Austempering

Last updated
Time-temperature transformation (TTT) diagram. The red line shows the cooling curve for austempering. Austempering.jpg
Time-temperature transformation (TTT) diagram. The red line shows the cooling curve for austempering.

Austempering is heat treatment that is applied to ferrous metals, most notably steel and ductile iron. In steel it produces a bainite microstructure whereas in cast irons it produces a structure of acicular ferrite and high carbon, stabilized austenite known as ausferrite. It is primarily used to improve mechanical properties or reduce / eliminate distortion. Austempering is defined by both the process and the resultant microstructure. Typical austempering process parameters applied to an unsuitable material will not result in the formation of bainite or ausferrite and thus the final product will not be called austempered. Both microstructures may also be produced via other methods. For example, they may be produced as-cast or air cooled with the proper alloy content. These materials are also not referred to as austempered.

Contents

History

The austempering of steel was first pioneered in the 1930s by Edgar C. Bain and Edmund S. Davenport, who were working for the United States Steel Corporation at that time. Bainite must have been present in steels long before its acknowledged discovery date, but was not identified because of the limited metallographic techniques available and the mixed microstructures formed by the heat treatment practices of the time. Coincidental circumstances inspired Bain to study isothermal phase transformations. Austenite and the higher temperature phases of steel were becoming more and more understood and it was already known that austenite could be retained at room temperature. Through his contacts at the American Steel and Wire Company, Bain was aware of isothermal transformations being used in industry and he began to conceive new experiments [1]

Further research into the isothermal transformation of steels was a result of Bain and Davenport's discovery of a new microstructure consisting of an "acicular, dark etching aggregate." This microstructure was found to be "tougher for the same hardness than tempered Martensite". [2] Commercial exploitation of bainitic steel was not rapid. Common heat-treating practices at the time featured continuous cooling methods and were not capable, in practice, of producing fully bainitic microstructures. The range of alloys available produced either mixed microstructures or excessive amounts of Martensite. The advent of low-carbon steels containing boron and molybdenum in 1958 allowed fully bainitic steel to be produced by continuous cooling. [1] [3] Commercial use of bainitic steel thus came about as a result of the development of new heat-treating methods, with those that involve a step in which the workpiece is held at a fixed temperature for a period of time sufficient to allow transformation becoming collectively known as austempering.

One of the first uses of austempered steel was in rifle bolts during World War II. [4] The high impact strength possible at high hardnesses, and the relatively small section size of the components made austempered steel ideal for this application. Over subsequent decades austempering revolutionized the spring industry followed by clips and clamps. These components, which are usually thin, formed parts, do not require expensive alloys and generally possess better elastic properties than their tempered Martensite counterparts. Eventually austempered steel made its way into the automotive industry, where one of its first uses was in safety critical components. The majority of car seat brackets and seat belt components are made of austempered steel because of its high strength and ductility. [4] These properties allow it to absorb more energy during a crash without the risk of brittle failure. Currently, austempered steel is also used in bearings, mower blades, transmission gear, wave plate, and turf aeration tines. [4] In the second half of the 20th century the austempering process began to be applied commercially to cast irons. Austempered ductile iron (ADI) was first commercialized in the early 1970s and has since become a major industry.

Process

The most notable difference between austempering and conventional quench and tempering is that it involves holding the workpiece at the quenching temperature for an extended period of time. The basic steps are the same whether applied to cast iron or steel and are as follows:

Austenitizing

In order for any transformation to take place, the microstructure of the metal must be austenite structure. The exact boundaries of the austenite phase region depend on the chemistry of the alloy being heat treated. However, austenitizing temperatures are typically between 790 and 915 °C (1,454 and 1,679 °F). [5] The amount of time spent at this temperature will vary with the alloy and process specifics for a through-hardened part. The best results are achieved when austenitization is long enough to produce a fully austenitic metal microstructure (there will still be graphite present in cast irons) with a consistent carbon content. In steels this may take only a few minutes after the austenitizing temperature has been reached throughout the part section, but in cast irons it takes longer. This is because carbon must diffuse out of the graphite until it has reached the equilibrium concentration dictated by the temperature and the phase diagram. This step may be done in many types of furnaces, in a high-temperature salt bath, or via direct flame or induction heating. Numerous patents describe specific methods and variations.

