Innovia Metro is an automatedrapid transit system manufactured by Alstom. Innovia Metro systems run on conventional metal rails and pull power from a third rail but are powered by a linear induction motor that provides traction by using magnetic force to pull on a "fourth rail" (a flat aluminum slab) placed between the running rails. However, newer versions of the technology are available with standard electric rotary propulsion.
The design was originally developed in the 1970s by the Urban Transportation Development Corporation (UTDC), a Government of Ontario–owned crown corporation. It was designed as a system that would provide economic rapid transit service in the suburbs, which would have ridership levels between what a bus could serve at the low-end, or a subway at the high-end. During development, the system was known as the ICTS (Intermediate Capacity Transit System). The ICTS was chosen for lines in Vancouver, Toronto, and Detroit. Further sales were not forthcoming and the Ontario government lost interest in the company, selling it to Lavalin of Quebec in 1986. Lavalin ran into serious financial difficulties and the UTDC returned to Ontario control, only to be immediately sold to Bombardier Transportation.
Bombardier used the name Advanced Rapid Transit (ART) after its acquisition of the technology. The company was much more active in developing and promoting this system, introducing a major new revision and winning several additional sales in New York City, Beijing, Kuala Lumpur and Yongin, near Seoul.
Bombardier would later be purchased by Alstom, which continues to market the technology. The latest version is marketed as the Innovia Metro, while previous models are retroactively branded as Innovia ART. The largest system is part of the Vancouver SkyTrain metro network, which has seen several major expansions over its lifetime. It operates just under 50 kilometres (31mi) of track compatible with Innovia Metro trains. Vancouver was the first to order Innovia Metro 300 vehicles. Since then, vehicle orders for the latest Innovia Metro technology have been made by transit authorities in Kuala Lumpur and Riyadh.
History
Development stage
During the 1950s, Toronto experienced the same sort of urban sprawl that was sweeping through the United States. This caused enormous traffic problems within the city,[4] and a network of new highways to address the problem became part of the Official Plan in 1959.[5] By the mid-1960s, there was a growing awareness that the growth of the suburbs led to a flight of capital from the city cores, resulting in the urban decay being seen throughout the US leading to freeway revolts across North America. Activists inspired by urbanist Jane Jacobs rallied to oppose development of the Spadina Expressway project.[6] The government reconsidered and cancelled the construction of the Spadina Expressway and other planned expressways.
Instead of expressways, Bill Davis and his new Minister of Transport, Charles MacNaughton, outlined the "GO-Urban" plan. GO-Urban called for a system of three advanced mass transit lines that would be run by the newly formed GO Transit. The idea was to select a system with low capital costs, one that would be cost effective in low-density areas where a traditional subway would be too expensive to build and operate. Designed to have a design capacity half-way between buses and subways, the new system was referred to as the Intermediate Capacity Transit System or ICTS. The space ageautomated guideway transit (AGT) systems being designed in the late 1960s seemed like the right solution.[7]
Toronto was not the only city looking for such a solution, and there appeared to be a large market for automated transit systems in the 1970s and 80s. As GO-Urban was larger than most networks being considered, practically every company working on an AGT, or hoping to, submitted a proposal. The first cut reduced the field to a still-large fourteen proposals. After a year-long selection process, GO selected the Krauss-Maffei Transurbanmaglev as the preferred solution. As a maglev, the system would be silent, addressing concerns about noise on elevated portions of the track. Additionally, the system's linear induction motor did not require physical contact for traction, which meant it would run with equal capacity in snow or icy conditions. Krauss-Maffei agreed to do all vehicle construction in Ontario, and allow the local office to handle all sales efforts in North America – a stipulation most US companies were not willing to agree to. Local testing, construction and sales were centralized in the newly created "Ontario Transportation Development Corporation" (OTDC).[8]
