M3 Lee

Last updated

Medium Tank, M3
AlfredPalmerM3tank1942b crop2.jpg
Medium Tank, M3, Fort Knox, June 1942
Type Medium tank
Place of origin United States
Service history
In service1941–1955
Wars World War II
Production history
Manufacturer
  • Detroit Tank Arsenal
  • American Locomotive Company
  • Pullman Standard
  • Pressed Steel Car Company
  • Baldwin Locomotive Works
Unit cost$55,250 [1]
ProducedAugust 1941 – December 1942
No. built6,258
VariantsSee Variants
Specifications
Mass30 short tons (27 long tons; 27 t)
Length18 ft 6 in (5.64 m)
Width8 ft 11 in (2.72 m)
Height10 ft 3 in (3.12 m) – Lee
CrewSeven (Lee);
Six (Grant)

Armor
  • 51 mm (2.0 in) hull front, turret front, sides, and rear
  • 38 mm (1.5 in) (hull sides and rear) [2]
Main
armament
Secondary
armament
Engine Wright-Continental R975 EC2
400  hp (300  kW)/340 hp (250 kW)
Transmission Mack Synchromesh, five speeds forward, one reverse
Suspensionvertical volute spring
Ground clearance18 in (0.46 m)
Fuel capacity664 L (175 US gal)
Operational
range
120 mi (193 km)
Maximum speed
  • 26 mph (42 km/h) (road)
  • 16 mph (26 km/h) (off-road)
Steering
system
Controlled differential

The M3 Lee, officially Medium Tank, M3, was an American medium tank used during World War II. The turret was produced in two different forms, one for US needs and one modified to British requirements to place the radio next to the commander. In British Commonwealth service, the tank was called by two names: tanks employing US-pattern turrets were called "Lee", named after Confederate general Robert E. Lee, while those with British-pattern turrets were known as "Grant", named after Union general Ulysses S. Grant.

Contents

Design commenced in July 1940, and the first M3s were operational in late 1941. [3] The US Army needed a medium tank armed with a 75 mm gun and coupled with the United Kingdom's immediate demand for 3,650 medium tanks, [4] the Lee began production by late 1940. The design was a compromise meant to produce a tank as soon as possible and serve only until replaced by the following M4 Sherman tank. The M3 was reliable, had considerable firepower, good armor, and high mobility [5] but had serious drawbacks in its general design and shape, including a high silhouette, an archaic sponson mounting of the main gun preventing the tank from taking a hull-down position, and riveted construction.

It was considered by Hans von Luck (a German army officer who wrote the post-war memoir Panzer Commander), to be superior in May 1942 to the Panzer IV and able to operate out of range of German 5 cm anti-tank guns. [6] However, by mid-1943, with the introduction of upgunned Panzer IIIs and Panzer IVs, the tank had been withdrawn from combat in most theaters and replaced by the more capable M4 Sherman tank as soon as it became available in larger numbers.

Despite its being replaced elsewhere, the British continued to use M3s in combat against the Japanese in southeast Asia until 1945. [7] Nearly a thousand M3s were supplied to the Soviet military under Lend-Lease between 1941 and 1943.

Development

The U.S. funded tank development poorly during the interwar years, and had little experience in design as well as poor doctrine to guide design efforts. Only a few tanks were built (35 between 1920-1935). A new medium tank was designed in 1938, tested as the T5 and accepted as the M2 Medium. The M2 used a radial engine and vertical volute suspension among many of the features of the M2 light tank.

In 1939, the U.S. Army possessed approximately 400 tanks, mostly M2 Light Tanks, with 18 of the M2 Mediums as the only ones considered "modern." [8]

The armor plate on the M3 was too heavy for welding and had to be riveted in position. M3 tank riveting LOC fsa 8e10699.jpg
The armor plate on the M3 was too heavy for welding and had to be riveted in position.

The M2 Medium Tank was typical of armored fighting vehicles (AFVs) many nations produced in 1939. By the time, the U.S. entered the war in 1941, the M2 design was already obsolete with a 37 mm gun, an impractical number of secondary machine guns, a very high silhouette, and 32 mm (1.3 in) frontal armor.

At the end June 1940 the National Munitions Program was introduced to address the United States lack of readiness in case of war across all branches of the armed forces. The program specified the building of over 1,700 medium tanks by the end of 1941. [9] In mid July, Armored Force under Brigadier General Adna R. Chaffee Jr. was formed to take over responsibility for tanks which had previously been split between the Infantry and Cavalry commands. Work was begun with industry to create the production facilities leading to a contract in August for Chrysler to build the Detroit Tank Arsenal which was expected to turn out 10 Medium M2A1 (an improved M2 Medium) per day. [10]

However, the US Army's assessment of the German Panzer III and Panzer IV medium tanks' success in the French campaign was that a 75mm gun was a necessity. [a] The M2A1 could not be fitted with a 75mm weapon in its turret. Producing a new turret design would delay production and while it was decided to start work on a 75mm turret design, an interim solution was sought. An experimental modification of an improved M2 Medium into a self-propelled gun - the T5E2 - had been tested with a 75m pack howitzer in the front hull and it was decided to base the interim design on this work. The existing M2 hull could be used with a redesigned superstructure and the M2A1 37 mm turret [b] . The contract for 1,000 M2A1s was cancelled and replaced with one for 1,000 M3s, though the M3 had not yet been designed. The Ordnance Department allocated 60 days for the design work. [12] At the same time, the 75 mm gun design was started by Watervliet Arsenal; the new gun was based on the 75mm field gun [13]

