Hafting

Last updated
An axe hafted with an adhesive Axe (AM 1918.69-3).jpg
An axe hafted with an adhesive

Hafting is a process by which an artifact, often made of bone, stone, or metal is attached to a haft (handle [1] or strap). This makes the artifact more useful by allowing it to be launched by a bow (arrow), thrown by hand (spear), or used with more effective leverage (axe). When constructed properly, hafting can tremendously improve a weapon's damage and range. It is estimated that hafted weapons were most common during the Upper Paleolithic and Middle Paleolithic. It was one of the first tools where hominins took separate elements and united them into a single tool. The development of hafting is considered by archaeologists to have been a significant milestone. It was not only an improvement in the technology at the time; it also showed the progression of the human mind toward a world of complex tool-making.

Contents

Hafting weapons is perhaps best known for its use by humans in prehistory, but it is still practiced by enthusiasts today and the handle of a tool such as an axe is still known as a haft. Many people still practice the hafting techniques by using old-fashioned methods to figure out the best way to attach a handle onto tools, while improving the overall structure and function. Hafting has evolved through the past and the idea can still be seen in the structure of modern-day tools such as hammers and axes. The methods and processes of hafting have also varied and evolved over time.

The hafting process

Flint (tool) Flintstone knife.jpg
Flint (tool)

Hafting requires a means of attaching the artifact to the strap or shaft, and to this end, flanges are often created on one end (the end opposite the cutting edge). Flanges are produced by a process of knapping or grinding the excess stone away, resulting in indentations in the piece.

If a shaft or handle is to be used, it must also be prepared in some way. Wood is frequently used. A good piece of wood has a diameter large enough to provide adequate strength yet small enough to hold comfortably for long periods of time. A common practice of hafting is to remove the outer layer of bark where the handhold would be to prevent cuts and the painful imperfections found in the bark. Attaching the tool to the shaft can be difficult which is why there are two main methods used to soften the wooden shaft including burning the end, and/or soaking it in water. These soften the material to easily allow the slits to be cut vertically into the center of the shaft. This provides a place for the "head" of the tool or weapon to fit. Alternatively, the shaft may be split down the center which allows the artifact to fully sit within the shaft, and once fully wrapped up, can be much stronger.

The artifact can then be inserted into the slit and fixed to the shaft by tying around the flanges with a suitable material. Materials such as the Australian Sea Grass Cordage and split deer intestine can be used due to its high strength and durability once installed. Some people will wrap the material around the handle as well to add grip. The main disadvantage of wrapping the tool onto the shaft arises after usage when the fibers lose their tension and become loose. High humidity is also a contributing factor to the fibers losing tension. On occasion, glue is added for extra support. When glue or any other resin is used, the hafting is said to be mastic. Mastic hafts are also very strong and reliable since there is little to no movement of the tool. Glue also has the advantage of absorbing shock when hardened, which helps with cushioning. Before industrial glue was readily available, people would use a variety of plant or animal materials to make glue. Many prehistoric types of glue were a combination of materials, such as animal feces, tree bark, and charcoal.[ citation needed ] The main downside of mastic hafts is the time consuming and difficult construction process. Alternatively, the head may simply be forced into the shaft, if the shaft is soft enough, eliminating the need for a slit (and perhaps improving durability). If a strap is used, it is tied directly to the flanges of the artifact. [2]

Generally, it takes a much longer time to create the actual haft binding than it does the tool used in the haft. The tool, such as a projectile point, typically takes up to twenty minutes whereas the haft binding takes several hours. Often many times throughout a haft's life cycle, the tool will be replaced or sharpened and reattached to the shaft to keep the haft as effective and precise as possible.

Hafting in prehistory

More than 125,000 years ago, early Archaic humans such as Homo heidelbergensis developed the extensive use of hafted stone tools. Over time, hafting evolved and tools became deadlier with more control. Evolution has brought hafts with small shafts and dull stone tools to longer stronger shafts with sharper, narrower tools that were better suited for piercing and cutting. By offsetting the diameters of a tool with a cylindrical base, and a hole in the shaft, a much more secure fit can be made, assuring the ax head stays in place. Hafting stone points, in particular, was an important advancement in the weapons of early humans. These hafted stone points increased the force and effectiveness of these tools, therefore, allowing people to hunt and kill animals more efficiently. The increased efficiency of hunting and killing animals is believed to have allowed for people of this time to have regular access to meat and other high-quality foods. The increase in the consumption of meat around this time could be directly linked to increases in brain size that are reported in the archaeology record of this time.

Multiple lines of evidence indicate that ~500,000-year-old stone points from the archaeological site of Kathu Pan 1 (KP1), South Africa, functioned as spear tips. [3] This has led teams of researchers to come to the conclusion that common ancestors of Homo sapiens and Neanderthals started hafting almost 500,000 years ago.