Construction of a test track on the grounds of the Canadian National Exhibition started in late 1975, but shortly after this Krauss-Maffei announced that development funding provided by the German government was ending. Ontario was not willing to continue funding development of the system on their own, and cancelled the maglev plans.[8]
Rebirth
Instead of returning to their earlier submissions, the OTDC decided to press ahead with many portions of the existing ICTS design. On April 14, 1975, the Ministry of Transportation arranged financing for Phase I and II studies to develop the new version. In June 1975, OTDC announced that it had arranged a consortium to continue the development of the ICTS, changing their name to "Urban Transportation Development Corporation" (UTDC) to avoid any "provinciality" during their efforts to market the design to other cities.[9]
The result was essentially a larger, rubber-wheeled version of the original maglev vehicle.[10] The consortium included of SPAR Aerospace for the linear induction motor, Standard Elektrik Lorenz (SEL) for the automatic control system, Dofasco for the bogies, Alcan and Canadair for the design of the car bodies and a set of prototypes, and Canadair as the overall prime contractor.[11] The arrangements, funding and final system definitions were in place by 1976.[12]
Between 1976 and 1980, three prototype cars were built. The first immediately demonstrated a problem with the rubber-wheeled bogies. The linear induction motor required very accurate positioning about 15 millimetres (0.59in) above its "reaction rail" in order to work efficiently and the slight give in the wheels was enough to make this a problem.[9] The obvious solution to this would be to use steel wheels instead, but that would re-introduce the noise problem as the trains rounded curves in the tracks. A new solution was selected, using steel wheels with an articulated bogie that would steer each wheel set into the direction of the track and thereby avoid the rubbing between the flange and track that caused the screeching noise. UTDC bought two modern articulated bogie patents from a private developer in the United States, which were further developed by Dofasco.[13]
A dedicated test facility was desired; modelled after the similar Transit Testing Center set up in the US as part of their own mass transit developments, the site would be open to use for any company that wanted to test new technologies without the need to build out their own testing sites. A 480-acre (190ha) site in Millhaven, outside of Kingston, Ontario, was selected for the new test centre. Kingston had been home to the Canadian Locomotive Company that closed its doors in 1969, and the city lobbied hard for the new company to locate to their city.[citation needed]
The site was officially opened on September 29, 1978, by James Snow, the Minister of Transportation and Communications. The site included a 1.9-kilometre (1.2mi) oval test track that included at-grade, elevated and ramped sections, switches, and the automatic control centre.[14] Phase III of the ICTS program ended on January 31, 1980, when testing on the prototype was completed at the Millhaven site, by this point the government had invested about $57.2million, of a total $63million spent on the product by the government and its industrial partners.[15]
Initial sales
By the late 1970s, it appeared there were no more technology issues to overcome and efforts turned to debugging the system and developing methods for mass production. As this process started, UTDC started its own efforts to market the design. Toronto, the inspiration for the system, was an obvious target, but the company also found interest in the system in Ottawa, Hamilton, Vancouver, Detroit and Los Angeles.
A test system in Toronto was the primary concern. With the GO-Urban concept having since been cancelled, and GO Transit having turned to conventional heavy rail systems, the only suitable local market was the Toronto Transit Commission (TTC). The TTC had recently extended the east–west Bloor-Danforth subway line with the addition of another station on each end of the line, and had planned to further extend the line with streetcars running from those stations into the suburbs. Construction had already started on the streetcar system at the eastern end of the line at Kennedy station.
The provincial government asked the TTC to switch the streetcar line to the ICTS. The TTC was uninterested until the government threatened to pull their financing, which accounted for 75% of its capital budget. In exchange, the government agreed to pay for any cost overruns above the original streetcar budget. Construction of the internal streetcar platform and a turn-around loop had already been completed at the station. The platform had to be raised to the higher floor height of the ICTS, but UTDC claimed the vehicle would be able to make its way around the existing 18-metre (59ft) radius loop at 10km/h (6.2mph) without additional modification.