Quenching

As with conventional quench and tempering the material being heat treated must be cooled from the austenitizing temperature quickly enough to avoid the formation of pearlite. The specific cooling rate that is necessary to avoid the formation of pearlite is a product of the chemistry of the austenite phase and thus the alloy being processed. The actual cooling rate is a product of both the quench severity, which is influenced by quench media, agitation, load (quenchant ratio, etc.), and the thickness and geometry of the part. As a result, heavier section components required greater hardenability. In austempering the heat treat load is quenched to a temperature which is typically above the Martensite start of the austenite and held. In some patented processes the parts are quenched just below the Martensite start so that the resulting microstructure is a controlled mixture of Martensite and Bainite.

The two important aspects of quenching are the cooling rate and the holding time. The most common practice is to quench into a bath of liquid nitrite-nitrate salt and hold in the bath. Because of the restricted temperature range for processing it is not usually possible to quench in water or brine, but high temperature oils are used for a narrow temperature range. Some processes feature quenching and then removal from the quench media, then holding in a furnace. The quench and holding temperature are primary processing parameters that control the final hardness, and thus properties of the material.

Cooling

After quenching and holding there is no danger of cracking; parts are typically air cooled or put directly into a room temperature wash system.

Tempering

No tempering is required after austempering if the part is through hardened and fully transformed to either Bainite or ausferrite. [5] Tempering adds another stage and thus cost to the process; it does not provide the same property modification and stress relief in Bainite or ausferrite that it does for virgin Martensite.

Advantages

Austempering offers many manufacturing and performance advantages over conventional material/process combinations. It may be applied to numerous materials, and each combination has its own advantages, which are listed below. One of the advantages that is common to all austempered materials is a lower rate of distortion than for quenching and tempering. This can be translated into cost savings by adjustment of the entire manufacturing process. The most immediate cost savings are realized by machining before heat treatment. There are many such savings possible in the specific case of converting a quench-and-tempered steel component to austempered ductile iron (ADI). Ductile iron is 10% less dense than steel and can be cast near to net shape, both characteristics that reduce the casting weight. Near-net-shape casting also further reduces the machining cost, which is already reduced by machining soft ductile iron instead of hardened steel. A lighter finished part reduces freight charges and the streamlined production flow often reduces lead time. In many cases strength and wear resistance can also be improved. [4]

Process/material combinations include:

With respect to performance improvements, austempered materials are typically compared to conventionally quench-and-tempered materials with a tempered Martensite microstructure.

In steels above 40 Rc these improvements include:

In cast irons (from 250-550 HBW) these improvements include:

Related Research Articles

<span class="mw-page-title-main">Heat treating</span> Process of heating something to alter it

Heat treating is a group of industrial, thermal and metalworking processes used to alter the physical, and sometimes chemical, properties of a material. The most common application is metallurgical. Heat treatments are also used in the manufacture of many other materials, such as glass. Heat treatment involves the use of heating or chilling, normally to extreme temperatures, to achieve the desired result such as hardening or softening of a material. Heat treatment techniques include annealing, case hardening, precipitation strengthening, tempering, carburizing, normalizing and quenching. Although the term heat treatment applies only to processes where the heating and cooling are done for the specific purpose of altering properties intentionally, heating and cooling often occur incidentally during other manufacturing processes such as hot forming or welding.

<span class="mw-page-title-main">Martensite</span> Type of steel crystalline structure

Martensite is a very hard form of steel crystalline structure. It is named after German metallurgist Adolf Martens. By analogy the term can also refer to any crystal structure that is formed by diffusionless transformation.

<span class="mw-page-title-main">Austenite</span> Metallic, non-magnetic allotrope of iron or a solid solution of iron, with an alloying element

Austenite, also known as gamma-phase iron (γ-Fe), is a metallic, non-magnetic allotrope of iron or a solid solution of iron with an alloying element. In plain-carbon steel, austenite exists above the critical eutectoid temperature of 1000 K (727 °C); other alloys of steel have different eutectoid temperatures. The austenite allotrope is named after Sir William Chandler Roberts-Austen (1843–1902). It exists at room temperature in some stainless steels due to the presence of nickel stabilizing the austenite at lower temperatures.

