Hard water

Not to be confused with Heavy water or Ice.

A bathtub faucet with built-up calcification from hard water in Southern Arizona

Hard water is water that has a high mineral content (in contrast with "soft water"). Hard water is formed when water percolates through deposits of limestone, chalk or gypsum, ^[1] which are largely made up of calcium and magnesium carbonates, bicarbonates and sulfates.

Drinking hard water may have moderate health benefits. It can pose critical problems in industrial settings, where water hardness is monitored to avoid costly breakdowns in boilers, cooling towers, and other equipment that handles water. In domestic settings, hard water is often indicated by a lack of foam formation when soap is agitated in water, and by the formation of limescale in kettles and water heaters. ^[2] Wherever water hardness is a concern, water softening is commonly used to reduce hard water's adverse effects.

Origins

Natural rainwater, snow and other forms of precipitation typically have low concentrations of divalent cations such as calcium and magnesium. They may have small concentrations of ions such as sodium, chloride and sulfate derived from wind action over the sea. Where precipitation falls in drainage basins formed of hard, impervious and calcium-poor rocks, only very low concentrations of divalent cations are found and the water is termed soft water. ^[3] Examples include Snowdonia in Wales and the Western Highlands in Scotland.

Areas with complex geology can produce varying degrees of hardness of water over short distances. ^{[4] [5]}

Types

Permanent hardness

The permanent hardness of water is determined by the water's concentration of cations with charges greater than or equal to 2+. Usually, the cations have a charge of 2+, i.e., they are divalent. Common cations found in hard water include Ca²⁺ and Mg²⁺, which frequently enter water supplies by leaching from minerals within aquifers. Common calcium-containing minerals are calcite and gypsum. A common magnesium mineral is dolomite (which also contains calcium). Rainwater and distilled water are soft, because they contain few of these ions. ^[3]

The following equilibrium reaction describes the dissolving and formation of calcium carbonate and calcium bicarbonate (on the right):

CaCO₃ (s) + CO₂ (aq) + H₂O (l) ⇌ Ca²⁺ (aq) + 2 HCO⁻
₃ (aq)

The reaction can go in either direction. Rain containing dissolved carbon dioxide can react with calcium carbonate and carry calcium ions away with it. The calcium carbonate may be re-deposited as calcite as the carbon dioxide is lost to the atmosphere, sometimes forming stalactites and stalagmites.

Calcium and magnesium ions can sometimes be removed by water softeners. ^[6]

Permanent hardness (mineral content) is generally difficult to remove by boiling. ^[7] If this occurs, it is usually caused by the presence of calcium sulfate/calcium chloride and/or magnesium sulfate/magnesium chloride in the water, which do not precipitate out as the temperature increases. Ions causing the permanent hardness of water can be removed using a water softener, or ion-exchange column.

Temporary hardness

See also: Carbonate hardness

Temporary hardness is caused by the presence of dissolved bicarbonate minerals (calcium bicarbonate and magnesium bicarbonate). When dissolved, these types of minerals yield calcium and magnesium cations (Ca²⁺, Mg²⁺) and carbonate and bicarbonate anions (CO²⁻
₃ and HCO⁻
₃). The presence of the metal cations makes the water hard. However, unlike the permanent hardness caused by sulfate and chloride compounds, this "temporary" hardness can be reduced either by boiling the water or by the addition of lime (calcium hydroxide) through the process of lime softening. ^[8] Boiling promotes the formation of carbonate from the bicarbonate and precipitates calcium carbonate out of solution, leaving water that is softer upon cooling.

Effects

With hard water, soap solutions form a white precipitate (soap scum) instead of producing lather, because the 2+ ions destroy the surfactant properties of the soap by forming a solid precipitate (the soap scum). A major component of such scum is calcium stearate, which arises from sodium stearate, the main component of soap:

2 C₁₇H₃₅COO⁻ (aq) + Ca²⁺ (aq) → (C₁₇H₃₅COO)₂Ca (s)

Hardness can thus be defined as the soap-consuming capacity of a water sample, or the capacity of precipitation of soap as a characteristic property of water that prevents the lathering of soap. Synthetic detergents do not form such scums.