Vancouver proved very interested in the system on its own merits. As early as 1978, the city had been planning a transportation-themed event for its centennial in 1986, and in 1980 they won the rights to host the Expo '86 World's Fair, giving it the theme "Transportation and Communications". The city is newer than Toronto and more spread out, making a traditional subway unattractive – precisely the problem that the ICTS had been designed to solve. The ICTS vehicle design, with shorter vehicle heights, was also ideal, as the old heavy-rail Dunsmuir Tunnel in downtown Vancouver could be easily modified and split into two stacked tunnels. With UTDC interested in showcasing the system at the Expo, and the Expo backers interested in a transit solution that could be open in time for the show, a deal was quickly arranged that was attractive to both parties. At the time, it was a somewhat controversial project and had its detractors.[16]
Detroit had been one of six cities selected for rapid development under the United States Urban Mass Transportation Administration (UMTA) Downtown People Mover (DPM) program. After ten years, little actual development had taken place and UMTA was mandated to install systems with all possible speed. None of the high-tech developments funded by UMTA had been installed, nor developed to the point where they were ready for service. Instead, the Detroit system was favouring the Cabinentaxi system from Germany, but that company decided to pull out of the contest in order to focus on a larger development in Hamburg. The UTDC responded to a "buy American" clause in UMTA by opening a branch office in Detroit, and that immediately swung the decision in their favour. However, with the Ronald Reagan administration taking office in 1981, DPM was rapidly de-funded. Four of the five cities ended their development plans, but Detroit and Miami (using a different design) decided to press ahead with their deployments.
Construction of the Toronto and Vancouver systems proceeded apace, with the Scarborough RT opening for service on March 22, 1985,[17] followed by the SkyTrain on December 11, 1985, with passenger service starting in January.[18]
Hiatus
Sales of additional ICTS systems went nowhere, and the government began to worry about UTDC's continued successes. The government pushed any potential deployment to buy from UTDC, but with only one product, and that product having many problems in Toronto, there was little interest from other cities. At the same time, the buy-UTDC clause locked Hawker Siddeley Canada out of many local projects, and they had formerly been a major supplier in the local market. The solution was to form a 50–50 combined company, Can-Car Rail, who marketed the combined product line. Hawker had a number of successful products, notably their Bombardier BiLevel Coach, and as these other products were selling well through this period, interest in actively selling ICTS waned.
In spite of Can-Car's success in other markets, as early as 1981 the government had considered selling UTDC to the private sector. Their concern was that without a manufacturing business, UTDC would find it difficult to make enough income to justify its Kingston operations. If the company did start a manufacturing side, it would be inappropriate for the company to remain government owned.[19] The Can-Car deal put this on hold for a time.
In 1986 the new Ontario government announced their intention to sell UTDC to Lavalin, a large engineering company in Montreal. Lavalin purchased the company for only CAD$50million, less than the $70million spent on the UTDC by the government up to 1981.[19] The sale was highly controversial at the time, due to several non-performance payments due to the early problems on the ICTS that had to be paid out by the government, to the tune of $39million. Soon after, Hawker Siddeley announced that they were selling their remaining interest in Can-Car to Lavalin as well.
Innovia ART
Vancouver uses the original Innovia ART 100; the Innovia ART 200 vehicles (pictured here), whose articulated design allows for a more spacious interior; and the ART 300.
A series of financial difficulties caused by Lavalin's rapid expansion led to its bankruptcy. A clause in the original sales contract returned UTDC to Ontario crown control, and they quickly sold it to Bombardier in 1991.[20] Bombardier started a redesign effort for the ICTS, resulting in the larger, advanced rapid transit (ART) Mark II vehicle. Compared to the original ICTS (retroactively named Mark I), the newer ART cars are longer with more seating, and have a more open layout inside.
ART technology was selected for the AirTrain JFK project, which is widely considered a great success in spite of predictions to the contrary. After winning the SkyTrain Millennium Line contract in Vancouver, Bombardier further improved the design by introducing an articulating section between adjacent cars, replacing the coupling and doors of the older Mark I design. The articulation allows passengers to move freely between the cars, as well as adding more internal space for passenger seating. These versions of the Mark II design won several more contracts, and are currently operating on the Kelana Jaya Line in Kuala Lumpur, the Airport Express, Beijing Subway in China (in four-car trains), and the YongIn EverLine near Seoul in South Korea. When Bombardier started marketing ART as part of its Bombardier Innovia family of automated transit systems, the technology was rebranded as the Innovia ART 100 for the Mark I and Innovia ART 200 for the Mark II.
Vancouver continues to be the largest operator of an Innovia ART system, with 49.5km (30.8mi) of operational lines in its SkyTrain network (Expo Line and Millennium Line). This network increased in 2016 with the opening of a 10.9-kilometre (6.8mi) extension of the Millennium Line, named the Evergreen Extension. The SkyTrain system uses a mixed fleet of Innovia ART 100, 200 and 300 cars.