The design was unusual because the main weapon – a larger caliber, medium-velocity 75 mm gun – was in an offset sponson mounted in the hull with limited traverse. The sponson mount was necessary because, at the time, American tank plants did not have the design experience necessary to make a gun turret capable of holding a 75 mm weapon. A small turret with a lighter, high-velocity 37 mm gun sat on top of the tall hull. A small cupola on top of the turret held a machine gun. The use of two main guns was a feature of the French Char B1 [c] and the Mark I version of the British Churchill tank. [d] In the French tank, it had been designed as a self-propelled gun to attack fortifications and an anti-tank capability had been added through a second gun in a small turret; the Churchill carried a gun in the front hull to fire chiefly smoke shells. The M3 differed slightly from this pattern, having a dual-purpose main gun that could fire an armor-piercing projectile at a velocity high enough for effectively piercing armor, as well as deliver a high-explosive shell that was large enough to be effective. Using a hull-mounted gun, the M3 design could be produced faster than a tank with the same gun in a turret. It was understood that the M3 design was flawed, but Britain [14] urgently needed tanks. A drawback of the sponson mount was that the M3 could not take a hull-down position and use its 75 mm gun at the same time.

The M3 was tall and roomy: the power transmission [e] ran through the crew compartment under the turret basket to the gearbox driving the front sprockets. Steering was by differential braking, with a turning circle of 37 ft (11 m). The vertical volute spring suspension (VVSS) units possessed a return roller mounted directly atop the main housing of each of the six suspension units (three per side), designed as self-contained and readily replaced modular units bolted to the hull sides. The turret was power-traversed by an electro-hydraulic system in the form of an electric motor providing the pressure for the hydraulic motor. This fully rotated the turret in 15 seconds. Control was from a spade grip on the gun. The same motor provided pressure for the gun stabilizing system.

Crew exiting a "disabled tank" during maneuvers held at Camp Polk in February 1943 M3-lee-camp-polk.jpg
Crew exiting a "disabled tank" during maneuvers held at Camp Polk in February 1943

The 75 mm gun was operated by a gunner and a loader; sighting the gun used an M1 periscope – with an integral telescope – on the top of the sponson. The periscope rotated with the gun. The sight was marked from zero to 3,000 yd (2,700 m), [f] with vertical markings to aid deflection shooting at a moving target. The gunner laid the gun on target through geared handwheels for traverse (15° to left and to right) and elevation ( +20° to -9°). [15] The shorter barreled 75 mm M2 cannon sometimes had a counterweight added at the end of the barrel to balance the gun for operation with the gyrostabilizer until the longer 75 mm M3 variant was brought into use. [16]

The 37 mm gun was aimed through the M2 periscope, mounted in the mantlet to the side of the gun. It also sighted the coaxial machine gun. Two range scales were provided: 0–1,500 yd (1,400 m) for the 37 mm and 0–1,000 yd (910 m) for the machine gun. The 37 mm gun also featured a counterweight – a long rod under the barrel – though it was ill maintained by crews who knew little about its use.[ citation needed ]

British Grant (left) and Lee (right) at El Alamein (in the Egyptian Western Desert) 1942, showing differences between the British turret and the original design of the M3 M-3Grants-E 014053.2.jpg
British Grant (left) and Lee (right) at El Alamein (in the Egyptian Western Desert) 1942, showing differences between the British turret and the original design of the M3

There were also two .30-06 (7.62 mm caliber) Browning M1919A4 machine guns mounted in the hull, fixed in traverse but adjustable in elevation, which were controlled by the driver. These were, due to coordination issues, removed, though they would be seen on early Sherman tanks. [17] [g]

Though not at war, the U.S. was willing to produce, sell and ship munitions including armored vehicles to Britain. The British had requested that their Matilda II infantry tank and Crusader cruiser tank designs be made by American factories, but this request was refused. With much of their equipment left in France after the British Army was evacuated from Dunkirk, the equipment needs of the British were acute. Though not entirely satisfied with the design, they ordered the M3 in large numbers. British experts had viewed the mock-up in 1940 and identified features that they considered flaws – the high profile, the hull mounted main gun, the radio position in the hull rather than in the turret, the riveted armor plating (whose rivets tended to pop off inside the interior in a deadly ricochet when the tank was hit even by non-penetrating rounds), the smooth track design, insufficient armor and lack of splash-proofing of the joints. [18]

The British desired modifications for the tank they were purchasing. A bustle rack was to be made at the back of the turret to house the Wireless Set No. 19. The turret was to be given thicker armor than in the original U.S. design, and the machine gun cupola was to be replaced with a simple hatch. Extended space within the turret [h] of the new M3 also allowed the use of a smoke bomb launcher [i] , although the addition of the radio would take the space for storage of fifty 37 mm rounds, reducing the ammunition capacity for that gun to 128 rounds. Several of these new "Grant" tanks would also be equipped with sand shields for action in North Africa, though they often fell off. [17] [20] With these modifications accepted, the British ordered 2,000 Grants, with 1,685 ultimately built.

Contracts were arranged with four US companies for 500 tanks each: Baldwin Locomotive Company, Pullman Standard Car Company, Pressed Steel Car Company and Lima Locomotive Company. The total cost of the orders was approximately US$240 million ($120,000 per piece), including funds for factory re-tooling. That was the total of all UK government funds held in the US; it took the US Lend-Lease act to solve the financial shortfall and fund future equipment orders (for comparison, Lend-Lease cost of a M3 was $64,814). [1] The order with Baldwin was later increased from 500 to 685. Lima did not produce a single Grant against its contract as it took the company so long to complete the steam locomotives already in production to create factory space and to tool-up that M3 production was winding down before it was ready. It was therefore agreed that Lima would supply 500 of the new M4 Sherman instead. Lima actually undertook the T6/M4 development while it was unable to manufacture the Grant and, as the other companies were all too busy, was the first company to begin producing the M4 in March 1942 with the M4A1 variant. The first 28 M4A1s built were British contract tanks as Grant replacements but the remainder of the order was subsumed into Lend-Lease.

