This article includes a list of general references, but it lacks sufficient corresponding inline citations .(March 2022) |
Panzerkampfwagen VIII Maus | |
---|---|
Type | Super-heavy tank |
Place of origin | Nazi Germany |
Service history | |
Used by | Nazi Germany |
Wars | World War II |
Production history | |
Designer | Ferdinand Porsche |
Designed | 1941 |
Manufacturer | Ferdinand Porsche, Krupp, Alkett |
Produced | 1944 |
No. built | 2 |
Variants | V1, V2 |
Specifications | |
Mass | 188 t (207 short tons; 185 long tons) |
Length | 10.2 m (33 ft 6 in) |
Width | 3.71 m (12 ft 2 in) |
Height | 3.63 m (11 ft 11 in) |
Crew | 6 (commander, gunner, 2 loaders, driver, radio operator/bow gunner) |
Armour | |
Main armament | 128 mm (5 in) KwK 44 gun L/55 (68 rounds) [1] |
Secondary armament |
|
Engine |
|
Power/weight | 6.4 HP/ton [1] |
Ground clearance | 500 mm (20 in) |
Fuel capacity |
|
Operational range |
|
Maximum speed |
Panzerkampfwagen VIII Maus (English: 'mouse') is a German World War II super-heavy tank completed in July of 1944. It is the heaviest fully enclosed armored fighting vehicle ever built. Five were ordered, but only two hulls and one turret were completed, the turret being attached before the testing grounds were captured by advancing Soviet military forces.
These two prototypes underwent trials in late 1944. The complete vehicle was 10.2 m (33 ft) long, 3.71 m (12.2 ft) wide and 3.63 m (11.9 ft) high. Weighing about 188 metric tons, the Maus's main armament was the Krupp-designed 128 mm KwK 44 L/55 gun, based on the 12.8 cm Pak 44 towed anti-tank gun also used in the casemate-type Jagdtiger tank destroyer, with a coaxial 75 mm KwK 44 L/36.5 gun. The 128 mm gun was powerful enough to destroy all Allied armored fighting vehicles in service at the time, with some at ranges exceeding 3,500 m (3,800 yd). [4]
The principal problem in the design of the Maus was developing an engine and drivetrain powerful enough to adequately propel the tank, yet small enough to fit inside it – as it was meant to use the same sort of "hybrid drive", using an internal-combustion engine to operate an electric generator to power its tracks with electric motor units, much as its Porsche-designed predecessors, the VK 30.01 (P), VK 45.01 (P), and Elefant had. The drivetrain was electrical, designed to provide a maximum speed of 20 km/h (12 mph) and a minimum speed of 1.5 km/h (0.9 mph). [5] However, during actual field testing, the maximum speed achieved on hard surfaces was 13 km/h (8.1 mph) with full motor field, and by weakening the motor field to a minimum, a top speed of 22 km/h (14 mph) was achieved. [6] The vehicle's weight made it unable to use most bridges; instead it was intended to ford to a depth of 2 m (6.6 ft) or submerge up to a depth of 8 m (26 ft) and use a snorkel to cross rivers. [7]
The development of the Maus originates from a contract given to Porsche for the design of a 100-ton tank in March 1942. [8] Porsche's design, known as the VK 100.01 / Porsche Type 205, [9] was shown to Adolf Hitler in June 1942, who subsequently approved it. Work on the design began in earnest; the first prototype, to be ready in 1943 was initially to receive the name Mammut ('mammoth'). This was reportedly changed to Mäuschen ('little mouse') in December 1942 and finally to Maus ('mouse') in February 1943, which became the most common name for this tank.
The Maus was designed from the start to use the "electric transmission" design which Ferdinand Porsche had used in the VK 4501 (P), his unsuccessful attempt to win the production contract for the Tiger. The initial powerplant was the Daimler-Benz MB 509 gasoline engine, an adaptation of Germany's largest displacement (at 44.5 L (2,720 cu in)) inverted V12 aircraft engine, the Daimler-Benz DB 603 petrol engine, and later changed to the Daimler-Benz MB 517 diesel engine. This drove an electrical generator, and their combined length occupied the central/rear two-thirds of the Maus' hull, cutting off the forward driver's compartment in the hull from direct access to the turret from within the tank. Each 1.1-meter-wide track, which used the same basic "contact shoe" and "connector link" design format as the Henschel-built Tiger II, was driven by its own electric motor mounted within the upper rear area of each hull side. Each set of tracks had a suspension design containing a total of 24 road wheels per side, in six bogie sets, staggered to be spread over the entire width of the track.
