Parking brake

Last updated
Parking brake lever from a Saab 9-5 Handbrake lever.JPG
Parking brake lever from a Saab 9-5

In road vehicles, the parking brake, also known as a handbrake or emergency brake (e-brake), is a mechanism used to keep the vehicle securely motionless when parked. Parking brakes often consist of a pulling mechanism attached to a cable which is connected to two wheel brakes. In most vehicles, the parking brake operates only on the rear wheels, [1] which have reduced traction while braking. The mechanism may be a hand-operated lever, a straight pull handle located near the steering column, or a foot-operated pedal located with the other pedals.

Contents

Overview

In manual transmission vehicles, the parking brake is engaged to help keep the vehicle stationary while parked, especially if parked on an incline. [2] [3] While automatic transmission vehicles have a "Park" gear that immobilizes the transmission, it is still recommended to use the parking brake, as the parking pawl in the gearbox could fail due to stress or another vehicle striking the car, causing the car to roll. [4] [5]

When parking on an uphill gradient, it is recommended that the front wheels face away from the curb. This would prevent the car from rolling into the roadway by using the curb to block the front passenger tire in the event of a parking brake failure. [6] Similarly, on a downhill gradient, the front wheels should face the curb for the same reason, and the wheels should face to the side of the road on which vehicles are driven on an uncurbed road regardless of orientation. In a manual transmission, leaving the car in first gear (or in reverse if pointing downhill) is also advised, as the engine will prevent the car from rolling if the parking brake fails. [7] [8] [9]

The parking brake in most vehicles is still completely mechanical. Traditionally engaged by pulling a lever, the cables manually engage part of the car's braking system, usually the rear disk or drum brakes. [10] The mechanical nature allows the driver to apply the brake even if the main hydraulic brake system fails. [3]

Pictograph symbols and/or lights may be used to indicate the location of a parking brake, its application or release. [11]

Other uses

In manual and automatic transmission vehicles, the parking brake can also be used for various driving situations which require the vehicle to be momentarily stopped. For example, the brake can be engaged when moving off an uphill slope, as this allows the driver to hold the accelerator and clutch pedals steady without the vehicle rolling backwards. [12] [13] Other common situations is when the vehicle is stopped at a traffic light, a pedestrian crossing, or simply waiting to turn in front of oncoming traffic. [14] The parking brake would ensure the car is secure, should another vehicle come into physical contact from behind, causing the car to jolt forward. [15] It is not recommended to use the parking brake when the vehicle is in-motion, unless there is a problem with the main brakes, as this can lock the back wheels and cause a skid. [16] This is known as a handbrake turn, which is often performed in street racing and rallying to initiate rear wheel drift.

In the event of hydraulic brake failure, the parking brake can be used to slow a vehicle. In such cases, the lever should be slowly engaged to prevent locking up the wheels. [17]

Parking brake variations

ISO symbol used to indicate that the parking brake is applied B02 Parking brake indication.svg
ISO symbol used to indicate that the parking brake is applied

The position of the parking brake differs between vehicle models and manufacturers. However, a universal feature is either one or two of the warning lights which appear on the dashboard when the parking brake is engaged. [18] [19]

Brake warning light B01 Brake failure.svg
Brake warning light

Center or stick lever

The most common placement of the parking brake is in the center console of the vehicle, in between the driver and front passenger seats.[ citation needed ] Operating the brake is performed by pulling the lever up (which is connected to a ratchet) until there is tension. To disengage the brake, the button is held while simultaneously pulling the lever up to disengage the ratchet and then pushed all the way down with the button still held. In older vehicle models, a stick lever may be used instead which is located under the instrument panel.

Pedal or pull handle

Some vehicles have the parking brake operated by a small foot pedal, located by the other pedals. Depressing the foot pedal would engage the brake and pressing it again will release it. A pull handle variation also exists; by pulling or releasing the handle, this engages and releases the parking brake, respectively. Many vehicles have a combination of the two; a pedal to engage the brake and a handle to release it.