A portion of the ancient Roman Eifel Aqueduct in Germany. After being in service for about 180 years, the aqueduct had mineral deposits of up to 20 cm (8 in) thick along the walls.

Because soft water has few calcium ions, there is no inhibition of the lathering action of soaps and no soap scum is formed in normal washing. Similarly, soft water produces no calcium deposits in water heating systems.

Hard water also forms deposits that clog plumbing. These deposits, called "scale", are composed mainly of calcium carbonate (CaCO₃), magnesium hydroxide (Mg(OH)₂), and calcium sulfate (CaSO₄). ^[3] Calcium and magnesium carbonates tend to be deposited as off-white solids on the inside surfaces of pipes and heat exchangers. This precipitation (formation of an insoluble solid) is principally caused by thermal decomposition of bicarbonate ions but also happens in cases where the carbonate ion is at saturation concentration. ^[9] The resulting build-up of scale restricts the flow of water in pipes. In boilers, the deposits impair the flow of heat into water, reducing the heating efficiency and allowing the metal boiler components to overheat. In a pressurized system, this overheating can lead to the failure of the boiler. ^[10] The damage caused by calcium carbonate deposits varies according to the crystalline form, for example, calcite or aragonite. ^[11]

The presence of ions in an electrolyte, in this case, hard water, can also lead to galvanic corrosion, in which one metal will preferentially corrode when in contact with another type of metal when both are in contact with an electrolyte. The softening of hard water by ion exchange does not increase its corrosivity per se. Similarly, where lead plumbing is in use, softened water does not substantially increase plumbo-solvency. ^[12]

In swimming pools, hard water is manifested by a turbid, or cloudy (milky), appearance to the water. Calcium and magnesium hydroxides are both soluble in water. The solubility of the hydroxides of the alkaline-earth metals to which calcium and magnesium belong (group 2 of the periodic table) increases moving down the column. Aqueous solutions of these metal hydroxides absorb carbon dioxide from the air, forming insoluble carbonates, and giving rise to turbidity. This often results from the pH being excessively high (pH > 7.6). Hence, a common solution to the problem is, while maintaining the chlorine concentration at the proper level, to lower the pH by the addition of hydrochloric acid, the optimum value is in the range of 7.2 to 7.6.

Softening

Main article: Water softening

In some cases it is desirable to soften hard water. Most detergents contain ingredients that counteract the effects of hard water on the surfactants. For this reason, water softening is often unnecessary. Where softening is practised, it is often recommended to soften only the water sent to domestic hot water systems to prevent or delay inefficiencies and damage due to scale formation in water heaters. A common method for water softening involves the use of ion-exchange resins, which replace ions like Ca²⁺ by twice the number of mono cations such as sodium or potassium ions.

Washing soda (sodium carbonate, Na₂CO₃) is easily obtained and has long been used as a water softener for domestic laundry, in conjunction with the usual soap or detergent.

Water that has been treated by a water softening may be termed softened water. In these cases, the water may also contain elevated levels of sodium or potassium and bicarbonate or chloride ions.

Health considerations

The World Health Organization says that "there does not appear to be any convincing evidence that water hardness causes adverse health effects in humans". ^[2] In fact, the United States National Research Council has found that hard water serves as a dietary supplement for calcium and magnesium. ^[13]

Some studies have shown a weak inverse relationship between water hardness and cardiovascular disease in men, up to a level of 170 mg calcium carbonate per litre of water. The World Health Organization has reviewed the evidence and concluded the data was inadequate to recommend a level of hardness. ^[2]

Recommendations have been made for the minimum and maximum levels of calcium (40–80  ppm) and magnesium (20–30 ppm) in drinking water, and a total hardness expressed as the sum of the calcium and magnesium concentrations of 2–4 mmol/L. ^[14]

Other studies have shown weak correlations between cardiovascular health and water hardness. ^{[15] [16] [17]}

