Carnot cycle

A Carnot cycle is an ideal thermodynamic cycle proposed by French physicist Sadi Carnot in 1824 and expanded upon by others in the 1830s and 1840s. By Carnot's theorem, it provides an upper limit on the efficiency of any classical thermodynamic engine during the conversion of heat into work, or conversely, the efficiency of a refrigeration system in creating a temperature difference through the application of work to the system.

In a Carnot cycle, a system or engine transfers energy in the form of heat between two thermal reservoirs at temperatures ${\displaystyle T_{H}}$ and ${\displaystyle T_{C}}$ (referred to as the hot and cold reservoirs, respectively), and a part of this transferred energy is converted to the work done by the system. The cycle is reversible, and entropy is conserved, merely transferred between the thermal reservoirs and the system without gain or loss. When work is applied to the system, heat moves from the cold to hot reservoir (heat pump or refrigeration). When heat moves from the hot to the cold reservoir, the system applies work to the environment. The work ${\displaystyle W}$ done by the system or engine to the environment per Carnot cycle depends on the temperatures of the thermal reservoirs and the entropy transferred from the hot reservoir to the system ${\displaystyle \Delta S}$ per cycle such as ${\displaystyle W=(T_{H}-T_{C})\Delta S=(T_{H}-T_{C}){\frac {Q_{H}}{T_{H}}}}$, where ${\displaystyle Q_{H}}$ is heat transferred from the hot reservoir to the system per cycle.

External videos
Carnot cycle from The Mechanical Universe

Stages

A Carnot cycle as an idealized thermodynamic cycle performed by a Carnot heat engine, consisting of the following steps:

1. 

   Isothermal expansion. Heat (as an energy) is transferred reversibly from hot temperature reservoir at constant temperature T_H to the gas at temperature infinitesimally less than T_H (to allow heat transfer to the gas without practically changing the gas temperature so isothermal heat addition or absorption). During this step (1 to 2 on Figure 1 , A to B in Figure 2 ), the gas is thermally in contact with the hot temperature reservoir (while thermally isolated from the cold temperature reservoir) and the gas is allowed to expand, doing work on the surroundings by gas pushing up the piston (stage 1 figure, right). Although the pressure drops from points 1 to 2 (figure 1) the temperature of the gas does not change during the process because the heat transferred from the hot temperature reservoir to the gas is exactly used to do work on the surroundings by the gas, so no gas internal energy changes (no gas temperature change for an ideal gas). Heat Q_H > 0 is absorbed from the hot temperature reservoir, resulting in an increase in the entropy ${\displaystyle S}$ of the gas by the amount ${\displaystyle \Delta S_{H}=Q_{H}/T_{H}}$.

2. 

   Isentropic (reversible adiabatic) expansion of the gas (isentropic work output). For this step (2 to 3 on Figure 1 , B to C in Figure 2 ) the gas in the engine is thermally insulated from both the hot and cold reservoirs, thus they neither gain nor lose heat, an 'adiabatic' process. The gas continues to expand with reduction of its pressure, doing work on the surroundings (raising the piston; stage 2 figure, right), and losing an amount of internal energy equal to the work done. The gas expansion without heat input causes the gas to cool to the "cold" temperature (by losing its internal energy), that is infinitesimally higher than the cold reservoir temperature T_C. The entropy remains unchanged as no heat Q transfers (Q = 0) between the system (the gas) and its surroundings, so an isentropic process, meaning no entropy change in the process).

3. 

   Isothermal compression. Heat transferred reversibly to low temperature reservoir at constant temperature T_C (isothermal heat rejection). In this step (3 to 4 on Figure 1 , C to D on Figure 2 ), the gas in the engine is in thermal contact with the cold reservoir at temperature T_C (while thermally isolated from the hot temperature reservoir) and the gas temperature is infinitesimally higher than this temperature (to allow heat transfer from the gas to the cold reservoir without practically changing the gas temperature). The surroundings do work on the gas, pushing the piston down (stage 3 figure, right). An amount of energy earned by the gas from this work exactly transfers as a heat energy Q_C < 0 (negative as leaving from the system, according to the universal convention in thermodynamics) to the cold reservoir so the entropy of the system decreases by the amount ${\displaystyle \Delta S_{C}=Q_{C}/T_{C}}$. ^[1] ${\displaystyle \Delta S_{C}<0}$ because the isothermal compression decreases the multiplicity of the gas.