Electric park brake on a Volkswagen Touran Elektrische Feststellbremse VW Touran.jpg
Electric park brake on a Volkswagen Touran

Electronic

A recent development is the electronic parking brake, also known as an electric park brake. Introduced to the mainstream market in 2001, it was first used in the 2001 BMW 7 Series (E65). [20] Two variations are available: In the more-traditional "cable-pulling" type, an electric motor simply pulls the parking brake cable on the push or pull of a button rather than a mechanical lever or pedal in the cabin. A more complex unit [21] (first seen on the 2003 Audi A8) uses a computer-controlled motor attached to each of the two rear brake calipers referred to as the Motor on Caliper (MoC) system.

Many car manufacturers such as Jaguar, Land Rover, BMW, Renault, Subaru and Volkswagen sell models whereby the parking brake automatically engages when the vehicle is stopped and is released when the gas pedal is pressed, [22] eliminating the need for the driver to operate a button. [23] An extension of this system, known as hill-hold or hill-assist, prevents the vehicle from rolling back when moving-off on an uphill gradient. [24]

Types of brakes

In vehicles with rear disc brakes, the parking brake either actuates the disc calipers (with much less force) or a small drum brake housed within the hub assembly (the inner circumference of the disc is often used instead of a separate drum). This secondary drum parking brake is often referred to as a banksia brake. It is usually used in conjunction with rear disc brakes employing multi-piston calipers, as mechanically actuating these calipers is more difficult than single piston calipers.

Another less common setup for rear discs is the use of a separate, smaller, cable actuated caliper (such as the Wilwood MC4), which is used exclusively for the parking brake. This is sometimes used as an alternative to a separate drum parking brake when multi-piston main calipers are used.

Hudson automobiles used an unusual hybrid hydraulic-mechanical dual-brake system which operated the rear brakes through the otherwise conventional mechanical parking brake system when a failure of the hydraulic system allowed the pedal to travel beyond its normal limit. [25]

A number of production vehicles, light and medium duty trucks, and motor homes have been made with a separate drum brake on the driveline; called a transmission brake. This has an advantage of being completely independent of other braking systems. This is effective when there are multiple driving axles: all driven wheels are braked at once.

A line lock is a temporary parking brake that makes use of the vehicles standard hydraulic brakes. They are often used for off road conditions or when stopping on steep grades is required. By trapping hydraulic pressure in the brake lines, all four wheels can be locked.

Large vehicles

Large vehicles are usually fitted with power operated or power assisted parking brakes. Power assisted parking brakes are usually found on large vans as well as some older heavy vehicles. These operate in the same way as a conventional parking brakes, but pulling the lever operates a valve that allows air or hydraulic pressure or vacuum into a cylinder which applies force to the brake shoes and makes applying the parking brake easier. When releasing the parking brake, the same mechanism also provides assistance to the driver in disengaging the ratchet. Particularly on commercial vehicles with air operated brakes, this has the added benefit of making it much harder or even impossible to release the parking brake when insufficient air pressure is available to operate the brakes. A reservoir or accumulator is usually provided so a limited amount of power assistance is available with the engine off.

Power operated parking brakes are fitted to heavy commercial vehicles with air brakes, such as trucks and buses. These are usually spring applied, with air pressure being used to hold the brake off and powerful springs holding the brakes on. In most cases, a small lever in the cab is connected to a valve which can admit air to the parking brake cylinders to release the parking brake, or release the air to apply the brake. On some modern vehicles the valve is operated electrically from a lever or button in the cab. The system is relatively safe since if air pressure is lost the springs will apply the brakes. Also, the system prevents the parking brake being released if there is insufficient air pressure to apply the foot brake. A disadvantage to this system is that if a vehicle requires towing and cannot provide its own air supply, an external supply must be provided to allow the parking brake to be released, or the brake shoes must be manually wound off against the springs.

Railroad hand brakes

Virtually all railroad rolling stock is equipped with manually operated mechanical hand brake devices that set and release the brakes. Most of these involve a chain linked to the brake rigging, most often at the brake cylinder, that when tightened pull the piston out against the releasing springs, thus applying the brakes on the car (if there is only one brake cylinder per car) or bogie (if there is more than one cylinder per car). Newer locomotives have electric systems that simply place an electric motor in place of the chain winding mechanism. This brake acts independently of the action of the automatic air brakes, which function collectively when coupled in a train and are under the control of the locomotive driver / engineer.