The prevalence of atopic dermatitis (eczema) in children may be increased by hard drinking water. ^{[18] [19]} Living in areas with hard water may also play a part in the development of AD in early life. However, when AD is already established, using water softeners at home does not reduce the severity of the symptoms. ^[19]

Measurement

Hardness can be quantified by instrumental analysis. The total water hardness is the sum of the molar concentrations of Ca²⁺ and Mg²⁺, in mol/L or mmol/L units. Although water hardness usually measures only the total concentrations of calcium and magnesium (the two most prevalent divalent metal ions), iron, aluminium, and manganese are also present at elevated levels in some locations. The presence of iron characteristically confers a brownish (rust-like) colour to the calcification, instead of white (the colour of most of the other compounds).

Water hardness is often not expressed as a molar concentration, but rather in various units, such as degrees of general hardness (dGH), German degrees (°dH), parts per million (ppm, mg/L, or American degrees), grains per gallon (gpg), English degrees (°e, e, or °Clark), or French degrees (°fH, °f or °HF; lowercase f is used to prevent confusion with degrees Fahrenheit). The table below shows conversion factors between the various units.

Hardness unit conversion.

	1 mmol/L	1 ppm, mg/L	1 dGH, °dH	1 gpg	1 °e, °Clark	1 °fH
mmol/L	1	0.009991	0.1783	0.171	0.1424	0.09991
ppm, mg/L	100.1	1	17.85	17.12	14.25	10
dGH, °dH	5.608	0.05603	1	0.9591	0.7986	0.5603
gpg	5.847	0.05842	1.043	1	0.8327	0.5842
°e, °Clark	7.022	0.07016	1.252	1.201	1	0.7016
°fH	10.01	0.1	1.785	1.712	1.425	1

The various alternative units represent an equivalent mass of calcium oxide (CaO) or calcium carbonate (CaCO₃) that, when dissolved in a unit volume of pure water, would result in the same total molar concentration of Mg²⁺ and Ca²⁺. The different conversion factors arise from the fact that equivalent masses of calcium oxide and calcium carbonates differ and that different mass and volume units are used. The units are as follows:

• Parts per million (ppm) is usually defined as 1 mg/L CaCO₃ (the definition used below). ^[20] It is equivalent to mg/L without chemical compound specified, and to American degree.
• Grain per gallon (gpg) is defined as 1 grain (64.8 mg) of calcium carbonate per U.S. gallon (3.79 litres), or 17.118 ppm.
• 1 mmol/L is equivalent to 100.09 mg/L CaCO₃ or 40.08 mg/L Ca²⁺.
• A degree of General Hardness (dGH or 'German degree' (°dH, deutsche Härte)) is defined as 10 mg/L CaO or 17.848 ppm.
• A Clark degree (°Clark) or English degree (°e or e) is defined as one grain (64.8  mg) of CaCO₃ per Imperial gallon (4.55 litres) of water, equivalent to 14.254 ppm.
• A French degree (°fH or °f) is defined as 10 mg/L CaCO₃, equivalent to 10 ppm.

Hard/soft classification

As it is the precise mixture of minerals dissolved in the water, together with water's pH and temperature, that determine the behaviour of the hardness, a single-number scale does not adequately describe hardness. However, the United States Geological Survey uses the following classification for hard and soft water: ^[5]

Classification	mg-CaCO3/L (ppm)	mmol/L	dGH/°dH	gpg
Soft	0–60	0–0.60	0–3.37	0–3.50
Moderately hard	61–120	0.61–1.20	3.38–6.74	3.56–7.01
Hard	121–180	1.21–1.80	6.75–10.11	7.06–10.51
Very hard	≥ 181	≥ 1.81	≥ 10.12	≥ 10.57

Seawater is considered to be very hard due to various dissolved salts. Typically seawater's hardness is in the area of 6,570 ppm (6.57 grams per litre). ^[21] In contrast, fresh water has a hardness in the range of 15 to 375 ppm, generally around 600 mg/L. ^[22]

Indices

Several indices are used to describe the behaviour of calcium carbonate in water, oil, or gas mixtures. ^{[23] [ better source needed ]}

