Ordnance QF 2-pounder

Last updated • 10 min readFrom Wikipedia, The Free Encyclopedia

Ordnance QF 2 pounder
The British Army in the United Kingdom 1939-45 H23836.jpg
QF 2 pounder set up for firing; the gun commander stands behind the gun and the third crewmember would fetch ammunition.
Type Tank gun
Anti-tank gun
Place of originUnited Kingdom
Service history
In service1936–1945
Used byUnited Kingdom
Australia
Ireland
Germany
Egypt
Malaysia
Wars Spanish Civil War [1]
World War II
1948 Arab–Israeli War [2]
Production history
Designed1936
Manufacturer Vickers-Armstrongs
Produced1936–1944
No. built12,000 [3]
Specifications (on Carriage Mk II)
Mass1,795 lb (814 kg)
Barrel  lengthoverall: 6 ft 10 in (2.08 m) L/52 [a]
Width59.25 in (1.505 m)
Height55.15 in (1.401 m)
Crew3–5 [3]

Shell 40×304mmR [5]
Calibre 40 mm (1.575 in)
Breech Semi-automatic vertical sliding-block
Recoil Hydro-spring
Carriagethree-leg platform
Elevation -13° to +15°
Traverse 360°
Rate of fire 22 rounds per minute
Muzzle velocity 2,600 ft/s (792 m/s) with AP shot
Effective firing range1,500 yd (1,400 m) [6]
Maximum firing range1,800 yd (1,600 m) [7] [ page needed ]
Feed system Breech-loaded
SightsNo.24b

The Ordnance QF 2-pounder (QF denoting "quick firing"), or simply "2 pounder gun", was a 40 mm (1.575 in) British anti-tank gun and vehicle-mounted gun employed in the Second World War.

Contents

It was the main anti-tank weapon of the artillery units in the Battle of France and, due to the need to rearm quickly after the Dunkirk evacuation, remained in service during the North African campaign. In its vehicle-mounted variant the 2-pounder was a common main gun on British tanks early in World War II, as well as being a typical main armament of armoured cars, such as the Daimler, throughout the war. As the armour protection of Axis tanks improved, the 2-pounder lost effectiveness and it was gradually replaced by the 57 mm QF 6-pounder starting in 1942. It equipped infantry battalion anti-tank platoons replacing their anti-tank rifles until in turn replaced by 6-pounders but remained in service until the end of the war.

This QF 2-pounder was distinctly different from the QF 2 pounder "pom-pom" gun naval anti-aircraft gun used by the Royal Navy which was a 40 mm autocannon.

History

The gun was developed as both a tank weapon and an anti-tank gun. For reasons of economy and standardization, it was accepted - as the 2-pdr Mark IX - for both purposes in October 1935. Carriages for the gun were designed by Vickers and the Design Department at the Woolwich Arsenal. [8]

Mark I carriage, April 1941 The British Army in the United Kingdom 1939-45 H9102.jpg
Mark I carriage, April 1941

Vickers was the first to submit a design, which was accepted as the 'Ordnance QF 2-pounder Mark IX on Carriage Mark I'. A limited number of pieces were built in 1936. The carriage had an innovative three-legged construction. In the travelling position, one of the legs was used as a towing trail, and the other two were folded. When the gun was positioned for combat, the legs were emplaced on the ground and the wheels were lifted up. Woolwich Arsenal had continued to develop their carriage and when re-examined was seen to be superior to Vickers design, and with this carriage the gun was adopted as 'Ordnance QF 2-pounder Mark IX on Carriage Mark II'. It was conceptually similar, although the wheels had to be removed when the gun was emplaced for combat. This carriage was also manufactured by Vickers. [8]

The unusual construction gave the gun good stability and a traverse of 360 degrees, allowing it to quickly engage moving vehicles from any approach. The gunner had handwheels for traverse and elevation. Additionally, he could disengage the traverse mechanism and the gun commander could rotate the gun by pushing against the gunners shoulders. The commander was aided by a simple ring and bead sight on the top of the shield. The gunner had a 1.9x magnification telescopic sight with a 21 degree field of view, graduated from 600 yd (550 m) to 1,800 yd (1,600 m) at 300 yd intervals. [7] The gunner also had a notch and bead sight above the telescopic [9]

With the Vickers carriage, the gun could also be fired from its wheels, at the expense of limited traverse. The shield was 5/16 inch armour plate. Typically it was towed by a 15-cwt (3/4-ton) truck [b] with 68 rounds on the truck with a further 14 on the carriage itself. [9] It could also be carried "portee" on a 30-cwt truck.