<span class="mw-page-title-main">Bainite</span> Plate-like microstructure in steels

Bainite is a plate-like microstructure that forms in steels at temperatures of 125–550 °C. First described by E. S. Davenport and Edgar Bain, it is one of the products that may form when austenite is cooled past a temperature where it is no longer thermodynamically stable with respect to ferrite, cementite, or ferrite and cementite. Davenport and Bain originally described the microstructure as being similar in appearance to tempered martensite.

<span class="mw-page-title-main">Martensitic stainless steel</span> One of the 5 crystalline structures of stainless steel

Martensitic stainless steel is a type of stainless steel alloy that has a martensite crystal structure. It can be hardened and tempered through aging and heat treatment. The other main types of stainless steel are austenitic, ferritic, duplex, and precipitation hardened.

<span class="mw-page-title-main">Carbon steel</span> Steel in which the main interstitial alloying constituent is carbon

Carbon steel is a steel with carbon content from about 0.05 up to 2.1 percent by weight. The definition of carbon steel from the American Iron and Steel Institute (AISI) states:

<span class="mw-page-title-main">Quenching</span> Rapid cooling of a workpiece to obtain certain material properties

In materials science, quenching is the rapid cooling of a workpiece in water, gas, oil, polymer, air, or other fluids to obtain certain material properties. A type of heat treating, quenching prevents undesired low-temperature processes, such as phase transformations, from occurring. It does this by reducing the window of time during which these undesired reactions are both thermodynamically favorable and kinetically accessible; for instance, quenching can reduce the crystal grain size of both metallic and plastic materials, increasing their hardness.

<span class="mw-page-title-main">Carburizing</span> Heat treatment process in which a metal or alloy is infused with carbon to increase hardness

Carburizing, or carburising, is a heat treatment process in which iron or steel absorbs carbon while the metal is heated in the presence of a carbon-bearing material, such as charcoal or carbon monoxide. The intent is to make the metal harder and more wear resistant. Depending on the amount of time and temperature, the affected area can vary in carbon content. Longer carburizing times and higher temperatures typically increase the depth of carbon diffusion. When the iron or steel is cooled rapidly by quenching, the higher carbon content on the outer surface becomes hard due to the transformation from austenite to martensite, while the core remains soft and tough as a ferritic and/or pearlite microstructure.

<span class="mw-page-title-main">Ductile iron</span> Type of cast iron

Ductile iron, also known as ductile cast iron, nodular cast iron, spheroidal graphite iron, spheroidal graphite cast iron and SG iron, is a type of graphite-rich cast iron discovered in 1943 by Keith Millis. While most varieties of cast iron are weak in tension and brittle, ductile iron has much more impact and fatigue resistance, due to its nodular graphite inclusions.

<span class="mw-page-title-main">Maraging steel</span> Steel known for strength and toughness

Maraging steels are steels that are known for possessing superior strength and toughness without losing ductility. Aging refers to the extended heat-treatment process. These steels are a special class of very-low-carbon ultra-high-strength steels that derive their strength not from carbon, but from precipitation of intermetallic compounds. The principal alloying element is 15 to 25 wt% nickel. Secondary alloying elements, which include cobalt, molybdenum and titanium, are added to produce intermetallic precipitates. Original development was carried out on 20 and 25 wt% Ni steels to which small additions of aluminium, titanium, and niobium were made; a rise in the price of cobalt in the late 1970s led to the development of cobalt-free maraging steels.

<span class="mw-page-title-main">Tempering (metallurgy)</span> Process of heat treating used to increase the toughness of iron-based alloys

Tempering is a process of heat treating, which is used to increase the toughness of iron-based alloys. Tempering is usually performed after hardening, to reduce some of the excess hardness, and is done by heating the metal to some temperature below the critical point for a certain period of time, then allowing it to cool in still air. The exact temperature determines the amount of hardness removed, and depends on both the specific composition of the alloy and on the desired properties in the finished product. For instance, very hard tools are often tempered at low temperatures, while springs are tempered at much higher temperatures.