Interior of Mark III car looking toward the end. Notice one side without seats and the larger windows.
Interior of Mark III car looking toward the centre. Notice the walkway and gangway are even wider than the Mark II 2nd generation.
The latest version of the technology uses the name "Innovia Metro" and is marketed as a mid-size metro system. Innovia Metro is compatible with Bombardier's own CITYFLO 650 integrated transit automation system and is offered in variants compatible with both linear motor and electric rotary propulsion. Bombardier now markets the Innovia Metro alongside the larger Movia Metro and has touted its system versatility.
The first rotary-powered Innovia Metro 300 vehicles were ordered by Riyadh Metro in Saudi Arabia for Line 3 of its new rapid transit network. Those 47 vehicles will be equipped with Bombardier's MITRAC propulsion drives.[3]
Design
Control and signalling
The ICTS was the original platform for the SelTrac automated control system by Standard Elektrik Lorenz. This system has changed hands several times since then and is currently owned by Thales. SelTrac is a completely automated system, with centralized control. The system originally used a current loop in the track bed to signal to and from the vehicles, but this has been replaced in more modern versions with a variety of radio systems.
In the original system, the current loop also provided positioning by crossing the lines every metre, with an onboard sensor counting the number of times the polarity changed. Additional fine-tuning was available via a wheel rotation counter, which was used for positioning in stations.
The Toronto Transit Commission union, ATU Local 113, rejected automated control as they felt this was the start of a switch to automating the entire fleet, thereby cutting some of the highest paid jobs in the TTC.[citation needed] This led to the Scarborough Rapid Transit vehicles being modified at a high cost to include operator cabins and conventional controls. No other Innovia Metro system uses manual control.
The Innovia Metro 300 systems are marketed to use Bombardier's own CITYFLO 650 automation system, but can also use other automation systems, such as SelTrac.
The original versions of Innovia Metro were based on a linear induction motor (LIM) using vehicle-mounted windings and a track-mounted stator consisting of a thin aluminum plate mounted flat between the rails. The small size and flat shape of the motor, and its lack of a transmission connected to the bogies, allows the ART to be much closer to the ground than a traditional subway car. The motor is used for all control with the exception of final stopping and positioning using disc brakes and emergency braking using a track brake.
The new Innovia Metro still offers linear motor propulsion as the advantageous option but an electric rotary propulsion version is also an option. The first rotary-powered Innovia Metro 300 system is being implemented in Riyadh, Saudi Arabia.
Vehicle
The Innovia Metro vehicle was built using a lightweight aluminum frame riding on two sets of articulated trucks using small steel wheels. The original Innovia ART 100 cars are 12.7 metres (41ft 8in) long. The second generation Innovia ART 200 cars are 16.7 metres (54ft 9+1⁄2in) long each and come in articulated pairs.
By 2011, the Innovia ART 200 design has been updated and Bombardier is currently marketing the third generation as Innovia Metro 300 (retiring the ART branding). While three vehicle orders have been placed, new vehicles are still in the production stage. Vehicle dimensions are similar to the Innovia ART 200 vehicle, but passenger capacity has been increased through redesigned car layout. The vehicles appear sleeker, with larger windows on the sides of the train, and redesigned windows and headlights on the ends of the cars.
Similar designs
The linear motors and steerable axles used in Innovia Metro trains are relatively rare, although similar Japanese designed linear motor propulsion technologies are also used on a number of subway lines in East Asia, such as the Nagahori Tsurumi-ryokuchi Line, Toei Ōedo Line and Guangzhou Metro Line 5. However, the Innovia Metro system has a number of competitors in the field of automated light metros, including the VAL technology developed by Matra for the Lille Metro in France (and now owned by Siemens) and the Météor technology used by Paris Métro Line 14 (which is built to high-capacity, full metro standards). Furthermore, the CITYFLO and SelTrac signaling technologies are not specific to the Innovia Metro, but can also equip most conventional railway lines regardless of propulsion technology or carrying capacity.