Aboriginal re-hafting workshops have potentially been identified at Lake George, New South Wales, dating back to the Late Holocene. [4]

See also

Related Research Articles

<span class="mw-page-title-main">Adhesive</span> Non-metallic material used to bond various materials together

Adhesive, also known as glue, cement, mucilage, or paste, is any non-metallic substance applied to one or both surfaces of two separate items that binds them together and resists their separation.

<span class="mw-page-title-main">Microlith</span> Stone tool

A microlith is a small stone tool usually made of flint or chert and typically a centimetre or so in length and half a centimetre wide. They were made by humans from around 35,000 years ago, across Europe, Africa, Asia and Australia. The microliths were used in spear points and arrowheads.

<span class="mw-page-title-main">Polearm</span> Pole-mounted close combat weapon

A polearm or pole weapon is a close combat weapon in which the main fighting part of the weapon is fitted to the end of a long shaft, typically of wood, extending the user's effective range and striking power. Polearms are predominantly melee weapons, with a subclass of spear-like designs fit for thrusting and/or throwing. Because many polearms were adapted from agricultural implements or other fairly abundant tools, and contained relatively little metal, they were cheap to make and readily available. When belligerents in warfare had a poorer class who could not pay for dedicated military weapons, they would often appropriate tools as cheap weapons. The cost of training was comparatively low, since these conscripted farmers had spent most of their lives using these "weapons" in the fields. This made polearms the favoured weapon of peasant levies and peasant rebellions the world over.

A spear is a polearm consisting of a shaft, usually of wood, with a pointed head. The head may be simply the sharpened end of the shaft itself, as is the case with fire hardened spears, or it may be made of a more durable material fastened to the shaft, such as bone, flint, obsidian, copper, bronze, iron, or steel. The most common design for hunting and/or warfare, since ancient times has incorporated a metal spearhead shaped like a triangle, diamond, or leaf. The heads of fishing spears usually feature multiple sharp points, with or without barbs.

<span class="mw-page-title-main">Mace (bludgeon)</span> Blunt striking weapon

A mace is a blunt weapon, a type of club or virge that uses a heavy head on the end of a handle to deliver powerful strikes. A mace typically consists of a strong, heavy, wooden or metal shaft, often reinforced with metal, featuring a head made of stone, bone, copper, bronze, iron, or steel.

<span class="mw-page-title-main">Arrow</span> Shafted projectile that is shot with a bow

An arrow is a fin-stabilized projectile launched by a bow. A typical arrow usually consists of a long, stiff, straight shaft with a weighty arrowhead attached to the front end, multiple fin-like stabilizers called fletchings mounted near the rear, and a slot at the rear end called a nock for engaging the bowstring. A container or bag carrying additional arrows for convenient reloading is called a quiver.

Stone tools have been used throughout human history but are most closely associated with prehistoric cultures and in particular those of the Stone Age. Stone tools may be made of either ground stone or knapped stone, the latter fashioned by a craftsman called a flintknapper. Stone has been used to make a wide variety of tools throughout history, including arrowheads, spearheads, hand axes, and querns. Knapped stone tools are nearly ubiquitous in pre-metal-using societies because they are easily manufactured, the tool stone raw material is usually plentiful, and they are easy to transport and sharpen.

<span class="mw-page-title-main">Projectile point</span> Primitive weapon component

In archaeological terminology, a projectile point is an object that was hafted to a weapon that was capable of being thrown or projected, such as a javelin, dart, or arrow. They are thus different from weapons presumed to have been kept in the hand, such as knives, spears, axes, hammers, and maces.

<span class="mw-page-title-main">Ground stone</span> Prehistoric stone tool

In archaeology, ground stone is a category of stone tool formed by the grinding of a coarse-grained tool stone, either purposely or incidentally. Ground stone tools are usually made of basalt, rhyolite, granite, or other cryptocrystalline and igneous stones whose coarse structure makes them ideal for grinding other materials, including plants and other stones.

<span class="mw-page-title-main">Spear-thrower</span> Tool to give more leverage when throwing a spear-like projectile

A spear-thrower, spear-throwing lever, or atlatl is a tool that uses leverage to achieve greater velocity in dart or javelin-throwing, and includes a bearing surface that allows the user to store energy during the throw.

<span class="mw-page-title-main">Arrowhead</span> Sharpened tip of an arrow

An arrowhead or point is the usually sharpened and hardened tip of an arrow, which contributes a majority of the projectile mass and is responsible for impacting and penetrating a target, as well as to fulfill some special purposes such as signaling.

<span class="mw-page-title-main">Dane axe</span> Viking weapon

The Dane axe or long axe is a type of European early medieval period two-handed battle axe with a very long shaft, around 0.9–1.2 metres at the low end to 1.5–1.7 metres or more at the long end. Sometimes called a broadaxe, the blade was broad and thin, intended to give a long powerful cut when swung, effective against cavalry, shields and unarmored opponents.

<span class="mw-page-title-main">Battle axe</span> Axe specifically designed for combat

A battle axe is an axe specifically designed for combat. Battle axes were specialized versions of utility axes. Many were suitable for use in one hand, while others were larger and were deployed two-handed.