The prototype M3 was completed in March 1941 and production models followed, with the first British-specification tanks produced in July. Both U.S. and British tanks had thicker armor than first planned. [21] The British design required one fewer crew member than the US version due to the radio in the turret. The U.S. eventually eliminated the full-time radio operator, assigning the task to the driver. After extensive losses in Africa and Greece, the British realized that to meet their needs for tanks, they would have to take both the Lee and the Grant types.

The U.S. military used the "M" (Model) letter to designate nearly all of its equipment. When the British Army received its new M3 medium tanks from the US, confusion immediately set in [22] between the different M3 medium tank and M3 light tank. The British Army was in the process of using names for its own tanks instead of designations and named its American tanks after American military figures, [19] although the U.S. Army never used those terms until after the war. [23] [24] M3 tanks with the cast turret and radio setup received the name "General Grant", while the original M3s were called "General Lee", or more usually just "Grant" and "Lee". [23] [25]

The chassis and running gear of the M3 design was adapted by the Canadians for their Ram tank. The hull of the M3 was also used for self-propelled artillery as with the original design of the M7 Priest, of which nearly 3,500 were built, and recovery vehicles.

Production

In addition to the Detroit arsenal, American Locomotive and Baldwin Locomotive were brought into the production scheme in October 1940 [26] Neither company needed to also build a factory and so their first tanks were complete - a bit before Detroit's - in April 1941. Even then the shortage of components meant that after American Locomotive's ceremonial driving of its first tank before senior officials, the transmission was removed and sent to Baldwin so that they could carry out a similar ceremony a few days later. The British placed contracts for the Grant with Baldwin, Lima Locomotive and Pullman-Standard in October 1940 [26]

Canada did place an order with Montreal Locomotive Works, a subsidiary of American Locomotive, for the production of over 1000 M3s. [26] but in January this turned into design and production of the Ram tank which was based on the M3 lower hull and suspension.

Production by model and manufacturer [27]
ModelM3M3A1M3A2M3A3M3A4M3A5Grant IGrant IITotal
American Locomotive Company 285300685
Baldwin Locomotive Works 8422392102214641,220
Detroit Tank Arsenal 3,2431093,352
Pressed Steel Car Company 501501
Pullman-Standard Car Company 500500

Operational history

Of the 6,258 M3 variants manufactured, 2,887 (45%) were supplied to the British government for use by British and Commonwealth forces. [28] 1,685 of these were Grants which the UK ordered directly from US industry for cash and which did not fall under the Lend-Lease arrangements.

The M3 Grant first saw action with units of the Royal Armoured Corps in North Africa during the Gazala battles of May 1942. However, with the arrival of the M4 Sherman tank from October 1942 the surviving M3s in North Africa became surplus and were mostly shipped on to India. 657 Grants and 75 Lees were supplied directly to North Africa.

Ninety-seven Grants and 119 M3 Lees - including 49 diesel M3A3 Lee Vs, the only diesel Lees used by UK and Commonwealth forces - were supplied directly to the UK and were used for testing and training. 335 were later converted to Canal Defense Lights (no diesels), and further refurbished turretless M3 hulls were supplied by the US to support this project.

777 were supplied directly to the Australian Army for home defense and training duties in Australia. [29] None were used operationally. These comprised 255 Lee Is, 266 Grant Is and 232 Grant IIs. The British Indian Army received 896 M3 series tanks as new supply and tanks shipped from North Africa. These comprised 517 Lee Is and 379 Grant Is.

A further 1,386 were exported to the Soviet Union, [30] although only 957 of these reached Russian ports due to German U-boat and air attacks on Allied convoys. [31]

North African campaign

The M3 brought much-needed firepower to British forces in the campaign in the North African desert. Early Grants were shipped directly to Egypt and lacked some fitments (such as radio) that were remedied locally. Under the "Mechanisation Experimental Establishment (Middle East)" other modifications were tested approved and made to tanks as they were issued. These included fitting of sand shields (later deliveries from the US had factory fitted shields), dust covers for the gun mantlets and the removal of the hull machine guns. Ammunition stowage was altered to 80 x 75 mm (up from 50) and 80 x 37 mm with additional protection to the ammunition bins.

Grants arrived in North Africa by the end of January 1942, and British crews began training on them. As it was developed from the World War I-era French 75 mm gun, the British had ammunition stocks left over from then that could be used for the 75 mm M2 gun but these suffered due to age. The armor-piercing shell for the 75 mm was a solid shot and could penetrate around 2 inches (50 mm) of armor at 1,000 m, which was better than the 2-pounder guns of British tanks, but better performance was desired. Fortunately, large numbers of German 75 mm shells were captured, and these were matched to the American cartridge. This conversion gave improved performance and was followed by an improved American AP shell design (the M61). While the Grants had been expected to be a temporary until the Crusader Mark III tank with a 57 mm 6-pounder gun was available, problems with the Crusader led to changes. The Grant became the main tank in use, and cruiser tanks such as the Crusader Mk I and II replaced the M3 light tank in British units. [19]

Crew of M3 tank at Souk el Arba, Tunisia, November 23, 1942. SC167334t.jpg
Crew of M3 tank at Souk el Arba, Tunisia, November 23, 1942.

The M3 tank's first action during the war was in 1942 during the North African Campaign. [32] British Lees and Grants were in action against Rommel's forces at the Battle of Gazala on 27 May. In the preparations for the battle the Eighth Army received 167 M3 tanks. The 8th King's Royal Irish Hussars, 3rd and 5th battalions Royal Tank Regiment went into action with Grant tanks. Retreating in the face of a large attack, the 8th Hussars had only three Grants remaining, while 3rd RTR reported losing 16.