Due to the return "run" of the uniquely 110 cm-wide tracks used being completely enclosed within the fixed outer side armor panels that defined its overall hull width, with the inner vertical lengthwise walls of the hull used to mount the suspension components, a narrow lengthwise "tub" remained between the hull's inner armored walls, under and to the rear of the turret to house the engine and generator of the tank's powertrain. [10]
The armor was substantial: the hull front was 220 mm (8.7 in) thick, the sides and rear of the hull were up to 190 mm (7.5 in). The turret armor was even thicker, the turret front was up to 240 mm (9.4 in) [9] and the sides and rear 200 mm (7.9 in). The gun mantlet was 250 mm (9.8 in), and combined with the turret armor behind, the protection level at that section was even higher.
The initial plan for the Maus was for the prototype to have been completed by mid-1943, with monthly production scheduled to run at ten vehicles per month after delivery of the prototype. The work on the Maus would be divided between Krupp, responsible for the chassis, armament and turret and Alkett, who would be responsible for final assembly.
The Maus tank was originally designed to weigh approximately 100 tons and be armed with a 128 mm main gun and a 75 mm co-axial secondary gun. Additional armament options were studied including various versions of 128 mm, 150 mm, and 170 mm guns. In January 1943 Hitler himself insisted that the armament be a 128 mm main gun with a coaxial 75 mm gun. The 128 mm PaK 44 anti-tank field artillery piece of 1943 that Krupp adapted for arming the Maus as the Kampfwagenkanone (KwK) 44 retained, in parallel to the Porsche project, its original anti-tank Panzerabwehrkanone family designation of PaK 44 when mounted in the casemate-style Jagdtiger tank destroyer.
By May 1943, a wooden mockup of the final Maus configuration was ready and presented to Hitler, who approved it for mass production, ordering a first series of 150. At this point, the estimated weight of the Maus was 188 tons.
In his book Panzer Leader, Heinz Guderian wrote:
On 1 May a wooden model of the "Maus", a tank project of Porsche and Krupp, was shown to Hitler. It was intended to mount a 150 mm gun. The total weight of the tank was supposed to reach 175 ton. It should be considered that after the design changes on Hitler's instructions the tank will weigh 200 ton. The model didn't have a single machine gun for close combat, and for this reason they had to reject it. It had the same design flaw that made the Elefant unsuitable for close combat. In the end, the tank will inevitably have to wage a close combat since it operates in cooperation with the infantry. An intense debate started, and except for me, all of the present found the "Maus" magnificent. It was promising to be exactly that, a "giant". [11]
This lack of close combat armament was later addressed with the addition of a Nahverteidigungswaffe (short-range defensive ordnance) mounted in the turret roof, a 7.92 mm (0.31 in) MG 34 machine gun with 1,000 rounds mounted coaxially with the main weapons in the turret, and three pistol ports for submachine guns in the sides and rear of the turret. Future planned modifications included provisions for a MG 151/20 cannon for anti-aircraft defense mounted in the turret roof. [12]
The first, turretless prototype (V1) was assembled by Alkett in December 1943. Tests started the same month, with a mockup turret fitted of the same weight as the real turret. [9] In June 1944 the production turret, with armament, was used for tests. [9]
The Maus was too heavy to cross bridges. As a result, an alternative system was developed, where the Maus would instead ford the rivers it needed to cross. Due to its size, it could ford relatively deep streams, but for deeper ones it was to submerge and drive across the river bottom. The solution required tanks to be paired up. One Maus would supply electrical power to the crossing vehicle via a cable until it reached the other side. The crew would receive air through a large snorkel, which was long enough for the tank to go 8 m (26 ft) under water.