4. 

   Isentropic compression. (4 to 1 on Figure 1 , D to A on Figure 2 ) Once again the gas in the engine is thermally insulated from the hot and cold reservoirs, and the engine is assumed to be frictionless and the process is slow enough, hence reversible. During this step, the surroundings do work on the gas, pushing the piston down further (stage 4 figure, right), increasing its internal energy, compressing it, and causing its temperature to rise back to the temperature infinitesimally less than T_H due solely to the work added to the system, but the entropy remains unchanged. At this point the gas is in the same state as at the start of step 1.

Figure 1: A Carnot cycle illustrated on a PV diagram to illustrate the work done. 1-to-2 (isothermal expansion), 2-to-3 (isentropic expansion), 3-to-4 (isothermal compression), 4-to-1 (isentropic compression).

In this case, since it is a reversible thermodynamic cycle (no net change in the system and its surroundings per cycle) ^{[2] [1]}

$${\displaystyle \Delta S_{H}+\Delta S_{C}=\Delta S_{\text{cycle}}=0,}$$

or,

$${\displaystyle {\frac {Q_{H}}{T_{H}}}=-{\frac {Q_{C}}{T_{C}}}.}$$

This is true as ${\displaystyle Q_{C}}$ and ${\displaystyle T_{C}}$ are both smaller in magnitude and in fact are in the same ratio as ${\displaystyle Q_{H}/T_{H}}$.

The pressure–volume graph

When a Carnot cycle is plotted on a pressure–volume diagram ( Figure 1 ), the isothermal stages follow the isotherm lines for the working fluid, the adiabatic stages move between isotherms, and the area bounded by the complete cycle path represents the total work that can be done during one cycle. From point 1 to 2 and point 3 to 4 the temperature is constant (isothermal process). Heat transfer from point 4 to 1 and point 2 to 3 are equal to zero (adiabatic process).

Properties and significance

The temperature–entropy diagram

Main article: Temperature–entropy diagram

Figure 2: A Carnot cycle as an idealized thermodynamic cycle performed by a Carnot heat engine), illustrated on a TS (temperature T–entropy S) diagram. The cycle takes place between a hot reservoir at temperature T_H and a cold reservoir at temperature T_C. The vertical axis is the system temperature, the horizontal axis is the system entropy. A-to-B (isothermal expansion), B-to-C (isentropic expansion), C-to-D (isothermal compression), D-to-A (isentropic compression).

Figure 3: A generalized thermodynamic cycle taking place between a hot reservoir at temperature T_H and a cold reservoir at temperature T_C. By the second law of thermodynamics, the cycle cannot extend outside the temperature band from T_C to T_H. The area in red, |Q_C|, is the amount of energy exchanged between the system and the cold reservoir. The area in white, W, is the amount of work energy exchanged by the system with its surroundings. The amount of heat exchanged with the hot reservoir is the sum of the two. If the system is behaving as an engine, the process moves clockwise around the loop, and moves counter-clockwise if it is behaving as a refrigerator. The efficiency to the cycle is the ratio of the white area (work) divided by the sum of the white and red areas (heat absorbed from the hot reservoir).
Q _C (energy lost to the cold reservoir) can be seen as a direct subtraction, or expressed as the sum of a negative quantity, which can lead to different conventions.

The behavior of a Carnot engine or refrigerator is best understood by using a temperature–entropy diagram (T–S diagram), in which the thermodynamic state is specified by a point on a graph with entropy (S) as the horizontal axis and temperature (T) as the vertical axis ( Figure 2 ). For a simple closed system (control mass analysis), any point on the graph represents a particular state of the system. A thermodynamic process is represented by a curve connecting an initial state (A) and a final state (B). The area under the curve is:

${\displaystyle Q=\int _{A}^{B}dQ=\int _{A}^{B}T\,dS}$

(1)

which is the amount of heat transferred in the process. If the process moves the system to greater entropy, the area under the curve is the amount of heat absorbed by the system in that process; otherwise, it is the amount of heat removed from or leaving the system. For any cyclic process, there is an upper portion of the cycle and a lower portion. In T-S diagrams for a clockwise cycle, the area under the upper portion will be the energy absorbed by the system during the cycle, while the area under the lower portion will be the energy removed from the system during the cycle. The area inside the cycle is then the difference between the two (the absorbed net heat energy), but since the internal energy of the system must have returned to its initial value, this difference must be the amount of work done by the system per cycle. Referring to Figure 1 , mathematically, for a reversible process, we may write the amount of work done over a cyclic process as:

${\displaystyle W=\oint PdV=\oint (dQ-dU)=\oint (TdS-dU)=\oint TdS-\oint dU=\oint TdS}$

(2)

Since dU is an exact differential, its integral over any closed loop is zero and it follows that the area inside the loop on a T–S diagram is (a) equal to the total work performed by the system on the surroundings if the loop is traversed in a clockwise direction, and (b) is equal to the total work done on the system by the surroundings as the loop is traversed in a counterclockwise direction.

Figure 4: A Carnot cycle taking place between a hot reservoir at temperature T_H and a cold reservoir at temperature T_C.

The Carnot cycle

Figure 5: A visualization of a Carnot cycle

Evaluation of the above integral is particularly simple for a Carnot cycle. The amount of energy transferred as work is

$${\displaystyle W=\oint PdV=\oint TdS=(T_{H}-T_{C})(S_{B}-S_{A})}$$

The total amount of heat transferred from the hot reservoir to the system (in the isothermal expansion) will be

$${\displaystyle Q_{H}=T_{H}(S_{B}-S_{A})=T_{H}\Delta S_{H}}$$

and the total amount of heat transferred from the system to the cold reservoir (in the isothermal compression) will be

$${\displaystyle Q_{C}=T_{C}(S_{A}-S_{B})=T_{C}\Delta S_{C}<0}$$

Due to energy conservation, the net heat transferred, ${\displaystyle Q}$, is equal to the work performed ^[1]

$${\displaystyle W=Q=Q_{H}-Q_{C}}$$

The efficiency ${\displaystyle \eta }$ is defined to be:

${\displaystyle \eta ={\frac {W}{Q_{H}}}={\frac {Q_{H}-Q_{C}}{Q_{H}}}=1-{\frac {T_{C}}{T_{H}}}}$

(3)

where

• W is the work done by the system (energy exiting the system as work),
• ${\displaystyle Q_{C}}$ < 0 is the heat taken from the system (heat energy leaving the system),
• ${\displaystyle Q_{H}}$ > 0 is the heat put into the system (heat energy entering the system),
• ${\displaystyle T_{C}}$ is the absolute temperature of the cold reservoir, and
• ${\displaystyle T_{H}}$ is the absolute temperature of the hot reservoir.
• ${\displaystyle S_{B}}$ is the maximum system entropy
• ${\displaystyle S_{A}}$ is the minimum system entropy

The expression with the temperature ${\displaystyle \eta =1-{\frac {T_{C}}{T_{H}}}}$ can be derived from the expressions above with the entropy: ${\displaystyle Q_{H}=T_{H}(S_{B}-S_{A})=T_{H}\Delta S_{H}}$ and ${\displaystyle Q_{C}=T_{C}(S_{A}-S_{B})=T_{C}\Delta S_{C}<0}$. Since ${\displaystyle \Delta S_{C}=S_{A}-S_{B}=-\Delta S_{H}}$, a minus sign appears in the final expression for ${\displaystyle \eta }$.

This is the Carnot heat engine working efficiency definition as the fraction of the work done by the system to the thermal energy received by the system from the hot reservoir per cycle. This thermal energy is the cycle initiator.