The 40 mm 2-pounder could outperform[ citation needed ] a typical 37 mm piece, such as the German 3.7 cm PaK 36 or the Bofors 37 mm, and significantly outclassed 25mm and 20mm weapons of that era. A drawback of the 2-pounder was that it was nearly twice as heavy as the PaK 36 and had a higher profile.[ citation needed ]

The gun was first put into use on armoured fighting vehicles as the main armament of the new lines of cruiser and infantry tanks - the Cruiser Mk I and the Matilda II which entered production in 1937. The Light Tank Mk VII designed in 1937 also had the gun, as did the Daimler armoured car developed in the following years.

To improve performance a squeeze bore system was developed. The Littlejohn adaptor which screwed onto the end of the gun's barrel was used with Armour-piercing, composite non-rigid (APCNR) ammunition. The round fired a light alloy carrier surrounding a heavy tungsten shot; as it passed through the tapered barrel of the adaptor, the carrier was squeezed from 40 mm to 30 mm diameter. The reduction in cross-sectional area increased the driving force and therefore the velocity of the round taking penetration from 52 mm to 88 mm. [10]

A late-war project was the Canadian David High Velocity to allow 2-pdr ammunition to be fired from the larger-calibre 6-pdr. This was intended to improve the muzzle velocity of the shot. Initial trials carried out in Canada and the U.K. were promising; [11] however the system was still being developed when the war ended, and the program was subsequently ended along with it.

Another development was the 2-pdr HV 'Pipsqueak', a postwar gun using a 40x438R cartridge originally intended as the main armament for the Alvis Saladin armoured car that was to replace the AEC armoured car. This was designed to fire Armour-Piercing Discarding Sabot (APDS) rounds, which would match the penetration of the 'Littlejohn adaptor' shot while still allowing high-explosive (HE) shells to be fired. The claimed performance was better, the 1,295 m/s (4,250 ft/s) shot penetrating 85 mm (3.3 in) of armour at 60 degrees at 900 m (980 yd). Development of this gun was also abandoned when the role of the Saladin shifted towards infantry fire support, and a low-velocity 76 mm gun was selected for it instead.[ citation needed ]

Initially one of the most serious shortcomings of the 2-pdr was the lack of a high-explosive shell resulting from the British doctrine, especially when the 2-pdr was the main gun of a tank; this was very important when a tank was being used for infantry support, intentionally leaving it with only its machine gun for anti-personnel use. The doctrine was slow to change even in the light of battlefield experience,[ according to whom? ] and the high-explosive shell was not produced until late 1942. [12]

Service history

Crew inside a Valentine tank loading the gun Loading Valentine tank 2 pdr gun IWM E 9766.jpg
Crew inside a Valentine tank loading the gun
2 pounder in action, legs unfolded, with British troops 2-pounder gun.jpg
2 pounder in action, legs unfolded, with British troops
Australian 2 pounder crew firing on Japanese tanks at point-blank range in the Battle of Muar Australian 2-pdr anti-tank gun in action at Bakri on the Muar-Parit Sulong Road.jpg
Australian 2 pounder crew firing on Japanese tanks at point-blank range in the Battle of Muar
Type 95 Ha-Go tanks, victims of the Australian 2 pounder gun (see above image) Type 95 Ha-Go tank Malaya AWM 011298.jpg
Type 95 Ha-Go tanks, victims of the Australian 2 pounder gun (see above image)

The 2-pdr gun became a part of the Royal Artillery in 1938, when five field brigades were converted to anti-tank regiments. [13] In the early western campaigns, the 2-pdr was employed by two types of Royal Artillery formations: anti-tank regiments of infantry divisions (four batteries with 12 pieces each), and light anti-aircraft/anti-tank regiments of armoured divisions (two 12-gun AT batteries). From October 1940, separate 48-gun anti-tank regiments were introduced in armoured divisions too. Infantry brigade structure initially included an anti-tank company, though it was typically equipped with 25 mm Hotchkiss anti-tank guns; these companies were disbanded later in the war. From 1942, infantry battalions received their own six-gun anti-tank platoons. The organization was different in the Far East theatres. The exact internal structure of AT units was also subject to changes and variations.