Langelier saturation index (LSI)

The Langelier saturation index ^[24] (sometimes Langelier stability index) is a calculated number used to predict the calcium carbonate stability of water. ^[25] It indicates whether the water will precipitate, dissolve, or be in equilibrium with calcium carbonate. In 1936, Wilfred Langelier developed a method for predicting the pH at which water is saturated in calcium carbonate (called pH_s). ^[26] The LSI is expressed as the difference between the actual system pH and the saturation pH: ^[27]

LSI = pH (measured) − pH_s

• For LSI > 0, water is supersaturated and tends to precipitate a scale layer of CaCO₃.
• For LSI = 0, water is saturated (in equilibrium) with CaCO₃. A scale layer of CaCO₃ is neither precipitated nor dissolved.
• For LSI < 0, water is under-saturated and tends to dissolve solid CaCO₃.

If the actual pH of the water is below the calculated saturation pH, the LSI is negative and the water has a very limited scaling potential. If the actual pH exceeds pHs, the LSI is positive, and being supersaturated with CaCO₃, the water tends to form scale. At increasing positive index values, the scaling potential increases.

In practice, water with an LSI between −0.5 and +0.5 will not display enhanced mineral dissolving or scale-forming properties. Water with an LSI below −0.5 tends to exhibit noticeably increased dissolving abilities while water with an LSI above +0.5 tends to exhibit noticeably increased scale-forming properties.

The LSI is temperature-sensitive. The LSI becomes more positive as the water temperature increases. This has particular implications in situations where well water is used. The temperature of the water when it first exits the well is often significantly lower than the temperature inside the building served by the well or at the laboratory where the LSI measurement is made. This increase in temperature can cause scaling, especially in cases such as water heaters. Conversely, systems that reduce water temperature will have less scaling.

• Water analysis:
  • pH = 7.5
  • TDS = 320 mg/L
  • Calcium = 150 mg/L (or ppm) as CaCO₃
  • Alkalinity = 34 mg/L (or ppm) as CaCO₃
• LSI formula:
  • LSI = pH − pH_s
  • pH_s = (9.3 + A + B) − (C + D) where:
    • A = ⁠log₁₀[TDS] − 1/10⁠ = 0.15
    • B = −13.12 × log₁₀(°C + 273) + 34.55 = 2.09 at 25 °C and 1.09 at 82 °C
    • C = log₁₀[Ca²⁺ as CaCO₃] – 0.4 = 1.78
      • (Ca²⁺ as CaCO₃ is also called calcium hardness, and is calculated as 2.5[Ca²⁺])
    • D = log₁₀[alkalinity as CaCO₃] = 1.53

Ryznar stability index (RSI)

The Ryznar stability index (RSI) ^{[24] : 525} uses a database of scale thickness measurements in municipal water systems to predict the effect of water chemistry. ^{[25] : 72  [28]} It was developed from empirical observations of corrosion rates and film formation in steel mains.

This index is defined as: ^[29]

RSI = 2 pH_s – pH (measured)

• For 6.5 < RSI < 7 water is considered to be approximately at saturation equilibrium with calcium carbonate
• For RSI > 8 water is undersaturated and, therefore, would tend to dissolve any existing solid CaCO₃
• For RSI < 6.5 water tends to be scale form

Puckorius scaling index (PSI)

The Puckorius scaling index (PSI) uses slightly different parameters to quantify the relationship between the saturation state of the water and the amount of limescale deposited.

Other indices

Other indices include the Larson-Skold Index, ^[30] the Stiff-Davis Index, ^[31] and the Oddo-Tomson Index. ^[32]

Regional information

The hardness of local water supplies depends on the source of water. Water in streams flowing over volcanic (igneous) rocks will be soft, while water from boreholes drilled into porous rock is normally very hard.