In March[ citation needed ] 1944 the second prototype, the V2, was delivered. It differed in many details from the V1 prototype. In mid-1944, the V2 prototype was fitted with a powerplant and the first produced Maus turret. This turret was fitted with a 128 mm KwK 44 L/55 gun, a coaxial 75 mm KwK 44 L/36.5 gun and a coaxial 7.92 mm MG 34. The V1 prototype was supposed to be fitted with the second produced turret, but this never happened.
By July 1944, Krupp was in the process of producing four more Maus hulls, but they were ordered to halt production and scrap these. Krupp stopped all work on it in August 1944. Meanwhile, the V2 prototype started tests in September 1944, fitted with a Daimler-Benz MB 517 diesel engine, [9] new electric steering system and a Skoda Works-designed running gear and tracks.
There was also a special railroad carriage made for transporting the Maus prototypes.
After the war, the commander of Soviet armored and mechanized troops ordered the hull of V1 to be mated with the turret of V2. The Soviets used six FAMO-built Sd.Kfz. 9 18t half-tracks, the largest of Germany's half-track vehicles built until May 1945, to pull the 55-ton turret off the destroyed hull. The resulting vehicle was then sent back to the USSR for further testing and is now at Kubinka. [13]
A gunsight intended for the wooden mock-up turret was captured by British forces. [13] It is now in the collection of The Tank Museum at Bovington. [13]
The Tiger II was a German heavy tank of the Second World War. The final official German designation was Panzerkampfwagen Tiger Ausf. B, often shortened to Tiger B. The ordnance inventory designation was Sd.Kfz. 182.. It was also known informally as the Königstiger. Contemporaneous Allied soldiers often called it the King Tiger or Royal Tiger.
The Panzer II is the common name used for a family of German tanks used in World War II. The official German designation was Panzerkampfwagen II.
The Panzerkampfwagen III , commonly known as the Panzer III, was a medium tank developed in the 1930s by Germany, and was used extensively in World War II. The official German ordnance designation was Sd.Kfz. 141. It was intended to fight other armoured fighting vehicles and serve alongside and support the similar Panzer IV, which was originally designed for infantry support.
The Panzerkampfwagen IV, commonly known as the Panzer IV, is a German medium tank developed in the late 1930s and used extensively during the Second World War. Its ordnance inventory designation was Sd.Kfz. 161.
The Panther tank, officially Panzerkampfwagen V Panther with ordnance inventory designation: Sd.Kfz. 171, is a German medium tank of World War II. It was used in most European theatres of World War II from mid-1943 to the end of the war in May 1945.
Elefant was a heavy tank destroyer used by German Panzerjäger during World War II. Ninety-one units were built in 1943 under the name Ferdinand using VK 45.01 (P) tank hulls which had been produced for the Tiger I tank before the competing Henschel design had been selected.
The 15 cm sIG 33 (Sf) auf Panzerkampfwagen 38(t), also known as Grille was a series of self-propelled artillery vehicles used by Nazi Germany during World War II. The Grille series was based on the Czech Panzer 38(t) tank chassis and used a 15 cm sIG 33 infantry gun.
Nazi Germany developed numerous tank designs used in World War II. In addition to domestic designs, Germany also used various captured and foreign-built tanks.
The Entwicklung series, more commonly known as the E-Series, was a late-World War II attempt by Nazi Germany to produce a standardised series of tank designs. There were to be standard designs in five different weight classes from which several specialised variants were to be developed. Design standardisation was envisioned to bring improvements over extreme complexity of previous tank designs that resulted in poor production rates and mechanical unreliability.
The German Panzerkampfwagen Neubaufahrzeug, abbreviated as PzKpfw Nb.Fz, series of tank prototypes were a first attempt to create a medium tank for the Wehrmacht after Adolf Hitler had come to power. Multi-turreted, heavy and slow, they were not considered successful, which led to only five being produced. These were primarily used for propaganda purposes and training, though three took part in the Battle of Norway in 1940. Pictures of the Neubaufahrzeuge were displayed with different turret models and orientations to fool allied spies; American and Soviet agents independently reported that the Germans had two new heavy tanks, the Panzer V and VI. In reality, these tanks were far from the Panzer V Panther and the Panzer VI Tiger.