The gun first saw combat with the British Expeditionary Force (World War II) during the German invasion of the Low Countries and the subsequent rear-guard actions at Dunkirk. Most of the British Army's 2-pdrs were left behind in France during the retreat, stripping most of the army's infantry anti-tank capability. Those guns captured at Dunkirk entered German service under the designation 4.0 cm Pak 192 (e) or 4.0 cm Pak 154 (b), the "e" and "b" referring to the origin (English or mistakenly attributed to the Belgian Army).

Although Woolwich Arsenal had already designed a successor to the 2-pdr, the 6 pounder gun, it was decided in the face of a possible German invasion to re-equip the army with the 2-pdr, avoiding the period of adaptation to production, and also of re-training and acclimatization with the new weapon. Consequently, 6 pounder production was delayed until November 1941 and frontline availability until spring 1942. Thus during most of the North African Campaign the army had to rely on the 2-pdr, augmented by the 25 pounder gun-howitzer functioning as an anti-tank gun—a role for which it was capable (at the expense of diverting it from its main artillery role). As German tank design evolved, anti-armour performance of the 2-pdr gradually became insufficient; however, the gun owes a large part of the bad reputation it gained during the campaign to the open terrain, which made the high-silhouette piece hard to conceal, and to poor tactics.[ citation needed ]

In North Africa, it was found that the 2-pdr was damaged by being towed long distances across rough, stony deserts. Starting in 1941, the British developed the "en portee" method of mounting the 2-pdr, and later the 6-pounder, on a truck. Though only intended for transport, with the gun carried unloaded, crews tended to fire from their vehicles for more mobility, with consequent casualties. Hence the vehicles tended to reverse into action so that the gunshield of the 2-pdr would provide a measure of protection against enemy fire. An infantry battalion anti-tank platoon would have eight guns on 3-ton lorries [14] On 21 November 1941 during battle of Sidi Rezegh Second lieutenant George Ward Gunn J Battery Royal Horse Artillery was earned the Victoria Cross for his action with a 2-pdr. The troop of four portee 2-pdrs under his command engaged a German counter-attack of about 60 tanks. Three of the guns were knocked out, and all bar one gunner killed or fatally wounded. Despite the truck being on fire, Gunn manned the gun himself with a sergeant as his loader, engaging the enemy at 800 yards, he fired 40-50 rounds knocking out two tanks and damaging others before he was killed. [15] The battery commander then took over.

From mid-1942, the 2-pdr was increasingly displaced to infantry anti-tank platoons, to Home Guard units in Great Britain, and to the Far East, where it was still effective against the smaller and more lightly armoured Japanese tanks. It was finally removed from service entirely in December 1945. As a vehicle weapon, it remained in use throughout the war. Although most tanks equipped with it were withdrawn or upgraded to the 6-pdr, it remained in use with armoured cars.

Its performance as an anti-armour weapon was improved later in the war with the development of more sophisticated ammunition and got an additional boost with the introduction of the Littlejohn adaptor, which converted it to a squeeze-bore design firing specially-designed shells at much higher velocities. However, the Littlejohn adaptor prevented the use of High Explosive rounds. These improvements, however, were constantly outpaced by improvements in tank design.

As a tank gun, used stationary the effective range was out to 1500 yds. [6]

Ammunition

Available ammunition [16] [17] [18]
TypeModelShot/shellRound weightProjectile weightFillerMuzzle velocity
Armour-piercing, tracer Shell AP/T Mk IT Shell 2.375 lb (1.077 kg)11 drachms (19 g) Lyddite 807 m/s (2,650 ft/s)
Armour-piercing, tracer AP/T Mk I Shot 2.04 kg (4.5 lb)1.08 kg (2.4 lb)792 m/s (2,600 ft/s)
Armour-piercing, tracer, increased chargeAPHV/TShot2.04 kg (4.5 lb)1.08 kg (2.4 lb)-853 m/s (2,800 ft/s)
Armour-piercing, capped, ballistic cap, tracerAPCBC/T Mk IShot2.22 kg (4.9 lb)1.22 kg (2.7 lb)-792 m/s (2,600 ft/s)
Armour-piercing, composite non-rigid
(used with the Littlejohn adaptor)
AP/CNR (APSV [c] ) Mk IShot?1.037 lb (0.470 kg)-1,280 m/s (4,200 ft/s)
Armour-piercing, composite non-rigid
(used with the Littlejohn adaptor)
AP/CNR (APSV) Mk IIShot?1.234 lb (0.560 kg)-1,189 m/s (3,900 ft/s)
Practice, tracer [7] Shot, Practice, Mk ITFlathead Shot2.375 lb (1.077 kg)-610 m/s (2,000 ft/s)
High-explosive, tracerHE/T Mk II Shell 1.86 kg (4.1 lb)0.86 kg (1.9 lb)3 oz (85 g) TNT or RDX 792 m/s (2,600 ft/s)
Estimated armour penetration (mm) [19] [d] [ failed verification ]
Distance100 yd (91 m)500 yd (457 m)1,000 yd (914 m)1,499 yd (1,371 m)
AP (meet angle 30°)53474034
APHV (meet angle 30°)105907460
APCBC (meet angle 30°)58534944