Australia

Analysis of water hardness in major Australian cities by the Australian Water Association shows a range from very soft (Melbourne) to hard (Adelaide). Total hardness levels of calcium carbonate in ppm are:

• Canberra: 40 ^[33]
• Melbourne: 10–26 ^[34]
• Sydney: 39.4–60.1 ^[35]
• Perth: 29–226 ^[36]
• Brisbane: 100 ^[37]
• Adelaide: 134–148 ^[38]
• Hobart: 5.8–34.4 ^[39]
• Darwin: 31 ^[40]

Canada

Prairie provinces (mainly Saskatchewan and Manitoba) contain high quantities of calcium and magnesium, often as dolomite, which are readily soluble in the groundwater that contains high concentrations of trapped carbon dioxide from the last glaciation. In these parts of Canada, the total hardness in ppm of calcium carbonate equivalent frequently exceeds 200 ppm, if groundwater is the only source of potable water. The west coast, by contrast, has unusually soft water, derived mainly from mountain lakes fed by glaciers and snowmelt.

Some typical values are:

• Montreal, Quebec: 116 ppm ^[41]
• Calgary, Alberta: 165 ppm^{[ citation needed ]}
• Regina, Saskatchewan: 496 ppm ^[42]
• Saskatoon, Saskatchewan: 160–180 ppm ^[43]
• Winnipeg, Manitoba: 77 ppm ^[44]
• Toronto, Ontario: 121 ppm ^[45]
• Vancouver, British Columbia: < 3 ppm ^[46]
• Charlottetown, Prince Edward Island: 140–150 ppm ^[47]
• Waterloo Region, Ontario: 400 ppm
• Guelph, Ontario: 460 ppm ^[48]
• Saint John (West), New Brunswick: 160–200 ppm ^[49]
• Ottawa, Ontario: 30 ppm ^[50]

England and Wales

Hardness water level of major cities in England and Wales

Area	Primary source	Level [51]
Manchester	Lake District (Haweswater, Thirlmere) Pennines (Longdendale Chain)	1.750 °Clark / 25 ppm [52]
Birmingham	Elan Valley Reservoirs	3 °Clark / 42.8 ppm [53]
Bristol	Mendip Hills (Bristol Reservoirs)	16 °Clark / 228.5 ppm [54]
Southampton	Bewl Water	18.76 °Clark / 268 ppm [55]
London (EC1A)	Lee Valley Reservoir Chain	19.3 °Clark / 275 ppm [56]
Wrexham (LL11)	Hafren Dyfrdwy	4.77 °Clark [57]

Information from the Drinking Water Inspectorate shows that drinking water in England is generally considered to be 'very hard', with most areas of England, particularly east of a line between the Severn and Tees estuaries, exhibiting above 200 ppm for the calcium carbonate equivalent. Water in London, for example, is mostly obtained from the River Thames and River Lea, both of which derive a significant proportion of their dry weather flow from springs in limestone and chalk aquifers. Wales, Devon, Cornwall, and parts of northwest England are softer water areas and range from 0 to 200 ppm. ^[58] In the brewing industry in England and Wales, water is often deliberately hardened with gypsum in the process of Burtonisation.

Generally, water is mostly hard in urban areas of England where soft water sources are unavailable. Several cities built water supply sources in the 18th century as the Industrial Revolution and urban population burgeoned. Manchester was a notable such city in North West England and its wealthy corporation built several reservoirs at Thirlmere and Haweswater in the Lake District to the north. There is no exposure to limestone or chalk in their headwaters and consequently the water in Manchester is rated as 'very soft'. ^[52] Similarly, tap water in Birmingham is also soft as it is sourced from the Elan Valley Reservoirs in Wales, even though groundwater in the area is hard.

Ireland

The EPA has published a standards handbook for the interpretation of water quality in Ireland in which definitions of water hardness are given. ^[59] Section 36 discusses hardness. Reference to original EU documentation is given, which sets out no limit for hardness. The handbook also gives no "Recommended or Mandatory Limit Values" for hardness. The handbook does indicate that above the midpoint of the ranges defined as "Moderately Hard", effects are seen increasingly: "The chief disadvantages of hard waters are that they neutralise the lathering power of soap [...] and, more important, that they can cause blockage of pipes and severely reduced boiler efficiency because of scale formation. These effects will increase as the hardness rises to and beyond 200 mg/L CaCO
_³."