Their appearance was a surprise to the Germans, who were unprepared for the M3's 75 mm gun. They soon discovered the M3 could engage them beyond the effective range of their 5 cm Pak 38 anti-tank gun, and the 5 cm KwK 39 of the Panzer III, their main medium tank. The M3 was also vastly superior to the Fiat M13/40 and M14/41 tanks employed by the Italian troops, whose 47 mm gun was effective only at point-blank range, while only the few Semoventi da 75/18 self-propelled guns were able to destroy it using HEAT rounds. [33] In addition to the M3's superior range, they were equipped with high explosive shells for infantry and other soft targets, which previous British tanks had lacked; upon the introduction of the M3, Rommel noted: "Up to May of 1942, our tanks had in general been superior in quality to the corresponding British types. This was now no longer true, at least not to the same extent." [34]

Despite the M3's advantages and surprise appearance during the Battle of Gazala, it could not win the battle for the British. In particular, the high-velocity 88 mm anti-aircraft gun, in use as its secondary role of an anti-tank gun, proved deadly if British tanks attacked without artillery support. [35] Britain's Director of Armoured Fighting Vehicles nonetheless said before the M4 Sherman arrived that "The Grants and the Lees have proven to be the mainstay of the fighting forces in the Middle East; their great reliability, powerful armament and sound armor have endeared them to the troops." [36]

By the Second Battle of El Alamein in late 1942, there were 600 M3s, of both types, in British service. Some of these were used for training in the UK.

Grants and Lees served with British units in North Africa until the end of the campaign. Following Operation Torch (the invasion of French North Africa), the US also fought in North Africa using the M3 Lee.

The US 1st Armored Division had been issued the new M4 Sherman, but had given up one regiment's worth to the British Army so that it could use them in the Second Battle of El Alamein (October-November 1942). Consequently, a regiment of the division was still using the M3 Lee when it arrived in North Africa.

The M3 was generally appreciated during the North African campaign for its mechanical reliability, good armor protection, and heavy firepower. [j] In all three aspects, the M3 was capable of engaging German tanks and towed anti-tank guns.[ citation needed ]

However, the high silhouette and low, hull-mounted 75 mm were tactical drawbacks since they prevented fighting from a hull-down firing position. In addition, the use of riveted hull superstructure armor on the early versions led to spalling, where the impact of enemy shells caused the rivets to break off and become projectiles inside the tank. Later models were built with all-welded armor to eliminate this problem. These lessons had already been applied to the design and production of the M4.

The M3 was replaced in front-line roles by the Sherman as soon as it became available. However, several specialist vehicles based on the M3 were later employed in Europe, such as the M31 armored recovery vehicle and the Canal Defence Light.

In early 1943, the British Eight Army's M3s, now replaced by the Sherman, were shipped to the Pacific theatre to replace some Matildas in the Australian Army.

Eastern Europe—Soviet service

A company of M3 Lee tanks of the Soviet 6th Guards Army advance towards the front line during the Battle of Kursk, July 1943 Soviet M3 Lee tanks of the 6th Guards Army Kursk July 1943.jpg
A company of M3 Lee tanks of the Soviet 6th Guards Army advance towards the front line during the Battle of Kursk, July 1943

Beginning from 1941, 1,386 M3 medium tanks were shipped from the US to the Soviet Union, with 417 lost when their transporting vessels were sunk by German submarine, naval and aerial attacks en route. [31] [38] These were supplied through the American Lend-Lease program between 1942 and 1943.

Soviet Red Army personnel tended to refer to the M3 as the "Grant", even though all of the M3s shipped to Russia were "Lee" variants. The official Soviet designation for it was the М3 средний (М3с), or "M3 Medium", to distinguish the Lee from the US-built M3 Stuart light tank, which was also acquired by the USSR under Lend-Lease and was officially known there as the М3 лёгкий (М3л), or "M3 Light". [39]

Due to the vehicle's petrol-fueled engine, a high tendency to catch fire, and its vulnerability against most types of German armor the Soviet troops encountered from 1942 onwards, the tank was almost entirely unpopular with the Red Army since its introduction in the Eastern Front. [40] In the letter sent to Franklin Roosevelt (18 July 1942), Stalin wrote: "I consider it my duty to warn you that, according to our experts at the front, U.S. tanks catch fire very easily when hit from behind or from the side by anti-tank rifle bullets. The reason is that the high-grade gasoline used forms inside the tank a thick layer of highly inflammable fumes." [41] [ check quotation syntax ] With almost 1,500 Russian T-34 tanks being built every month, Soviet use of the M3 medium tank declined soon after mid-1943. Soviet troops still fielded their Lee/Grant tanks on secondary and less active fronts, such as in the Arctic region during the Red Army's Petsamo–Kirkenes Offensive against German forces in Norway in October 1944, where the obsolete US tanks faced mainly captured French tanks used by the Germans, such as the SOMUA S35, which to a limited extent was somewhat comparable to the Lee/Grant it fought against.

Pacific War

In the Pacific War, armor played a relatively minor role for the Allies as well as for the Japanese, compared with that of naval, [42] air, [43] and infantry units.

In the Pacific Ocean Theater and the Southwest Pacific Theater, the US Army deployed none of its dedicated armored divisions and only a third of its 70 separate tank battalions.

A small number of M3 Lees saw action in the central Pacific Ocean Theater in 1943. The US Marine Corps, [44] bypassed the M3 Lees, switching from M3 Stuarts directly to M4 Shermans in mid-1944. [45]

Some M3 Grants played an offensive role with the British Indian Army, in the south-east Asian theater.

The Australian Army also used Grants during World War II, mainly for homeland defense and training purposes.