Reversed Carnot cycle

A Carnot heat-engine cycle described is a totally reversible cycle. That is, all the processes that compose it can be reversed, in which case it becomes the Carnot heat pump and refrigeration cycle. This time, the cycle remains exactly the same except that the directions of any heat and work interactions are reversed. Heat is absorbed from the low-temperature reservoir, heat is rejected to a high-temperature reservoir, and a work input is required to accomplish all this. The P–V diagram of the reversed Carnot cycle is the same as for the Carnot heat-engine cycle except that the directions of the processes are reversed. ^[3]

Carnot's theorem

Main article: Carnot's theorem (thermodynamics)

It can be seen from the above diagram that for any cycle operating between temperatures ${\displaystyle T_{H}}$ and ${\displaystyle T_{C}}$, none can exceed the efficiency of a Carnot cycle.

Figure 6: A real engine (left) compared to the Carnot cycle (right). The entropy of a real material changes with temperature. This change is indicated by the curve on a T–S diagram. For this figure, the curve indicates a vapor-liquid equilibrium (See Rankine cycle ). Irreversible systems and losses of energy (for example, work due to friction and heat losses) prevent the ideal from taking place at every step.

Carnot's theorem is a formal statement of this fact: No engine operating between two heat reservoirs can be more efficient than a Carnot engine operating between those same reservoirs. Thus, Equation 3 gives the maximum efficiency possible for any engine using the corresponding temperatures. A corollary to Carnot's theorem states that: All reversible engines operating between the same heat reservoirs are equally efficient. Rearranging the right side of the equation gives what may be a more easily understood form of the equation, namely that the theoretical maximum efficiency of a heat engine equals the difference in temperature between the hot and cold reservoir divided by the absolute temperature of the hot reservoir. Looking at this formula an interesting fact becomes apparent: Lowering the temperature of the cold reservoir will have more effect on the ceiling efficiency of a heat engine than raising the temperature of the hot reservoir by the same amount. In the real world, this may be difficult to achieve since the cold reservoir is often an existing ambient temperature.

In other words, the maximum efficiency is achieved if and only if entropy does not change per cycle. An entropy change per cycle is made, for example, if there is friction leading to dissipation of work into heat. In that case, the cycle is not reversible and the Clausius theorem becomes an inequality rather than an equality. Otherwise, since entropy is a state function, the required dumping of heat into the environment to dispose of excess entropy leads to a (minimal) reduction in efficiency. So Equation 3 gives the efficiency of any reversible heat engine.

In mesoscopic heat engines, work per cycle of operation in general fluctuates due to thermal noise. If the cycle is performed quasi-statically, the fluctuations vanish even on the mesoscale. ^[4] However, if the cycle is performed faster than the relaxation time of the working medium, the fluctuations of work are inevitable. Nevertheless, when work and heat fluctuations are counted, an exact equality relates the exponential average of work performed by any heat engine to the heat transfer from the hotter heat bath. ^[5]

Efficiency of real heat engines

See also: Heat Engine § Efficiency

Carnot realized that, in reality, it is not possible to build a thermodynamically reversible engine. So, real heat engines are even less efficient than indicated by Equation 3 . In addition, real engines that operate along the Carnot cycle style (isothermal expansion / isentropic expansion / isothermal compression / isentropic compression) are rare. Nevertheless, Equation 3 is extremely useful for determining the maximum efficiency that could ever be expected for a given set of thermal reservoirs.

Although Carnot's cycle is an idealization, Equation 3 as the expression of the Carnot efficiency is still useful. Consider the average temperatures,

$${\displaystyle \langle T_{H}\rangle ={\frac {1}{\Delta S}}\int _{Q_{\text{in}}}TdS}$$

$${\displaystyle \langle T_{C}\rangle ={\frac {1}{\Delta S}}\int _{Q_{\text{out}}}TdS}$$

at which the first integral is over a part of a cycle where heat goes into the system and the second integral is over a cycle part where heat goes out from the system. Then, replace T_H and T_C in Equation 3 by ⟨T_H⟩ and ⟨T_C⟩, respectively, to estimate the efficiency a heat engine.

For the Carnot cycle, or its equivalent, the average value ⟨T_H⟩ will equal the highest temperature available, namely T_H, and ⟨T_C⟩ the lowest, namely T_C. For other less efficient thermodynamic cycles, ⟨T_H⟩ will be lower than T_H, and ⟨T_C⟩ will be higher than T_C. This can help illustrate, for example, why a reheater or a regenerator can improve the thermal efficiency of steam power plants and why the thermal efficiency of combined-cycle power plants (which incorporate gas turbines operating at even higher temperatures) exceeds that of conventional steam plants. The first prototype of the diesel engine was based on the principles of the Carnot cycle.

