South African Class 6E1, Series 10

South African Class 6E1, Series 10
E2133 at Nelspruit, 22 October 1990
Type and origin Power type Electric Designer Union Carriage & Wagon Builder Union Carriage & Wagon Model UCW 6E1 Build date 1982-1984 Total produced 55 Rebuilder Transnet Rail Engineering Rebuild date 2001-2005 Number rebuilt 53 to Class 18E, Series 1
Specifications Configuration: ​  •  AAR B-B  •  UIC Bo'Bo'  • Commonwealth Bo-Bo Gauge 3 ft 6 in (1,067 mm) Cape gauge Wheel diameter 1,220 mm (48.03 in) Wheelbase 11,279 mm (37 ft 0 in) ​  •  Bogie 3,430 mm (11 ft 3 in) Pivot centres 7,849 mm (25 ft 9 in) Panto shoes 6,972 mm (22 ft 10+1⁄2 in) Length: ​  • Over couplers 15,494 mm (50 ft 10 in)  • Over body 14,631 mm (48 ft 0 in) Width 2,896 mm (9 ft 6 in) Height: ​  • Pantograph 4,089 mm (13 ft 5 in)  • Body height 3,937 mm (12 ft 11 in) Axle load 22,447 kg (49,487 lb) Adhesive weight 89,788 kg (197,949 lb) Loco weight 89,788 kg (197,949 lb) Electric system/s 3 kV DC catenary Current pickup(s) Pantographs Traction motors Four AEI-283AY ​  • Rating 1 hour 623 kW (835 hp)  • Continuous 563 kW (755 hp) Gear ratio 18:67 Loco brake Air & Regenerative Train brakes Air & Vacuum Couplers AAR knuckle
Performance figures Maximum speed 113 km/h (70 mph) Power output: ​  • 1 hour 2,492 kW (3,342 hp)  • Continuous 2,252 kW (3,020 hp) Tractive effort: ​  • Starting 311 kN (70,000 lbf)  • 1 hour 221 kN (50,000 lbf)  • Continuous 193 kN (43,000 lbf) @ 40 km/h (25 mph)
Career Operators South African Railways Spoornet Class Class 6E1 Number in class 55 Numbers E2086-E2140 Delivered 1982-1984 First run 1982 Last run 2005

The South African Railways Class 6E1, Series 10 of 1982 was an electric locomotive.

Between 1982 and 1984, the South African Railways placed 55 Class 6E1, Series 10 electric locomotives with a Bo-Bo wheel arrangement in service. ^[1]

Manufacturer

The 3 kV DC Class 6E1, Series 10 electric locomotive was designed and built for the South African Railways (SAR) by Union Carriage & Wagon (UCW) in Nigel, Transvaal. The electrical equipment was supplied by the General Electric Company (GEC). ^[2]

Between 1982 and 1984, 55 locomotives were delivered, numbered in the range from E2086 to E2140. Like Series 6 to 9, the Series 10 units were equipped with AEI-283AY traction motors. UCW did not allocate builder's numbers to the locomotives it built for the SAR, but used the SAR unit numbers for their record keeping. ^[1]

Characteristics

Orientation

These dual cab locomotives had a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end was marked as the no. 2 end. A corridor along the centre of the locomotive connected the cabs which were identical apart from the fact that the handbrake was located in cab 2. A pantograph hook stick was stowed in a tube, mounted below the lower edge of the locomotive body on the roof access ladder side. The locomotive had one square and two rectangular access panels along the lower half of the body and a large hatch door below the second small window to the right of the side door on the roof access ladder side, and only one square access panel and a large hatch door below the first window immediately to the right of the door on the opposite side. ^[1]

Series identifying features

The Class 6E1 was produced in eleven series over a period of nearly sixteen years. While some of the Class 6E1 series are visually indistinguishable from their predecessors or successors, some externally visible changes did occur over the years. ^[1]

Drainage holes on Series 9 to 11

Series 8 and later locomotives could be distinguished from all older models by the large hatch door on each side. ^{[1] [3]}

The Series 9 to Series 11 locomotives were visually indistinguishable from each other, but could be distinguished from all earlier models by the rainwater drainage holes on their lower sides. These holes were usually covered by so-called buckets, but the covers were absent on a few locomotives. Another distinction was the end doors, which were recessed into the doorframes on Series 9 to Series 11 locomotives, compared to earlier models which had their end doors flush with the doorframes. In addition, on Series 9 and later, the split side window on the driver's assistant side was replaced by a single rectangular side window with rounded corners. Finally, unlike all earlier models, all four doors on Series 9 to Series 11 locomotives had rounded corners. ^[4]

Crew access

The Class 5E, 5E1, 6E and earlier 6E1 locomotives were notoriously difficult to enter from ground level, since their lever-style door handles were at waist level when standing inside the cab. This made it impossible to open the door from outside without first climbing up high enough to reach the door handle, while hanging on to the side handrails with one hand only. Crews therefore often chose to leave the doors ajar when parking and exiting the locomotives. ^[5]

Side doors with two interconnected latch handles on the outside, such as those which were introduced on the Class 7E1, with one outside handle mounted near floor level and the other at mid-door level, were also introduced on Class 6E1 locomotives beginning with Series 9. ^[6]

Service

The Class 6E1 family saw service all over both 3 kV DC mainline and branch line networks, the smaller Cape Western mainline between Cape Town and Beaufort West and the larger network which covers portions of the Northern Cape, the Free State, Natal, Gauteng, North West and Mpumalanga. ^[7]

Rebuilding to Class 18E

Cab 1 of Class 18E no. 18-108, ex Class 6E1 no. E2114, Capital Park, 1 October 2009