Innovia Metro lines are designed to run on elevated structures, and indeed the systems that use these trains include such sections, with most being predominantly elevated. Using a grade-separated guideway, though, allows them to perform equally well on ground level and in tunnels, as they in fact do for a portion of both Vancouver's Expo and Millennium Lines (using a converted freight tunnel for the Expo line, and a bored tunnel under Clarke Road for the Evergreen Extension), Kuala Lumpur's Kelana Jaya Line, and Beijing's Airport Express. The Scarborough RT in Toronto also includes a short tunnelled section, though there are no stations within it. The Kuala Lumpur and Beijing systems, along with New York's Airtrain JFK, also incorporate platform screen doors commonly found in automated people movers around the world.
Prior to a change in approach to marketing and the introduction of the "Metro" branding, Innovia ART 100 and 200 technologies were sometimes referred to as "light rail", especially in Asia. Because of their use of automated operation and third-rail power, however, they are unsuitable for the unprotected, street-leveltrams that the term usually indicates in Europe and North America.
In 1981, the Toronto Transit Commission (TTC) was planning to build a streetcar line serving the city's eastern district of Scarborough, but the Ontario provincial government convinced it, by threatening to withhold funding, to switch to the Innovia ART 100 technology.[21] This would act as a demonstration system for other transit operators considering buying the trains. In exchange, the government agreed to pay for any cost overruns over the original LRT costs. The 7-kilometre (4.3mi) six-station Scarborough RT (now called Line 3 Scarborough) line opened in March 1985.[21]
Although its Innovia ART 100 trains are capable of driving themselves, the TTC chose to run them semi-automatically with operators on board in order to keep peace with their main union.[citation needed] This conversion proved much more difficult than imagined; the small confines of the Innovia ART 100 car meant that the traditional Toronto solution of taking up the front-right corner of the cab left too little room for the operator to work in, and the entire front of the car had to be used up, reducing seating. Additionally, the Innovia ART 100 control system was based on "dumb" cars and "smart" control centres, so there was no system on the train itself for control or presenting information. These systems had to be retrofitted and were the cause of considerable expense and confusion.
Entering operation, the problems continued. The braking system had been designed to be fully automated but was now being operated by manual control, and the brakes were being over-applied. This led to problems with the wheels being rubbed flat in spots when the brakes were applied too strongly, producing buzzing noises when running at speed. Since the vehicles were brand-new, the TTC did not have a machine capable of grinding the small-diameter wheels, and one had to be purchased for $1.5million.[21] Another $250,000 was needed for a rail grinder to remove "totally unexpected rail corrugations". Additionally, the cars were found to be incapable of turning the short radius, 18-metre (59ft 1in)turning loop at one end of the line, in spite of UTDC's claims it could, which was going to have to be re-built at a cost of about $6million. Instead, this portion of the track was simply abandoned.
Over $1 million was originally budgeted to heat the third rail to prevent ice buildup but this feature was later removed as a cost-cutting move. It was believed that the rapid operation (short headways) would keep the rail free of snow as the passing cars heated the rail. This proved not to be the case and in operations at just the wrong conditions close to freezing, the opposite occurred: when the train passed and heated the rail, microscopically thin layers of snow would be melted, and if the rail was below zero as a whole, the water would freeze to the rail and cause ice buildup. Another retrofit was required to solve this problem, by adding wooden covers over the rail, a system used throughout Toronto's subway system. Even with these covers in place, the line can be shut down by any heavy snowfall that covers the fourth rail to a depth that fills the distance between the rail and the linear motor.
Only two of Line 3's stations have ridership comparable to those of the TTC's conventional subway lines, and most passengers see it merely as an extra transfer they must make in order to get onto a subway line running downtown. Although there had been proposals to extend Line 3, none of these gained traction.