Variants

Gun variants: [20]

Carriage variants:

Self-propelled mounts

Matilda II Matilda Compass.jpg
Matilda II
Australian 2 pounder anti-tank gun carrier 2 pdr Aust ATG carrier(AWM 134672).jpg
Australian 2 pounder anti-tank gun carrier
Tanks
Armoured cars
Other vehicles

Surviving examples

See also

Notes

  1. rifling was 5 ft 6 in (1.68 m) [4]
  2. 15 hundredweight was the nominal carrying capacity of the vehicle. The Morris CS8 and Fordson WOT2 were typical of the type.
  3. "armour piercing super velocity"
  4. Different methods of armour penetration measurement were used in different countries / periods. Therefore, direct comparison is often impossible

Related Research Articles

<span class="mw-page-title-main">Tank destroyer</span> Armoured fighting vehicle designed to engage and destroy enemy tanks

A tank destroyer, tank hunter or tank killer is a type of armoured fighting vehicle, predominantly intended for anti-tank duties. They are typically armed with a direct fire artillery gun, also known as a self-propelled anti-tank gun, or missile launcher, also called an anti-tank missile carrier. The vehicles are designed specifically to engage and destroy enemy tanks, often with limited operational capacities.

<span class="mw-page-title-main">Cromwell tank</span> British WWII cruiser tank

The Cromwell tank, officially Tank, Cruiser, Mk VIII, Cromwell (A27M), was one of the series of cruiser tanks fielded by Britain in the Second World War. Named after the English Civil War–era military leader Oliver Cromwell, the Cromwell was the first tank put into service by the British to combine high speed from a powerful, reliable engine and reasonable armour. The intended dual-purpose high-velocity gun could not be fitted in the turret, so a medium-velocity dual-purpose gun was fitted instead. Further development of the Cromwell combined with a high-velocity gun led to the Comet tank.

<span class="mw-page-title-main">Crusader tank</span> British WWII cruiser tank

Crusader, in full "Tank, Cruiser Mk VI, Crusader", also known by its General Staff number A.15, was one of the primary British cruiser tanks during the early part of the Second World War. Over 5,000 tanks were manufactured and they made important contributions to the British victories during the North African campaign. The Crusader only saw active service in Africa but the chassis of the tank was modified to create anti-aircraft, fire support, observation, communication, bulldozer and recovery vehicle variants.

<span class="mw-page-title-main">Cruiser Mk I</span> British cruiser tank

The Tank, Cruiser, Mk I (A9) was a British cruiser tank of the interwar period. It was the first cruiser tank: a fast tank designed to bypass the main enemy lines and engage the enemy's lines of communication, as well as enemy tanks. The Cruiser Mk II was a more heavily armoured adaptation of the Mark I, developed at much the same time.

<span class="mw-page-title-main">Cruiser Mk II</span> British cruiser tank

The Tank, Cruiser, Mk II (A10), was a cruiser tank developed alongside the A9 cruiser tank, and was intended to be a heavier, infantry tank version of that type. In practice, it was not deemed suitable for the infantry tank role and was classified as a "heavy cruiser". It served briefly in World War II.

<span class="mw-page-title-main">Comet (tank)</span> British cruiser tank

The Comet tank or Tank, Cruiser, Comet I (A34) was a British cruiser tank that first saw use near the end of the Second World War, during the Western Allied invasion of Germany. The Comet was developed from the earlier Cromwell tank with a lower profile, partly-cast turret which mounted the new 77 mm HV gun. This was a smaller version of the 17 pdr anti-tank gun firing the same 76.2 mm (3") projectiles, albeit with a lighter charge, and was effective against late-war German tanks, including the Panther and Tiger.