United States

A collection of data from the United States found that about half the water stations tested had hardness over 120 mg per litre of calcium carbonate equivalent, placing them in the categories "hard" or "very hard". ^[5] The other half were classified as soft or moderately hard. More than 85% of American homes have hard water.^{[ citation needed ]} The softest waters occur in parts of the New England, South Atlantic–Gulf, Pacific Northwest, and Hawaii regions. Moderately hard waters are common in many of the rivers of the Tennessee, Great Lakes, and Alaska regions. Hard and very hard waters are found in some of the streams in most of the regions throughout the country. The hardest waters (greater than 1,000 ppm) are in streams in Texas, New Mexico, Kansas, Arizona, Utah, parts of Colorado, southern Nevada, and southern California. ^{[60] [61]}

See also

• Water portal

• Fouling  – Accumulation of unwanted material on solid surfaces
• Grain (unit)  – Unit of mass
• Water purification  – Process of removing impurities from water
• Water quality  – Assessment against standards for use
• Water treatment  – Process that improves the quality of water

References

1. "Hard water". National Groundwater Association. Retrieved 28 June 2019.
2. "Hardness in Drinking-Water" (PDF). World Health Organization. 2003. Archived from the original (PDF) on 2021-11-05.
3. Weingärtner, Herman] (December 2006). Ullmann's Encyclopedia of Industrial Chemistry – Water. Weinheim: Wiley–VCH. doi:10.1002/14356007.a28_001.
4. "Map showing the rate of hardness in mg/L as Calcium carbonate in England and Wales" (PDF). DEFRA / Drinking Water Inspectorate. 2009.
5. Office of Water Quality. "USGS Water-Quality Information: Water Hardness and Alkalinity". U.S. Geological Survey.
6. Nitsch, Christian; Heitland, Hans-Joachim; Marsen, Horst; Schlüussler, Hans-Joachim (2005). "Cleansing Agents". Ullmann's Encyclopedia of Industrial Chemistry . Weinheim: Wiley–VCH. doi:10.1002/14356007.a07_137.
7. Sengupta, Pallav (August 2013). "Potential Health Impacts of Hard Water". International Journal of Preventive Medicine . 4 (8): 866–875. ISSN   2008-7802. PMC   3775162 . PMID   24049611.
8. "Lime Softening". Archived from the original on 27 October 2016. Retrieved 4 November 2011.
9. Mealy, Rick. "Carbonate chemistry" (PDF). Wisconsin: Department of Natural Resources. Archived from the original (PDF) on 2021-05-18.
10. Lower, Stephen (July 2007). "Hard water and water softening". AquaScams. Retrieved 2007-10-08.
11. PP Coetzee (1998). "Scale reduction and scale modification effects induced by Zn" (PDF). Archived from the original (PDF) on 2016-05-09. Retrieved 2010-03-29.
12. Sorg, Thomas J.; Schock, Michael R.; Lytle, Darren A. (August 1999). "Ion Exchange Softening: Effects on Metal Concentrations". Journal AWWA. 91 (8). American Water Works Association: 85–97. doi:10.1002/j.1551-8833.1999.tb08685.x. ISSN   1551-8833. S2CID   94253149. Archived from the original on 2011-07-26. Retrieved 2010-11-23.
13. "Drinking Water Hardwater Hardness Calcium Magnesium Scale Stained Laundry". Water-research.net. Retrieved 2013-01-26.
14. Kožíšek, František (February 2003). "Health significance of drinking water calcium and magnesium" (PDF). National Institute of Public Health. Archived from the original (PDF) on 2017-01-06 – via Aquasafe Canada.
15. Pocock SJ, Shaper AG, Packham RF (April 1981). "Studies of water quality and cardiovascular disease in the United Kingdom". Science of the Total Environment. 18: 25–34. Bibcode:1981ScTEn..18...25P. doi:10.1016/S0048-9697(81)80047-2. PMID   7233165.