Pacific Ocean Theater

US Army M3A5 Lees during the Battle of Makin M3 Medium Tanks in the Battle of Makin.png
US Army M3A5 Lees during the Battle of Makin

The only combat use of the M3 Lee by the US Army against Japanese forces [46] occurred during the Gilbert and Marshall Islands campaign of 1943.

Following the better-known landing at Tarawa, the US 27th Infantry Division made an amphibious assault on Makin Island with armored support from a platoon of M3A5 Lees equipped with deep-wading kits belonging to the US Army's 193rd Tank Battalion.

Burma

A British M3 Lee in Mandalay, Burma (Myanmar), during the Burma Campaign in March 1945. Spare tracks are welded onto the front glacis for extra protection. The British Army in Burma 1945 SE3270.jpg
A British M3 Lee in Mandalay, Burma (Myanmar), during the Burma Campaign in March 1945. Spare tracks are welded onto the front glacis for extra protection.

After British Commonwealth forces in Europe and the Mediterranean began receiving M4 Shermans, about 900 British-ordered M3 Lees/Grants were shipped to the Indian Army. Some of these saw action against Japanese troops and tanks in the Burma Campaign. [29]

They were used by the British Fourteenth Army [47] until the fall of Rangoon, [47] regarded as performing "admirably" in their original intended role of supporting infantry in Burma between 1944 and 1945. [47] [48] It played a pivotal role during the Battle of Imphal, during which the Imperial Japanese Army's 14th Tank Regiment (primarily equipped with their own Type 95 Ha-Go light tanks, together with a handful of captured British M3 Stuart light tanks) encountered M3 medium tanks for the first time and found their light tanks outgunned and outmatched. [49] The British M3 tanks performed well as they traversed the steep hillsides around Imphal and defeated the assaulting Japanese forces. Officially declared obsolete in April 1944, [47] nevertheless, the Lee/Grant saw action until the end of the war in September 1945.

Australia

At the beginning of the war, Australian Army doctrine viewed tank units as minor offensive components within infantry divisions. It had no dedicated armored branch and most of its very limited capabilities in tank warfare had been deployed to the North African Campaign (i.e. three divisional cavalry battalions). By early 1941, the effectiveness of large-scale German panzer attacks had been recognized, and a dedicated armored mustering was formed. The Australian Armoured Corps initially included the cadres of three armored divisions – all of which were equipped at least partly with M3 Grants made available from surplus British orders.

The 1st Australian Armoured Division was formed with a view towards complementing the three Australian infantry divisions then in North Africa. However, following the outbreak of hostilities with Japan, [50] the division was retained in Australia. During April–May 1942, the 1st Armoured Division's regiments were reported to be re-equipping with M3 Grants and were training, in a series of large exercises, in the area around Narrabri. [50]

The cadres of the 2nd and 3rd Armoured Divisions were both officially formed in 1942, as Militia (reserve/home defense) units. These divisions were also partly equipped with M3 Grants. [51]

In January 1943, the main body of the 1st Armoured Division was deployed to home defense duties between Perth and Geraldton, where it formed part of III Corps. [50]

By the middle of the war, the Australian Army had deemed the Grant to be unsuitable for combat duties overseas, and M3 units were re-equipped with the Matilda II before being deployed to the New Guinea and Borneo Campaigns. Due to personnel shortages, all three divisions were officially disbanded during 1943 and downgraded to brigade- and battalion-level units. [51]

Post-war use in Australia

During the war, the Australian Army had converted some M3 Grants for special purposes, including a small number of bulldozer variants, beach armoured recovery vehicles, and wader prototypes.

Following the end of the war, 14 of the Australian M3A5 Grants were converted to a local self-propelled gun design, the Yeramba. Until the future acquisition of the AS9 Huntsman [52] is complete, the Yeramba remains as the only SPG ever deployed by the Australian Army. [53] Fitted with a 25-pounder field gun, the Yerambas remained in service with the 22nd Field Regiment, Royal Australian Artillery, until the late 1950s.

Many M3s deemed surplus to Australian Army requirements were acquired by civilian buyers during the 1950s and 1960s for conversion to earthmoving equipment and tractors.

Conclusion

Overall, the M3 was able to be effective on the battlefield from 1942 until 1943. However, US armored units lacked the tactical expertise to overcome its design. [54] Its armor and firepower were equal or superior to most of the threats it faced, especially in the Pacific. Long-range, high-velocity guns were not yet common on German tanks in the African theater. However, the rapid pace of tank development meant that the M3 was very quickly outclassed. By mid-1942, with the introduction of the German Tiger I, the up-gunning of the Panzer IV to a long 75 mm gun, and the first appearance in 1943 of the Panther, along with the availability of large numbers of the M4 Sherman, the M3 was withdrawn from service in the European theater.[ citation needed ]

Variants

M3 and its contribution to other AFVs of the Second World War. M3 and relatives.PNG
M3 and its contribution to other AFVs of the Second World War.
M31B1 TRV showing dummy hull gun. M31-ARV-batey-haosef-2.jpg
M31B1 TRV showing dummy hull gun.
M3 Lees on the production line at Chrysler's Detroit Arsenal M3-lee-chrysler-arsenal-2.jpg
M3 Lees on the production line at Chrysler's Detroit Arsenal

US variants

American designations first with British Commonwealth designations (where actually used) given in parentheses.