Manual hand brakes serve to keep a piece of rolling stock stationary after it has been spotted in a rail yard or at a customer for unloading or loading. They are also used to secure a parked train from inadvertent movement, especially while unmanned.

Before the development of locomotive-actuated train braking systems in the late 19th century, American railroads employed brakemen to move about the tops of cars, setting hand brakes on the engineer's signal in an effort to stop the train in a timely manner. This process was imprecise and extremely dangerous. Many brakemen lost life and limb as a result of falling from a moving train, icy and wet conditions often adding to the hazards involved in negotiating the top of a swaying boxcar. [26] In the U.S., an 1893 federal law, the Railroad Safety Appliance Act, required automatic brakes on all railroads, effective in 1900. [27]

See also

Notes

  1. Military.com (November 2017). "Auto Repair: The Parking Brake". Military.com. Retrieved 2019-05-11.
  2. "5 Important Tips for Parking a Manual Transmission Car". Oards.com. 2018-01-09. Retrieved 2019-05-12.
  3. 1 2 "Why You Should Set Your Parking Brake". DrivrZone.com. 2018-06-27. Retrieved 2019-05-12.
  4. "Things You Should Never Do With an Automatic Transmission". A&P Auto Parts. 2017-05-15. Archived from the original on 2017-05-16. Retrieved 2019-05-12.
  5. "When to Use Your Parking Brake | Firestone Complete Auto Care". Completely Firestone. 2017-06-12. Archived from the original on 2017-09-27. Retrieved 2019-05-12.
  6. "7 Trusted Steps to Park on a Hill Without Serious Accidents". Driving-Tests.org. Retrieved 2019-05-12.
  7. "Controlling your vehicle | DVSA - Safe Driving for Life". www.safedrivingforlife.info. Retrieved 2019-05-12.
  8. "Do you leave your car in gear?". Which? Conversation. 2016-03-13. Retrieved 2019-05-12.
  9. "How to park correctly on a hill" . Retrieved 2019-05-12.
  10. "How to Use a Parking Brake | Wagner Brake". Wagner Brake | Brake Pads, Brake Rotors & Headlights. Retrieved 2019-05-12.
  11. Parking brake indicator
  12. "How to do a hill start: uphill and downhill". Driving Tests Resources. 2017-06-19. Retrieved 2019-05-12.
  13. Tips, Driving Test. "Hill Starts – Driving Test Tips" . Retrieved 2019-05-12.
  14. Tips, Driving Test. "When To Use Handbrake – Driving Test Tips" . Retrieved 2019-05-12.
  15. "Handbrake – Long stay or Short stay?". www.iam-bristol.org.uk. Retrieved 2019-05-12.
  16. "Learning to drive - the Handbrake". www.drivinghelp.com. Retrieved 2019-05-12.
  17. "Car Myths Debunked – When to Use Your Emergency Brake". NAPA Know How Blog. 2015-12-07. Retrieved 2019-05-11.
  18. "Understanding What Dashboard Warnings Mean - Direct Line". www.directline.com. Retrieved 2019-05-12.
  19. "Brake Warning Light". www.aa1car.com. Retrieved 2019-05-12.
  20. "PH Origins: Electronic parking brakes | PistonHeads". www.pistonheads.com. Retrieved 2019-05-11.
  21. "trw.com". Archived from the original on 2016-11-20. Retrieved 2013-12-18.
  22. "What is an electronic parking brake or electronic handbrake?". www.carwow.co.uk. Retrieved 2019-05-11.
  23. "What is an electronic parking brake? | Parkers". www.parkers.co.uk. Retrieved 2019-05-11.
  24. "What would happen if you engaged electronic parking brake while driving?". Technology Org. 2018-10-26. Retrieved 2019-05-11.
  25. "Hudson Motor Car Company - Hudson Car Club - Hudson, Essex, Terraplane Cars". Hudsonclub.org. 2009-03-09. Archived from the original on 2011-04-23. Retrieved 2011-04-24.
  26. McDonald, Charles (1993). The Federal Railroad Safety Program (PDF). Washington, DC: U.S. Federal Railroad Administration. pp. 2–5. Archived from the original (PDF) on 2009-07-31.
  27. United States. Act of Mar. 2, 1893, 27  Stat.   531, recodified, as amended, 49 U.S.C.   § 20302.

