Chef's knife

Last updated
A European style of chef's knife Chef's Knife.jpg
A European style of chef's knife

In cooking, a chef's knife, also known as a cook's knife, is a cutting tool used in food preparation. The chef's knife was originally designed primarily to slice and disjoint large cuts of beef. Today it is the primary general utility knife for most Western cooks.

Contents

A European chef's knife generally has a blade 20 centimetres (8 inches) in length and a broad 4 cm (1½ in.) width, although individual models range from 15 to 36 centimetres (6 to 14 inches) in length and may be as slender as 2 cm (¾ inch). Longer and wider knives are more frequently called chef's knives, whereas shorter & more slender knives have a tendency to be called cook's knives. The shortest and narrowest knives overlap into the general utility kitchen knife category that are too narrow to have a heel to the blade, like the smaller paring knife.

Chef's knife Chef's knife.jpg
Chef's knife

There are two common types of blade shape in Western chef's knives: French and German.

Japanese kitchen knives differ from the European style as the latter typically have a thickened heel at the base of the blade where it meets the handle at the bolster. This heel is often shaped into the handle's form at the bolster. This can clearly be seen in the photograph above. The handle is typically bi-laterally flatted to allow for it to be rivetted together through the tang, whereas the oriental style typically has an off-circular cross-section. In Japanese kitchen knives, the blade and tang has little difference in thickness throughout it length, except at the tip when sharpened - there is no bolster - it is inserted into the handle with a separate collar to hold the assembled knife together.

With modern kitchen knives, these distinct styles have merged to a degree and particular characteristics have been swapped between the two regions, as can be seen in the photograph of the kitchen knife below.

Japanese kitchen knives have come under Western influence since the Meiji era, and many hybrid versions are available. The gyuto ( 牛刀 ぎゅうとう, gyūtō) 'beef knife' is the Japanese term for a French (or Western) chef's knife. The gyuto were originally, and sometimes still called yo-boucho 洋包丁 meaning 'Western chefs knife'.

The santoku 'three-virtue' knife is a style hybridized with traditional knives for more functionality. It is smaller, lighter and sharper with a different blade shape. [1]

The Chinese chef's knife is completely different and resembles a cleaver. It is, however, functionally analogous to the Western chef's knife in that it's a general-purpose knife not designed for breaking bones.

A modern chef's knife is a multi-purpose knife designed to perform well at many differing kitchen tasks, rather than excelling at any one in particular. It can be used for mincing, slicing, and chopping vegetables, slicing meat, and disjointing large cuts.

Physical characteristics

NSF certified stamped x50CrMov15 stainless steel chef's knife with TPE grip Victorinox Fibrox 5.2063.20 chef's knife.jpg
NSF certified stamped x50CrMov15 stainless steel chef's knife with TPE grip

Chef's knives are made with blades that are either forged or stamped:

The blade of a chef's knife is typically made of carbon steel, stainless steel, or a laminate or folded sandwich of both metals, otherwise it will be a glass-like ceramic:

Handles are made of wood, steel, or synthetic/composite materials.

Edge

The edge may be ground in different ways:

In order to improve the chef's knife's multi-purpose abilities, some users employ differential sharpening along the length of the blade. The fine tip, used for precision work such as mincing, might be ground with a very sharp, acute cutting bevel; the midsection or belly of the blade receives a moderately sharp edge for general cutting, chopping and slicing, while the heavy heel or back of the cutting edge is given a strong, thick edge for heavy-duty tasks, for example disjointing beef. This differential sharpening suits European chef's knives with the heavy heel of the blade at the base at the bolster.

Technique

Holding a knife by its bolster Chef's knife grip.jpg
Holding a knife by its bolster

Technique for the use of a chef's knife depends on how well the knife is balanced as well as an individual stylistic preference. For more precise control, especially with longer heavier knives, most cooks prefer to grip the blade itself, with the thumb and the index finger grasping the blade just to the front of the finger guard and the middle finger placed just opposite, on the handle side of the finger guard below the bolster. This is commonly referred to as a 'pinch grip'. [5] Those without culinary training often grip the handle, with all four fingers and the thumb gathered underneath.[ citation needed ]

For fine slicing, the handle is raised up and down while the tip remains in contact with the cutting board and the cut object is pushed under the blade. [6]

Another technique is to hold the food being cut with one hand and to run the flat of the blade along the knuckles, utilising them as a guide. This enables the efficient use of both the curvature and the length of the blade's edge to execute the cut.