<span class="mw-page-title-main">Archer (tank destroyer)</span> British self-propelled anti-tank gun

The self-propelled 17-pdr, Valentine, Mk I, Archer was a British tank destroyer of the Second World War based on the Valentine infantry tank chassis fitted with an Ordnance QF 17 pounder gun. Designed and manufactured by Vickers-Armstrongs, 655 were produced between March 1943 and May 1945. It was used in north-west Europe and Italy during the war; post-war, it served with the Egyptian Army. This vehicle was unusual in that its gun faced the rear of the chassis instead of the front.

<span class="mw-page-title-main">Ordnance QF 17-pounder</span> Anti-tank gun and tank gun

The Ordnance Quick-Firing 17-pounder was a 76.2 mm (3 inch) gun developed by the United Kingdom during World War II. It was used as an anti-tank gun on its own carriage, as well as equipping a number of British tanks. Used with the APDS shot, it was capable of defeating all but the thickest armour on German tanks. It was used to "up-gun" some foreign-built vehicles in British service, notably to produce the Sherman Firefly variant of the US M4 Sherman tank, giving British tank units the ability to hold their own against their German counterparts. In the anti-tank role, it was replaced after the war by the 120 mm BAT recoilless rifle. As a tank gun, it was succeeded by the 84 mm 20 pounder.

<span class="mw-page-title-main">Cruiser tank</span> Class of tank

The cruiser tank was a British tank concept of the interwar period for tanks designed as modernised armoured and mechanised cavalry, as distinguished from infantry tanks. Cruiser tanks were developed after medium tank designs of the 1930s failed to satisfy the Royal Armoured Corps. The cruiser tank concept was conceived by Giffard Le Quesne Martel, who preferred many small light tanks to swarm an opponent, instead of a few expensive and unsatisfactory medium tanks. "Light" cruiser tanks carried less armour and were correspondingly faster, whilst "heavy" cruiser tanks had more armour and were slightly slower.

<span class="mw-page-title-main">Infantry tank</span> Class of tank

The infantry tank was a tank concept developed by the United Kingdom and France in the years leading up to World War II. Infantry tanks were designed to support infantrymen in an attack. To achieve this, the vehicles were generally heavily armoured to allow them to operate in close concert with infantry even under heavy fire. The extra armour came at the expense of speed, which was not an issue when supporting relatively slow-moving foot soldiers.

<span class="mw-page-title-main">Ordnance QF 25-pounder</span> British field gun and gun-howitzer used during the Second World War

The Ordnance QF 25-pounder, or more simply 25-pounder or 25-pdr, with a calibre of 3.45 inches (87.6 mm), was a piece of field artillery used by British and Commonwealth forces in the Second World War. Durable, easy to operate and versatile, it was the most produced and used British field gun and gun-howitzer during the war.

<span class="mw-page-title-main">QF 2-pounder naval gun</span> British naval gun

The 2-pounder gun, officially the QF 2-pounder and universally known as the pom-pom, was a 40 mm (1.6 in) British autocannon, used as an anti-aircraft gun by the Royal Navy. The name came from the sound that the original models make when firing. This QF 2-pounder was not the same gun as the Ordnance QF 2-pounder, used by the British Army as an anti-tank gun and a tank gun, although they both fired 2 lb (0.91 kg), 40 mm (1.6 in) projectiles.

<span class="mw-page-title-main">Ordnance QF 6-pounder</span> British anti-tank gun

The Ordnance quick-firing 6-pounder 7 cwt, or just 6-pounder, was a British 57 mm gun, serving during the Second World War as a primary anti-tank gun of both the British and United States Army. It was also used as the main armament for a number of armoured fighting vehicles.

<span class="mw-page-title-main">Littlejohn adaptor</span>

The Littlejohn adaptor was a device that could be added to the British QF 2 pounder (40 mm) anti-tank gun. It was used to extend the service life of the 2-pounder during the Second World War by converting it to squeeze bore operation. "Littlejohn" came from the calque, i.e. literal anglicization, of the name of František Janeček, the Czech designer and factory owner who had been working on the squeeze-bore principle in the 1930s and his son František Karel Janeček, who had brought his know-how to Britain after fleeing from German-occupied Czechoslovakia.

This article lists British armoured fighting vehicle production during the Second World War. The United Kingdom produced 27,528 tanks and self-propelled guns from July 1939 to May 1945, as well as 26,191 armoured cars and 69,071 armoured personnel carriers.

