The log canoe is a type of sailboat developed in the Chesapeake Bay region. Based on the dugout, it was the principal traditional fishing boat of the bay until superseded by the bugeye and the skipjack. However, it is most famous as a racing sailboat, and races continue to be held.
The history of the log canoe is closely tied to the development of the oystering industry on the bay. In pre-power days, the log canoe was an inexpensive craft which could be assembled without recourse to shipbuilders; before the dredge was made legal in 1865, the log canoe was sufficient to the needs of oyster tongers. It did not have the pulling power necessary for dredging, however, its log construction was combined with characteristics of other vessels to form the first bugeyes, a much larger and more powerful vessel. As motor power became available, watermen who were not dredging gradually abandoned sail power; also, the supplies of suitable timber were gradually exhausted. Log canoes were often converted to motor power, and new workboats (such as the Chesapeake Bay deadrise) were motored from the start and used frame construction instead of logs. Many of the existing log canoes have suffered some conversion of this sort during their lifetimes.
Over the same period, however, the ad-hoc racing of canoes evolved into a semi-formal sport, and boats began being purpose-built for racing. From 1885 onward various clubs and associations sponsored organized races. This continues to the present, and racing canoes have been built as recently as 1974.
The typical log canoe is constructed from three to nine logs joined lengthwise and carved to form the lower portion of the hull. Additional height is obtained with smaller pieces fitted together and joined to the outermost (or "wing") logs. The resulting hull is sharp-sterned and shallow, and a centerboard is added which pierces the center (keel) log.
Details of construction, particularly at the stem and stern, varied over the region. Also, Virginia boat builders did not use models, whereas most Maryland builders would start from a half-model of the hull. Surviving log canoes range in length from 27 to 35 ft. on-deck. One example is the buyboat F.D. Crockett at the Deltaville Maritime Museum in Virginia. [1]
Rigging varied considerably.
Log canoes had one or two masts. Two-masted boats on the Chesapeake—not just log canoes—were often provided with a mast step to allow sailing with just one of the two sails.[ clarification needed ]
Typical later log canoes were two-masted, vaguely resembling a modern ketch rig. The masts were always steeply raked and unstayed, and the jib was flown from a bowsprit. The rigging of the sails themselves took several characteristic and unusual forms called a triangular "sprit-boomed leg-of-mutton." The main and fore sail were not attached to the boom at the foot, but instead attached only at the clew. A tackle attached to the mast provided the force necessary to shape the sail. One advantage of the sprit boom is that the sail is self-vanging, that is, the boom does not rise or fall depending on the set of the sail. The sheeting force is less, because the sheet does not have to supply downward pull to control the boom as with a gaff-rigged boat.
This evolved further to the "goosewing" form, in which the sail became trapezoidal. The pointed clew was replaced by a vertical spar, called a club. The club attached to the aft end of the boom. This allowed for more sail area between the masts than for a triangular sail.
The rigging of the jib was similarly unusual, but followed 19th century working-boat practice. There are several terms for a jib with a boom on the foot: balanced jib, club-footed jib, and self-tending jib.
On a club-footed jib, the foot was attached on a spar, and the balance point of this spar[ where? ] attached to the end of the bowsprit with a line or fixture. This allowed for a larger jib which could serve as something akin to a spinnaker when running.
Working sailors were less worried about the spinnaker effect than the fact that a properly trimmed balanced jib doesn't need any quick sheeting when tacking: hence the term "self-tending."
A final characteristic feature was the use of hiking boards to keep the boat from overturning. These were long, flat boards which hooked at one end under the cockpit and stuck sideways over the opposite gunwale. Crewmembers climb out onto these boards to counterbalance the force of the sails, thus preventing the boat from heeling over. These were particularly important to racing canoes, whose sail area and lack of ballast made them hopelessly tender without such counterbalancing.
A sailing vessel's rig is its arrangement of masts, sails and rigging. Examples include a schooner rig, cutter rig, junk rig, etc. A rig may be broadly categorized as "fore-and-aft", "square", or a combination of both. Within the fore-and-aft category there is a variety of triangular and quadrilateral sail shapes. Spars or battens may be used to help shape a given kind of sail. Each rig may be described with a sail plan—formally, a drawing of a vessel, viewed from the side.
A jibe (US) or gybe (Britain) is a sailing maneuver whereby a sailing craft reaching downwind turns its stern through the wind, which then exerts its force from the opposite side of the vessel. It stands in contrast with tacking, whereby the sailing craft turns its bow through the wind.
A spinnaker is a sail designed specifically for sailing off the wind on courses between a reach to downwind. Spinnakers are constructed of lightweight fabric, usually nylon, and are often brightly colored. They may be designed to perform best as either a reaching or a running spinnaker, by the shaping of the panels and seams. They are attached at only three points and said to be flown.
A mainsail is a sail rigged on the main mast of a sailing vessel.
Gaff rig is a sailing rig in which the sail is four-cornered, fore-and-aft rigged, controlled at its peak and, usually, its entire head by a spar (pole) called the gaff. Because of the size and shape of the sail, a gaff rig will have running backstays rather than permanent backstays.
Running rigging is the rigging of a sailing vessel that is used for raising, lowering, shaping and controlling the sails on a sailing vessel—as opposed to the standing rigging, which supports the mast and bowsprit. Running rigging varies between vessels that are rigged fore and aft and those that are square-rigged.