16. Marque S, Jacqmin-Gadda H, Dartigues JF, Commenges D (2003). "Cardiovascular mortality and calcium and magnesium in drinking water: an ecological study in elderly people" (PDF). European Journal of Epidemiology. 18 (4): 305–9. doi:10.1023/A:1023618728056. PMID   12803370. S2CID   1834547.
17. Rubenowitz E, Axelsson G, Rylander R (January 1999). "Magnesium and calcium in drinking water and death from acute myocardial infarction in women". Epidemiology. 10 (1): 31–36. doi: 10.1097/00001648-199901000-00007 . PMID   9888277.
18. Sengupta P (August 2013). "Potential health impacts of hard water". International Journal of Preventive Medicine (Review). 4 (8): 866–875. PMC   3775162 . PMID   24049611.
19. Jabbar-Lopez ZK, Ung CY, Alexander H, Gurung N, Chalmers J, Danby S, et al. (March 2021). "The effect of water hardness on atopic eczema, skin barrier function: A systematic review, meta-analysis". Clinical and Experimental Allergy. 51 (3): 430–451. doi:10.1111/cea.13797. PMID   33259122. S2CID   227245344.
20. "Water Hardness". thekrib.com.
21. Boyd, Claude E. "Prof. Boyd offers a guide for preparing artificial seawater". Global Seafood Alliance. Retrieved 21 December 2023.
22. Wilson, P. Chris. "Water Quality Notes: Alkalinity and Hardness". University of Florida IFAS Extension.
23. "Corrosion by water". corrosionsource. Archived from the original on 2007-10-20.
24. McTigue, Nancy E.; Symons, James M., eds. (2011). The Water Dictionary: A Comprehensive Reference of Water Terminology. American Water Works Association. pp. 333–. ISBN   978-1-61300-101-1.
25. Reid, Robert N. (2003). Water Quality Systems: Guide For Facility Managers. CRC Press. pp. 66ff. ISBN   978-0-8247-4010-8.
26. Langelier, W. F. (October 1936). "The Analytical Control of Anti-Corrosion Water Treatment". Journal of the American Water Works Association. 28 (10): 1500–1521. doi:10.1002/j.1551-8833.1936.tb13785.x. JSTOR   41226418.
27. Aquaprox, ed. (2009). Treatment of cooling water. Springer. pp. 104ff. ISBN   978-3-642-01985-2.
28. Emerson, A. G. D. (2003). Quantitative Forecasting of Problems in Industrial Water Systems. World Scientific. pp. 7ff. ISBN   978-981-238-184-2.
29. Ryznar, John W.; Langelier, W. F. (April 1944). "A New Index for Determining Amount of Calcium Carbonate Scale Formed by a Water". Journal of the American Water Works Association. 36 (4): 472–486. doi:10.1002/j.1551-8833.1944.tb20016.x. JSTOR   23345279.
30. Larson, T. E.; Skold, R. V. (1958). Laboratory Studies Relating Mineral Quality of Water to Corrosion of Steel and Cast Iron. Champaign, Illinois: Illinois State Water Survey. pp. 43–46, ill. ISWS C-71.
31. Stiff, H. A. Jr.; Davis, L. E. (1952). "A Method for Predicting the Tendency of Oil Field Water to Deposit Calcium Carbonate". Petrol Transactions, AIME. 195 (1): 213.
32. Oddo, J. E.; Tomson, M. B. (1992). Scale Control, Prediction and Treatment or How Companies Evaluate a Scaling Problem and What They Do Wrong. CORROSION/92. Houston, Texas: NACE International. Paper No. 34.
33. "Dishwasher and water hardness – Canberra water quality – About Us". ActewAGL. Archived from the original on 2012-03-26.
34. "Quarterly Report" (PDF). Melbourne Water. Archived from the original (PDF) on 2007-09-13. Retrieved 2006-12-17.
35. "Sydney Typical Drinking Water Analysis". Archived from the original on 2013-01-16. Retrieved 2006-12-17.
36. "Drinking Water Quality: Annual report 2005–06" (PDF). Water Corporation. Western Australia. 8 December 2006. Archived from the original (PDF) on 2007-09-04.