M3 (Lee I)
Original baseline design. Riveted hull. Continental radial gasoline engine. 4,724 built.
M3A1
Cast (rounded) upper hull variant. 300 built. 28 were experimentally converted with the Guiberson T-1400-2 350 hp radial diesel engine, which proved unsatisfactory. Never used operationally.
M3A2
Welded hull version of baseline M3. Only 12 produced, 10 of which were completed as Grant I. At least 1 of these was supplied to Australia and another was converted to a Grant Scorpion.
M3A3 (Lee V)
Diesel-engined variant with welded hull. Twin GM 6-71 diesel engines coupled together to make the GM6046 powerpack. Side doors welded shut or later eliminated. 288 built, 49 supplied to the UK and 77 supplied to Brazil. 83 M3A3 hulls completed as Grant II.
M3A4
Stretched riveted hull to accommodate the Chrysler A57 multibank engine, made up of five 4.12 liter displacement, 6-cyl L-head car engines (block upwards) mated to a common crankshaft. Displacement 21 liters, 470  hp (350  kW ; 480  PS ) at 2,700 rpm. Side doors eliminated. 109 built. Only used for training in the US.
M3A5
Rivetted hull but otherwise as per the M3A3. 591 built, 387 as Grant IIs. Only used operationally once by US forces. 23 supplied to Brazil.
M31 Tank Recovery Vehicle (Grant ARV I)
Based on M3 chassis, with dummy turret and guns. A 60,000 lb (27,000 kg) winch installed.
M31B1 Tank Recovery Vehicle
Based on M3A3.
M31B2 Tank Recovery Vehicle
Based on M3A5.
There were 296 total M31B1/B2 vehicles, although the precise quantity of both variants is unknown (it appears that M31B1 was more common). 146 of them were converted from used tanks and 150 from newly built tanks before their acceptance.
M33 Prime Mover
M31 TRV converted to the artillery tractor role, with turret and crane removed. 109 vehicles were converted in 1943-44.
105 mm Howitzer Motor Carriage M7 (Priest)
105 mm M1/M2 howitzer installed in open superstructure. A gunless version was used as an observation post (OP) vehicle
155 mm Gun Motor Carriage M12
Designed as the T6. A 155 mm howitzer on M3 chassis. 100 built in 1942-1943. M30 Cargo Carrier on same chassis to transport gun crew and ammunition.

British Commonwealth service names and variants

Grant Command variant used in North Africa by Lieutenant-General Montgomery, preserved in the Imperial War Museum Duxford Grant II Command tank "Monty" - IWM Duxford (51295549779).jpg
Grant Command variant used in North Africa by Lieutenant-General Montgomery, preserved in the Imperial War Museum Duxford

Australian variants

The Australian M3 BARV. Puckapunyal-M3-BARV-1.jpg
The Australian M3 BARV.

Designs based on chassis

Operators

World War II operators of the M3 M3 Lee operators map.PNG
World War II operators of the M3

See also

Notes

Explanatory footnotes

  1. The Panzer IV was the only German tank with a 75mm gun, which was a short barrelled weapon- the 7.5 cm KwK 37 for infantry support use.
  2. The 37 mm turret mounted on the M3 design replaced the rangefinder turret of the T5E2 design. [11]
  3. The Char B1 was designed as a self-propelled gun for use against fortifications and a turret was added to give anti-tank capability
  4. The first Churchills had a howitzer to fire smoke shells in the hull
  5. Designed by Spicer Manufacturing Company and manufactured by Mack Manufacturing and, later, Iowa Transmission Company.
  6. later 3,500 yards
  7. Two of the seven machine guns on the M2 Medium had also been in the forward hull under the drivers control.
  8. Designed by L.E. Carr of the British Department of Mechanization and tested on a M2A1 Medium [19]
  9. The "2-inch Mortar Mk III (smoke)"
  10. Initially there were problems with engine wear and suspension springs. [37]