Related Research Articles

<span class="mw-page-title-main">Clutch</span> Mechanical device that connects and disconnects two rotating shafts or other moving parts

A clutch is a mechanical device that allows the output shaft to be disconnected from the rotating input shaft. The clutch's input shaft is typically attached to a motor, while the clutch's output shaft is connected to the mechanism that does the work.

<span class="mw-page-title-main">Anti-lock braking system</span> Safety anti-skid braking system used on aircraft and land vehicles

An anti-lock braking system (ABS) is a safety anti-skid braking system used on aircraft and on land vehicles, such as cars, motorcycles, trucks, and buses. ABS operates by preventing the wheels from locking up during braking, thereby maintaining tractive contact with the road surface and allowing the driver to maintain more control over the vehicle.

<span class="mw-page-title-main">Drum brake</span> Type of vehicle brake

A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward against a rotating bowl-shaped part called a brake drum.

<span class="mw-page-title-main">Bicycle brake</span> Braking device for bicycles

A bicycle brake reduces the speed of a bicycle or prevents it from moving. The three main types are: rim brakes, disc brakes, and drum brakes.

Left-foot braking is the technique of using the left foot to operate the brake pedal in an automobile, leaving the right foot dedicated to the throttle pedal. It contrasts with the practice of using the left foot to operate the clutch pedal, leaving the right foot to share the duties of controlling both brake and gas pedals.

<span class="mw-page-title-main">Handbrake turn</span> Driving technique

The handbrake turn is a driving technique used to deliberately slide a car sideways, either for the purpose of quickly negotiating a very tight bend, or for turning around well within the vehicle's own turning diameter.

<span class="mw-page-title-main">Automatic transmission</span> Type of motor vehicle transmission that automatically changes gear ratio as the vehicle moves

An automatic transmission is a multi-speed transmission used in motor vehicles that does not require any input from the driver to change forward gears under normal driving conditions. Vehicles with internal combustion engines, unlike electric vehicles, require the engine to operate in a narrow range of rates of rotation, requiring a gearbox, operated manually or automatically, to drive the wheels over a wide range of speeds.

<span class="mw-page-title-main">Manual transmission</span> Motor vehicle manual gearbox; stick shift

A manual transmission (MT), also known as manual gearbox, standard transmission, or stick shift, is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch.

<span class="mw-page-title-main">Drive by wire</span> Automotive technology

Drive by wire or DbW technology in the automotive industry is the use of electronic or electro-mechanical systems in place of mechanical linkages that control driving functions. The concept is similar to fly-by-wire in the aviation industry. Drive-by-wire may refer to just the propulsion of the vehicle through electronic throttle control, or it may refer to electronic control over propulsion as well as steering and braking, which separately are known as steer by wire and brake by wire, along with electronic control over other vehicle driving functions.

<span class="mw-page-title-main">Preselector gearbox</span> Type of manual transmission

A preselector gearbox is a type of manual transmission mostly used on passenger cars and racing cars in the 1930s, in buses from 1940-1960 and in armoured vehicles from the 1930s to the 1970s. The defining characteristic of a preselector gearbox is that the gear shift lever allowed the driver to "pre-select" the next gear, usually with the transmission remaining in the current gear until the driver pressed the "gear change pedal" at the desired time.

<span class="mw-page-title-main">Hydraulic brake</span> Arrangement of braking mechanism

A hydraulic brake is an arrangement of braking mechanism which uses brake fluid, typically containing glycol ethers or diethylene glycol, to transfer pressure from the controlling mechanism to the braking mechanism.