The Panzerkampfwagen VII Löwe (Lion), initially known as project VK 70.01, was a series of designs for a super-heavy tank developed by Krupp from 1941 to 1942. The project would be cancelled in favour of even heavier tanks such as the Maus.
The Panzerkampfwagen E-100 (TG-01) was a German super-heavy tank design developed towards the end of World War II. It was the largest of the Entwicklung series of tank designs which was intended to improve German armored vehicle production through standardization on cheaper, simpler to build vehicles. By the end of the war, the chassis of the prototype E-100 had been partially completed; it was shipped to the United Kingdom for trials, but was later scrapped. The E-100 Prototype was said to be similar to the Panzerkampfwagen VIII (Maus).
The 10.5 cm K gepanzerte Selbstfahrlafette, also known as the Panzer Selbstfahrlafette IV Ausf. A was a prototype self-propelled gun used by Nazi Germany during World War II. Although it was originally designed as a Schartenbrecher for use against the French Maginot Line defences, following the defeat of France in 1940, it was evaluated for use as a tank destroyer on the Eastern Front.
This article deals with the tanks serving in the German Army throughout history, such as the World War I tanks of the Imperial German Army, the interwar and World War II tanks of the Nazi German Wehrmacht, the Cold War tanks of the West German and East German Armies, all the way to the present day tanks of the Bundeswehr.
The VK 16.02 Leopard was a planned German light reconnaissance vehicle designed from mid-1941 through to January 1943, with serial production scheduled for April 1943. It was intended to be the replacement of Panzer II Ausf. L "Luchs". The project was canceled in January 1943 before the first prototype was completed as it did not meet the requirements for 1944. A wooden mock up of the Waffenträger variant was produced.
The VK 30.01 (P) was the official designation for a heavy tank prototype proposed in Germany. Only two prototype chassis were built. The tank never entered serial production, but was further developed into the VK 45.01 Tiger (P). Porsche called it the Typ (Type) 100.
The VK 45.01 (P), also informally known as Tiger (P) or Porsche Tiger, was a heavy tank prototype designed by Porsche in Germany. With a dual engine gasoline-electric drive that was complex and requiring significant amounts of copper, it lost out to its Henschel competitor on trials, it was not selected for mass production and the Henschel design was produced as the Tiger I. Most of the already produced chassis were rebuilt as Elefant Panzerjäger tank destroyers.
The Panzerkampfwagen III/IV was an experimental medium tank project undertaken by Germany during World War II. The tank was designed to use components of both the Panzer III and Panzer IV, in an attempt to integrate the two projects. The project was cancelled with only the blueprints developed, and no units were ever built.
The Schmalturm was a tank turret designed for use on the Panther Ausf. F medium tank. There was a Krupp proposal to fit it onto the Panzer IV medium tank as well. It featured a narrow front to maximize protection while minimizing weight. It was both lighter and easier to manufacture than the standard Panther turret. The turret had a stereoscopic rangefinder with lenses on either side of the turret, located in spherical bulges. No Schmalturms entered series production.
The Panzerkampfwagen II Ausf. L "Luchs" is a German light tank from the Second World War, developed between 1940 and 1942 by Daimler-Benz and MAN. The Luchs was the only Panzer II design with the Schachtellaufwerk overlapping/interleaved road wheels and "slack track" configuration to enter series production, with 100 being built from September 1943 to January 1944 in addition to the conversion of the four Ausf. M tanks. Originally given the experimental designation VK 13.03, it was adopted under the alternate name Panzerspähwagen II and given the popular name Luchs. The Luchs was larger than the Panzer II Ausf. G in most dimensions. With a six speed transmission, it could reach a speed of 60 km/h (37 mph) with a range of 260 km (160 mi). The FuG 12 and FuG Spr radios were installed, while 330 rounds of 20 mm and 2,250 rounds of 7.92 mm ammunition were carried.
Notes
Bibliography