Citations

  1. 1 2 Zaloga, Steven (2015). Armored Champion: The Top Tanks of World War II. Stackpole Books. p. 39. ISBN   978-0-8117-6133-8 . Retrieved 14 May 2023.
  2. AFV Database
  3. Zaloga p. 16 & 20
  4. Zaloga 2008 p. 20 & 21
  5. USSR Red Army GABTU (Main Directorate of Armoured Forces) off-road trials May 1942 "The American Highrise".
  6. von Luck, Hans (2013) [1989]. "North Africa, 1942: Rommel, the Desert Fox". Panzer Commander: The Memoirs of Colonel Hans von Luck. Dell. p. Paragraph 6.75.
  7. "The British Army in Burma 1945". Imperial War Museum.
  8. Hunnicutt 1978 p. 44
  9. Chamberlain & Ellis p7
  10. Chamberlain & Ellis p9-10
  11. Chamberlain & Ellis p11
  12. Chamberlain & Ellis p11
  13. Chamberlain & Ellis p14
  14. Zaloga, Armored Thunderbolt, p. 21
  15. Rottman 2008, p. 32
  16. "Medium Tank M3 Lee"
  17. 1 2 Moran, Nicholas. Inside the Chieftain's Hatch: M3 Grant. Part 1. youtube. World of Tanks North America.
  18. Fletcher, Great Tank Scandal, p. 90.
  19. 1 2 3 "Lee and Grant: American Generals in British Service". Tank Archives. Retrieved 28 October 2023.
  20. Moran, Nicholas. Inside the Chieftain's Hatch: M3 Grant. Part 2. youtube. World of Tanks North America.
  21. Fletcher, Great Tank Scandal, p. 93.
  22. Zaloga (Armored Thunderbolt) p. 18
  23. 1 2 Stout, Wesley W. (1946). Tanks are Mighty Fine Things. Chrysler Corporation. p.  136 . Retrieved 11 July 2019.
  24. Zaloga (Armored Thunderbolt) p. 19
  25. Bishop The Encyclopedia of Weapons of World War II p. 34
  26. 1 2 3 Chamberlain & Ellis p18
  27. Zaloga 2005, p. 13.
  28. "Section III-A Ordnance General Supplies", Quantities of Lend-Lease Shipments, War Department, p. 8, 1946 via Hyperwar Foundation
  29. 1 2 Zaloga (2008) p. 30-31
  30. Zaloga (2008) p. 28, 30, 31
  31. 1 2 Lend-Lease tanks and aircrafts [sic]
  32. Zaloga (2008) p. 28
  33. Cappellano, F.; Battistelli, P.P (2012). Italian Medium Tanks: 1939-45 . New Vanguard 195. Oxford: Osprey Publishing. pp.  34–38. ISBN   9781849087759 via Archive.org.
  34. Hart, Liddell. The Rommel Papers. p. 196.
  35. The M-3 Grant: America's Nazi Germany Tank-Killer - Michael Peck Nationalinterest.org, 22 January 2017
  36. Stout, Wesley W. (1946). Tanks are Mighty Fine Things. Chrysler Corporation. pp.  137–138. Retrieved 11 July 2019.
  37. Fletcher, Great Tank Scandal, p. 92.
  38. Барятинский М. П. «Трёхэтажный» американец Сталина. Танк M3 «Генерал Ли» / «Генерал Грант». — М.: Яуза, Эксмо, 2011. — 104 с. — (Арсенал коллекция). — 1700 экз. — (in Russian), Litres, 25 July 2019, ISBN   978-5-699-49808-6
  39. Лёгкий танк M3/M5 «Генерал Стюарт» (In Russian), "M3/M5 General Stuart Light Tank" from (Baryatinsky M. Armored Vehicles of the USA 1939-1945 — Moscow: Modelist-Constructor, 2009. — 40 p. — (Armored Collection. 2009. № 1 (82)) via armor.kiev.ua
  40. Winchester, Charles D.; Drury, Ian (20 August 2011). Hitler's War on Russia. Bloomsbury Publishing. pp. 138–. ISBN   978-1-84908-995-1.
  41. "Correspondence between the Chairman of the Council of Ministers of the USSR and the Presidents of the USA and the Prime Ministers of Great Britain during the Great Patriotic War of 1941 - 1945".
  42. Zaloga 2007, back cover & p. 3
  43. Ewing p. VII
  44. Zaloga (Armored Thunderbolt) p. 24 & 301
  45. USMC TOEs [ page needed ]
  46. Zaloga 2008 p. 305
  47. 1 2 3 4 Hunnicutt (1978) p. 105
  48. Zaloga 2008 p. 31
  49. Zaloga (Japanese Tanks 1939-45) p. 40
  50. 1 2 3 Zach Lambert, 2012, "The Birth, Life and Death of the 1st Australian Armoured Division" Archived 2018-01-03 at the Wayback Machine , Australian Army Journal vol. 9, no. 1, pp. 96–97.
  51. 1 2 Ronald Hopkins, 1978, Australian Armour: A History of the Royal Australian Armoured Corps 1927–1972, Puckapunyal, Royal Australian Armoured Corps Tank Museum, pp. 125–130, 326.
  52. Marquis, Nicholas (4 July 2023). "Self-propelled howitzer a game-changer". Australian Defence Force . Archived from the original on 11 July 2023. Retrieved 29 July 2023.
  53. Gower, Stephen N.; Cecil, Mike (Winter 2004). "Yeramba : a 'great piece of artillery '". Wartime. No. 27. Australian War Memorial. p. 35 - 37.
  54. Porter (Allied Tanks of World War II 1339-1945 The World's Greatest Weapons) p. 77
  55. 1 2 3 4 Chamberlain & Ellis 1981 p113
  56. Chamberlain & Ellis 1981 p110
  57. Greg Kelley; Jason Long. "Romanian Armour in World War Two". Archived from the original on 26 September 2003.
  58. Mark Axworthy, Cornel I. Scafeș, Cristian Crăciunoiu, Third Axis, Fourth Ally: Romanian Armed Forces in the European War, 1941–1945, p. 221

General references

Further reading

Related Research Articles

<span class="mw-page-title-main">Tank destroyer</span> Armoured fighting vehicle designed to engage and destroy enemy tanks

A tank destroyer, tank hunter or tank killer is a type of armoured fighting vehicle, predominantly intended for anti-tank duties. They are typically armed with a direct fire artillery gun, also known as a self-propelled anti-tank gun, or missile launcher, also called an anti-tank missile carrier. The vehicles are designed specifically to engage and destroy enemy tanks, often with limited operational capacities.

<span class="mw-page-title-main">M4 Sherman</span> American medium tank widely used during World War 2

The M4 Sherman, officially medium tank, M4, was the medium tank most widely used by the United States and Western Allies in World War II. The M4 Sherman proved to be reliable, relatively cheap to produce, and available in great numbers. It was also the basis of several other armored fighting vehicles including self-propelled artillery, tank destroyers, and armored recovery vehicles. Tens of thousands were distributed through the Lend-Lease program to the British Commonwealth, Soviet Union, and other Allied Nations. The tank was named by the British after the American Civil War General William Tecumseh Sherman.

<span class="mw-page-title-main">Panzer III</span> German medium tank of the 1930s and World War II

The Panzerkampfwagen III , commonly known as the Panzer III, was a medium tank developed in the 1930s by Germany, and was used extensively in World War II. The official German ordnance designation was Sd.Kfz. 141. It was intended to fight other armoured fighting vehicles and serve alongside and support the similar Panzer IV, which was originally designed for infantry support.

<span class="mw-page-title-main">M26 Pershing</span> American medium/heavy battle tank (1944–1951)

The M26 Pershing is a heavy tank, later designated as a medium tank, formerly used by the United States Army. It was used in the last months of World War II during the Invasion of Germany and extensively during the Korean War. The tank was named after General of the Armies John J. Pershing, who led the American Expeditionary Force in Europe in World War I.

This page details tank production by the United States of America during World War II.