With the Innovia ART 100 fleet overdue for replacement and expensive upgrades to the line needed to handle the longer Innovia ART 200 trains,[22] replacement of the line was decided upon. One proposal would have converted the line to use conventional light rail vehicles and seen it extended west by 19 kilometres (11.8mi),[23] but the city council voted to ask for provincial and federal funding to extend Line 2 Bloor–Danforth, a subway line, from Kennedy station along a new route to Scarborough Centre. Line 3 Scarborough was scheduled to be decommissioned in November 2023, with bus service covering the route until the subway extension opens in 2030. However, an accident involving a car detachment and derailment on July 24, 2023, resulted in the TTC closing the line prematurely.[24]
Vancouver
The SkyTrain metro network has the largest Innovia Metro system in operation, and currently has two such lines: the Expo Line and the Millennium Line. Vancouver's SkyTrain network continues to maintain on-time reliability over 95%. The Expo Line opened in late 1985, in time for Expo '86. With the opening of the Millennium Line in 2002, Vancouver added to its original Innovia ART 100 fleet the longer, articulated Innovia ART 200 trains first used in Kuala Lumpur, which allow for significantly greater rider capacities.
In 2012, Vancouver began construction of the Evergreen Extension, a 10.9-kilometre (6.8mi) extension from Burnaby to Coquitlam in the northeast, which the Millennium Line now re-routes to. Although at one point the extension was proposed to be a street-level LRT system that would not have used Innovia ART technology, in 2008 plans were changed back to the SkyTrain option by the provincial government to facilitate higher ridership from increased capacity, shortened travel times and to integrate seamlessly with the existing SkyTrain network. The extension opened on December 2, 2016.
The network of Innovia ART 100, Innovia ART 200, and Innovia Metro 300 are supported by Quester Tangent products, including braking as well as monitoring and diagnostic equipment.[25]
The 13-station Detroit People Mover is a fully automated system, using the same Innovia ART 100 trains as Toronto and Vancouver. The system had originally been part of UMTA's buildout, which included lines radiating outward from a central circle into the suburbs. However, UMTA was dramatically "downfunded" in the early 1980s, and the Detroit system lost the majority of the funding. Although most other cities on the UMTA list simply gave up on their plans, Detroit decided to press ahead with the portion they could build with the funds they already had, and completed the downtown loop.
The resulting system offers service to a limited area of the downtown core along a 4.7-kilometre (2.9mi) loop. The point-to-point distances are easily walkable, so the system sees low ridership levels on the order of 7,500 passengers a day. Originally designed to act as the hub of a system with 15 million riders a year, the 2million riders it currently serves results in a very high cost-per-passenger. According to The Detroit News, this was about $3 per ride, against a fare of only 50 cents.[citation needed]
The Kelana Jaya Line in Kuala Lumpur, Malaysia, is a fully automated rail line that opened in 1998. It uses the Innovia ART 200 technology, featuring articulated trains. The line spans 37 stations and covers a distance of 46.4 kilometres (28.8mi),[31] making it the longest linear induction motor technology-based line.[clarification needed]
Operation on the line began on September 1, 1998, between the Lembah Subang Depot and Kelana Jaya to Pasar Seni, with the second section from Pasar Seni to Gombak opening in June 1999. By 2002, the line had served 150 million passengers, with an average daily ridership of 160,000. An extension of the line, spanning 17 kilometres (11mi), was completed in 2016.
In 2006, Bombardier was awarded a contract for 22 new four-car trains, with an option for an additional 13 trains if required. The order was expanded in 2007 with an additional purchase of 52 train sets. The first batch of new trains began service in December 2009, and by 2014, all 35 train sets had been delivered.
Following the line extension in 2016, a new order for 14 four-car Innovia Metro 300 trains was placed. The trains feature braking systems, monitoring, and diagnostic equipment developed by Quester Tangent.[25] The trains began entering service at the end of 2016.[32]
In October 2022, Rapid Rail, the operator of the Kelana Jaya Line, announced an order for 19 additional Innovia Metro 300 trainsets (76 cars) at a cost of RM1.72billion (US$385 million).[33][34] The new trainsets were intended to replace the original Innovia Metro 200 trainsets that had been operating on the line since 1999.
The Airport Express of the Beijing Subway, opened in July 2008, uses Innovia ART 200 technology, with a fleet of 40 locally manufactured vehicles.[37] The route is 28 kilometres (17mi) long and has four stations.