37. "Drinking water". Brisbane Water. Archived from the original on 2007-11-02. Retrieved 2006-12-17.
38. "Adelaide Water Quality". Aquasafe Canada. Archived from the original on 2013-03-15. Retrieved 2012-11-30.
39. "Drinking Water Quality". Hobart City Council. Archived from the original on 2008-02-10.
40. "Darwin Water Quality" (PDF). Archived from the original (PDF) on 2007-09-30. Retrieved 2006-12-17.
41. "Tap water in your home". City of Montréal. 2013-01-22. Archived from the original on 2010-03-27. Retrieved 2013-01-26.
42. Canadian Water Quality Association. "Water Hardness/Total Households Canadian Cities" (PDF). Archived from the original (PDF) on 4 October 2013. Retrieved 4 October 2013.
43. "Frequently Asked Questions". City of Saskatoon. Retrieved 2013-01-26.
44. 2006 Winnipeg drinking water quality test results
45. "Water - Services - Living In Toronto - City of Toronto". toronto.ca. 2017-07-14.
46. "GVRD Wash Smart – Water Facts" (PDF). Archived from the original (PDF) on 2006-10-03. Retrieved 2008-01-23.
47. "2021 Water Report CWSC" . Retrieved 2023-12-21.
48. "REGION OF WATERLOO Residential Water Softener Performance Study Testing Report #1 April, 2011" (PDF). Regionofwaterloo.ca. Archived from the original (PDF) on 2017-10-13. Retrieved 2013-01-26.
49. "Public Information Notice: West Side Water Supply". City of Saint John. Archived from the original on 2017-10-10. Retrieved 2017-10-10.
50. Public Works and Environmental Services Department (2019-05-07). "Drinking water - Frequently asked questions". City of Ottawa. Archived from the original on 2020-04-26. Retrieved 2020-06-19.
51. "Table 2 Drinking Water Hardness". United Utilities. Archived from the original on 2012-04-13. Retrieved 2012-03-03.
52. "Drinking water quality". United Utilities. Retrieved 2012-03-03.
53. "Severn Trent Water — B1 1DB". Severn Trent Water. Archived from the original on 2012-05-03. Retrieved 2012-03-03.
54. "Bristol water hardness level". Bristol Water. Archived from the original on 2011-08-01. Retrieved 2012-03-03.
55. "Southern Water — SO14 area". Southern Water. Archived from the original on 2012-11-23. Retrieved 2012-03-03.
56. "EC1A 7BE — Water quality in your area". Thames Water. Archived from the original on 2012-05-27. Retrieved 2012-03-03.
57. "Check my water quality". Hafren Dyfrdwy.
58. "Information about hard water and the affects on your water supply, explained to you by Anglian Water" (PDF). Huntingdon, Cambridgeshire: Anglian Water. Archived from the original (PDF) on 2014-02-22.
59. "Parameters of water quality: interpretation and standards" (PDF). Environmental Protection Agency. 2001. Section 36 "Hardness". Archived from the original (PDF) on 2021-04-14.
60. Briggs, J. C., and Ficke, J.F.; Quality of Rivers of the United States, 1975 Water Year – Based on the National Stream Quality Accounting Network (NASQAN): U.S. Geological Survey Open-File Report 78-200, 436 p. (1977)
61. "Got Hard Water? Here's What You Need To Know About It". Modern Home Pulse. 2018-01-22. Retrieved 2018-09-22.

External links

• "Langelier Saturation Index (LSI) Calculato". Akzo Nobel. Archived from the original on 30 August 2017. Retrieved 29 August 2017.
• "Water hardness unit converter". Archived from the original on 3 February 2010. Retrieved 29 August 2017.
• "UK Hard Water Map". Archived from the original on 2018-01-13. Retrieved 12 January 2018.
• Describes a procedure for determining the hardness of water using EDTA with Eriochrome indicator