The British Army made extensive use of a variety of combat vehicles during the Second World War. This article is a summary of those vehicles.

<span class="mw-page-title-main">Ordnance QF 32-pounder</span> Gun

The Ordnance QF 32 pounder or (32-pdr) was a British 94 mm gun, initially developed as a replacement for the Ordnance QF 17-pdr anti-tank gun.

<span class="mw-page-title-main">17pdr SP Achilles</span> British self-propelled anti-tank gun

The 17pdr SP Achilles is a British variant of the American M10 tank destroyer armed with the British Ordnance QF 17-pounder high-velocity 76.2 mm (3-inch) anti-tank gun in place of the M10's considerably less powerful 3-inch Gun M7. A total of 1,100 M10s were converted to Achilles, making it the second most numerous armoured fighting vehicle to carry the 17-pounder gun, behind the Sherman Firefly tank.

<span class="mw-page-title-main">Tanks in the British Army</span> Evolution of British tanks

This article on military tanks deals with the history and development of tanks of the British Army from their first use in the First World War, the interwar period, during the Second World War, the Cold War and modern era.

References

Notes
  1. Bishop, Chris (1998). The Encyclopedia of Weapons of World War II . New York: Barnes & Noble Books. p.  180. ISBN   0760710228. OCLC   40924461.
  2. Russell, Lee; Katz, Sam (April 1986). Israeli Defense Forces, 1948 to the Present. Uniforms Illustrated 12. Olympic Marketing Corp. p. 6. ISBN   978-0853687559.
  3. 1 2 "Ordnance QF 2-pounder Anti-Tank Gun". Military Factory. 29 September 2018. Archived from the original on 29 April 2021. Retrieved 5 February 2013.
  4. Boyd
  5. "The 2 Pounder Anti-Tank Gun", The Armourer's Bench, 10 March 2019, archived from the original on 13 April 2021, retrieved 19 September 2021
  6. 1 2 Mobile Division Training Pamphlet No. 2, Notes on the Employment of the Tank Brigade, War Office, 1938, p. 30
  7. 1 2 3 Handbook for the Ordnance, Q.F., 2-Pr Marks IX and X on Carriages, Q.F. 2-Pr., Marks I and II Land Service 1938
  8. 1 2 Henry 2004, p. 6–7.
  9. 1 2 TM 30-410: Handbook on the British army : with supplements on the Royal Air Force and civilian defense organizations, War Department, 30 September 1942, p. 150-151
  10. Williams, Antony G. "The Vickers 40mm S Gun With Littlejohn Adaptor". quarryhs.co.uk. Archived from the original on 16 April 2017. Retrieved 17 June 2023.
  11. Fulton, Colonel F.F. (ed.), "Artillery, Anti-tank, Q.F. 2-pounder High Velocity "David" Firing and travelling trials", Canadian Military Headquarters, London (CMHQ), Files Block No. 55 - 5792, Library and Archives Canada / Bibliothèque et Archives Canada, pp. 1614–36, archived from the original on 5 April 2024, retrieved 31 December 2022
  12. Boyd, David (1 January 2009). "The 2 Pounder Anti-Tank Gun". WWII Equipment. Archived from the original on 3 April 2022.
  13. Henry 2004, p. 39.
  14. "British Infantry battalion (Middle East)" (PDF), Bayonetstrength.uk, p. 8, archived (PDF) from the original on 28 November 2022, retrieved 19 September 2021, citing War establishment reference VI/547/1 effective April 1942
  15. "No. 35530". The London Gazette (Supplement). 17 April 1942. p. 1741.
  16. Regulations for Army Ordnance Services Volume 4 Ammunition Pamphlet No. 8 Q.F. Fixed Ammunition Amendments No. 20 Part 2 Cartridge, Q.F., 2-pr., Mks. 9A and 10A Guns and Cartridge, Q.F., 2-pr., S.V., Mk. 10B Gun 1956
  17. Hunnicutt 1994, p. 496.
  18. Guns vs Armour 1939 to 1945.
  19. Bird, Lorrin; Livingston, Robert (2001). World War II Ballistics: Armor and Gunnery. Albany, NY: Overmatch Press. p. 60. OCLC   71143143.
  20. Henry 2004.
  21. Chamberlain, & Gander 1974, p. 38.
  22. "2 Pounder Anti-Tank Gun". www.awm.gov.au. Archived from the original on 24 September 2019. Retrieved 24 September 2019.
Bibliography

Further reading