Two demonstrator/prototype Innovia ART 100 cars were built and used for testing at the UTDC urban transit facility Millhaven, Ontario.[citation needed] Unlike the production cars, the demo cars lacked doors at either end of the vehicle. Test Vehicle 1 had windows in the centre and on the driver cab, while Test Vehicle 2 is a trailer car only had a centre window and no driver's cab. The paint scheme on the lead car was orange and white, while the trailer was grey and orange. The interior of the vehicle was unfinished (no seats, incomplete floor/ceiling and plywood panelling covering wiring).[citation needed] Only Test Vehicle 2 remained at the facility and in 2011 it was donated to the Canada Science and Technology Museum in Ottawa.
be an articulated version of the Scarborough RT car
be capable of high speeds needed for interurban operation
As the required capacity of the ALRT system rose, it eventually approached the size of conventional heavy rail, and ALRT was cancelled in favour of additional diesel units pulling Bombardier BiLevel Coaches, which have since gone on to be one of Bombardier's best-selling products.
The original ALRT design was never produced, as the ALRT program was cancelled in 1985.
A train derailment in July 2023 resulted in the Toronto Transit Commission permanently closing Toronto’s Line 3 Scarborough, which was the original system that made use of Innovia Metro technology, four months ahead of its scheduled closure in November 2023.[46][47][48]
A scene in the 2003 movie Paycheck, filmed in Vancouver, shows Ben Affleck running in front of a mockup of a Vancouver SkyTrain Innovia ART 200 train. SkyTrain cars can also be seen in the opening credits of 21 Jump Street[49] and variously in Smallville, The X-Files and in numerous other filmed productions shot in Vancouver.
A linear motor is an electric motor that has had its stator and rotor "unrolled", thus, instead of producing a torque (rotation), it produces a linear force along its length. However, linear motors are not necessarily straight. Characteristically, a linear motor's active section has ends, whereas more conventional motors are arranged as a continuous loop.
Line 3 Scarborough, originally known as Scarborough RT (SRT), is a defunct medium-capacity rapid transit line that was part of the Toronto subway system in Toronto, Ontario, Canada. The line ran entirely within the eastern district of Scarborough, encompassing six stations and 6.4 kilometres (4.0 mi) of mostly elevated track. It connected with Line 2 Bloor–Danforth at its southwestern terminus, Kennedy, and terminated in the northeast at McCowan. Until its closure in July 2023, the system had a ridership of 3,908,000 per year.
An automated guideway transit (AGT) or automated fixed-guideway transit or automatic guideway transit system is a type of fixed guideway transit infrastructure with a riding or suspension track that supports and physically guides one or more driverless vehicles along its length. The vehicles are often rubber tired or steel wheeled, but other traction systems including air cushion, suspended monorail and maglev have been implemented. The guideway provides both physical support, like a road, as well as the guidance. An automated line can be cheaper to run than a conventional line, due to the shorter trains and stations.
The Expo Line is the oldest line of the SkyTrain rapid transit system in the Metro Vancouver region of British Columbia, Canada. The line is owned and operated by BC Rapid Transit Company, a subsidiary of TransLink, and links the cities of Vancouver, Burnaby, New Westminster and Surrey.
The Toronto subway is a rapid transit system serving Toronto and the neighbouring city of Vaughan in Ontario, Canada, operated by the Toronto Transit Commission (TTC). The subway system is a rail network consisting of three heavy-capacity rail lines operating predominantly underground. As of October 2024, three new lines are under construction: two light rail lines and one subway line.
An elevated railway or elevated train is a railway with the tracks above street level on a viaduct or other elevated structure. The railway may be broad-gauge, standard-gauge or narrow-gauge railway, light rail, monorail, or a suspension railway. Elevated railways are normally found in urban areas where there would otherwise be multiple level crossings. Usually, the tracks of elevated railways that run on steel viaducts can be seen from street level.
The Urban Transportation Development Corporation Ltd. (UTDC) is a former Crown corporation owned by the Government of Ontario, Canada. It was established in the 1970s as a way to enter what was then expected to be a burgeoning market in advanced light rail mass transit systems. It developed significant expertise in linear propulsion, steerable trucks and driverless system controls which were integrated into a transit system known as the Intermediate Capacity Transit System (ICTS). It was designed to provide service at rider levels between a traditional subway on the upper end and buses and streetcars on the lower, filling a niche aimed at suburbs that were otherwise expensive to service.