<span class="mw-page-title-main">M3 Stuart</span> WW2 American light tank

The M3 Stuart/light tank M3, was an American light tank of World War II. An improved version of the tank entered service as the M5 in 1942 to be supplied to British and other Commonwealth forces under lend-lease prior to the entry of the U.S. into the war. Afterwards, it was used by U.S. and Allied forces until the end of the war.

<span class="mw-page-title-main">Type 97 Chi-Ha medium tank</span> Medium tank

The Type 97 Chi-Ha was a medium tank used by the Imperial Japanese Army during the Second Sino-Japanese War, the Battles of Khalkhin Gol against the Soviet Union, and the Second World War. It was the most widely produced Japanese medium tank of World War II.

<span class="mw-page-title-main">Flame tank</span> Armored vehicle equipped with a flamethrower

A flame tank is a type of tank equipped with a flamethrower, most commonly used to supplement combined arms attacks against fortifications, confined spaces, or other obstacles. The type only reached significant use in the Second World War, during which the United States, Nazi Germany, Soviet Union, Italy, Japan, and the United Kingdom all produced flamethrower-equipped tanks.

<span class="mw-page-title-main">M10 tank destroyer</span> WW2 American tank destroyer

The M10 tank destroyer, formally known as 3-inch gun motor carriage M10 or M10 GMC, was an American tank destroyer of World War II. After US entry into World War II and the formation of the Tank Destroyer Force, a suitable vehicle was needed to equip the new battalions. By November 1941, the Army requested a vehicle with a gun in a fully rotating turret after other interim models were criticized for being too poorly designed. The prototype of the M10 was conceived in early 1942 and delivered in April that year. After appropriate changes to the hull and turret were made, the modified version was selected for production in June 1942 as the "3-inch Gun Motor Carriage M10". It mounted the 3-inch gun M7 in a rotating turret on a modified M4 Sherman tank chassis.

<span class="mw-page-title-main">M3 half-track</span> US military vehicle

The M3 half-track was an American armored personnel carrier half-track widely used by the Allies during World War II and in the Cold War. Derived from the M2 half-track car, the M3 was extensively produced, with about 15,000 standard M3s and more than 38,000 variant units manufactured.

<span class="mw-page-title-main">M2 light tank</span> 1930s United States light tank

The M2 light tank, officially Light Tank, M2, was an American light tank of the interwar period which saw limited service during World War II. The most common model, the M2A4, was equipped with one 37 mm (1.5 in) M5 gun and five .30 cal M1919 Browning machine guns.

<span class="mw-page-title-main">Tanks in World War II</span>

Tanks were an important weapons system in World War II. Although tanks in the inter-war years were the subject of widespread research, few were made, in just a few countries. However, during World War II, most armies employed tanks, and thousands were built every month. Tank usage, doctrine, and production varied widely among the combatant nations. By war's end, a consensus was forming on tank doctrine and design.

<span class="mw-page-title-main">37 mm gun M3</span> American anti-tank gun

The 37 mm gun M3 is the first dedicated anti-tank gun fielded by United States forces in numbers. Introduced in 1940, it became the standard anti-tank gun of the U.S. infantry with its size enabling it to be pulled by a jeep. However, the continuing improvement of German tanks quickly rendered the 37 mm ineffective and, by 1943, it was being gradually replaced in the European and Mediterranean theaters by the more powerful British-developed 57 mm gun M1. In the Pacific, where the Japanese tank threat was less significant, the M3 remained in service until the end of the war, but some 57mm guns were issued.

<span class="mw-page-title-main">M2 medium tank</span> American medium battle tank

The M2 medium tank, officially Medium Tank, M2, was a United States Army medium tank that was first produced in 1939 by the Rock Island Arsenal, just prior to the commencement of the Second World War in Europe. Production was 18 M2 tanks, and 94 slightly improved M2A1 tanks, for a total of 112. Events in Western Europe rapidly demonstrated that the M2 was obsolete, and it was never used overseas in combat; it was, however, used for training purposes throughout the war.

<span class="mw-page-title-main">T20 medium tank</span> Series of armored fighting vehicles designed by the United States

The medium tank T20, medium tank T22 and medium tank T23 were prototype medium tanks, developed by the United States Army during World War II. They were designed as successors to the M4 Sherman. The standard main weapon for production versions of these designs was to be the 76 mm gun M1.

<span class="mw-page-title-main">76 mm gun M1</span> American tank gun

The 76 mm gun M1 was an American World War II–era tank gun developed by the U.S United States Ordnance Department in 1942 to supplement the 75 mm gun on the basic Medium tank M4. It was also used to arm the M18 Hellcat tank destroyer.

<span class="mw-page-title-main">M3 Gun Motor Carriage</span> American tank destroyer

The M3 gun motor carriage was a United States Army tank destroyer equipped with a 75 mm M1897A4 gun, which was built by the Autocar Company during World War II.

<span class="mw-page-title-main">Tanks of the United States</span> Evolution of American Tanks

The United States has produced tanks since their inception in World War I, up until the present day. While there were several American experiments in tank design, the first American tanks to see service were copies of French light tanks and a joint heavy tank design with the United Kingdom.

<span class="mw-page-title-main">M7 medium tank</span> WW2 American tank

The M7 medium tank, initially T7 light tank, was an American tank, originally conceived as an up-gunned replacement for the M3/M5 light tank ("Stuart"). The project developed to mount the same 75mm armament as the M4 Sherman while retaining the light weight and maneuverability of the M3 Stuart; however, during development the weight of the prototype surpassed the US Army's standard for light tanks and crossed into the medium tank category and was renamed. The M7 had significantly less armor than the M4 Sherman, no greater firepower, and held only a slight advantage in top speed. For these reasons, and because the M4 was already battle-tested and in full production, the M7 was cancelled in 1943.