<span class="mw-page-title-main">Australian Aboriginal artefacts</span> Cultural artefacts used by Aboriginal Australians

Australian Aboriginal artefacts include a variety of cultural artefacts used by Aboriginal Australians. Most Aboriginal artefacts were multi-purpose and could be used for a variety of different occupations. Spears, clubs, boomerangs and shields were used generally as weapons for hunting and in warfare. Watercraft technology artefacts in the form of dugout and bark canoes were used for transport and for fishing. Stone artefacts include cutting tools and grinding stones to hunt and make food. Coolamons and carriers such as dillybags, allowed Aboriginal peoples to carry water, food and cradle babies. Message sticks were used for communication, and ornamental artefacts for decorative and ceremonial purposes. Aboriginal children’s toys were used to both entertain and educate.

<span class="mw-page-title-main">Middle Stone Age</span> Period in African prehistory

The Middle Stone Age was a period of African prehistory between the Early Stone Age and the Late Stone Age. It is generally considered to have begun around 280,000 years ago and ended around 50–25,000 years ago. The beginnings of particular MSA stone tools have their origins as far back as 550–500,000 years ago and as such some researchers consider this to be the beginnings of the MSA. The MSA is often mistakenly understood to be synonymous with the Middle Paleolithic of Europe, especially due to their roughly contemporaneous time span; however, the Middle Paleolithic of Europe represents an entirely different hominin population, Homo neanderthalensis, than the MSA of Africa, which did not have Neanderthal populations. Additionally, current archaeological research in Africa has yielded much evidence to suggest that modern human behavior and cognition was beginning to develop much earlier in Africa during the MSA than it was in Europe during the Middle Paleolithic. The MSA is associated with both anatomically modern humans as well as archaic Homo sapiens, sometimes referred to as Homo helmei. Early physical evidence comes from the Gademotta Formation in Ethiopia, the Kapthurin Formation in Kenya and Kathu Pan in South Africa.

<span class="mw-page-title-main">Axe</span> Type of wedge tool

An axe is an implement that has been used for millennia to shape, split, and cut wood, to harvest timber, as a weapon, and as a ceremonial or heraldic symbol. The axe has many forms and specialised uses but generally consists of an axe head with a handle, also called a haft or a helve.

<span class="mw-page-title-main">Sibudu Cave</span> Rock shelter with earliest examples of modern human technology in KwaZulu-Natal, South Africa

Sibudu Cave is a rock shelter in a sandstone cliff in northern KwaZulu-Natal, South Africa. It is an important Middle Stone Age site occupied, with some gaps, from 77000 years ago to 38000 years ago.

<span class="mw-page-title-main">Mill Creek chert</span>

Mill Creek chert is a type of chert found in Southern Illinois and heavily exploited by members of the Mississippian culture. Artifacts made from this material are found in archaeological sites throughout the American Midwest and Southeast. It is named for a village and stream near the quarries, Mill Creek, Illinois and Mill Creek, a tributary of the Cache River. The chert was used extensively for the production of utilitarian tools such as hoes and spades, and for polished ceremonial objects such as bifaces, spatulate celts and maces.

The Kathu Archaeological Complex is a cluster of significant archaeological, principally Stone Age, exposures situated in and near Kathu, a mining town in the Northern Cape Province, South Africa. The sites include a suite of sinkhole exposures, the Kathu Pan sites, north west of the town, the immensely rich spread of artefacts at what is referred to as Kathu Townlands on the eastern side of Kathu, and surface and subsurface horizons including handaxes on farms further eastward. These are subject to on-going archaeological research.

<span class="mw-page-title-main">Saintie</span>

The saintie is an Indo-Persian parrying spear. It is a staff weapon that can be used both for offensive and defensive purposes. They have been produced since the 16th century and were used up to the 19th century. The use of saintie is extremely scarce today.

References

  1. Oxford English Dictionary Second Edition on CD-ROM (v. 4.0). Oxford University Press 2009
  2. Keeley, Lawrence (1982). "Hafting and Retooling: Effects on the Archaeological Record". American Antiquity. 47 (4): 789–809. doi:10.2307/280285. JSTOR   280285. S2CID   163269857.
  3. Wilkins, J.; Schoville, B. J.; Brown, K. S.; Chazan, M. (15 November 2012). "Evidence for Early Hafted Hunting Technology". Science. 6109. 338 (6109): 942–946. doi:10.1126/science.1227608. PMID   23161998. S2CID   206544031.
  4. Way, Amy Mosig; Koungoulos, Loukas; Wyatt‐Spratt, Simon; Hiscock, Peter (2023-04-26). "Investigating hafting and composite tool repair as factors creating variability in backed artefacts: Evidence from Ngungara (Weereewa/Lake George), south‐eastern Australia". Archaeology in Oceania: arco.5292. doi: 10.1002/arco.5292 . hdl: 10072/428642 . ISSN   0728-4896.

Further reading