Hawker Siddeley Canada was the Canadian unit of the Hawker Siddeley Group of the United Kingdom and manufactured railcars, subway cars, streetcars, aircraft engines and ships from the 1960s to 1980s.
Bombardier Transportation was a Canadian-German rolling stock and rail transport manufacturer, with headquarters in Berlin, Germany. It was one of the world's largest companies in the rail vehicle and equipment manufacturing and servicing industry. Bombardier Transportation had many regional offices, production and development facilities worldwide. It produced a wide range of products including passenger rail vehicles, locomotives, bogies, propulsion and controls. In February 2020, the company had 36,000 employees, and 63 manufacturing and engineering locations around the world. Formerly a division of Bombardier Inc., the company was acquired by French manufacturer Alstom on 29 January 2021.
The LRT Kelana Jaya Line is a medium-capacity light rapid transit (LRT) line and the first fully automated and driverless rail system in the Klang Valley, Malaysia. It forms part of the Klang Valley Integrated Transit System in and around Kuala Lumpur, Malaysia. Servicing 37 stations, the line has 46.4 km (28.8 mi) of grade-separated tracks running mostly on underground and elevated guideways. Formerly known as the PUTRA-LRT, it is operated as part of the Rapid KL system by Rapid Rail, a subsidiary of Prasarana Malaysia. The line is named after its former terminus, the Kelana Jaya station. The line is numbered 5 and coloured ruby on official transit maps.
The H series is the third series of rapid transit rolling stock used in the subway system of Toronto, Ontario, Canada. They were built in six production sets, named H-1 to H-6, from 1965 to 1990 in Thunder Bay, Ontario, for the Toronto Transit Commission (TTC). The entire rolling stock was retired in 2014, though thirteen remaining cars still exist as work cars, including three H-1 cars.
The S series was the rolling stock of light metro used on Line 3 Scarborough, part of the subway system of Toronto, Ontario, Canada. They were built from 1983 to 1986 for the Toronto Transit Commission (TTC) by the Urban Transportation Development Corporation (UTDC) in Millhaven, Ontario. The trains use UTDC's proprietary linear motor-based Intermediate Capacity Transit System and are its Mark I model, which is also used by the Vancouver SkyTrain and the Detroit People Mover. They consist of 14 married pair sets with fleet numbers 3000 to 3027, and are not compatible with the trains on other Toronto lines, which use conventional motors.
SelTrac is a digital railway signalling technology used to automatically control the movements of rail vehicles. It was the first fully automatic moving-block signalling system to be commercially implemented.
The Scharfenberg coupler is a commonly used type of fully automatic railway coupling.
GO ALRT was a rapid transit system proposed by GO Transit in 1982. The ALRT system would have been implemented along two new lines in the Greater Toronto Area. It would have utilized a new electric train to provide interurban service, then referred to as "inter-regional rapid transit", along the existing and new GO corridors. The system was based on an enlarged UTDC ICTS vehicle that was designed to offer a compromise between passenger capacity and the level of infrastructure needed. The project was cancelled due to budget cuts by the Tory government in 1985. However, a number of the proposed lines were later implemented using conventional heavy rail systems, including the eastern portion of the Lakeshore East GO train service route from Pickering station to Whitby station in the Durham region.
Thales Rail Signalling Solutions was a division of Thales Group that supplies transportation-based automation solutions for railways. Its operations are controlled from several locations:
GO-Urban was a planned mass transit project for Greater Toronto to be operated by GO Transit. The system envisioned the use of automated guideway transit vehicles set up in hydro corridors and other unused parcels of land to provide rapid transit services without the expense of constructing tunnels. GO-Urban would serve high-density areas in the downtown core, but also be able to accelerate to high speed between distant stations in the outskirts of the city. Similar deployments were planned for Hamilton and Ottawa.
The SkyTrain is a rapid transit system located in the Metro Vancouver region of the Canadian province of British Columbia, with a number of different models of rolling stock.
McCowan Yard is an inactive rail yard on the Toronto Transit Commission's (TTC's) Line 3 Scarborough of the Toronto subway system. Line 3 permanently closed following a derailment on July 24, 2023.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
Line 3 Scarborough in Toronto, Canada
Detroit People Mover in Detroit, United States
