–1882) – Polish pharmacist and Prometheus". polska.pl. Polish Ministry of Foreign Affairs.
  10. ↑ "Coleman US lanterns 1914 – 1920". The Terrence Marsh Lantern Gallery. January 25, 2018. Retrieved November 10, 2022.
  11. ↑ Bebb, Frank. "How to date your Coleman® Lamp, Lantern and Stove". The Old Town Coleman Center. Retrieved November 10, 2022.
  12. ↑ "Our Story". Coleman. Retrieved November 10, 2022.
  13. ↑ "Tilley Lamp Co". Grace's Guide To British Industrial History . Retrieved November 10, 2022.
  14. ↑ "Side Draft vs Center Draft Lamp, an explanation". YouTube: The wick shop . Retrieved October 21, 2024.
  15. ↑ The round burner https://artoluys.com/index.php/en/paraffin-kerosene-burners/the-kosmos-burner
  16. ↑ "Aladdin Kerosene Lamps". aladdinlamps.info. Retrieved June 8, 2021.
  17. ↑ Dennis L. Noble Lighthouses & Keepers: The U.S. Lighthouse Service and Its Legacy, Naval Institute Press, 2004 ISBN   1-59114-626-7, page 34.
  18. ↑ "Tubular Oil Lanterns — Frequently Asked Questions". W. T. Kirkman Lanterns, Inc. Archived from the original on October 29, 2013.
  19. ↑ USpatent 89770,John H. Irwin,"Improvement in lanterns",issued 1869-05-04
  20. 1 2 USpatent 138654,John H. Irwin,"Improvement in lamps",issued 1873-05-06
  21. ↑ Shepherd, Joseph E.; Perez, Frank A. (April 2008). "Kerosene lamps and cookstoves—The hazards of gasoline contamination". Fire Safety Journal. 43 (3): 171–179. doi:10.1016/j.firesaf.2007.08.001.
  22. ↑ World Health Organization (2016). Burning opportunity : clean household energy for health, sustainable development, and wellbeing of women and children. Geneva, Switzerland. p. X. Archived from the original on November 24, 2017.{{cite book}}: CS1 maint: location missing publisher (link)
  23. ↑ World Health Organization (2016). Burning opportunity : clean household energy for health, sustainable development, and wellbeing of women and children. Geneva, Switzerland. p. 49. Archived from the original on November 24, 2017.{{cite book}}: CS1 maint: location missing publisher (link)
  24. ↑ Narasimha Desirazu Rao Distributional Impacts of Energy Policies in India: Implications for Equity Stanford University, 2011 page 36.
  25. ↑ "Lumens to watts (W) conversion calculator". www.rapidtables.com. Retrieved August 27, 2017.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.