As a macroscopic construct

Main article: Carnot heat engine § As a macroscopic construct

The Carnot heat engine is, ultimately, a theoretical construct based on an idealized thermodynamic system. On a practical human-scale level the Carnot cycle has proven a valuable model, as in advancing the development of the diesel engine. However, on a macroscopic scale limitations placed by the model's assumptions prove it impractical, and, ultimately, incapable of doing any work. ^[6] As such, per Carnot's theorem, the Carnot engine may be thought as the theoretical limit of macroscopic scale heat engines rather than any practical device that could ever be built. ^[7]

See also

• Carnot heat engine
• Reversible process (thermodynamics)

References

Notes

1. Planck, M. (1945). "equations 39, 40 and 65 in sections §90 & §137". Treatise on Thermodynamics. Dover Publications. pp. 75, 135.
2. Fermi, E. (1956). "equation 64". Thermodynamics (PDF). Dover Publications. p. 48.
3. Çengel, Yunus A., and Michael A. Boles. Thermodynamics: An Engineering Approach. 7th ed. New York: McGraw-Hill, 2011. p. 299. Print.
4. Holubec Viktor and Ryabov Artem (2018). "Cycling Tames Power Fluctuations near Optimum Efficiency". Phys. Rev. Lett. 121 (12): 120601. arXiv: 1805.00848 . Bibcode:2018PhRvL.121l0601H. doi:10.1103/PhysRevLett.121.120601. PMID   30296120. S2CID   52943273.
5. N. A. Sinitsyn (2011). "Fluctuation Relation for Heat Engines". J. Phys. A: Math. Theor. 44 (40): 405001. arXiv: 1111.7014 . Bibcode:2011JPhA...44N5001S. doi:10.1088/1751-8113/44/40/405001. S2CID   119261929.
6. Liu, Hang; Meng, Xin-He (18 August 2017). "Effects of dark energy on the efficiency of charged AdS black holes as heat engines". The European Physical Journal C. 77 (8): 556. arXiv: 1704.04363 . doi:10.1140/epjc/s10052-017-5134-9. ISSN   1434-6052. ...since the Carnot heat engine, setting an upper bound on the efficiency of a heat engine is an ideal, reversible engine of which a single cycle must be performed in infinite time which is impractical and so the Carnot engine has zero power.
7. Benenti, Giuliano; Casati, Giulio; Wang, Jiao (2020). "Power, efficiency, and fluctuations in steady-state heat engines" (PDF). Physical Review E. 102 (4). However, fluctuations [in reservoir temperature] make impractical such engines.

Sources

• Carnot, Sadi, Reflections on the Motive Power of Fire
• Ewing, J. A. (1910) The Steam-Engine and Other Engines edition 3, page 62, via Internet Archive
• Feynman, Richard P.; Leighton, Robert B.; Sands, Matthew (1963). The Feynman Lectures on Physics . Addison-Wesley Publishing Company. pp.  Chapter 44. ISBN   978-0-201-02116-5.
• Halliday, David; Resnick, Robert (1978). Physics (3rd ed.). John Wiley & Sons. pp.  541–548. ISBN   978-0-471-02456-9.
• Kittel, Charles; Kroemer, Herbert (1980). Thermal Physics (2nd ed.). W. H. Freeman Company. ISBN   978-0-7167-1088-2.
• Kostic, M (2011). "Revisiting The Second Law of Energy Degradation and Entropy Generation: From Sadi Carnot's Ingenious Reasoning to Holistic Generalization". AIP Conf. Proc. AIP Conference Proceedings. 1411 (1): 327–350. Bibcode:2011AIPC.1411..327K. CiteSeerX   10.1.1.405.1945 . doi:10.1063/1.3665247. American Institute of Physics, 2011. ISBN   978-0-7354-0985-9. Abstract at: . Full article (24 pages ), also at .

External links

• Hyperphysics article on the Carnot cycle.
• S. M. Blinder Carnot Cycle on Ideal Gas powered by Wolfram Mathematica