See also

Notes

  1. DEDIJER, S. (1979-03-23). "Good Menus and Fine Recipes for Absent Cooks". Science. 203 (4386): 1195. Bibcode:1979Sci...203.1195D. doi:10.1126/science.203.4386.1195. ISSN   0036-8075. PMID   17841122.
  2. farahatif (2022-12-18). "Kiritsuke knife vs Chef Knife - A detailed article". kitchenvillas.com. Retrieved 2022-12-21.
  3. "VG10 Features". Takefu Special Steel Co., Ltd. Retrieved 11 November 2016.
  4. 1 2 3 4 "Knife Edge Grind Types Illustrated". zknives.com. Retrieved 2010-05-07.
  5. Peter Hertzmann (2007), Knife Skills Illustrated: A User's Manual, W. W. Norton & Company, p. 26, ISBN   9780393061789, The proper way to hold most knives is with a "pinch grip".
  6. Alissa (2022-12-18), "Chef Knife Hold", damascuscollection.com, retrieved 2022-12-21

Related Research Articles

<span class="mw-page-title-main">Knife</span> Tool or weapon with a cutting edge or blade

A knife is a tool or weapon with a cutting edge or blade, usually attached to a handle or hilt. One of the earliest tools used by humanity, knives appeared at least 2.5 million years ago, as evidenced by the Oldowan tools. Originally made of wood, bone, and stone, over the centuries, in step with improvements in both metallurgy and manufacturing, knife blades have been made from copper, bronze, iron, steel, ceramic, and titanium. Most modern knives have either fixed or folding blades; blade patterns and styles vary by maker and country of origin.

<span class="mw-page-title-main">Blade</span> Sharp cutting part of a weapon or tool

A blade is the sharp, cutting portion of a tool, weapon, or machine, specifically designed to puncture, chop, slice, or scrape surfaces or materials. Blades are typically made from materials that are harder than those they are intended to cut. This includes early examples made from flaked stones like flint or obsidian, evolving through the ages into metal forms like copper, bronze, and iron, and culminating in modern versions made from steel or ceramics. Serving as one of humanity's oldest tools, blades continue to have wide-ranging applications, including in combat, cooking, and various other everyday and specialized tasks.

<span class="mw-page-title-main">Japanese kitchen knife</span> Type of knife used for food preparation

A Japanese kitchen knife is a type of kitchen knife used for food preparation. These knives come in many different varieties and are often made using traditional Japanese blacksmithing techniques. They can be made from stainless steel, or hagane, which is the same kind of steel used to make Japanese swords. Most knives are referred to as hōchō or the variation -bōchō in compound words but can have other names including -kiri. There are four general categories used to distinguish the Japanese knife designs: handle, blade grind, steel, and construction.

<span class="mw-page-title-main">Grind</span> Cross sectional shape of a blade in a plane normal to its edge

A blade's grind is its cross-sectional shape in a plane normal to the edge. Grind differs from blade profile, which is the blade's cross-sectional shape in the plane containing the blade's edge and the centre contour of the blade's back. The grind of a blade should not be confused with the bevel forming the sharpened edge; it more usually describes the overall cross-section of the blade, not inclusive of the beveled cutting edge which is typically of a different, less acute angle as the bevel ground onto the blade to give it a cross-sectional shape. For example, the famous Buck 110 hunting knife has a "hollow ground" blade, with concave blade faces, but the cutting edge itself is a simple, flat-ground bevel of lesser angle. It would be difficult, if not impossible, to put a "hollow grind" onto the actual cutting edge of the blade itself, which is a very narrow and small bevel.

<span class="mw-page-title-main">Kitchen knife</span> Knives intended for use in the process of preparing food

A kitchen knife is any knife that is intended to be used in food preparation. While much of this work can be accomplished with a few general-purpose knives – notably a large chef's knife, a tough cleaver, a small paring knife and some sort of serrated blade – there are also many specialized knives that are designed for specific tasks. Kitchen knives can be made from several different materials.

<i>Santoku</i> Kitchen knife originating in Japan

The santoku bōchō(Japanese: 三徳包丁, 'three virtues knife' or 'three uses knife') or bunka bōchō(文化包丁) is a general-purpose kitchen knife originating in Japan. Its blade is typically between 13 and 20 cm long, and has a flat edge. The santoku has a sheepsfoot blade that curves down an angle approaching 60 degrees at the point. The bunka bōchō, however, has a k-tip. The term santoku may refer to the wide variety of ingredients that the knife can handle: fish, meat, and vegetables, or to the tasks it can perform: chopping, dicing, and slicing, with either interpretation indicating a multi-use, general-purpose kitchen knife. The term bunka, refers to how it is used for the cultural food of Japan. The blade and handle of the santoku are designed to work in harmony by matching the blade's width and weight to the weight of the tang and the handle.

WÜSTHOF is a knife-maker based in Solingen, Germany. Family owned for seven generations, the company's main products are mid-priced to high-end kitchen knives for domestic and professional use. WÜSTHOF is one of the leading manufacturers of chef's knives.

Spyderco is an American cutlery company based in Golden, Colorado, producing knives and knife sharpeners. Spyderco pioneered many features that are now common in folding knives, including the pocket clip, serrations, and the opening hole. Spyderco has collaborated with 30 custom knife makers, athletes, and self-defense instructors for designs and innovated the usage of 20 different blade materials.

<span class="mw-page-title-main">Sharpening</span> Creating or refining the edge of a cutting tool

Sharpening is the process of creating or refining the edge joining two non-coplanar faces into a converging apex, thereby creating an edge of appropriate shape on a tool or implement designed for cutting. Sharpening is done by removing material on an implement with an abrasive substance harder than the material of the implement, followed sometimes by processes to polish/hone the sharp surface to increase smoothness.