Beginning in 2000, Spoornet began a project to rebuild Series 2 to 11 Class 6E1 locomotives to Class 18E, Series 1 and Series 2 at the Transnet Rail Engineering (TRE) workshops at Koedoespoort. In the process, the cab at the no. 1 end was stripped of all controls and the driver's front and side windows were blanked off to have a toilet installed, thereby forfeiting the locomotive's bi-directional ability. ^{[7] [8]}

Brake rack in Class 18E no. 18-089

Since the driving cab's noise level had to be below 85 decibels, cab 2 was selected as the Class 18E driving cab primarily based on its lower noise level compared to cab 1, which was closer and more exposed to the compressor's noise and vibration. Another factor was the closer proximity of cab 2 to the low voltage switch panel. The fact that the handbrake was located in cab 2 was not a deciding factor but was considered an additional benefit. ^[8]

While the earlier Class 6E1, Series 2 to 7 locomotives had been built with a brake system which consisted of various valves connected to each other with pipes, commonly referred to as a "bicycle frame" brake system, the Class 6E1, Series 8 to 11 locomotives were built with an air equipment frame brake system, commonly referred to as a brake rack. Since the design of the rebuilt Class 18E locomotives included the same brake rack, the rebuilding project was begun with the newer series 8 to 11 locomotives to reduce the overall cost of rebuilding. ^[8]

By June 2005 all Series 10 locomotives except numbers E2111 and E2134 were rebuilt to Class 18E, Series 1. The fate of the two exceptions is not known and they are presumed to have been scrapped. The numbers and renumbering details of the rebuilt units are listed in the table. ^{[7] [8]}

Class 6E1, Series 10 units rebuilt to Class 18E

Count	6E1 no.	Year built	18E no.	18E series	Year rebuilt	Notes
1	E2086	1982	18-158	1	2004
2	E2087	1982	18-046	1	2002
3	E2088	1982	18-089	1	2003
4	E2089	1983	18-023	1	2002
5	E2090	1983	18-130	1	2004
6	E2091	1983	18-176	1	2004
7	E2092	1983	18-164	1	2005
8	E2093	1983	18-059	1	2002
9	E2094	1983	18-126	1	2004
10	E2095	1983	18-039	1	2002
11	E2096	1983	18-174	1	2004
12	E2097	1983	18-180	1	2005
13	E2098	1983	18-179	1	2005
14	E2099	1983	18-053	1	2002
15	E2100	1983	18-149	1	2004
16	E2101	1983	18-166	1	2003
17	E2102	1983	18-044	1	2002
18	E2103	1983	18-175	1	2004
19	E2104	1983	18-160	1	2005
20	E2105	1983	18-102	1	2003
21	E2106	1983	18-004	1	2001
22	E2107	1983	18-186	1	2005
23	E2108	1983	18-177	1	2004
24	E2109	1983	18-081	1	2003
25	E2110	1983	18-052	1	2002
26	E2112	1983	18-060	1	2002
27	E2113	1983	18-151	1	2004
28	E2114	1983	18-108	1	2004
29	E2115	1983	18-191	1	2005
30	E2116	1983	18-099	1	2003
31	E2117	1983	18-155	1	2004
32	E2118	1983	18-096	1	2003
33	E2119	1983	18-024	1	2002
34	E2120	1983	18-122	1	2004
35	E2121	1983	18-113	1	2004
36	E2122	1983	18-085	1	2003
37	E2123	1983	18-103	1	2003
38	E2124	1983	18-076	1	2003
39	E2125	1983	18-016	1	2002
40	E2126	1984	18-082	1	2003
41	E2127	1984	18-131	1	2004
42	E2128	1984	18-032	1	2002
43	E2129	1984	18-043	1	2002
44	E2130	1984	18-121	1	2004
45	E2131	1984	18-040	1	2002	to 18-862
46	E2132	1984	18-047	1	2002
47	E2133	1984	18-123	1	2004
48	E2135	1984	18-114	1	2004
49	E2136	1984	18-132	1	2004
50	E2137	1984	18-115	1	2004
51	E2138	1984	18-088	1	2003
52	E2139	1984	18-128	1	2004
53	E2140	1984	18-153	1	2004

Liveries

All the Class 6E1, Series 10 locomotives were delivered in the SAR red oxide livery with signal red cowcatchers, yellow whiskers and with the number plates on the sides mounted on three-stripe yellow wings. In the 1990s some of the Series 10 units were repainted in the Spoornet orange livery with a yellow and blue chevron pattern on the cowcatchers. ^[9]

References

1. South African Railways Index and Diagrams Electric and Diesel Locomotives, 610mm and 1065mm Gauges, Ref LXD 14/1/100/20, 28 January 1975, as amended
2. "UCW - Electric locomotives" (PDF). The UCW Partnership. Archived from the original (PDF) on 12 October 2007. Retrieved 30 September 2010.
3. Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 128–129. ISBN   0869772112.
4. 18-050 (ex Series 9 E2013) with recessed end door and rounded door corners
5. E1882 with high mounted door handle
6. 18-253 (ex Series 9 E2058) with two door handles
7. Railways of Southern Africa Locomotive Guide, 2002 Edition, (Compiled by John N. Middleton), p57, as amended by Combined Amendment List 4, January 2009
8. Information gathered from the rebuild files of individual locomotives at Transnet Rail Engineering's Koedoespoort shops, or obtained from John Middleton as well as several Transnet employees
9. Soul of A Railway, System 7, Western Transvaal, based in Johannesburg, Part 9. South-Eastwards as far as Volksrust (2nd part) by Les Pivnic. Caption 4. (Accessed on 11 April 2017)

External links

Media related to South African Class 6E1 Series 10 at Wikimedia Commons