Hill-holder is a motor vehicle device that holds the brake until the clutch is at the friction point, making it easier for a stationary vehicle to start uphill. By holding the brake in position while the vehicle is put into gear, it prevents rollback. It was invented by Wagner Electric and manufactured by Bendix Brake Company in South Bend, Indiana.

<span class="mw-page-title-main">Ford Model AA</span> Heavy-duty version of the Ford Model A

Ford Model AA is a truck from Ford. As the Model T and TT became obsolete and needed to be replaced, Henry Ford began initial designs on the Model A and Model AA in 1926. Basic chassis layout was done rapidly and mechanical development was moved forward quickly. Body design and style was developed and then outsourced to various body manufacturers, including Briggs and Murray. The designs of the Model A shared parts and materials with the Model AA Ford, notably the body, engine and interior. The AA usually received plainer interiors than their car counterparts. The Model AA followed similar design changes to the Model A during the AA's four years in production, often delayed anywhere from three to nine months. The mechanical changes and upgrades were done during production of the vehicles. Body changes that occurred between 1929 and 1930 were also integrated into AA production, but leftover parts were used longer in the heavy commercial trucks.

<span class="mw-page-title-main">Gear stick</span> Lever used for shifting gears manually

A gear stick, gear lever, gearshift or shifter, more formally known as a transmission lever, is a metal lever attached to the transmission of an automobile. The term gear stick mostly refers to the shift lever of a manual transmission, while in an automatic transmission, a similar lever is known as a gear selector. A gear stick will normally be used to change gear whilst depressing the clutch pedal with the left foot to disengage the engine from the drivetrain and wheels. Automatic transmission vehicles, including hydraulic automatic transmissions, automated manual and older semi-automatic transmissions, like VW Autostick, and those with continuously variable transmissions, do not require a physical clutch pedal.

<span class="mw-page-title-main">Air brake (road vehicle)</span> Type of friction brake for vehicles

An air brake or, more formally, a compressed-air-brake system, is a type of friction brake for vehicles in which compressed air pressing on a piston is used to both release the parking/emergency brakes in order to move the vehicle, and also to apply pressure to the brake pads or brake shoes to slow and stop the vehicle. Air brakes are used in large heavy vehicles, particularly those having multiple trailers which must be linked into the brake system, such as trucks, buses, trailers, and semi-trailers, in addition to their use in railroad trains. George Westinghouse first developed air brakes for use in railway service. He patented a safer air brake on March 5, 1872. Westinghouse made numerous alterations to improve his air pressured brake invention, which led to various forms of the automatic brake. In the early 20th century, after its advantages were proven in railway use, it was adopted by manufacturers of trucks and heavy road vehicles.

<span class="mw-page-title-main">Brake-by-wire</span> Automotive technology

Brake-by-wire technology in the automotive industry is the ability to control brakes through electronic means, without a mechanical connection that transfers force to the physical braking system from a driver input apparatus such as a pedal or lever.

<span class="mw-page-title-main">Line lock</span> Vehicle braking technology

A line lock is a device that allows the front brakes to lock independently of the rear brakes via a switch. The device is an electric solenoid that controls a valve which allows the brakes to be controlled individually. This allows the front brakes to be locked and the rear brakes to be open, and allows the driver to spin the rear wheels without wasting the rear brakes. This method is referred to as line lock and is popular among enthusiasts who like to do burnouts.

Power brakes consist of a system of hydraulics used to slow down or stop a motor vehicle. It uses a combination of mechanical components and vacuum assistance to multiply the pressure applied to the brake pedal by the driver into enough force to actuate the brakes and stop the vehicle. By contrast, manual brakes rely solely on the pressure the driver applies to the brake pedal.

<span class="mw-page-title-main">Transmission brake</span>

A transmission brake or driveline parking brake is an inboard vehicle brake that is applied to the drivetrain rather than to the wheels.

<span class="mw-page-title-main">Car controls</span> Car parts used to control the vehicle

Car controls are the components in automobiles and other powered road vehicles, such as trucks and buses, used for driving and parking.