<span class="mw-page-title-main">Hardenability</span> Depth to which a metal is hardened after being submitted to a thermal treatment

Hardenability is the depth to which a steel is hardened after putting it through a heat treatment process. It should not be confused with hardness, which is a measure of a sample's resistance to indentation or scratching. It is an important property for welding, since it is inversely proportional to weldability, that is, the ease of welding a material.

Cryogenic hardening is a cryogenic treatment process where the material is cooled to approximately −185 °C (−301 °F), usually using liquid nitrogen. It can have a profound effect on the mechanical properties of certain steels, provided their composition and prior heat treatment are such that they retain some austenite at room temperature. It is designed to increase the amount of martensite in the steel's crystal structure, increasing its strength and hardness, sometimes at the cost of toughness. Presently this treatment is being used on tool steels, high-carbon, high-chromium steels and in some cases to cemented carbide to obtain excellent wear resistance. Recent research shows that there is precipitation of fine carbides in the matrix during this treatment which imparts very high wear resistance to the steels.

Hardening is a metallurgical metalworking process used to increase the hardness of a metal. The hardness of a metal is directly proportional to the uniaxial yield stress at the location of the imposed strain. A harder metal will have a higher resistance to plastic deformation than a less hard metal.

In metallurgy and materials science, annealing is a heat treatment that alters the physical and sometimes chemical properties of a material to increase its ductility and reduce its hardness, making it more workable. It involves heating a material above its recrystallization temperature, maintaining a suitable temperature for an appropriate amount of time and then cooling.

<span class="mw-page-title-main">Ledeburite</span>

In iron and steel metallurgy, ledeburite is a mixture of 4.3% carbon in iron and is a eutectic mixture of austenite and cementite. Ledeburite is not a type of steel as the carbon level is too high although it may occur as a separate constituent in some high carbon steels. It is mostly found with cementite or pearlite in a range of cast irons.

<span class="mw-page-title-main">Isothermal transformation diagram</span>

Isothermal transformation diagrams are plots of temperature versus time. They are generated from percentage transformation-vs time measurements, and are useful for understanding the transformations of an alloy steel at elevated temperatures.

Martempering is also known as stepped quenching or interrupted quenching. In this process, steel is heated above the upper critical point and then quenched in a hot-oil, molten-salt, or molten-lead bath kept at a temperature of 150-300 °C. The workpiece is held at this temperature above martensite start (Ms) point until the temperature becomes uniform throughout the cross-section of the workpiece. After that, it is cooled in air or oil to room temperature. The steel is then tempered. In this process, austenite is transformed to martensite by step quenching, at a rate fast enough to avoid the formation of ferrite, pearlite, or bainite.

Thermomechanical processing is a metallurgical process that combines mechanical or plastic deformation process like compression or forging, rolling, etc. with thermal processes like heat-treatment, water quenching, heating and cooling at various rates into a single process.

<span class="mw-page-title-main">Austempered Ductile Iron</span>

Austempered Ductile Iron (ADI) is a form of ductile iron that enjoys high strength and ductility as a result of its microstructure controlled through heat treatment. While conventional ductile iron was discovered in 1943 and the austempering process had been around since the 1930s, the combination of the two technologies was not commercialized until the 1970s.

References

  1. 1 2 Bhadeshia, H. K. D. H., "Bainite in Steels: Transformations, Microstructure, and properties" second edition, IOM Communications, London, England, 2001
  2. Bain, Edgar C., "Functions of the Alloying Elements in Steel" American Society for Metals, Cleveland, Ohio, 1939
  3. Irvine, K.J. and Pickering, F.B. JISI 188, 1958.
  4. 1 2 3 4 "Home". Applied Process. Retrieved 2022-04-24.
  5. 1 2 "Heat Treater's Guide: Practices and procedures for Irons and Steels" ASM International, Materials Park, Ohio, Second Edition,1995