<span class="mw-page-title-main">Ceramic knife</span> Knife with a blade made out of non-metallic material

A ceramic knife is a knife with a ceramic blade typically made from zirconium dioxide (ZrO2; also known as zirconia), rather than the steel used for most knives. Ceramic knife blades are usually produced through the dry-pressing and firing of powdered zirconia using solid-state sintering. The blades typically score 8.5 on the Mohs scale of mineral hardness, compared to 4.5 for normal steel and 7.5 to 8 for hardened steel and 10 for diamond. The resultant blade has a hard edge that stays sharp for much longer than conventional steel blades. However, the blade is brittle, subject to chipping, and will break rather than flex if twisted. The ceramic blade is sharpened by grinding the edges with a diamond-dust-coated grinding wheel.

<span class="mw-page-title-main">Knife making</span> Process of manufacturing a knife

Knife making is the process of manufacturing a knife by any one or a combination of processes: stock removal, forging to shape, welded lamination or investment cast. Typical metals used come from the carbon steel, tool, or stainless steel families. Primitive knives have been made from bronze, copper, brass, iron, obsidian, and flint.

<span class="mw-page-title-main">Cleaver</span> Big knife

A cleaver is a large knife that varies in its shape but usually resembles a rectangular-bladed hatchet. It is largely used as a kitchen or butcher knife and is mostly intended for splitting up large pieces of soft bones and slashing through thick pieces of meat. The knife's broad side can also be used for crushing in food preparation and can also be used to scoop up chopped items.

<span class="mw-page-title-main">Global (cutlery)</span> Japanese cutlery manufacturer

GLOBAL is a Japanese brand of kitchen knives and accessory tools owned and manufactured by the Yoshikin factory of Japan. The Yoshikin Factory is owned by the Watanabe family and located in Tsubame, Japan.

<span class="mw-page-title-main">Knife sharpening</span>

Knife sharpening is the process of making a knife or similar tool sharp by grinding against a hard, rough surface, typically a stone, or a flexible surface with hard particles, such as sandpaper. Additionally, a leather razor strop, or strop, is often used to straighten and polish an edge.

<span class="mw-page-title-main">W. R. Case & Sons Cutlery Co.</span> American manufacturer of knives

W.R. Case & Sons Cutlery Company is an American manufacturer of traditional pocket knives, fixed blades/sporting knives, kitchen knives, limited edition commemoratives and collectibles. The company originated in Little Valley, New York, around the turn of the 20th century, before relocating to its current home, Bradford, Pennsylvania, in 1905. The company's namesake, William Russell Case, first made knives with his brothers under the name Case Brothers Cutlery Company. His son, John Russell ("Russ") Case, worked as a salesman for his father's company before founding W.R. Case & Sons.

Honyaki (本焼) is the name for the Japanese traditional method of metalwork construction most often seen in kitchen knives by forging a blade, with a technique most similar to the tradition of nihonto, from a single piece of high-carbon steel covered with clay to yield upon quench a soft, resilient spine, a hamon, and a hard, sharp edge. Honyaki as a term alone can refer to either mizu honyaki (water-quench) or abura honyaki. The goal is to produce a sharper, longer lasting edge than is usually achievable with the lamination method. The term has been adapted to describe high-end mono-stainless in Japan and carbon blades by non-Japanese bladesmiths that have a hamon but are made with Western steel, heat treat, equipment, finishing, and design.

<span class="mw-page-title-main">Steak knife</span> Sharp table knife used for cutting steak

A steak knife is a sharp table knife designed to efficiently and effectively cut steak. This type of knife comes in a variety of styles and sizes; however, the design often used in a steakhouse typically features a partially serrated blade and wood handle.

<span class="mw-page-title-main">Fillet knife</span> Flexible knife used in the preparation of filets

A fillet knife is a kitchen knife used for filleting. It gives good control and aids in filleting. It is a very flexible member of the boning knife family that is used to filet and prepare fish. Fillet knife blades are typically 15 to 28 cm long. This allows them to move easily along the backbone and under the skin of meat.

<span class="mw-page-title-main">Caidao</span> Type of knife similar to a cleaver

A Chinese chef's knife — sometimes referred to as a Càidāo, a Chinese knife, the rectangular-bladed, all-purpose chef’s knife used to prepare a variety of meats, fish and vegetables. The popularity of this style of knife has spread with the associated cuisines. They resemble Western cleavers in appearance, but most Chinese chef's knives are relatively thin-bladed and designed for slicing, finely chopping and mincing vegetables, fish and boneless meats. The heavier gǔdāo are produced and are used much like Western-type meat cleavers to prepare large sides of beef, pork and other boned meats. However, Chinese-style knives of this weight are not common in the West.

References

Commons-logo.svg Media related to Chef's knives at Wikimedia Commons

Wikibooks-logo-en-noslogan.svg Cookbook:Knife skills at Wikibooks