Bermuda rig, Bermudian rig, or Marconi rig is a type of sailing rig that uses a triangular sail set abaft (behind) the mast. It is the typical configuration for most modern sailboats. Whilst commonly seen in sloop-rigged vessels, Bermuda rig is used in a range of configurations, for instance, a cutter or a schooner, and several other types.
Sail components include the features that define a sail's shape and function, plus its constituent parts from which it is manufactured. A sail may be classified in a variety of ways, including by its orientation to the vessel and its shape,. Sails are typically constructed out of flexible material that is shaped by various means, while in use, to offer an appropriate airfoil, according to the strength and apparent direction of the wind. A variety of features and fittings allow the sail to be attached to lines and spars.
The spritsail is a four-sided, fore-and-aft sail that is supported at its highest points by the mast and a diagonally running spar known as the sprit. The foot of the sail can be stretched by a boom or held loose-footed just by its sheets. A spritsail has four corners: the throat, peak, clew, and tack. The Spritsail can also be used to describe a rig that uses a spritsail.
The skipjack is a traditional fishing boat used on the Chesapeake Bay for oyster dredging. It is a sailboat which succeeded the bugeye as the chief oystering boat on the bay, and it remains in service due to laws restricting the use of powerboats in the Maryland state oyster fishery.
The 3000 is a racing sailing dinghy crewed by two persons with a trapeze for the crew. Launched in 1996 as the Laser 3000, the 3000 was developed from the Laser 2, using the original Frank Bethwaite-designed planing hull combined with a new designed self-draining deck by Derek Clark. Clark also re-designed the rig, using spars and sails from premium proprietary sources and replacing the symmetric spinnaker of the Laser 2 by a larger asymmetric spinnaker (gennaker). The gennaker is chute-launched and retrieved using a single halyard line, and is set on a retractable bowsprit. Helm balance and handling were improved using a shorter-footed mainsail with two full-width battens giving a larger roach. A mast with conventional spreaders replaced the now-unusual diamond arrangement of the Laser 2.
The Bermuda Fitted Dinghy is a type of racing-dedicated sail boat used for competitions between the yacht clubs of Bermuda. Although the class has only existed for about 130 years, the boats are a continuance of a tradition of boat and ship design in Bermuda that stretches back to the earliest decades of the 17th century.
The pungy is a type of schooner developed in and peculiar to the Chesapeake Bay region. The name is believed to derive from the Pungoteague region of Accomack County, Virginia, where the design was developed in the 1840s and 1850s.
An asymmetrical spinnaker is a sail used when sailing between about 90 and 165 degrees from the angle of the wind. Also known as an "asym", "aspin", "A-sail", or gennaker, it can be described as a cross between a genoa (jib) and a spinnaker. It is asymmetric like a genoa, but like a spinnaker, its luff is unstructured and floats freely, unencumbered by an internal wire or hanks attaching it to a stay. Unlike a symmetric spinnaker, the asymmetric does not require a spinnaker pole, since it is fixed (tacked) to the bow or a bowsprit.
The bugeye is a type of sailboat developed in the Chesapeake Bay for oyster dredging. The predecessor of the skipjack, it was superseded by the latter as oyster harvests dropped.
The Edna E. Lockwood is a Chesapeake Bay bugeye, the last working oyster boat of her kind. She is located at the Chesapeake Bay Maritime Museum in Saint Michaels, Maryland. She was built in 1889 at Tilghman Island, Maryland by John B. Harrison and is of nine-log construction, similar to the smaller log canoe, and was launched on October 5, 1889, for Daniel Haddaway, at a cost of $2,200. She worked for at least seven sets of owners from 1899 until 1967, and was then sailed as a yacht until donated to the museum in 1973. The museum undertook an extensive restoration of the Lockwood from 1975 through 1979, which restored the bugeye to its 1910 appearance with the "patent stern" that had been added sometime prior to that year. She is the last bugeye retaining the sailing rig and working appearance of the type. Her length is 53.5 feet (16.3 m), with a 15.25 feet (4.65 m) beam and a draft of 2.58 feet (0.79 m) with the centerboard up, and a maximum sail area of approximately 1700 square feet.
The Rebecca T. Ruark is a Chesapeake Bay skipjack built at Taylor's Island, Maryland. She is homeported at Tilghman Island, Maryland. Built in 1896, she is the oldest surviving skipjack in the Chesapeake Bay fleet. She was designated a National Historic Landmark in 2003.
A jibboom is a spar used to extend the length of a bowsprit on sailing ships. It can itself be extended further by a flying jib-boom. The heel end of the flying jib-boom is attached to the jib-boom, and the heel of the jib-boom to the bowsprit. The point of the flying jib-boom is generally the fore-most extent of a ship. The jib- and flying jib- booms carry the tacks of the jib and flying jib sails, respectively, and the stay for the fore topgallant mast and the royal stay.
A sail is a tensile structure, which is made from fabric or other membrane materials, that uses wind power to propel sailing craft, including sailing ships, sailboats, windsurfers, ice boats, and even sail-powered land vehicles. Sails may be made from a combination of woven materials—including canvas or polyester cloth, laminated membranes or bonded filaments, usually in a three- or four-sided shape.
The following outline is provided as an overview of and topical guide to sailing:
| Fisheries |  | |
|---|---|---|
| Fishing | ||
| Industry | ||
| Recreation | ||
| Techniques | ||
| Tackle | ||
| Locations | ||
